GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc9348



Internet Engineering Task Force (IETF) D. Fedyk Request for Comments: 9348 C. Hopps Category: Standards Track LabN Consulting, L.L.C. ISSN: 2070-1721 January 2023

           A YANG Data Model for IP Traffic Flow Security

Abstract

 This document describes a YANG module for the management of IP
 Traffic Flow Security (IP-TFS) additions to Internet Key Exchange
 Protocol version 2 (IKEv2) and IPsec.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 https://www.rfc-editor.org/info/rfc9348.

Copyright Notice

 Copyright (c) 2023 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (https://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Revised BSD License text as described in Section 4.e of the
 Trust Legal Provisions and are provided without warranty as described
 in the Revised BSD License.

Table of Contents

 1.  Introduction
 2.  Overview
 3.  YANG Management
   3.1.  YANG Tree
   3.2.  YANG Module
 4.  IANA Considerations
   4.1.  Updates to the IETF XML Registry
   4.2.  Updates to the YANG Module Names Registry
 5.  Security Considerations
 6.  References
   6.1.  Normative References
   6.2.  Informative References
 Appendix A.  Examples
   A.1.  Example XML Configuration
   A.2.  Example XML Operational Data
   A.3.  Example JSON Configuration
   A.4.  Example JSON Operational Data
   A.5.  Example JSON Operational Statistics
 Acknowledgements
 Authors' Addresses

1. Introduction

 This document defines a YANG module [RFC7950] for the management of
 the IP Traffic Flow Security (IP-TFS) extensions defined in
 [RFC9347].  IP-TFS provides enhancements to an IPsec tunnel Security
 Association (SA) to provide improved traffic confidentiality.
 Traffic confidentiality reduces the ability of traffic analysis to
 determine identity and correlate observable traffic patterns.  IP-TFS
 offers efficiency when aggregating traffic in fixed-size IPsec tunnel
 packets.
 The YANG data model in this document conforms to the Network
 Management Datastore Architecture (NMDA) defined in [RFC8342].
 The published YANG modules for IPsec are defined in [RFC9061].  This
 document uses these models as a general IPsec model that is augmented
 for IP-TFS.  The models in [RFC9061] provide for both an IKE and an
 IKE-less model.

2. Overview

 This document defines configuration and operational parameters of IP
 Traffic Flow Security (IP-TFS).  IP-TFS, defined in [RFC9347],
 defines a security association for tunnel mode IPsec with
 characteristics that improve traffic confidentiality and reduce
 bandwidth efficiency loss.  These documents assume familiarity with
 the IPsec concepts described in [RFC4301].
 IP-TFS uses tunnel mode to improve confidentiality by hiding inner
 packet identifiable information, packet size, and packet timing.  IP-
 TFS provides a general capability allowing aggregation of multiple
 packets in uniform-size outer tunnel IPsec packets.  It maintains the
 outer packet size by utilizing combinations of aggregating, padding,
 and fragmenting inner packets to fill out the IPsec outer tunnel
 packet.  Padding is used to fill the packet when no data is available
 to send.
 This document specifies an extensible configuration model for IP-TFS.
 This version utilizes the capabilities of IP-TFS to configure fixed-
 size IP-TFS packets that are transmitted at a constant rate.  This
 model is structured to allow for different types of operation through
 future augmentation.
 The IP-TFS YANG module augments the IPsec YANG module from [RFC9061].
 IP-TFS makes use of IPsec tunnel mode and adds a small number of
 configuration items to IPsec tunnel mode.  As defined in [RFC9347],
 any SA configured to use IP-TFS supports only IP-TFS packets, i.e.,
 no mixed IPsec modes.
 The behavior for IP-TFS is controlled by the source.  The self-
 describing format of an IP-TFS packet allows a sending side to adjust
 the packet size and timing independently from any receiver.  Both
 directions are also independent, e.g., IP-TFS may be run only in one
 direction.  This means that counters, which are created here for both
 directions, may be 0 or not updated in the case of an SA that uses
 IP-TFS only in on direction.
 Cases where IP-TFS statistics are active for one direction:
  • SA one direction - IP-TFS enabled
  • SA both directions - IP-TFS only enabled in one direction
 Case where IP-TFS statistics are active for both directions:
  • SA both directions - IP-TFS enable for both directions
 The IP-TFS model supports IP-TFS configuration and operational data.
 This YANG module supports configuration of fixed-size and fixed-rate
 packets, as well as elements that may be augmented to support future
 configuration.  The protocol specification [RFC9347] goes beyond this
 simple, fixed mode of operation by defining a general format for any
 type of scheme.  In this document, the outer IPsec packets can be
 sent with fixed or variable size (without padding).  The
 configuration allows the fixed packet size to be determined by the
 path MTU.  The fixed packet size can also be configured if a value
 lower than the path MTU is desired.
 Other configuration items include:
 Congestion Control:
    A congestion control setting to allow IP-TFS to reduce the packet
    rate when congestion is detected.
 Fixed-Rate Configuration:
    The IP-TFS tunnel rate can be configured by taking into account
    either layer 2 overhead or layer 3 overhead.  Layer 3 overhead is
    the IP data rate, and layer 2 overhead is the rate of bits on the
    link.  The combination of packet size and rate determines the
    nominal maximum bandwidth and the transmission interval when
    fixed-size packets are used.
 User Packet Fragmentation Control:
    While fragmentation is recommended for improved efficiency, a
    configuration is provided if users wish to observe the effect of
    no fragmentation on their data flows.
 The YANG operational data allows the readout of the configured
 parameters, as well as the per-SA statistics and error counters for
 IP-TFS.  Per-SA IPsec packet statistics are provided as a feature,
 and per-SA IP-TFS-specific statistics are provided as another
 feature.  Both sets of statistics augment the IPsec YANG modules with
 counters that allow observation of IP-TFS packet efficiency.
 IPsec YANG management objects are set in [RFC9061].  IP-TFS YANG
 augments the IKE and the IKE-less models.  In these models, the
 Security Policy database entry and Security Association entry for an
 IPsec tunnel can be augmented with IP-TFS.  In addition, this model
 uses YANG types defined in [RFC6991].

3. YANG Management

3.1. YANG Tree

 The following is the YANG tree diagram [RFC8340] for the IP-TFS
 extensions.
 module: ietf-ipsec-iptfs
   augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:spd
             /nsfike:spd-entry/nsfike:ipsec-policy-config
             /nsfike:processing-info/nsfike:ipsec-sa-cfg:
     +--rw traffic-flow-security
        +--rw congestion-control?           boolean
        +--rw packet-size
        |  +--rw use-path-mtu-discovery?   boolean
        |  +--rw outer-packet-size?        uint16
        +--rw (tunnel-rate)?
        |  +--:(l2-fixed-rate)
        |  |  +--rw l2-fixed-rate?          yang:gauge64
        |  +--:(l3-fixed-rate)
        |     +--rw l3-fixed-rate?          yang:gauge64
        +--rw dont-fragment?                boolean
        +--rw max-aggregation-time?         decimal64
        +--rw window-size?                  uint16
        +--rw send-immediately?             boolean
        +--rw lost-packet-timer-interval?   decimal64
   augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:child-sa-info:
     +--ro traffic-flow-security
        +--ro congestion-control?           boolean
        +--ro packet-size
        |  +--ro use-path-mtu-discovery?   boolean
        |  +--ro outer-packet-size?        uint16
        +--ro (tunnel-rate)?
        |  +--:(l2-fixed-rate)
        |  |  +--ro l2-fixed-rate?          yang:gauge64
        |  +--:(l3-fixed-rate)
        |     +--ro l3-fixed-rate?          yang:gauge64
        +--ro dont-fragment?                boolean
        +--ro max-aggregation-time?         decimal64
        +--ro window-size?                  uint16
        +--ro send-immediately?             boolean
        +--ro lost-packet-timer-interval?   decimal64
   augment /nsfikels:ipsec-ikeless/nsfikels:spd/nsfikels:spd-entry
             /nsfikels:ipsec-policy-config/nsfikels:processing-info
             /nsfikels:ipsec-sa-cfg:
     +--rw traffic-flow-security
        +--rw congestion-control?           boolean
        +--rw packet-size
        |  +--rw use-path-mtu-discovery?   boolean
        |  +--rw outer-packet-size?        uint16
        +--rw (tunnel-rate)?
        |  +--:(l2-fixed-rate)
        |  |  +--rw l2-fixed-rate?          yang:gauge64
        |  +--:(l3-fixed-rate)
        |     +--rw l3-fixed-rate?          yang:gauge64
        +--rw dont-fragment?                boolean
        +--rw max-aggregation-time?         decimal64
        +--rw window-size?                  uint16
        +--rw send-immediately?             boolean
        +--rw lost-packet-timer-interval?   decimal64
   augment /nsfikels:ipsec-ikeless/nsfikels:sad/nsfikels:sad-entry:
     +--ro traffic-flow-security
        +--ro congestion-control?           boolean
        +--ro packet-size
        |  +--ro use-path-mtu-discovery?   boolean
        |  +--ro outer-packet-size?        uint16
        +--ro (tunnel-rate)?
        |  +--:(l2-fixed-rate)
        |  |  +--ro l2-fixed-rate?          yang:gauge64
        |  +--:(l3-fixed-rate)
        |     +--ro l3-fixed-rate?          yang:gauge64
        +--ro dont-fragment?                boolean
        +--ro max-aggregation-time?         decimal64
        +--ro window-size?                  uint16
        +--ro send-immediately?             boolean
        +--ro lost-packet-timer-interval?   decimal64
   augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:child-sa-info:
     +--ro ipsec-stats {ipsec-stats}?
     |  +--ro tx-pkts?        yang:counter64
     |  +--ro tx-octets?      yang:counter64
     |  +--ro tx-drop-pkts?   yang:counter64
     |  +--ro rx-pkts?        yang:counter64
     |  +--ro rx-octets?      yang:counter64
     |  +--ro rx-drop-pkts?   yang:counter64
     +--ro iptfs-inner-pkt-stats {iptfs-stats}?
     |  +--ro tx-pkts?              yang:counter64
     |  +--ro tx-octets?            yang:counter64
     |  +--ro rx-pkts?              yang:counter64
     |  +--ro rx-octets?            yang:counter64
     |  +--ro rx-incomplete-pkts?   yang:counter64
     +--ro iptfs-outer-pkt-stats {iptfs-stats}?
        +--ro tx-all-pad-pkts?       yang:counter64
        +--ro tx-all-pad-octets?     yang:counter64
        +--ro tx-extra-pad-pkts?     yang:counter64
        +--ro tx-extra-pad-octets?   yang:counter64
        +--ro rx-all-pad-pkts?       yang:counter64
        +--ro rx-all-pad-octets?     yang:counter64
        +--ro rx-extra-pad-pkts?     yang:counter64
        +--ro rx-extra-pad-octets?   yang:counter64
        +--ro rx-errored-pkts?       yang:counter64
        +--ro rx-missed-pkts?        yang:counter64
   augment /nsfikels:ipsec-ikeless/nsfikels:sad/nsfikels:sad-entry:
     +--ro ipsec-stats {ipsec-stats}?
     |  +--ro tx-pkts?        yang:counter64
     |  +--ro tx-octets?      yang:counter64
     |  +--ro tx-drop-pkts?   yang:counter64
     |  +--ro rx-pkts?        yang:counter64
     |  +--ro rx-octets?      yang:counter64
     |  +--ro rx-drop-pkts?   yang:counter64
     +--ro iptfs-inner-pkt-stats {iptfs-stats}?
     |  +--ro tx-pkts?              yang:counter64
     |  +--ro tx-octets?            yang:counter64
     |  +--ro rx-pkts?              yang:counter64
     |  +--ro rx-octets?            yang:counter64
     |  +--ro rx-incomplete-pkts?   yang:counter64
     +--ro iptfs-outer-pkt-stats {iptfs-stats}?
        +--ro tx-all-pad-pkts?       yang:counter64
        +--ro tx-all-pad-octets?     yang:counter64
        +--ro tx-extra-pad-pkts?     yang:counter64
        +--ro tx-extra-pad-octets?   yang:counter64
        +--ro rx-all-pad-pkts?       yang:counter64
        +--ro rx-all-pad-octets?     yang:counter64
        +--ro rx-extra-pad-pkts?     yang:counter64
        +--ro rx-extra-pad-octets?   yang:counter64
        +--ro rx-errored-pkts?       yang:counter64
        +--ro rx-missed-pkts?        yang:counter64

3.2. YANG Module

 The following is the YANG module for managing the IP-TFS extensions.
 The model contains references to [RFC9347] and [RFC5348].
 <CODE BEGINS> file "ietf-ipsec-iptfs@2023-01-31.yang"
 module ietf-ipsec-iptfs {
   yang-version 1.1;
   namespace "urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs";
   prefix iptfs;
   import ietf-i2nsf-ike {
     prefix nsfike;
     reference
       "RFC 9061: A YANG Data Model for IPsec Flow Protection Based on
        Software-Defined Networking (SDN), Section 5.2";
   }
   import ietf-i2nsf-ikeless {
     prefix nsfikels;
     reference
       "RFC 9061: A YANG Data Model for IPsec Flow Protection Based on
        Software-Defined Networking (SDN), Section 5.3";
   }
   import ietf-yang-types {
     prefix yang;
     reference
       "RFC 6991: Common YANG Data Types";
   }
   organization
     "IETF IPSECME Working Group (IPSECME)";
   contact
     "WG Web:  <https://datatracker.ietf.org/wg/ipsecme/>
      WG List: <mailto:ipsecme@ietf.org>
      Author: Don Fedyk
              <mailto:dfedyk@labn.net>
      Author: Christian Hopps
              <mailto:chopps@chopps.org>";
   description
     "This module defines the configuration and operational state for
      managing the IP Traffic Flow Security functionality (RFC 9348).
      Copyright (c) 2023 IETF Trust and the persons identified as
      authors of the code.  All rights reserved.
      Redistribution and use in source and binary forms, with or
      without modification, is permitted pursuant to, and subject
      to the license terms contained in, the Revised BSD License
      set forth in Section 4.c of the IETF Trust's Legal Provisions
      Relating to IETF Documents
      (https://trustee.ietf.org/license-info).
      This version of this YANG module is part of RFC 9348; see
      the RFC itself for full legal notices.";
   revision 2023-01-31 {
     description
       "Initial revision";
     reference
       "RFC 9348: A YANG Data Model for IP Traffic Flow Security";
   }
   feature ipsec-stats {
     description
       "This feature indicates the device supports
        per-SA IPsec statistics.";
   }
   feature iptfs-stats {
     description
       "This feature indicates the device supports
        per-SA IP Traffic Flow Security statistics.";
   }
   /*--------------------*/
   /*   groupings        */
   /*--------------------*/
   grouping ipsec-tx-stat-grouping {
     description
       "IPsec outbound statistics";
     leaf tx-pkts {
       type yang:counter64;
       config false;
       description
         "Outbound Packet count";
     }
     leaf tx-octets {
       type yang:counter64;
       config false;
       description
         "Outbound Packet bytes";
     }
     leaf tx-drop-pkts {
       type yang:counter64;
       config false;
       description
         "Outbound dropped packets count";
     }
   }
   grouping ipsec-rx-stat-grouping {
     description
       "IPsec inbound statistics";
     leaf rx-pkts {
       type yang:counter64;
       config false;
       description
         "Inbound Packet count";
     }
     leaf rx-octets {
       type yang:counter64;
       config false;
       description
         "Inbound Packet bytes";
     }
     leaf rx-drop-pkts {
       type yang:counter64;
       config false;
       description
         "Inbound dropped packets count";
     }
   }
   grouping iptfs-inner-tx-stat-grouping {
     description
       "IP-TFS outbound inner packet statistics";
     leaf tx-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS inner packets sent.  This
          count is whole packets only.  A fragmented packet
          counts as one packet.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS)";
     }
     leaf tx-octets {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS inner octets sent.  This is
          inner packet octets only. It does not count padding.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS)";
     }
   }
   grouping iptfs-outer-tx-stat-grouping {
     description
       "IP-TFS outbound inner packet statistics";
     leaf tx-all-pad-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of transmitted IP-TFS packets that
          were all padding with no inner packet data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3";
     }
     leaf tx-all-pad-octets {
       type yang:counter64;
       config false;
       description
         "Total number transmitted octets of padding added to
          IP-TFS packets with no inner packet data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3";
     }
     leaf tx-extra-pad-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of transmitted outer IP-TFS packets
          that included some padding.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
     }
     leaf tx-extra-pad-octets {
       type yang:counter64;
       config false;
       description
         "Total number of transmitted octets of padding added
          to outer IP-TFS packets with data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
     }
   }
   grouping iptfs-inner-rx-stat-grouping {
     description
       "IP-TFS inner packet inbound statistics";
     leaf rx-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS inner packets received.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2";
     }
     leaf rx-octets {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS inner octets received.  It does
          not include padding or overhead.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2";
     }
     leaf rx-incomplete-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS inner packets that were
          incomplete.  Usually this is due to fragments that are
          not received.  Also, this may be due to misordering or
          errors in received outer packets.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS)";
     }
   }
   grouping iptfs-outer-rx-stat-grouping {
     description
       "IP-TFS outer packet inbound statistics";
     leaf rx-all-pad-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of received IP-TFS packets that were
          all padding with no inner packet data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3";
     }
     leaf rx-all-pad-octets {
       type yang:counter64;
       config false;
       description
         "Total number of received octets of padding added to
          IP-TFS packets with no inner packet data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3";
     }
     leaf rx-extra-pad-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of received outer IP-TFS packets that
          included some padding.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
     }
     leaf rx-extra-pad-octets {
       type yang:counter64;
       config false;
       description
         "Total number of received octets of padding added to
          outer IP-TFS packets with data.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
     }
     leaf rx-errored-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS outer packets dropped due to
          errors.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS)";
     }
     leaf rx-missed-pkts {
       type yang:counter64;
       config false;
       description
         "Total number of IP-TFS outer packets missing,
          indicated by a missing sequence number.";
       reference
         "RFC 9347: Aggregation and Fragmentation Mode for
          Encapsulating Security Payload (ESP) and Its Use for
          IP Traffic Flow Security (IP-TFS)";
     }
   }
   grouping iptfs-config {
     description
       "This is the grouping for IP-TFS configuration.";
     container traffic-flow-security {
       description
         "Configure the IPsec TFS in the Security
          Association Database (SAD).";
       leaf congestion-control {
         type boolean;
         default "true";
         description
           "When set to true, the default, this enables the
            congestion control on-the-wire exchange of data that is
            required by congestion control algorithms, as defined by
            RFC 5348.  When set to false, IP-TFS sends fixed-size
            packets over an IP-TFS tunnel at a constant rate.";
         reference
           "RFC 9347: Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for
            IP Traffic Flow Security (IP-TFS), Section 2.4.2;
            RFC 5348: TCP Friendly Rate Control (TFRC): Protocol
            Specification";
       }
       container packet-size {
         description
           "Packet size is either auto-discovered or manually
            configured.";
         leaf use-path-mtu-discovery {
           type boolean;
           default "true";
           description
             "Utilize path MTU discovery to determine maximum
              IP-TFS packet size.  If the packet size is explicitly
              configured, then it will only be adjusted downward if
              use-path-mtu-discovery is set.";
           reference
             "RFC 9347: Aggregation and Fragmentation Mode for
              Encapsulating Security Payload (ESP) and Its Use for
              IP Traffic Flow Security (IP-TFS), Section 4.2";
         }
         leaf outer-packet-size {
           type uint16;
           units "bytes";
           description
             "On transmission, the size of the outer encapsulating
              tunnel packet (i.e., the IP packet containing
              Encapsulating Security Payload (ESP)).";
           reference
             "RFC 9347: Aggregation and Fragmentation Mode for
              Encapsulating Security Payload (ESP) and Its Use for
              IP Traffic Flow Security (IP-TFS), Section 4.2";
         }
       }
       choice tunnel-rate {
         description
           "The TFS bit rate may be specified at layer 2 wire
            rate or layer 3 packet rate.";
         leaf l2-fixed-rate {
           type yang:gauge64;
           units "bits/second";
           description
             "On transmission, target bandwidth/bit rate in
              bits/second for IP-TFS tunnel.  This fixed rate is the
              nominal timing for the fixed-size packet.  If
              congestion control is enabled, the rate may be
              adjusted down (or up if unset).";
           reference
             "RFC 9347: Aggregation and Fragmentation Mode for
              Encapsulating Security Payload (ESP) and Its Use for
              IP Traffic Flow Security (IP-TFS), Section 4.1";
         }
         leaf l3-fixed-rate {
           type yang:gauge64;
           units "bits/second";
           description
             "On transmission, target bandwidth/bit rate in
              bits/second for IP-TFS tunnel.  This fixed rate is the
              nominal timing for the fixed-size packet.  If
              congestion control is enabled, the rate may be
              adjusted down (or up if unset).";
           reference
             "RFC 9347: Aggregation and Fragmentation Mode for
              Encapsulating Security Payload (ESP) and Its Use for
              IP Traffic Flow Security (IP-TFS), Section 4.1";
         }
       }
       leaf dont-fragment {
         type boolean;
         default "false";
         description
           "On transmission, disable packet fragmentation across
            consecutive IP-TFS tunnel packets; inner packets larger
            than what can be transmitted in outer packets will be
            dropped.";
         reference
           "RFC 9347: Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for
            IP Traffic Flow Security (IP-TFS), Section 2.2.4 and
            6.1.4";
       }
       leaf max-aggregation-time {
         type decimal64 {
           fraction-digits 6;
         }
         units "milliseconds";
         description
           "On transmission, maximum aggregation time is the
            maximum length of time a received inner packet can be
            held prior to transmission in the IP-TFS tunnel.  Inner
            packets that would be held longer than this time, based
            on the current tunnel configuration, will be dropped
            rather than be queued for transmission.  Maximum
            aggregation time is configurable in milliseconds or
            fractional milliseconds down to 1 nanosecond.";
       }
       leaf window-size {
         type uint16 {
           range "0..65535";
         }
         description
           "On reception, the maximum number of out-of-order
            packets that will be reordered by an IP-TFS receiver
            while performing the reordering operation.  The value 0
            disables any reordering.";
         reference
           "RFC 9347: Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for
            IP Traffic Flow Security (IP-TFS), Section 2.2.3";
       }
       leaf send-immediately {
         type boolean;
         default "false";
         description
           "On reception, send inner packets as soon as possible; do
            not wait for lost or misordered outer packets.
            Selecting this option reduces the inner (user) packet
            delay but can amplify out-of-order delivery of the
            inner packet stream in the presence of packet
            aggregation and any reordering.";
         reference
           "RFC 9347: Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for
            IP Traffic Flow Security (IP-TFS), Section 2.5";
       }
       leaf lost-packet-timer-interval {
         type decimal64 {
           fraction-digits 6;
         }
         units "milliseconds";
         description
           "On reception, this interval defines the length of time
            an IP-TFS receiver will wait for a missing packet before
            considering it lost.  If not using send-immediately,
            then each lost packet will delay inner (user) packets
            until this timer expires.  Setting this value too low
            can impact reordering and reassembly.  The value is
            configurable in milliseconds or fractional milliseconds
            down to 1 nanosecond.";
         reference
           "RFC 9347: Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for
            IP Traffic Flow Security (IP-TFS), Section 2.2.3";
       }
     }
   }
   /*
    * IP-TFS ike configuration
    */
   augment "/nsfike:ipsec-ike/nsfike:conn-entry/nsfike:spd/"
         + "nsfike:spd-entry/"
         + "nsfike:ipsec-policy-config/"
         + "nsfike:processing-info/"
         + "nsfike:ipsec-sa-cfg" {
     description
       "IP-TFS configuration for this policy.";
     uses iptfs-config;
   }
   augment "/nsfike:ipsec-ike/nsfike:conn-entry/"
         + "nsfike:child-sa-info" {
     description
       "IP-TFS configured on this SA.";
     uses iptfs-config {
       refine "traffic-flow-security" {
         config false;
       }
     }
   }
   /*
    * IP-TFS ikeless configuration
    */
   augment "/nsfikels:ipsec-ikeless/nsfikels:spd/"
         + "nsfikels:spd-entry/"
         + "nsfikels:ipsec-policy-config/"
         + "nsfikels:processing-info/"
         + "nsfikels:ipsec-sa-cfg" {
     description
       "IP-TFS configuration for this policy.";
     uses iptfs-config;
   }
   augment "/nsfikels:ipsec-ikeless/nsfikels:sad/"
         + "nsfikels:sad-entry" {
     description
       "IP-TFS configured on this SA.";
     uses iptfs-config {
       refine "traffic-flow-security" {
         config false;
       }
     }
   }
   /*
    * packet counters
    */
   augment "/nsfike:ipsec-ike/nsfike:conn-entry/"
         + "nsfike:child-sa-info" {
     description
       "Per-SA counters";
     container ipsec-stats {
       if-feature "ipsec-stats";
       config false;
       description
         "IPsec per-SA packet counters.
          tx = outbound, rx = inbound";
       uses ipsec-tx-stat-grouping;
       uses ipsec-rx-stat-grouping;
     }
     container iptfs-inner-pkt-stats {
       if-feature "iptfs-stats";
       config false;
       description
         "IP-TFS per-SA inner packet counters.
          tx = outbound, rx = inbound";
       uses iptfs-inner-tx-stat-grouping;
       uses iptfs-inner-rx-stat-grouping;
     }
     container iptfs-outer-pkt-stats {
       if-feature "iptfs-stats";
       config false;
       description
         "IP-TFS per-SA outer packets counters.
          tx = outbound, rx = inbound";
       uses iptfs-outer-tx-stat-grouping;
       uses iptfs-outer-rx-stat-grouping;
     }
   }
   /*
    * packet counters
    */
   augment "/nsfikels:ipsec-ikeless/nsfikels:sad/"
         + "nsfikels:sad-entry" {
     description
       "Per-SA counters";
     container ipsec-stats {
       if-feature "ipsec-stats";
       config false;
       description
         "IPsec per-SA packet counters.
          tx = outbound, rx = inbound";
       uses ipsec-tx-stat-grouping;
       uses ipsec-rx-stat-grouping;
     }
     container iptfs-inner-pkt-stats {
       if-feature "iptfs-stats";
       config false;
       description
         "IP-TFS per-SA inner packet counters.
          tx = outbound, rx = inbound";
       uses iptfs-inner-tx-stat-grouping;
       uses iptfs-inner-rx-stat-grouping;
     }
     container iptfs-outer-pkt-stats {
       if-feature "iptfs-stats";
       config false;
       description
         "IP-TFS per-SA outer packets counters.
          tx = outbound, rx = inbound";
       uses iptfs-outer-tx-stat-grouping;
       uses iptfs-outer-rx-stat-grouping;
     }
   }
 }
 <CODE ENDS>

4. IANA Considerations

4.1. Updates to the IETF XML Registry

 Per this document, IANA has registered a URI in the "IETF XML
 Registry" [RFC3688] as follows.
 URI:  urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs
 Registrant Contact:  The IESG.
 XML:  N/A; the requested URI is an XML namespace.

4.2. Updates to the YANG Module Names Registry

 Per this document, IANA has registered one YANG module in the "YANG
 Module Names" registry [RFC6020] as follows.
 Name:  ietf-ipsec-iptfs
 Namespace:  urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs
 Prefix:  iptfs
 Reference:  RFC 9348

5. Security Considerations

 The YANG module specified in this document defines a schema for data
 that is designed to be accessed via network management protocols such
 as NETCONF [RFC6241] or RESTCONF [RFC8040].  The lowest NETCONF layer
 is the secure transport layer, and the mandatory-to-implement secure
 transport is Secure Shell (SSH) [RFC6242].  The lowest RESTCONF layer
 is HTTPS, and the mandatory-to-implement secure transport is TLS
 [RFC8446].
 The Network Configuration Access Control Model (NACM) [RFC8341]
 provides the means to restrict access for particular NETCONF or
 RESTCONF users to a preconfigured subset of all available NETCONF or
 RESTCONF protocol operations and content.
 There are a number of data nodes defined in this YANG module that are
 writable/creatable/deletable (i.e., config true, which is the
 default).  These data nodes may be considered sensitive or vulnerable
 in some network environments.  Write operations (e.g., edit-config)
 to these data nodes without proper protection can have a negative
 effect on network operations.  These are the subtrees and data nodes
 and their sensitivity/vulnerability:
 ../traffic-flow-security:  Enabling IP-TFS is controlled by setting
    the entries under traffic-flow-security in IKE or IKE-less models.
    IP-TFS is set either to be congestion sensitive or a fixed rate by
    setting parameters in this subtree.
 Some of the readable data nodes in this YANG module may be considered
 sensitive or vulnerable in some network environments.  It is thus
 important to control read access (e.g., via get, get-config, or
 notification) to these data nodes.  These are the subtrees and data
 nodes and their sensitivity/vulnerability:
 ../iptfs-inner-pkt-stats and ../iptfs-outer-pkt-stats:  Access to IP-
    TFS statistics can provide information that IP-TFS obscures, such
    as the true activity of the flows using IP-TFS.

6. References

6.1. Normative References

 [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
            Internet Protocol", RFC 4301, DOI 10.17487/RFC4301,
            December 2005, <https://www.rfc-editor.org/info/rfc4301>.
 [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
            the Network Configuration Protocol (NETCONF)", RFC 6020,
            DOI 10.17487/RFC6020, October 2010,
            <https://www.rfc-editor.org/info/rfc6020>.
 [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
            and A. Bierman, Ed., "Network Configuration Protocol
            (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
            <https://www.rfc-editor.org/info/rfc6241>.
 [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
            Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
            <https://www.rfc-editor.org/info/rfc6242>.
 [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
            RFC 6991, DOI 10.17487/RFC6991, July 2013,
            <https://www.rfc-editor.org/info/rfc6991>.
 [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
            RFC 7950, DOI 10.17487/RFC7950, August 2016,
            <https://www.rfc-editor.org/info/rfc7950>.
 [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
            Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
            <https://www.rfc-editor.org/info/rfc8040>.
 [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
            Access Control Model", STD 91, RFC 8341,
            DOI 10.17487/RFC8341, March 2018,
            <https://www.rfc-editor.org/info/rfc8341>.
 [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
            and R. Wilton, "Network Management Datastore Architecture
            (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
            <https://www.rfc-editor.org/info/rfc8342>.
 [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
            Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
            <https://www.rfc-editor.org/info/rfc8446>.
 [RFC9061]  Marin-Lopez, R., Lopez-Millan, G., and F. Pereniguez-
            Garcia, "A YANG Data Model for IPsec Flow Protection Based
            on Software-Defined Networking (SDN)", RFC 9061,
            DOI 10.17487/RFC9061, July 2021,
            <https://www.rfc-editor.org/info/rfc9061>.
 [RFC9347]  Hopps, C., "Aggregation and Fragmentation Mode for
            Encapsulating Security Payload (ESP) and Its Use for IP
            Traffic Flow Security (IP-TFS)", RFC 9347,
            DOI 10.17487/RFC9347, January 2023,
            <https://www.rfc-editor.org/info/rfc9347>.

6.2. Informative References

 [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
            DOI 10.17487/RFC3688, January 2004,
            <https://www.rfc-editor.org/info/rfc3688>.
 [RFC5348]  Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP
            Friendly Rate Control (TFRC): Protocol Specification",
            RFC 5348, DOI 10.17487/RFC5348, September 2008,
            <https://www.rfc-editor.org/info/rfc5348>.
 [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
            BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
            <https://www.rfc-editor.org/info/rfc8340>.

Appendix A. Examples

 The following examples show configuration and operational data for
 the IKE-less and IKE cases using XML and JSON.  Also, the operational
 statistics for the IKE-less case is illustrated.

A.1. Example XML Configuration

 This example illustrates configuration for IP-TFS in the IKE-less
 case.  Note that, since this augments the IPsec IKE-less schema, only
 a minimal IKE-less configuration to satisfy the schema has been
 populated.
 <i:ipsec-ikeless
   xmlns:i="urn:ietf:params:xml:ns:yang:ietf-i2nsf-ikeless"
   xmlns:tfs="urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs">
   <i:spd>
     <i:spd-entry>
       <i:name>protect-policy-1</i:name>
       <i:direction>outbound</i:direction>
       <i:ipsec-policy-config>
         <i:traffic-selector>
           <i:local-prefix>192.0.2.0/16</i:local-prefix>
           <i:remote-prefix>198.51.100.0/16</i:remote-prefix>
         </i:traffic-selector>
         <i:processing-info>
           <i:action>protect</i:action>
           <i:ipsec-sa-cfg>
             <tfs:traffic-flow-security>
              <tfs:congestion-control>true</tfs:congestion-control>
               <tfs:packet-size>
                 <tfs:use-path-mtu-discovery
                    >true</tfs:use-path-mtu-discovery>
               </tfs:packet-size>
               <tfs:l2-fixed-rate>1000000000</tfs:l2-fixed-rate>
               <tfs:max-aggregation-time
                  >0.1</tfs:max-aggregation-time>
               <tfs:window-size>5</tfs:window-size>
               <tfs:send-immediately>false</tfs:send-immediately>
               <tfs:lost-packet-timer-interval
                  >0.2</tfs:lost-packet-timer-interval>
             </tfs:traffic-flow-security>
           </i:ipsec-sa-cfg>
         </i:processing-info>
       </i:ipsec-policy-config>
     </i:spd-entry>
   </i:spd>
 </i:ipsec-ikeless>
               Figure 1: Example IP-TFS XML Configuration

A.2. Example XML Operational Data

 This example illustrates operational data for IP-TFS in the IKE-less
 case.  Note that, since this augments the IPsec IKE-less schema only,
 a minimal IKE-less configuration to satisfy the schema has been
 populated.
 <i:ipsec-ikeless
   xmlns:i="urn:ietf:params:xml:ns:yang:ietf-i2nsf-ikeless"
   xmlns:tfs="urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs">
   <i:sad>
     <i:sad-entry>
       <i:name>sad-1</i:name>
       <i:ipsec-sa-config>
         <i:spi>1</i:spi>
         <i:traffic-selector>
           <i:local-prefix>2001:db8:1::/48</i:local-prefix>
           <i:remote-prefix>2001:db8:2::/48</i:remote-prefix>
         </i:traffic-selector>
       </i:ipsec-sa-config>
       <tfs:traffic-flow-security>
         <tfs:congestion-control>true</tfs:congestion-control>
         <tfs:packet-size>
           <tfs:use-path-mtu-discovery
             >true</tfs:use-path-mtu-discovery>
         </tfs:packet-size>
         <tfs:l2-fixed-rate>1000000000</tfs:l2-fixed-rate>
         <tfs:max-aggregation-time>0.100</tfs:max-aggregation-time>
         <tfs:window-size>0</tfs:window-size>
         <tfs:send-immediately>true</tfs:send-immediately>
         <tfs:lost-packet-timer-interval
           >0.200</tfs:lost-packet-timer-interval>
       </tfs:traffic-flow-security>
     </i:sad-entry>
   </i:sad>
 </i:ipsec-ikeless>
             Figure 2: Example IP-TFS XML Operational Data

A.3. Example JSON Configuration

 This example illustrates configuration data for IP-TFS in the IKE
 case.  Note that, since this augments the IPsec IKE schema, only a
 minimal IKE configuration to satisfy the schema has been populated.
 {
   "ietf-i2nsf-ike:ipsec-ike": {
     "ietf-i2nsf-ike:conn-entry": [
       {
         "name": "my-peer-connection",
         "ike-sa-encr-alg": [
           {
             "id": 1,
             "algorithm-type": 12,
             "key-length": 128
           }
           ],
           "local": {
             "local-pad-entry-name": "local-1"
           },
           "remote": {
             "remote-pad-entry-name": "remote-1"
           },
           "ietf-i2nsf-ike:spd": {
           "spd-entry": [
             {
               "name": "protect-policy-1",
               "ipsec-policy-config": {
                 "traffic-selector": {
                   "local-prefix": "192.0.2.0/16",
                   "remote-prefix": "198.51.100.0/16"
                 },
                 "processing-info": {
                   "action": "protect",
                   "ipsec-sa-cfg": {
                     "ietf-ipsec-iptfs:traffic-flow-security": {
                       "congestion-control": true,
                       "l2-fixed-rate": "1000000000",
                       "packet-size": {
                         "use-path-mtu-discovery": true
                       },
                       "max-aggregation-time": "0.1",
                       "window-size": 1,
                       "send-immediately": false,
                       "lost-packet-timer-interval": "0.2"
                     }
                   }
                 }
               }
             }
           ]
         }
       }
     ]
   }
 }
              Figure 3: Example IP-TFS JSON Configuration

A.4. Example JSON Operational Data

 This example illustrates operational data for IP-TFS in the IKE case.
 Note that, since this augments the IPsec IKE tree, only a minimal IKE
 configuration to satisfy the schema has been populated.
 {
   "ietf-i2nsf-ike:ipsec-ike": {
     "ietf-i2nsf-ike:conn-entry": [
       {
         "name": "my-peer-connection",
         "ike-sa-encr-alg": [
         {
           "id": 1,
           "algorithm-type": 12,
           "key-length": 128
         }
         ],
         "local": {
           "local-pad-entry-name": "local-1"
         },
         "remote": {
           "remote-pad-entry-name": "remote-1"
         },
         "ietf-i2nsf-ike:child-sa-info": {
           "ietf-ipsec-iptfs:traffic-flow-security": {
             "congestion-control": true,
             "l2-fixed-rate": "1000000000",
             "packet-size": {
               "use-path-mtu-discovery": true
             },
             "max-aggregation-time": "0.1",
             "window-size": 5,
             "send-immediately": false,
             "lost-packet-timer-interval": "0.2"
           }
         }
       }
     ]
   }
 }
             Figure 4: Example IP-TFS JSON Operational Data

A.5. Example JSON Operational Statistics

 This example shows the JSON formatted statistics for IP-TFS.  Note a
 unidirectional IP-TFS transmit side is illustrated, with arbitrary
 numbers for transmit.
 {
   "ietf-i2nsf-ikeless:ipsec-ikeless": {
     "sad": {
       "sad-entry": [
         {
           "name": "sad-1",
           "ipsec-sa-config": {
             "spi": 1,
             "traffic-selector": {
               "local-prefix": "192.0.2.1/16",
               "remote-prefix": "198.51.100.0/16"
             }
           },
           "ietf-ipsec-iptfs:traffic-flow-security": {
             "window-size": 5,
             "send-immediately": false,
             "lost-packet-timer-interval": "0.2"
           },
           "ietf-ipsec-iptfs:ipsec-stats": {
             "tx-pkts": "300",
             "tx-octets": "80000",
             "tx-drop-pkts": "2",
             "rx-pkts": "0",
             "rx-octets": "0",
             "rx-drop-pkts": "0"
           },
           "ietf-ipsec-iptfs:iptfs-inner-pkt-stats": {
             "tx-pkts": "250",
             "tx-octets": "75000",
             "rx-pkts": "0",
             "rx-octets": "0",
             "rx-incomplete-pkts": "0"
           },
           "ietf-ipsec-iptfs:iptfs-outer-pkt-stats": {
             "tx-all-pad-pkts": "40",
             "tx-all-pad-octets": "40000",
             "tx-extra-pad-pkts": "200",
             "tx-extra-pad-octets": "30000",
             "rx-all-pad-pkts": "0",
             "rx-all-pad-octets": "0",
             "rx-extra-pad-pkts": "0",
             "rx-extra-pad-octets": "0",
             "rx-errored-pkts": "0",
             "rx-missed-pkts": "0"
           },
           "ipsec-sa-state": {
             "sa-lifetime-current": {
               "time": 80000,
               "bytes": "400606",
               "packets": 1000,
               "idle": 5
             }
           }
         }
       ]
     }
   }
 }
                Figure 5: Example IP-TFS JSON Statistics

Acknowledgements

 The authors would like to thank Eric Kinzie, Jürgen Schönwälder, Lou
 Berger, and Tero Kivinen for their feedback and review on the YANG
 module.

Authors' Addresses

 Don Fedyk
 LabN Consulting, L.L.C.
 Email: dfedyk@labn.net
 Christian Hopps
 LabN Consulting, L.L.C.
 Email: chopps@chopps.org
/home/gen.uk/domains/wiki.gen.uk/public_html/data/pages/rfc/rfc9348.txt · Last modified: 2023/02/01 05:18 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki