GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc8556

Internet Engineering Task Force (IETF) E. Rosen, Ed. Request for Comments: 8556 M. Sivakumar Category: Standards Track T. Przygienda ISSN: 2070-1721 Juniper Networks, Inc.

                                                             S. Aldrin
                                                          Google, Inc.
                                                           A. Dolganow
                                                                 Nokia
                                                            April 2018
     Multicast VPN Using Bit Index Explicit Replication (BIER)

Abstract

 The Multicast Virtual Private Network (MVPN) specifications require
 the use of multicast tunnels ("P-tunnels") that traverse a service
 provider's backbone network.  The P-tunnels are used for carrying
 multicast traffic across the backbone.  A variety of P-tunnel types
 are supported.  Bit Index Explicit Replication (BIER) is a new
 architecture that provides optimal multicast forwarding through a
 "multicast domain", without requiring intermediate routers to
 maintain any per-flow state or to engage in an explicit tree-building
 protocol.  This document specifies the protocol and procedures that
 allow MVPN to use BIER as the method of carrying multicast traffic
 over a service provider's backbone network.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 https://www.rfc-editor.org/info/rfc8556.

Rosen, et al. Standards Track [Page 1] RFC 8556 MVPN with BIER April 2018

Copyright Notice

 Copyright (c) 2018 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (https://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Table of Contents

 1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
 2.  Use of the PMSI Tunnel Attribute in x-PMSI A-D Routes . . . .   5
   2.1.  MPLS Label  . . . . . . . . . . . . . . . . . . . . . . .   7
   2.2.  Explicit Tracking . . . . . . . . . . . . . . . . . . . .   9
     2.2.1.  Using the LIR Flag  . . . . . . . . . . . . . . . . .  10
     2.2.2.  Using the LIR-pF Flag . . . . . . . . . . . . . . . .  10
 3.  Use of the PMSI Tunnel Attribute in Leaf A-D Routes . . . . .  11
 4.  Data Plane  . . . . . . . . . . . . . . . . . . . . . . . . .  12
   4.1.  Encapsulation and Transmission  . . . . . . . . . . . . .  12
   4.2.  Disposition . . . . . . . . . . . . . . . . . . . . . . .  14
     4.2.1.  At a BFER That Is an Egress PE  . . . . . . . . . . .  14
     4.2.2.  At a BFER That Is a P-tunnel Segmentation Boundary  .  14
 5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  15
 6.  Security Considerations . . . . . . . . . . . . . . . . . . .  15
 7.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  15
   7.1.  Normative References  . . . . . . . . . . . . . . . . . .  15
   7.2.  Informative References  . . . . . . . . . . . . . . . . .  16
 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  16
 Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  16
 Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  17

Rosen, et al. Standards Track [Page 2] RFC 8556 MVPN with BIER April 2018

1. Introduction

 [RFC6513] and [RFC6514] specify the protocols and procedures that a
 Service Provider (SP) can use to provide Multicast Virtual Private
 Network (MVPN) service to its customers.  Multicast tunnels are
 created through an SP's backbone network; these are known as
 "P-tunnels".  The P-tunnels are used for carrying multicast traffic
 across the backbone.  The MVPN specifications allow the use of
 several different kinds of P-tunnel technology.
 Bit Index Explicit Replication (BIER) ([RFC8279]) is an architecture
 that provides optimal multicast forwarding through a "multicast
 domain", without requiring intermediate routers to maintain any per-
 flow state or to engage in an explicit tree-building protocol.  The
 purpose of the current document is to specify the protocols and
 procedures needed in order to provide MVPN service using BIER to
 transport the multicast traffic over the backbone.
 Although BIER does not explicitly build and maintain multicast
 tunnels, one can think of BIER as using a number of implicitly
 created tunnels through a "BIER domain".  In particular, one can
 think of there as being one Point-to-Multipoint (P2MP) tunnel from
 each Bit Forwarding Ingress Router (BFIR) to all the Bit Forwarding
 Egress Routers (BFERs) in the BIER domain, where a BIER domain is
 generally co-extensive with an IGP network.  These "tunnels" are not
 specific to any particular VPN.  However, the MVPN architecture
 provides protocols and procedures that allow the traffic of multiple
 MVPNs to be aggregated on a single P-tunnel.  In this document, we
 specify how to use these multi-VPN aggregation procedures to enable
 BIER to transport traffic from multiple MVPNs.
 MVPN traffic must sometimes traverse more than one IGP domain,
 whereas BIER only carries multicast traffic within a single IGP
 domain.  However, the MVPN specifications allow P-tunnels to be
 segmented (the concept of MVPN segmentation is defined in [RFC6513]
 and [RFC6514]), where the segmentation points may either be
 Autonomous System Border Routers (ASBRs) as described in [RFC6514],
 or Area Border Routers (ABRs) as described in [RFC7524].  As long as
 the segmentation points are capable of acting as BFIRs and BFERs,
 BIER can be used to provide some or all of the segments of a
 P-tunnel.
 Procedures to support MVPN customers who are using Bidirectional PIM
 (BIDIR-PIM) are outside the scope of this document.

Rosen, et al. Standards Track [Page 3] RFC 8556 MVPN with BIER April 2018

 This document uses the following terminology from [RFC8279]:
 o  BFR: Bit-Forwarding Router.
 o  BFIR: Bit-Forwarding Ingress Router.
 o  BFER: Bit-Forwarding Egress Router.
 This document uses the following terminology from [RFC6513]:
 o  MVPN: Multicast Virtual Private Network -- a VPN [RFC4364] in
    which multicast service is offered.
 o  P-tunnel: A multicast tunnel through the network of one or more
    SPs.  P-tunnels are used to transport MVPN multicast data
 o  PMSI: Provider Multicast Service Interface.  PMSI is an
    abstraction that represents a multicast service for carrying
    packets.  A PMSI is instantiated via one or more P-tunnels.
 o  C-S: A multicast source address, identifying a multicast source
    located at a VPN customer site.
 o  C-G: A multicast group address used by a VPN customer.
 o  C-flow: A customer multicast flow.  Each C-flow is identified by
    the ordered pair (source address, group address), where each
    address is in the customer's address space.  The identifier of a
    particular C-flow is usually written as (C-S,C-G).
    Sets of C-flows can be identified by the use of the "C-*" wildcard
    (see [RFC6625]), e.g., (C-*,C-G).
 o  I-PMSI A-D Route: Inclusive PMSI Auto-Discovery route.  Carried in
    BGP Update messages, these routes are used to advertise the
    default P-tunnel for a particular MVPN.
 o  S-PMSI A-D route: Selective PMSI Auto-Discovery route.  Carried in
    BGP Update messages, these routes are used to advertise the fact
    that particular C-flows are bound to (i.e., are traveling through)
    particular P-tunnels.
 o  x-PMSI A-D route: A route that is either an I-PMSI A-D route or an
    S-PMSI A-D route.
 o  Leaf A-D route: A route that a multicast egress node sends in
    order to join a particular P-tunnel.

Rosen, et al. Standards Track [Page 4] RFC 8556 MVPN with BIER April 2018

 o  PMSI Tunnel attribute (PTA): In an x-PMSI A-D route, the Network
    Layer Reachability Information (NLRI) of the route identifies a
    PMSI.  The BGP attribute known as the PMSI Tunnel attribute is
    attached to such a route in order to identify a particular
    P-tunnel that is associated with the PMSI.  When C-flows of
    multiple VPNs are carried in a single P-tunnel, this attribute
    also carries the information needed to multiplex and demultiplex
    the C-flows.  A PTA can also be carried by a Leaf A-D root.  In
    this case, it contains information that is needed in order for the
    originator of the route to join the specified P-tunnel.
 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
 "OPTIONAL" in this document are to be interpreted as described in
 BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
 capitals, as shown here.

2. Use of the PMSI Tunnel Attribute in x-PMSI A-D Routes

 As defined in [RFC6514], the PMSI Tunnel attribute (PTA) carried by
 an x-PMSI A-D route identifies the P-tunnel that is used to
 instantiate a particular PMSI.  If a PMSI is to be instantiated by
 BIER, the PTA is constructed by a BFIR.
 If segmented P-tunnels are not being used, the PTA attached to a
 given x-PMSI A-D route is constructed by the router that originated
 the route (typically by the ingress Provider Edge (PE) router), and
 the PTA is not changed as the route is propagated.
 If segmented P-tunnels are being used, the PTA attached to a given
 x-PMSI A-D route by the route's originator may be replaced at a
 segmentation point (a BFER) by a PTA identifying the next segment of
 the P-tunnel.  If the next segment of the P-tunnel is instantiated by
 BIER, the segmentation point serves as the BFIR for that next
 segment.
 In either case, a PTA is constructed by a BFIR as follows (see
 Figure 1):
 The PTA contains the following fields:
 o  Tunnel Type: IANA has assigned 0x0B as the tunnel type codepoint
    for "BIER" in the "P-Multicast Service Interface Tunnel (PMSI
    Tunnel) Tunnel Types" registry.  This codepoint is used to
    indicate that the PMSI is instantiated by BIER.
    Although BIER does not actually create tunnels, the MVPN
    procedures treat BIER as if it were a type of tunnel.

Rosen, et al. Standards Track [Page 5] RFC 8556 MVPN with BIER April 2018

 o  Tunnel Identifier: When the tunnel type is BIER, this field
    contains three subfields:
    1.  The first subfield is a single octet, containing a BIER
        sub-domain-id (see [RFC8279]).  This indicates that packets
        sent on the PMSI will be sent on the specified BIER
        sub-domain.  How that sub-domain is chosen is outside the
        scope of this document.
    2.  The second subfield is a two-octet field containing the BFR-id
        in the sub-domain identified in the first subfield of the
        router that is constructing the PTA.
    3.  The third subfield is the BFR-prefix (see [RFC8279]) of the
        router (a BFIR) that is constructing the PTA.  The BFR-prefix
        will either be a /32 IPv4 address or a /128 IPv6 address.
        Whether the address is IPv4 or IPv6 can be inferred from the
        total length of the PTA.
        The BFR-prefix need not be the same IP address that is carried
        in any other field of the x-PMSI A-D route, even if the BFIR
        is the originating router of the x-PMSI A-D route.
    Failure to properly set the Tunnel Identifier field cannot be
    detected by the protocol and will result in improper delivery of
    the data packets sent on the PMSI.
 o  MPLS Label: This field MUST contain an upstream-assigned non-zero
    MPLS label.  It is assigned by the router (a BFIR) that constructs
    the PTA.  Constraints on the way in which a BFIR selects this
    label are discussed in Section 2.1.
    Failure to follow the constraints on label assignment cannot be
    detected by the protocol and may result in improper handling of
    data packets by the egress PE routers.
 o  Flags: When the tunnel type is BIER, two of the flags in the PTA
    Flags field are meaningful.  Details about the use of these flags
    can be found in Section 2.2.
  • Leaf Information Required per Flow (LIR-pF): This flag is

introduced in [RFC8534]. A BFIR SHOULD NOT set this flag

       UNLESS it knows that all the BFERs in the BIER domain (or at
       least all the BFERs to which it needs to transmit) support this
       flag.  (How this is known is outside the scope of this
       document.)  Procedures for the use of this flag are given in
       Section 2.2.2.  Support for this flag is OPTIONAL.

Rosen, et al. Standards Track [Page 6] RFC 8556 MVPN with BIER April 2018

  • Leaf Information Required (LIR): see Section 2.2.1.
        +---------------------------------+
        |  Flags (1 octet)                |
        +---------------------------------+
        |  Tunnel Type = 0x0B (1 octet)   |
        +---------------------------------+
        |  MPLS Label (3 octets)          |
        +---------------------------------+
        |  Sub-domain-id (1 octet)        |  <---
        +---------------------------------+     |
        |  BFR-id (2 octets)              |     |-- Tunnel
        +---------------------------------+     |   Identifier
        |  BFR-prefix (4 or 16 octets)    |  <---
        +---------------------------------+
               Figure 1: PMSI Tunnel Attribute for BIER
 If a PTA specifying tunnel type BIER is attached to an x-PMSI A-D
 route, the route MUST NOT be distributed beyond the boundaries of a
 BIER domain.  That is, any routers that receive the route must be in
 the same BIER domain as the originator of the route.  If the
 originator is in more than one BIER domain, the route must be
 distributed only within the BIER domain in which the BFR-prefix in
 the PTA uniquely identifies the originator.  As with all MVPN routes,
 distribution of these routes is controlled by the provisioning of
 Route Targets (RTs).  Thus, the requirement expressed in this
 paragraph is really a requirement on the way the Route Targets are
 provisioned.

2.1. MPLS Label

 The MPLS Label carried in the PTA is an upstream-assigned label.
 If two PTAs contain the same BFR-prefix in their respective Tunnel
 Identifier fields, then the labels carried in those PTAs MUST come
 from the same label space (see Section 7 of [RFC5331]).  An
 implementation may choose to use this fact when setting up the tables
 it uses to interpret the upstream-assigned labels.
 Suppose that a BFIR attaches a PTA to each of two x-PMSI A-D routes,
 and both PTAs specify a tunnel type of BIER.
 o  If the two routes do not carry the same set of RTs, then their
    respective PTAs MUST contain different MPLS label values.

Rosen, et al. Standards Track [Page 7] RFC 8556 MVPN with BIER April 2018

 o  If the two routes do not have the same Address Family Identifier
    (AFI) value, then their respective PTAs MUST contain different
    MPLS label values.  This ensures that when an egress PE receives a
    data packet with the given label, the egress PE can infer from the
    label whether the payload is an IPv4 packet or an IPv6 packet.
 o  If the BFIR is an ingress PE supporting MVPN extranet ([RFC7900])
    functionality, and if the two routes originate from different VPN
    Routing and Forwarding tables (VRFs) on this ingress PE, then the
    respective PTAs of the two routes MUST contain different MPLS
    label values.
 o  If the BFIR is an ingress PE supporting the "Extranet Separation"
    feature of MVPN extranet (see Section 7.3 of [RFC7900]), and if
    one of the routes carries the "Extranet Separation" extended
    community but the other does not, then the respective PTAs of the
    two routes MUST contain different MPLS label values.
 o  If segmented P-tunnels are being used, then the respective PTAs of
    the two routes MUST contain different MPLS label values whenever
    the respective NLRIs of the two routes are not identical.  The
    MPLS label can then be used at the next segmentation point to
    switch packets from one P-tunnel segment directly to the next,
    without requiring the segmentation points to contain any other
    multicast forwarding state.  This is explained further below; see
    also Section 4.
 When segmented P-tunnels are being used, a segmentation point, call
 it "B1", may receive an x-PMSI A-D route whose PTA specifies BIER
 from within a given BIER domain.  This means that BIER is being used
 for the previous segment of a segmented P-tunnel.  If the next
 segment is also of type BIER, B1 will be the BFIR for the next
 segment.  That is, B1 is a BFER of one BIER domain (corresponding to
 the previous segment) and a BFIR of another BIER domain
 (corresponding to the next segment).  B1 needs to replace the PTA of
 the x-PMSI A-D route with a new PTA, specifying its own BFR-prefix
 and specifying an upstream-assigned label assigned by B1 itself.
 Suppose that B1 has received two x-PMSI A-D routes, R1 and R2, where:
 o  R1 and R2 each have a PTA specifying BIER.
 o  R1's PTA specifies BFR-prefix B2 and Label L2.
 o  R2's PTA specifies BFR-prefix B3 and Label L3.

Rosen, et al. Standards Track [Page 8] RFC 8556 MVPN with BIER April 2018

 Suppose B1 decides to propagate both R1 and R2, replacing each PTA
 with a new PTA specifying BIER.  Suppose these new PTAs specify
 labels L4 and L5,respectively.  Then L4 and L5 MUST be different
 (upstream-assigned) label values, UNLESS both of the following
 conditions hold:
 o  R1 and R2 have the same value in the Originating Router field of
    their respective NLRIs, and
 o  B2 is equal to B3, and
 o  L2 is equal to L3.
 The segmentation point (B1, in this example) MUST also program its
 data plane appropriately.  For example, when:
 o  B1 receives a BIER packet for which it is a BFER, and
 o  the BIER header specifies the BFIR-id that corresponds to B2, and
 o  the BIER payload is an MPLS packet with upstream-assigned label,
    and
 o  the top label value is L2,
 then the data plane must be programmed to replace L2 with L4 and to
 re-encapsulate the packet in a BIER header with B1's BFR-id in the
 BFIR-id field.  The BitString of the new BIER header is determined by
 applying the procedures for MVPN explicit tracking (see Section 2.2)
 in the BIER domain of the next segment, i.e., in the BIER domain for
 which B1 is the BFIR).

2.2. Explicit Tracking

 When using BIER to transport an MVPN data packet through a BIER
 domain, an ingress PE functions as a BFIR (see [RFC8279]).  The BFIR
 must determine the set of BFERs to which the packet needs to be
 delivered.  This can be done in either of two ways:
 1.  Using the explicit tracking mechanism based on the "Leaf
     Information Required" flag specified in [RFC6513] and [RFC6514].
     This method is further described in Section 2.2.1.
 2.  Using the OPTIONAL explicit tracking mechanism based on the
     LIR-pF flag specified in [RFC8534].  This method, further
     described in Section 2.2.2, may be used if (and only if)
     segmented P-tunnels are not being used.

Rosen, et al. Standards Track [Page 9] RFC 8556 MVPN with BIER April 2018

2.2.1. Using the LIR Flag

 To determine the set of BFERs to which the packets of a given C-flow
 must be sent, a BFIR MUST originate a (C-S,C-G) S-PMSI A-D route for
 the given C-flow.  It MUST attach a PTA to that route and MUST set
 the Leaf Information Required (LIR) flag in the PTA.  Per [RFC6514],
 the BFERs that need to receive that C-flow will respond with
 (C-S,C-G) Leaf A-D routes.  By matching the received Leaf A-D routes
 to the originated S-PMSI A-D routes, the originator of the S-PMSI A-D
 route determines the set of BFERs that need to receive the multicast
 data flow that is identified in the NLRI of S-PMSI A-D route.
 Suppose that an ingress PE has originated an I-PMSI A-D route or a
 wildcard S-PMSI A-D route [RFC6625] with a PTA specifying a tunnel
 type of BIER.  Now suppose that the ingress PE originates an S-PMSI
 A-D route specifying (C-S,C-G), where (C-S,C-G) "matches" (according
 to the rules of [RFC6625]) the wildcard S-PMSI A-D route or the
 I-PMSI A-D route.  Instead of attaching a PTA specifying BIER to the
 (C-S,C-G) route, the ingress PE MAY attach a PTA specifying a tunnel
 type of "no tunnel information".  This is equivalent to attaching the
 same PTA attached to the matching "less specific" route.

2.2.2. Using the LIR-pF Flag

 If segmented P-tunnels are not being used, the BFIR can determine the
 set of BFERs that need to receive the packets of a given (C-S,C-G)
 C-flow as follows.  The BFIR MUST originate a wildcard S-PMSI A-D
 route (either (C-*,C-*), (C-*,C-G), or (C-S,C-G)), and the PTA of
 that route MUST use the following settings:
 o  The LIR-pF flag MUST be set.
 o  The tunnel type MUST be set to BIER.
 o  A non-zero MPLS label MUST be specified.
 Per [RFC8534], a BFER that needs to receive (C-S,C-G) traffic from
 the BFIR will respond with a Leaf A-D route.
 A BFIR MUST NOT use this method of finding the set of BFERs needing
 to receive a given C-flow unless it knows that all those BFERs
 support the LIR-pF flag.  How this is known is outside the scope of
 this document.

Rosen, et al. Standards Track [Page 10] RFC 8556 MVPN with BIER April 2018

 This method greatly reduces the number of S-PMSI A-D routes that a
 BFIR needs to originate; it can now originate as few as one such
 route (a (C-*,C-*) S-PMSI A-D route), rather than one for each
 C-flow.  However, the method does not provide a way for the BFIR to
 assign a distinct label to each C-flow.  Therefore, it cannot be used
 when segmented P-tunnels are in use (see Section 4 for an
 explanation).
 Note: If a BFIR originates a (C-*,C-*) S-PMSI A-D route with the
 LIR-pF flag set but also originates a more specific wildcard route
 that matches a particular (C-S,C-G), the BFERs will not originate
 Leaf A-D routes for that (C-S,C-G) unless the LIR-pF flag is also set
 in the more specific wildcard route.  If the BFIR also originates a
 (C-S,C-G) S-PMSI A-D route without the LIR flag set, the BFERs will
 not originate Leaf A-D routes for that (C-S,C-G) unless the LIR flag
 is also set in that route.

3. Use of the PMSI Tunnel Attribute in Leaf A-D Routes

 Before an egress PE can receive a (C-S,C-G) flow from a given ingress
 PE via BIER, the egress PE must have received one of the following
 x-PMSI A-D routes from the ingress PE:
 o  A (C-S,C-G) S-PMSI A-D route (i.e., an S-PMSI A-D route whose NLRI
    encodes (C-S,C-G)) and whose PTA specifies a tunnel type of BIER.
    If such a route is found, we refer to it as the "matching x-PMSI
    A-D route."
 o  A "less specific" x-PMSI A-D route (one specifying (C-*,C-*),
    (C-*,C-G), or (C-S,C-G)) whose PTA specifies a tunnel type of
    BIER, and that is the egress PE's "match for reception" of
    (C-S,C-G).
    The rules for determining which x-PMSI A-D route is the match for
    reception are given in [RFC6625].  However, these rules are
    modified here to exclude any x-PMSI A-D route that does not have a
    PTA or whose PTA specifies "no tunnel type".
    If such a route is found, we refer to it as the "matching x-PMSI
    A-D route."
 If no matching x-PMSI A-D route for (C-S,C-G) is found, the egress PE
 cannot receive the (C-S,C-G) flow from the ingress PE via BIER until
 such time as a matching route is received.

Rosen, et al. Standards Track [Page 11] RFC 8556 MVPN with BIER April 2018

 When an egress PE determines that it needs to receive a (C-S,C-G)
 flow from a particular ingress PE via BIER, it originates a Leaf A-D
 route.  Construction of the Leaf A-D route generally follows the
 procedures specified in [RFC6514] or, optionally, the procedures
 specified in [RFC8534].  However, when BIER is being used, the Leaf
 A-D route MUST carry a PTA that is constructed as follows:
 1.  The tunnel type MUST be set to BIER.
 2.  The MPLS Label field SHOULD be set to zero.
 3.  The sub-domain-id subfield of the Tunnel Identifier field (as
     defined in Section 2) MUST be set to the corresponding value from
     the PTA of the matching x-PMSI A-D route.
 4.  The BFR-id subfield of the Tunnel Identifier field MUST be set to
     the BFR-id in the sub-domain identified by the sub-domain-id
     subfield of the egress PE (BFER).
 5.  The BFR-prefix field of the Tunnel Identifier field (as defined
     in Section 2) MUST be set to the egress PE's (BFER's) BFR-prefix.
     The BFR-prefix need not be the same IP address that is carried in
     any other field of the Leaf A-D route.
 When an ingress PE receives such a Leaf A-D route, it learns the
 BFR-prefix of the egress PE from the PTA.  The ingress PE does not
 make any use the value of the PTA's MPLS label field.
 Failure to properly construct the PTA cannot always be detected by
 the protocol and will cause improper delivery of the data packets.

4. Data Plane

 The MVPN application plays the role of the "multicast flow overlay"
 as described in [RFC8279].

4.1. Encapsulation and Transmission

 To transmit an MVPN data packet, an ingress PE follows the rules of
 [RFC6625] to find the x-PMSI A-D route that is a "match for
 transmission" for that packet.  (In applying the rules of [RFC6625],
 any S-PMSI A-D route with a PTA specifying "no tunnel information" is
 ignored.)  If the matching route has a PTA specifying BIER, the
 (upstream-assigned) MPLS label from that PTA is pushed on the
 packet's label stack.  Then the packet is encapsulated in a BIER

Rosen, et al. Standards Track [Page 12] RFC 8556 MVPN with BIER April 2018

 header.  That is, the ingress PE functions as a BFIR.  The BIER
 sub-domain used for transmitting the packet is specified in the PTA
 of the above-mentioned x-PMSI A-D route.
 In order to create the proper BIER header for a given packet, the
 BFIR must know all the BFERs that need to receive that packet.  It
 determines this by finding all the Leaf A-D routes that correspond to
 the S-PMSI A-D route that is the packet's match for transmission.
 There are two different cases to consider:
 1.  The S-PMSI A-D route that is the match for transmission carries a
     PTA that has the LIR flag set but does not have the LIR-pF flag
     set.
     In this case, the corresponding Leaf A-D routes are those whose
     "route key" field is identical to the NLRI of the S-PMSI A-D
     route.
 2.  The S-PMSI A-D route that is the match for transmission carries a
     PTA that has the LIR-pF flag.
     In this case, the corresponding Leaf A-D routes are those whose
     "route key" field is derived from the NLRI of the S-PMSI A-D
     route according to the procedures described in Section 5.2 of
     [RFC8534].
 The Leaf A-D route from a given BFER will contain a PTA that
 specifies the BFER's BFR-prefix.  With this information, the BFIR can
 construct the BIER BitString.
 However, if the PTA of the Leaf A-D route from a given BFER specifies
 a sub-domain other than the one being used for transmitting the
 packet, the bit for that BFER cannot be determined and that BFER will
 not receive the packet.
 The BIER-encapsulated packet is then forwarded, according to the
 procedures described in [RFC8279] and [RFC8296].  (See especially
 Section 3, "Imposing and Processing the BIER Encapsulation" in
 [RFC8296].)

Rosen, et al. Standards Track [Page 13] RFC 8556 MVPN with BIER April 2018

4.2. Disposition

 When a BFER receives an MVPN multicast data packet that has been
 BIER-encapsulated, the BIER layer passes the following information to
 the multicast flow overlay:
 o  The sub-domain-id and the BFIR-id from the BIER header.  (As the
    sub-domain-id is inferred from the BIFT-id field of the BIER
    header, an implementation might choose to pass the BIFT-id rather
    than the sub-domain-id; this is an implementation matter.)
 o  The "payload", which is an MPLS packet whose top label is an
    upstream-assigned label.  In the data plane, the BFIR-id and the
    sub-domain-id provide the context in which the upstream-assigned
    label is interpreted.
 By looking up the upstream-assigned label in the appropriate context,
 the multicast flow overlay determines whether the BFER is an egress
 PE for the packet.
 Note that if segmented P-tunnels are in use, a BFER might be a
 P-tunnel segmentation border router rather than an egress PE, or a
 BFER might be both an egress PE and a P-tunnel segmentation border
 router.  Depending upon the role of the BFER for the given packet, it
 may need to follow the procedures of Section 4.2.1, the procedures of
 Section 4.2.2, or both.

4.2.1. At a BFER That Is an Egress PE

 From looking up the packet's upstream-assigned label in the context
 of the packet's BFIR-prefix, the egress PE determines the egress VRF
 for the packet.  From the IP header of the payload, the multicast
 states of the VRF, the upstream-assigned label, and the BFR-prefix,
 the egress PE can determine whether the packet needs to be forwarded
 out one or more VRF interfaces.

4.2.2. At a BFER That Is a P-tunnel Segmentation Boundary

 When segmented P-tunnels are being used, a BFER that receives a BIER-
 encapsulated MVPN multicast data packet may need to be forwarded on
 its next P-tunnel segment.  The choice of the next P-tunnel segment
 for the packet depends upon the C-flow to which the packet belongs.
 As long as the BFIR has assigned the MPLS label according to the
 constraints specified in Section 2.1, the BFIR will have assigned
 distinct upstream-assigned MPLS labels to distinct C-flows.  The BFER
 can thus select the proper "next P-tunnel segment" for a given packet
 simply by looking up the upstream-assigned label that immediately
 follows the BIER header.

Rosen, et al. Standards Track [Page 14] RFC 8556 MVPN with BIER April 2018

5. IANA Considerations

 IANA has assigned the codepoint 0x0B to BIER in the "P-Multicast
 Service Interface Tunnel (PMSI Tunnel) Tunnel Types" registry.

6. Security Considerations

 The procedures of this document do not, in themselves, provide
 privacy, integrity, or authentication for the control plane or the
 data plane.  For a discussion of the security considerations
 regarding the use of BIER, please see [RFC8279] and [RFC8296].
 Security considerations regarding VPN technology based on [RFC4364],
 [RFC6513], and [RFC6514] can be found in those RFCs.

7. References

7.1. Normative References

 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119,
            DOI 10.17487/RFC2119, March 1997,
            <https://www.rfc-editor.org/info/rfc2119>.
 [RFC4364]  Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
            Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
            2006, <https://www.rfc-editor.org/info/rfc4364>.
 [RFC5331]  Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
            Label Assignment and Context-Specific Label Space",
            RFC 5331, DOI 10.17487/RFC5331, August 2008,
            <https://www.rfc-editor.org/info/rfc5331>.
 [RFC6513]  Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/
            BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February
            2012, <https://www.rfc-editor.org/info/rfc6513>.
 [RFC6514]  Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
            Encodings and Procedures for Multicast in MPLS/BGP IP
            VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
            <https://www.rfc-editor.org/info/rfc6514>.
 [RFC6625]  Rosen, E., Ed., Rekhter, Y., Ed., Hendrickx, W., and
            R. Qiu, "Wildcards in Multicast VPN Auto-Discovery
            Routes", RFC 6625, DOI 10.17487/RFC6625, May 2012,
            <https://www.rfc-editor.org/info/rfc6625>.

Rosen, et al. Standards Track [Page 15] RFC 8556 MVPN with BIER April 2018

 [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
            2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
            May 2017, <https://www.rfc-editor.org/info/rfc8174>.
 [RFC8279]  Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
            Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
            Explicit Replication (BIER)", RFC 8279,
            DOI 10.17487/RFC8279, November 2017,
            <https://www.rfc-editor.org/info/rfc8279>.
 [RFC8296]  Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
            Tantsura, J., Aldrin, S., and I. Meilik, "Encapsulation
            for Bit Index Explicit Replication (BIER) in MPLS and Non-
            MPLS Networks", RFC 8296, DOI 10.17487/RFC8296, January
            2018, <https://www.rfc-editor.org/info/rfc8296>.
 [RFC8534]  Dolganow, A., Kotalwar, J., Rosen, E., Ed., and Z. Zhang,
            "Explicit Tracking with Wildcard Routes in Multicast VPN",
            RFC 8534, DOI 10.17487/RFC8534, February 2019,
            <https://www.rfc-editor.org/info/rfc8534>.

7.2. Informative References

 [RFC7524]  Rekhter, Y., Rosen, E., Aggarwal, R., Morin, T.,
            Grosclaude, I., Leymann, N., and S. Saad, "Inter-Area
            Point-to-Multipoint (P2MP) Segmented Label Switched Paths
            (LSPs)", RFC 7524, DOI 10.17487/RFC7524, May 2015,
            <https://www.rfc-editor.org/info/rfc7524>.
 [RFC7900]  Rekhter, Y., Ed., Rosen, E., Ed., Aggarwal, R., Cai, Y.,
            and T. Morin, "Extranet Multicast in BGP/IP MPLS VPNs",
            RFC 7900, DOI 10.17487/RFC7900, June 2016,
            <https://www.rfc-editor.org/info/rfc7900>.

Acknowledgments

 The authors wish to thank Jeffrey Zhang for his ideas and
 contributions to this work.  We also thank Stig Venaas for his review
 and comments.

Contributors

 IJsbrand Wijnands
 Cisco Systems, Inc.
 De Kleetlaan 6a
 Diegem  1831
 Belgium
 Email: ice@cisco.com

Rosen, et al. Standards Track [Page 16] RFC 8556 MVPN with BIER April 2018

Authors' Addresses

 Eric C. Rosen (editor)
 Juniper Networks, Inc.
 10 Technology Park Drive
 Westford, Massachusetts  01886
 United States of America
 Email: erosen52@gmail.com
 Mahesh Sivakumar
 Juniper Networks, Inc.
 1137 Innovation Way
 Sunnyvale, California  94089
 United States of America
 Email: sivakumar.mahesh@gmail.com
 Tony Przygienda
 Juniper Networks, Inc.
 1137 Innovation Way
 Sunnyvale, California  94089
 United States of America
 Email: prz@juniper.net
 Sam K Aldrin
 Google, Inc.
 1600 Amphitheatre Parkway
 Mountain View, California
 United States of America
 Email: aldrin.ietf@gmail.com
 Andrew Dolganow
 Nokia
 438B Alexandra Rd #08-07/10
 Alexandra Technopark
 Singapore  119968
 Email: andrew.dolganow@nokia.com

Rosen, et al. Standards Track [Page 17]

/data/webs/external/dokuwiki/data/pages/rfc/rfc8556.txt · Last modified: 2019/04/08 21:19 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki