GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc8532

Internet Engineering Task Force (IETF) D. Kumar Request for Comments: 8532 Cisco Category: Standards Track M. Wang ISSN: 2070-1721 Q. Wu, Ed.

                                                                Huawei
                                                             R. Rahman
                                                           S. Raghavan
                                                                 Cisco
                                                            April 2019
           Generic YANG Data Model for the Management of
    Operations, Administration, and Maintenance (OAM) Protocols
               That Use Connectionless Communications

Abstract

 This document presents a base YANG Data model for the management of
 Operations, Administration, and Maintenance (OAM) protocols that use
 connectionless communications.  The data model is defined using the
 YANG data modeling language, as specified in RFC 7950.  It provides a
 technology-independent abstraction of key OAM constructs for OAM
 protocols that use connectionless communication.  The base model
 presented here can be extended to include technology-specific
 details.
 There are two key benefits of this approach: First, it leads to
 uniformity between OAM protocols.  Second, it supports both nested
 OAM workflows (i.e., performing OAM functions at the same level or
 different levels through a unified interface) as well as interactive
 OAM workflows (i.e., performing OAM functions at the same level
 through a unified interface).

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 https://www.rfc-editor.org/info/rfc8532.

Kumar, et al. Standards Track [Page 1] RFC 8532 Connectionless OAM YANG Data Model April 2019

Copyright Notice

 Copyright (c) 2019 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (https://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Table of Contents

 1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
 2.  Conventions Used in This Document . . . . . . . . . . . . . .   4
   2.1.  Abbreviations . . . . . . . . . . . . . . . . . . . . . .   4
   2.2.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   5
   2.3.  Tree Diagrams . . . . . . . . . . . . . . . . . . . . . .   5
 3.  Overview of the Connectionless OAM Model  . . . . . . . . . .   5
   3.1.  TP Address  . . . . . . . . . . . . . . . . . . . . . . .   6
   3.2.  Tools . . . . . . . . . . . . . . . . . . . . . . . . . .   7
   3.3.  OAM Neighboring Test Points . . . . . . . . . . . . . . .   7
   3.4.  Test Point Location Information . . . . . . . . . . . . .   8
   3.5.  Test Point Locations  . . . . . . . . . . . . . . . . . .   8
   3.6.  Path Discovery Data . . . . . . . . . . . . . . . . . . .   8
   3.7.  Continuity Check Data . . . . . . . . . . . . . . . . . .   9
   3.8.  OAM Data Hierarchy  . . . . . . . . . . . . . . . . . . .   9
 4.  LIME Time Types YANG Module . . . . . . . . . . . . . . . . .  12
 5.  Connectionless OAM YANG Module  . . . . . . . . . . . . . . .  15
 6.  Connectionless Model Applicability  . . . . . . . . . . . . .  44
   6.1.  BFD Extension . . . . . . . . . . . . . . . . . . . . . .  45
     6.1.1.  Augment Method  . . . . . . . . . . . . . . . . . . .  45
     6.1.2.  Schema Mount  . . . . . . . . . . . . . . . . . . . .  47
   6.2.  LSP Ping Extension  . . . . . . . . . . . . . . . . . . .  49
     6.2.1.  Augment Method  . . . . . . . . . . . . . . . . . . .  49
     6.2.2.  Schema Mount  . . . . . . . . . . . . . . . . . . . .  50
 7.  Security Considerations . . . . . . . . . . . . . . . . . . .  52
 8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  54
 9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  54
   9.1.  Normative References  . . . . . . . . . . . . . . . . . .  54
   9.2.  Informative References  . . . . . . . . . . . . . . . . .  56
 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  58
 Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  59

Kumar, et al. Standards Track [Page 2] RFC 8532 Connectionless OAM YANG Data Model April 2019

1. Introduction

 Operations, Administration, and Maintenance (OAM) are important
 networking functions that allow operators to:
 1.  monitor network communications (i.e., reachability verification
     and Continuity Check)
 2.  troubleshoot failures (i.e., fault verification and localization)
 3.  monitor service-level agreements and performance (i.e.,
     performance management)
 An overview of OAM tools is presented in [RFC7276].
 Ping and Traceroute (see [RFC792] and [RFC4443]) are respectively
 well-known fault verification and isolation tools for IP networks.
 Over the years, different technologies have developed similar
 toolsets for equivalent purposes.
 The different sets of OAM tools may support both connection-oriented
 or connectionless technologies.  In connection-oriented technologies,
 a connection is established prior to the transmission of data.  After
 the connection is established, no additional control information such
 as signaling or operations and maintenance information is required to
 transmit the actual user data.  In connectionless technologies, data
 is typically sent between communicating endpoints without prior
 arrangement, but control information is required to identify the
 destination (e.g., [G.800] and [RFC7276]).  The YANG data model for
 OAM protocols using connection-oriented communications is specified
 in [RFC8531].
 This document defines a base YANG data model for OAM protocols that
 use connectionless communications.  The data model is defined using
 the YANG data modeling language [RFC7950].  This generic YANG data
 model for connectionless OAM includes only configuration and state
 data.  It can be used in conjunction with the data retrieval method
 model described in [RFC8533], which focuses on the data retrieval
 procedures such as RPC, or it can be used independently of this data
 retrieval method model.

Kumar, et al. Standards Track [Page 3] RFC 8532 Connectionless OAM YANG Data Model April 2019

2. Conventions Used in This Document

 The following terms are defined in [RFC6241] and are used in this
 specification:
 o  client
 o  configuration data
 o  server
 o  state data
 The following terms are defined in [RFC7950] and are used in this
 specification:
 o  augment
 o  data model
 o  data node
 The terminology for describing YANG data models is found in
 [RFC7950].

2.1. Abbreviations

 BFD - Bidirectional Forwarding Detection [RFC5880].
 RPC - Remote Procedure Call [RFC1831].
 DSCP - Differentiated Services Code Point.
 VRF - Virtual Routing and Forwarding [RFC4382].
 OWAMP - One-Way Active Measurement Protocol [RFC4656].
 TWAMP - Two-Way Active Measurement Protocol [RFC5357].
 AS - Autonomous System.
 LSP - Label Switched Path.
 TE - Traffic Engineering.
 MPLS - Multiprotocol Label Switching.
 NI - Network Instance.

Kumar, et al. Standards Track [Page 4] RFC 8532 Connectionless OAM YANG Data Model April 2019

 PTP - Precision Time Protocol [IEEE.1588v2].
 NTP - Network Time Protocol [RFC5905].

2.2. Terminology

 MAC - Media Access Control.
 MAC address - Address for the data-link layer interface.
 TP - Test Point.  The TP is a functional entity that is defined at a
 node in the network and can initiate and/or react to OAM diagnostic
 tests.  This document focuses on the data-plane functionality of TPs.
 RPC operation - A specific Remote Procedure Call.
 CC - A Continuity Check [RFC7276] is used to verify that a
 destination is reachable and therefore also referred to as
 reachability verification.

2.3. Tree Diagrams

  Tree diagrams used in this document follow the notation defined in
  [RFC8340].

3. Overview of the Connectionless OAM Model

 The YANG data model for OAM protocols that use connectionless
 communications has been split into two modules:
 o  The "ietf-lime-time-types" module provides common definitions such
    as Time-related data types and Timestamp-related data types.
 o  The "ietf-connectionless-oam" module defines technology-
    independent abstraction of key OAM constructs for OAM protocols
    that use connectionless communication.
 The "ietf-connectionless-oam" module augments the "/networks/network/
 node" path defined in the "ietf-network" module [RFC8345] with the
 'test-point-locations' grouping defined in Section 3.5.  The network
 nodes in the "/networks/network/node" path are used to describe the
 network hierarchies and the inventory of nodes contained in a
 network.
 Under the 'test-point-locations' grouping, each test point location
 is chosen based on the 'tp-location-type' leaf, which, when chosen,
 leads to a container that includes a list of 'test-point-locations'.

Kumar, et al. Standards Track [Page 5] RFC 8532 Connectionless OAM YANG Data Model April 2019

 Each 'test-point-locations' list includes a 'test-point-location-
 info' grouping.  The 'test-point-location-info' grouping includes:
 o  'tp-technology' grouping,
 o  'tp-tools' grouping, and
 o  'connectionless-oam-tps' grouping.
 The groupings of 'tp-address' and 'tp-address-ni' are kept out of the
 'test-point-location-info' grouping to make it addressing agnostic
 and allow varied composition.  Depending upon the choice of the
 'tp-location-type' (determined by the 'tp-address-ni'), each
 container differs in its composition of 'test-point-locations', while
 the 'test-point-location-info' is a common aspect of every
 'test-point-locations'.
 The 'tp-address-ni' grouping is used to describe the corresponding
 network instance.  The 'tp-technology' grouping indicates OAM
 technology details.  The 'connectionless-oam-tps' grouping is used to
 describe the relationship of one test point with other test points.
 The 'tp-tools' grouping describes the OAM tools supported.
 In addition, at the top of the model, there is an 'cc-oper-data'
 container for session statistics.  A grouping is also defined for
 common session statistics, and these are only applicable for
 proactive OAM sessions (see Section 3.2).

3.1. TP Address

 With connectionless OAM protocols, the TP address can be one of the
 following types:
 o  MAC address [RFC6136] at the data-link layer for TPs
 o  IPv4 or IPv6 address at the IP layer for TPs
 o  TP-attribute identifying a TP associated with an application-layer
    function
 o  Router-id to represent the device or node, which is commonly used
    to identify nodes in routing and other control-plane protocols
    [RFC8294].
 To define a forwarding treatment of a test packet, the 'tp-address'
 grouping needs to be associated with additional parameters, e.g.,
 DSCP for IP or Traffic Class [RFC5462] for MPLS.  In the generic

Kumar, et al. Standards Track [Page 6] RFC 8532 Connectionless OAM YANG Data Model April 2019

 connectionless OAM YANG data model, these parameters are not
 explicitly configured.  The model user can add corresponding
 parameters according to their requirements.

3.2. Tools

 The different OAM tools may be used in one of two basic types of
 activation: proactive and on-demand.  Proactive OAM refers to OAM
 actions that are carried out continuously to permit proactive
 reporting of faults.  The proactive OAM method requires persistent
 configuration.  On-demand OAM refers to OAM actions that are
 initiated via manual intervention for a limited time to carry out
 specific diagnostics.  The on-demand OAM method requires only
 transient configuration (e.g., [RFC7276] and [G.8013]).  In
 connectionless OAM, the 'session-type' grouping is defined to
 indicate which kind of activation will be used by the current
 session.
 In connectionless OAM, the tools attribute is used to describe a
 toolset for fault detection and isolation.  In addition, it can serve
 as a constraint condition when the base model is extended to a
 specific OAM technology.  For example, to fulfill the ICMP PING
 configuration, the "../coam:continuity-check" leaf should be set to
 "true", and then the LIME base model should be augmented with details
 specific to ICMP PING.

3.3. OAM Neighboring Test Points

 Given that typical network communication stacks have a multi-layer
 architecture, the set of associated OAM protocols has also a multi-
 layer structure; each communication layer in the stack may have its
 own OAM protocol [RFC7276] that may also be linked to a specific
 administrative domain.  Management of these OAM protocols will
 necessitate associated test points in the nodes accessible by
 appropriate management domains.  Accordingly, a given network
 interface may actually present several test points.
 Each OAM test point may have an associated list of neighboring test
 points that are in other layers up and down the protocol stack for
 the same interface and are therefore related to the current test
 point.  This allows users to easily navigate between related
 neighboring layers to efficiently troubleshoot a defect.  In this
 model, the 'position' leaf defines the relative position of the
 neighboring test point corresponding to the current test point, and
 it is provided to allow correlation of faults at different locations.
 If there is one neighboring test point placed before the current test
 point, the 'position' leaf is set to -1.  If there is one neighboring

Kumar, et al. Standards Track [Page 7] RFC 8532 Connectionless OAM YANG Data Model April 2019

 test point placed after the current test point, the 'position' leaf
 is set to 1.  If there is no neighboring test point placed before or
 after the current test point, the 'position' leaf is set to 0.
   +-- oam-neighboring-tps* [index]
      +-- index?                         uint16
      +-- position?                      int8
      +-- (tp-location)?
         +--:(mac-address)
         |  +-- mac-address-location?    yang:mac-address
         +--:(ipv4-address)
         |  +-- ipv4-address-location?   inet:ipv4-address
         +--:(ipv6-address)
         |  +-- ipv6-address-location?   inet:ipv6-address
         +--:(as-number)
         |  +-- as-number-location?      inet:as-number
         +--:(router-id)
            +-- router-id-location?      rt:router-id

3.4. Test Point Location Information

 This is a generic grouping for Test Point Location Information (i.e.,
 'test-point-location-info' grouping).  It provides details of Test
 Point Location using the 'tp-technology', 'tp-tools', and
 'oam-neighboring-tps' groupings, all of which are defined above.

3.5. Test Point Locations

 This is a generic grouping for Test Point Locations.  'tp-location-
 type' leaf is used to define location types -- for example,
 'ipv4-location-type', 'ipv6-location-type', etc.  Container is
 defined under each location type containing a list keyed to a test
 point address, Test Point Location Information defined in the section
 above, and network instance name (e.g., VRF instance name) if
 required.

3.6. Path Discovery Data

 This is a generic grouping for the path discovery data model that can
 be retrieved by any data retrieval method, including RPC operations.
 Path discovery data output from methods, includes 'src-test-point'
 container, 'dst-test-point' container, 'sequence-number' leaf,
 'hop-cnt' leaf, session statistics of various kinds, and information
 related to path verification and path trace.  Path discovery includes
 data to be retrieved on a 'per-hop' basis via a list of 'path-trace-
 info-list' items which includes information such as 'timestamp'
 grouping, 'ingress-intf-name', 'egress-intf-name', and 'app-meta-
 data'.  The path discovery data model is made generic enough to allow

Kumar, et al. Standards Track [Page 8] RFC 8532 Connectionless OAM YANG Data Model April 2019

 different methods of data retrieval.  None of the fields are made
 mandatory for that reason.  Note that a set of retrieval methods are
 defined in [RFC8533].

3.7. Continuity Check Data

 This is a generic grouping for the Continuity Check data model that
 can be retrieved by any data retrieval methods including RPC
 operations.  Continuity Check data output from methods, includes
 'src-test-point' container, 'dst-test-point' container,
 'sequence-number' leaf, 'hop-cnt' leaf, and session statistics of
 various kinds.  The Continuity Check data model is made generic
 enough to allow different methods of data retrieval.  None of the
 fields are made mandatory for that reason.  Noted that a set of
 retrieval methods are defined in [RFC8533].

3.8. OAM Data Hierarchy

 The complete data hierarchy related to the OAM YANG data model is
 presented below.
module: ietf-connectionless-oam
    +--ro cc-session-statistics-data {continuity-check}?
       +--ro cc-session-statistics* [type]
          +--ro type                           identityref
          +--ro cc-ipv4-sessions-statistics
          |  +--ro cc-session-statistics
          |     +--ro session-count?              uint32
          |     +--ro session-up-count?           uint32
          |     +--ro session-down-count?         uint32
          |     +--ro session-admin-down-count?   uint32
          +--ro cc-ipv6-sessions-statistics
             +--ro cc-session-statistics
                +--ro session-count?              uint32
                +--ro session-up-count?           uint32
                +--ro session-down-count?         uint32
                +--ro session-admin-down-count?   uint32
  augment /nd:networks/nd:network/nd:node:
    +--rw tp-location-type?                identityref
    +--rw ipv4-location-type
    |  +--rw test-point-ipv4-location-list
    |     +--rw test-point-locations* [ipv4-location ni]
    |        +--rw ipv4-location          inet:ipv4-address
    |        +--rw ni                     routing-instance-ref
    |        +--rw (technology)?
    |        |  +--:(technology-null)
    |        |     +--rw tech-null?             empty
    |        +--rw tp-tools

Kumar, et al. Standards Track [Page 9] RFC 8532 Connectionless OAM YANG Data Model April 2019

    |        |  +--rw continuity-check    boolean
    |        |  +--rw path-discovery      boolean
    |        +--rw root?                  <anydata>
    |        +--rw oam-neighboring-tps* [index]
    |           +--rw index                    uint16
    |           +--rw position?                int8
    |           +--rw (tp-location)?
    |              +--:(mac-address)
    |              |  +--rw mac-address-location?    yang:mac-address
    |              +--:(ipv4-address)
    |              |  +--rw ipv4-address-location?   inet:ipv4-address
    |              +--:(ipv6-address)
    |              |  +--rw ipv6-address-location?   inet:ipv6-address
    |              +--:(as-number)
    |              |  +--rw as-number-location?      inet:as-number
    |              +--:(router-id)
    |                 +--rw router-id-location?      rt:router-id
    +--rw ipv6-location-type
    |  +--rw test-point-ipv6-location-list
    |     +--rw test-point-locations* [ipv6-location ni]
    |        +--rw ipv6-location          inet:ipv6-address
    |        +--rw ni                     routing-instance-ref
    |        +--rw (technology)?
    |        |  +--:(technology-null)
    |        |     +--rw tech-null?             empty
    |        +--rw tp-tools
    |        |  +--rw continuity-check    boolean
    |        |  +--rw path-discovery      boolean
    |        +--rw root?                  <anydata>
    |        +--rw oam-neighboring-tps* [index]
    |           +--rw index                    uint16
    |           +--rw position?                int8
    |           +--rw (tp-location)?
    |              +--:(mac-address)
    |              |  +--rw mac-address-location?    yang:mac-address
    |              +--:(ipv4-address)
    |              |  +--rw ipv4-address-location?   inet:ipv4-address
    |              +--:(ipv6-address)
    |              |  +--rw ipv6-address-location?   inet:ipv6-address
    |              +--:(as-number)
    |              |  +--rw as-number-location?      inet:as-number
    |              +--:(router-id)
    |                 +--rw router-id-location?      rt:router-id
    +--rw mac-location-type
    |  +--rw test-point-mac-address-location-list
    |     +--rw test-point-locations* [mac-address-location]
    |        +--rw mac-address-location    yang:mac-address
    |        +--rw (technology)?

Kumar, et al. Standards Track [Page 10] RFC 8532 Connectionless OAM YANG Data Model April 2019

    |        |  +--:(technology-null)
    |        |     +--rw tech-null?              empty
    |        +--rw tp-tools
    |        |  +--rw continuity-check    boolean
    |        |  +--rw path-discovery      boolean
    |        +--rw root?                   <anydata>
    |        +--rw oam-neighboring-tps* [index]
    |           +--rw index                    uint16
    |           +--rw position?                int8
    |           +--rw (tp-location)?
    |              +--:(mac-address)
    |              |  +--rw mac-address-location?    yang:mac-address
    |              +--:(ipv4-address)
    |              |  +--rw ipv4-address-location?   inet:ipv4-address
    |              +--:(ipv6-address)
    |              |  +--rw ipv6-address-location?   inet:ipv6-address
    |              +--:(as-number)
    |              |  +--rw as-number-location?      inet:as-number
    |              +--:(router-id)
    |                 +--rw router-id-location?      rt:router-id
    +--rw group-as-number-location-type
    |  +--rw test-point-as-number-location-list
    |     +--rw test-point-locations* [as-number-location]
    |        +--rw as-number-location     inet:as-number
    |        +--rw ni?                    routing-instance-ref
    |        +--rw (technology)?
    |        |  +--:(technology-null)
    |        |     +--rw tech-null?             empty
    |        +--rw tp-tools
    |        |  +--rw continuity-check    boolean
    |        |  +--rw path-discovery      boolean
    |        +--rw root?                  <anydata>
    |        +--rw oam-neighboring-tps* [index]
    |           +--rw index                    uint16
    |           +--rw position?                int8
    |           +--rw (tp-location)?
    |              +--:(mac-address)
    |              |  +--rw mac-address-location?    yang:mac-address
    |              +--:(ipv4-address)
    |              |  +--rw ipv4-address-location?   inet:ipv4-address
    |              +--:(ipv6-address)
    |              |  +--rw ipv6-address-location?   inet:ipv6-address
    |              +--:(as-number)
    |              |  +--rw as-number-location?      inet:as-number
    |              +--:(router-id)
    |                 +--rw router-id-location?      rt:router-id
    +--rw group-router-id-location-type
       +--rw test-point-system-info-location-list

Kumar, et al. Standards Track [Page 11] RFC 8532 Connectionless OAM YANG Data Model April 2019

          +--rw test-point-locations* [router-id-location]
             +--rw router-id-location     rt:router-id
             +--rw ni?                    routing-instance-ref
             +--rw (technology)?
             |  +--:(technology-null)
             |     +--rw tech-null?             empty
             +--rw tp-tools
             |  +--rw continuity-check    boolean
             |  +--rw path-discovery      boolean
             +--rw root?                  <anydata>
             +--rw oam-neighboring-tps* [index]
                +--rw index                    uint16
                +--rw position?                int8
                +--rw (tp-location)?
                   +--:(mac-address)
                   |  +--rw mac-address-location?    yang:mac-address
                   +--:(ipv4-address)
                   |  +--rw ipv4-address-location?   inet:ipv4-address
                   +--:(ipv6-address)
                   |  +--rw ipv6-address-location?   inet:ipv6-address
                   +--:(as-number)
                   |  +--rw as-number-location?      inet:as-number
                   +--:(router-id)
                      +--rw router-id-location?      rt:router-id

4. LIME Time Types YANG Module

 <CODE BEGINS> file "ietf-lime-time-types@2019-04-16.yang"
 module ietf-lime-time-types {
   yang-version 1.1;
   namespace "urn:ietf:params:xml:ns:yang:ietf-lime-time-types";
   prefix lime;
   organization
     "IETF LIME Working Group";
   contact
     "WG Web:   <https://datatracker.ietf.org/wg/lime>
      WG List:  <mailto:lmap@ietf.org>
      Editor:   Qin Wu
                <bill.wu@huawei.com>";
   description
     "This module provides time-related definitions used by the data
      models written for Layer Independent OAM Management in the
      Multi-Layer Environment (LIME).  This module defines
      identities but no schema tree elements.

Kumar, et al. Standards Track [Page 12] RFC 8532 Connectionless OAM YANG Data Model April 2019

      Copyright (c) 2019 IETF Trust and the persons identified as
      authors of the code.  All rights reserved.
      Redistribution and use in source and binary forms, with or
      without modification, is permitted pursuant to, and subject
      to the license terms contained in, the Simplified BSD License
      set forth in Section 4.c of the IETF Trust's Legal Provisions
      Relating to IETF Documents
      (http://trustee.ietf.org/license-info).
      This version of this YANG module is part of RFC 8532; see
      the RFC itself for full legal notices.";
   revision 2019-04-16 {
     description
       "Initial version.";
     reference
       "RFC 8532: Generic YANG Data Model for the Management of
        Operations, Administration, and Maintenance (OAM) Protocols
        That Use Connectionless Communications";
   }
   /*** Collection of common types related to time ***/
   /*** Time unit identity ***/
   identity time-unit-type {
     description
       "Time unit type.";
   }
   identity hours {
     base time-unit-type;
     description
       "Time unit in hours.";
   }
   identity minutes {
     base time-unit-type;
     description
       "Time unit in minutes.";
   }
   identity seconds {
     base time-unit-type;
     description
       "Time unit in seconds.";
   }

Kumar, et al. Standards Track [Page 13] RFC 8532 Connectionless OAM YANG Data Model April 2019

   identity milliseconds {
     base time-unit-type;
     description
       "Time unit in milliseconds.";
   }
   identity microseconds {
     base time-unit-type;
     description
       "Time unit in microseconds.";
   }
   identity nanoseconds {
     base time-unit-type;
     description
       "Time unit in nanoseconds.";
   }
   /*** Timestamp format Identity ***/
   identity timestamp-type {
     description
       "Base identity for Timestamp Type.";
   }
   identity truncated-ptp {
     base timestamp-type;
     description
       "Identity for 64-bit short-format PTP timestamp.";
   }
   identity truncated-ntp {
     base timestamp-type;
     description
       "Identity for 32-bit short-format NTP timestamp.";
   }
   identity ntp64 {
     base timestamp-type;
     description
       "Identity for 64-bit NTP timestamp.";
   }
   identity icmp {
     base timestamp-type;
     description
       "Identity for 32-bit ICMP timestamp.";
   }

Kumar, et al. Standards Track [Page 14] RFC 8532 Connectionless OAM YANG Data Model April 2019

   identity ptp80 {
     base timestamp-type;
     description
       "Identity for 80-bit PTP timestamp.";
   }
 }
 <CODE ENDS>

5. Connectionless OAM YANG Module

 This module imports the Core YANG Derived Types definition ("ietf-
 yang-types" module) and Internet-Specific Derived Types definitions
 ("ietf-inet-types" module) from [RFC6991], the "ietf-routing-types"
 module from [RFC8294], the "ietf-interfaces" module from [RFC8343],
 the "ietf-network" module from [RFC8345], the "ietf-network-instance"
 module from [RFC8529], and the "ietf-lime-time-types" module in
 Section 4.  This module references [IEEE.1588v1], [IEEE.1588v2],
 [RFC8029], and additional RFCs cited elsewhere in this document.
 <CODE BEGINS> file "ietf-connectionless-oam@2019-04-16.yang"

module ietf-connectionless-oam {

yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-connectionless-oam";
prefix cl-oam;
import ietf-yang-schema-mount {
  prefix yangmnt;
}
import ietf-network {
  prefix nd;
}
import ietf-yang-types {
  prefix yang;
}
import ietf-interfaces {
  prefix if;
}
import ietf-inet-types {
  prefix inet;
}
import ietf-network-instance {
  prefix ni;
}
import ietf-routing-types {
  prefix rt;
}

Kumar, et al. Standards Track [Page 15] RFC 8532 Connectionless OAM YANG Data Model April 2019

import ietf-lime-time-types {
  prefix lime;
}
organization
  "IETF LIME Working Group";
contact
  "WG Web:   <https://datatracker.ietf.org/wg/lime>
   WG List:  <mailto:lmap@ietf.org>
   Deepak Kumar <dekumar@cisco.com>
   Qin Wu <bill.wu@huawei.com>
   Srihari Raghavan <srihari@cisco.com>
   Michael Wang <wangzitao@huawei.com>
   Reshad Rahman <rrahman@cisco.com>";
description
  "This YANG module defines the generic configuration,
   data model, and statistics for OAM protocols using
   connectionless communications, described in a
   protocol independent manner.  It is assumed that each
   protocol maps corresponding abstracts to its native
   format.  Each protocol may extend the YANG data model defined
   here to include protocol specific extensions.
   Copyright (c) 2019 IETF Trust and the persons identified as
   authors of the code.  All rights reserved.
   Redistribution and use in source and binary forms, with or
   without modification, is permitted pursuant to, and subject
   to the license terms contained in, the Simplified BSD License
   set forth in Section 4.c of the IETF Trust's Legal Provisions
   Relating to IETF Documents
   (http://trustee.ietf.org/license-info).
   This version of this YANG module is part of RFC 8532; see
   the RFC itself for full legal notices.";
revision 2019-04-16 {
  description
    "Base model for Connectionless Operations, Administration,
     and Maintenance (OAM).";
  reference
    "RFC 8532: Generic YANG Data Model for the Management of
     Operations, Administration, and Maintenance (OAM) Protocols
     That Use Connectionless Communications";
}
feature connectionless {

Kumar, et al. Standards Track [Page 16] RFC 8532 Connectionless OAM YANG Data Model April 2019

  description
    "This feature indicates that the OAM solution is connectionless.";
}
feature continuity-check {
  description
    "This feature indicates that the server supports
     executing a Continuity Check OAM command and
     returning a response.  Servers that do not advertise
     this feature will not support executing
     Continuity Check commands or the RPC operation model for
     Continuity Check commands.";
}
feature path-discovery {
  description
    "This feature indicates that the server supports
     executing a path discovery OAM command and
     returning a response.  Servers that do not advertise
     this feature will not support executing
     path discovery commands or the RPC operation model for
     path discovery commands.";
}
feature ptp-long-format {
  description
    "This feature indicates that the timestamp is PTP long format.";
}
feature ntp-short-format {
  description
    "This feature indicates that the timestamp is NTP short format.";
}
feature icmp-timestamp {
  description
    "This feature indicates that the timestamp is ICMP timestamp.";
}
identity traffic-type {
  description
    "This is the base identity of the traffic type,
     which includes IPv4, IPv6, etc.";
}
identity ipv4 {
  base traffic-type;
  description

Kumar, et al. Standards Track [Page 17] RFC 8532 Connectionless OAM YANG Data Model April 2019

    "identity for IPv4 traffic type.";
}
identity ipv6 {
  base traffic-type;
  description
    "identity for IPv6 traffic type.";
}
identity address-attribute-types {
  description
    "This is the base identity of the address attribute types, which
     are Generic IPv4/IPv6 Prefix, BGP Labeled IPv4/IPv6 Prefix,
     Tunnel ID, PW ID, VPLS VE ID, etc. (See RFC 8029 for details.)";
}
typedef address-attribute-type {
  type identityref {
    base address-attribute-types;
  }
  description
    "Target address attribute type.";
}
typedef percentage {
  type decimal64 {
    fraction-digits 5;
    range "0..100";
  }
  description
    "Percentage.";
}
typedef routing-instance-ref {
  type leafref {
    path "/ni:network-instances/ni:network-instance/ni:name";
  }
  description
    "This type is used for leafs that reference a routing instance
     configuration.";
}
grouping cc-session-statistics {
  description
    "Grouping for session statistics.";
  container cc-session-statistics {
    description
      "CC session counters.";

Kumar, et al. Standards Track [Page 18] RFC 8532 Connectionless OAM YANG Data Model April 2019

    leaf session-count {
      type uint32;
      default "0";
      description
        "Number of Continuity Check sessions.
         A value of zero indicates that no session
         count is sent.";
    }
    leaf session-up-count {
      type uint32;
      default "0";
      description
        "Number of sessions that are up.
         A value of zero indicates that no up
         session count is sent.";
    }
    leaf session-down-count {
      type uint32;
      default "0";
      description
        "Number of sessions that are down.
         A value of zero indicates that no down
         session count is sent.";
    }
    leaf session-admin-down-count {
      type uint32;
      default "0";
      description
        "Number of sessions that are admin-down.
         A value of zero indicates that no admin-
         down session count is sent.";
    }
  }
}
grouping session-packet-statistics {
  description
    "Grouping for statistics per session packet.";
  container session-packet-statistics {
    description
      "Statistics per session packet.";
    leaf rx-packet-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of received OAM packets.

Kumar, et al. Standards Track [Page 19] RFC 8532 Connectionless OAM YANG Data Model April 2019

         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf tx-packet-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of transmitted OAM packets.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf rx-bad-packet {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total number of received bad OAM packets.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf tx-packet-failed {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total number of OAM packets that failed when sent.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
  }
}

Kumar, et al. Standards Track [Page 20] RFC 8532 Connectionless OAM YANG Data Model April 2019

grouping cc-per-session-statistics {
  description
    "Grouping for per-session statistics.";
  container cc-per-session-statistics {
    description
      "Per-session statistics.";
    leaf create-time {
      type yang:date-and-time;
      description
        "Time and date when session is created.";
    }
    leaf last-down-time {
      type yang:date-and-time;
      description
        "Time and date of the last time session was down.";
    }
    leaf last-up-time {
      type yang:date-and-time;
      description
        "Time and date of the last time session was up.";
    }
    leaf down-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of Continuity Check sessions down.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf admin-down-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of Continuity Check sessions admin down.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    uses session-packet-statistics;

Kumar, et al. Standards Track [Page 21] RFC 8532 Connectionless OAM YANG Data Model April 2019

  }
}
grouping session-error-statistics {
  description
    "Grouping for per-session error statistics.";
  container session-error-statistics {
    description
      "Per-session error statistics.";
    leaf packet-loss-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of received packet drops.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf loss-ratio {
      type percentage;
      description
        "Loss ratio of the packets.  Expressed as percentage
         of packets lost with respect to packets sent.";
    }
    leaf packet-reorder-count {
      type uint32 {
        range "0..4294967295";
      }
      default "0";
      description
        "Total count of received packets that were reordered.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf packets-out-of-seq-count {
      type uint32 {
        range "0..4294967295";
      }
      description
        "Total count of packets received out of sequence.
         The value of count will be set to zero (0)

Kumar, et al. Standards Track [Page 22] RFC 8532 Connectionless OAM YANG Data Model April 2019

         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf packets-dup-count {
      type uint32 {
        range "0..4294967295";
      }
      description
        "Total count of received packet duplicates.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
  }
}
grouping session-delay-statistics {
  description
    "Grouping for delay statistics per session.";
  container session-delay-statistics {
    description
      "Session delay summarized information.  By default, a
       one-way measurement protocol (e.g., OWAMP) is used
       to measure delay.  When a two-way measurement protocol
       (e.g., TWAMP) is used instead, it can be indicated
       using the protocol-id defined in RPC operation of
       retrieval methods for connectionless OAM (RFC 8533),
       i.e., set protocol-id as OWAMP.  Note that only one
       measurement protocol for delay is specified for
       interoperability reasons.";
    leaf time-unit-value {
      type identityref {
        base lime:time-unit-type;
      }
      default "lime:milliseconds";
      description
        "Time units, where the options are s, ms, ns, etc.";
    }
    leaf min-delay-value {
      type uint32;
      description
        "Minimum delay value observed.";
    }
    leaf max-delay-value {

Kumar, et al. Standards Track [Page 23] RFC 8532 Connectionless OAM YANG Data Model April 2019

      type uint32;
      description
        "Maximum delay value observed.";
    }
    leaf average-delay-value {
      type uint32;
      description
        "Average delay value observed.";
    }
  }
}
grouping session-jitter-statistics {
  description
    "Grouping for per session jitter statistics.";
  container session-jitter-statistics {
    description
      "Summarized information about session jitter.  By default,
       jitter is measured using IP Packet Delay Variation
       (IPDV) as defined in RFC 3393.  When the other measurement
       method is used instead (e.g., Packet Delay Variation used
       in ITU-T Recommendation Y.1540, it can be indicated using
       protocol-id-meta-data defined in RPC operation of
       retrieval methods for connectionless OAM (RFC 8533).
       Note that only one measurement method for jitter is
       specified for interoperability reasons.";
    leaf unit-value {
      type identityref {
        base lime:time-unit-type;
      }
      default "lime:milliseconds";
      description
        "Time units, where the options are s, ms, ns, etc.";
    }
    leaf min-jitter-value {
      type uint32;
      description
        "Minimum jitter value observed.";
    }
    leaf max-jitter-value {
      type uint32;
      description
        "Maximum jitter value observed.";
    }
    leaf average-jitter-value {
      type uint32;
      description
        "Average jitter value observed.";

Kumar, et al. Standards Track [Page 24] RFC 8532 Connectionless OAM YANG Data Model April 2019

    }
  }
}
grouping session-path-verification-statistics {
  description
    "Grouping for path verification statistics per session.";
  container session-path-verification-statistics {
    description
      "OAM path verification statistics per session.";
    leaf verified-count {
      type uint32 {
        range "0..4294967295";
      }
      description
        "Total number of OAM packets that
         went through a path as intended.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
    leaf failed-count {
      type uint32 {
        range "0..4294967295";
      }
      description
        "Total number of OAM packets that
         went through an unintended path.
         The value of count will be set to zero (0)
         on creation and will thereafter increase
         monotonically until it reaches a maximum value
         of 2^32-1 (4294967295 decimal), when it wraps
         around and starts increasing again from zero.";
    }
  }
}
grouping session-type {
  description
    "This object indicates which kind of activation will
     be used by the current session.";
  leaf session-type {
    type enumeration {
      enum proactive {
        description
          "The current session is a proactive session.";

Kumar, et al. Standards Track [Page 25] RFC 8532 Connectionless OAM YANG Data Model April 2019

      }
      enum on-demand {
        description
          "The current session is an on-demand session.";
      }
    }
    default "on-demand";
    description
      "Indicate which kind of activation will be used
       by the current session.";
  }
}
identity tp-address-technology-type {
  description
    "Test point address type.";
}
identity mac-address-type {
  base tp-address-technology-type;
  description
    "MAC address type.";
}
identity ipv4-address-type {
  base tp-address-technology-type;
  description
    "IPv4 address type.";
}
identity ipv6-address-type {
  base tp-address-technology-type;
  description
    "IPv6 address type.";
}
identity tp-attribute-type {
  base tp-address-technology-type;
  description
    "Test point attribute type.";
}
identity router-id-address-type {
  base tp-address-technology-type;
  description
    "System ID address type.";
}

Kumar, et al. Standards Track [Page 26] RFC 8532 Connectionless OAM YANG Data Model April 2019

identity as-number-address-type {
  base tp-address-technology-type;
  description
    "AS number address type.";
}
identity route-distinguisher-address-type {
  base tp-address-technology-type;
  description
    "Route Distinguisher address type.";
}
grouping tp-address {
  leaf tp-location-type {
    type identityref {
      base tp-address-technology-type;
    }
    mandatory true;
    description
      "Test point address type.";
  }
  container mac-address {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:mac-address-type')" {
      description
        "MAC address type.";
    }
    leaf mac-address {
      type yang:mac-address;
      mandatory true;
      description
        "MAC address.";
    }
    description
      "MAC address based TP addressing.";
  }
  container ipv4-address {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:ipv4-address-type')" {
      description
        "IPv4 address type.";
    }
    leaf ipv4-address {
      type inet:ipv4-address;
      mandatory true;
      description
        "IPv4 address.";
    }

Kumar, et al. Standards Track [Page 27] RFC 8532 Connectionless OAM YANG Data Model April 2019

    description
      "IP address based TP addressing.";
  }
  container ipv6-address {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:ipv6-address-type')" {
      description
        "IPv6 address type.";
    }
    leaf ipv6-address {
      type inet:ipv6-address;
      mandatory true;
      description
        "IPv6 address.";
    }
    description
      "IPv6 address based TP addressing.";
  }
  container tp-attribute {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:tp-attribute-type')" {
      description
        "Test point attribute type.";
    }
    leaf tp-attribute-type {
      type address-attribute-type;
      description
        "Test point type.";
    }
    choice tp-attribute-value {
      description
        "Test point value.";
      case ip-prefix {
        leaf ip-prefix {
          type inet:ip-prefix;
          description
            "Generic IPv4/IPv6 prefix.  See Sections 3.2.13 and
             3.2.14 of RFC 8029.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
      }
      case bgp {
        leaf bgp {
          type inet:ip-prefix;
          description
            "BGP Labeled IPv4/IPv6 Prefix.  See Sections

Kumar, et al. Standards Track [Page 28] RFC 8532 Connectionless OAM YANG Data Model April 2019

             3.2.11 and 3.2.12 of RFC 8029 for details.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
      }
      case tunnel {
        leaf tunnel-interface {
          type uint32;
          description
            "Basic IPv4/IPv6 Tunnel ID.  See Sections 3.2.3
             and 3.2.4 of RFC 8029 for details.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures.";
        }
      }
      case pw {
        leaf remote-pe-address {
          type inet:ip-address;
          description
            "Remote PE address.  See Section 3.2.8
             of RFC 8029 for details.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
        leaf pw-id {
          type uint32;
          description
            "Pseudowire ID is a non-zero 32-bit ID.  See Sections
             3.2.8 and 3.2.9 of RFC 8029 for details.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
      }
      case vpls {
        leaf route-distinguisher {
          type rt:route-distinguisher;
          description
            "Route Distinguisher is an 8-octet identifier
             used to distinguish information about various
             L2VPNs advertised by a node.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }

Kumar, et al. Standards Track [Page 29] RFC 8532 Connectionless OAM YANG Data Model April 2019

        leaf sender-ve-id {
          type uint16;
          description
            "Sender's VE ID.  The VE ID (VPLS Edge Identifier)
             is a 2-octet identifier.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
        leaf receiver-ve-id {
          type uint16;
          description
            "Receiver's VE ID.  The VE ID (VPLS Edge Identifier)
             is a 2-octet identifier.";
          reference
            "RFC 8029: Detecting Multiprotocol Label
             Switched (MPLS) Data-Plane Failures";
        }
      }
      case mpls-mldp {
        choice root-address {
          description
            "Root address choice.";
          case ip-address {
            leaf source-address {
              type inet:ip-address;
              description
                "IP address.";
            }
            leaf group-ip-address {
              type inet:ip-address;
              description
                "Group IP address.";
            }
          }
          case vpn {
            leaf as-number {
              type inet:as-number;
              description
                "The AS number that identifies an Autonomous
                 System.";
            }
          }
          case global-id {
            leaf lsp-id {
              type string;
              description
                "LSP ID is an identifier of a LSP

Kumar, et al. Standards Track [Page 30] RFC 8532 Connectionless OAM YANG Data Model April 2019

                 within a MPLS network.";
              reference
                "RFC 8029: Detecting Multiprotocol Label
                 Switched (MPLS) Data-Plane Failures";
            }
          }
        }
      }
    }
    description
      "Test Point Attribute Container.";
  }
  container system-info {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:router-id-address-type')" {
      description
        "System ID address type.";
    }
    leaf router-id {
      type rt:router-id;
      description
        "Router ID assigned to this node.";
    }
    description
      "Router ID container.";
  }
  description
    "TP Address.";
}
grouping tp-address-ni {
  description
    "Test point address with VRF.";
  leaf ni {
    type routing-instance-ref;
    description
      "The ni is used to describe virtual resource partitioning
       that may be present on a network device.  An example of a
       common industry term for virtual resource partitioning is
       'VRF instance'.";
  }
  uses tp-address;
}
grouping connectionless-oam-tps {
  list oam-neighboring-tps {
    key "index";
    leaf index {

Kumar, et al. Standards Track [Page 31] RFC 8532 Connectionless OAM YANG Data Model April 2019

      type uint16 {
        range "0..65535";
      }
      description
        "Index of a list of neighboring test points
         in layers up and down the stack for
         the same interface that are related to the
         current test point.";
    }
    leaf position {
      type int8 {
        range "-1..1";
      }
      default "0";
      description
        "The position of the neighboring test point relative to
         the current test point.  Level 0 indicates a test point
         corresponding to a specific index in the same layer as
         the current test point.  -1 means there is a test point
         corresponding to a specific index in the test point down
         the stack, and +1 means there is a test point corresponding
         to a specific index in the test point up the stack.";
    }
    choice tp-location {
      case mac-address {
        leaf mac-address-location {
          type yang:mac-address;
          description
            "MAC address.";
        }
        description
          "MAC address based TP addressing.";
      }
      case ipv4-address {
        leaf ipv4-address-location {
          type inet:ipv4-address;
          description
            "IPv4 address.";
        }
        description
          "IP address based TP addressing.";
      }
      case ipv6-address {
        leaf ipv6-address-location {
          type inet:ipv6-address;
          description
            "IPv6 address.";
        }

Kumar, et al. Standards Track [Page 32] RFC 8532 Connectionless OAM YANG Data Model April 2019

        description
          "IPv6 address based TP addressing.";
      }
      case as-number {
        leaf as-number-location {
          type inet:as-number;
          description
            "AS number location.";
        }
        description
          "AS number for point-to-multipoint OAM.";
      }
      case router-id {
        leaf router-id-location {
          type rt:router-id;
          description
            "System ID location.";
        }
        description
          "System ID.";
      }
      description
        "TP location.";
    }
    description
      "List of neighboring test points in the same layer that are
       related to current test point.  If the neighboring test point
       is placed after the current test point, the position is
       specified as +1.  If the neighboring test point is placed
       before the current test point, the position is specified
       as -1; if no neighboring test points are placed before or
       after the current test point in the same layer, the
       position is specified as 0.";
  }
  description
    "List of neighboring test points related to connectionless OAM.";
}
grouping tp-technology {
  choice technology {
    default "technology-null";
    case technology-null {
      description
        "This is a placeholder when no technology is needed.";
      leaf tech-null {
        type empty;
        description
          "There is no technology to be defined.";

Kumar, et al. Standards Track [Page 33] RFC 8532 Connectionless OAM YANG Data Model April 2019

      }
    }
    description
      "Technology choice.";
  }
  description
    "OAM technology.";
}
grouping tp-tools {
  description
    "Test point OAM toolset.";
  container tp-tools {
    leaf continuity-check {
      type boolean;
      mandatory true;
      description
        "A flag indicating whether or not the
         Continuity Check function is supported.";
      reference
        "RFC 792: INTERNET CONTROL MESSAGE PROTOCOL
         RFC 4443: Internet Control Message Protocol (ICMPv6)
             for the Internet Protocol Version 6 (IPv6) Specification
         RFC 5880: Bidirectional Forwarding Detection
         RFC 5881: BFD for IPv4 and IPv6
         RFC 5883: BFD for Multihop Paths
         RFC 5884: BFD for MPLS Label Switched Paths
         RFC 5885: BFD for PW VCCV
         RFC 6450: Multicast Ping Protocol
         RFC 8029: Detecting Multiprotocol Label Switched (MPLS)
             Data-Plane Failures";
    }
    leaf path-discovery {
      type boolean;
      mandatory true;
      description
        "A flag indicating whether or not the
         path discovery function is supported.";
      reference
        "RFC 792: INTERNET CONTROL MESSAGE PROTOCOL
         RFC 4443: Internet Control Message Protocol (ICMPv6)
             for the Internet Protocol Version 6 (IPv6) Specification
         RFC 4884: Extended ICMP to Support Multi-Part Messages
         RFC 5837: Extending ICMP for Interface and Next-Hop
             Identification
         RFC 8029: Detecting Multiprotocol Label Switched (MPLS)
             Data-Plane Failures";
    }

Kumar, et al. Standards Track [Page 34] RFC 8532 Connectionless OAM YANG Data Model April 2019

    description
      "Container for test point OAM toolset.";
  }
}
grouping test-point-location-info {
  uses tp-technology;
  uses tp-tools;
  anydata root {
    yangmnt:mount-point "root";
    description
      "Root for models supported per test point.";
  }
  uses connectionless-oam-tps;
  description
    "Test point location.";
}
grouping test-point-locations {
  description
    "Group of test point locations.";
  leaf tp-location-type {
    type identityref {
      base tp-address-technology-type;
    }
    description
      "Test point location type.";
  }
  container ipv4-location-type {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:ipv4-address-type')" {
      description
        "When test point location type is equal to IPv4 address.";
    }
    container test-point-ipv4-location-list {
      list test-point-locations {
        key "ipv4-location ni";
        leaf ipv4-location {
          type inet:ipv4-address;
          description
            "IPv4 address.";
        }
        leaf ni {
          type routing-instance-ref;
          description
            "The ni is used to describe the
             corresponding network instance";
        }

Kumar, et al. Standards Track [Page 35] RFC 8532 Connectionless OAM YANG Data Model April 2019

        uses test-point-location-info;
        description
          "List of test point locations.";
      }
      description
        "Serves as top-level container
         for test point location list.";
    }
    description
      "Container for IPv4 location types.";
  }
  container ipv6-location-type {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:ipv6-address-type')" {
      description
        "When test point location is equal to IPv6 address.";
    }
    container test-point-ipv6-location-list {
      list test-point-locations {
        key "ipv6-location ni";
        leaf ipv6-location {
          type inet:ipv6-address;
          description
            "IPv6 address.";
        }
        leaf ni {
          type routing-instance-ref;
          description
            "The ni is used to describe the
             corresponding network instance.";
        }
        uses test-point-location-info;
        description
          "List of test point locations.";
      }
      description
        "Serves as top-level container
         for test point location list.";
    }
    description
      "ipv6 location type container.";
  }
  container mac-location-type {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:mac-address-type')" {
      description
        "When test point location type is equal to MAC address.";
    }

Kumar, et al. Standards Track [Page 36] RFC 8532 Connectionless OAM YANG Data Model April 2019

    container test-point-mac-address-location-list {
      list test-point-locations {
        key "mac-address-location";
        leaf mac-address-location {
          type yang:mac-address;
          description
            "MAC address.";
        }
        uses test-point-location-info;
        description
          "List of test point locations.";
      }
      description
        "Serves as top-level container
         for test point location list.";
    }
    description
      "Container for MAC address location types.";
  }
  container group-as-number-location-type {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:as-number-address-type')" {
      description
        "When test point location type is equal to AS number.";
    }
    container test-point-as-number-location-list {
      list test-point-locations {
        key "as-number-location";
        leaf as-number-location {
          type inet:as-number;
          description
            "AS number for point-to-multipoint OAM.";
        }
        leaf ni {
          type routing-instance-ref;
          description
            "The ni is used to describe the
             corresponding network instance.";
        }
        uses test-point-location-info;
        description
          "List of test point locations.";
      }
      description
        "Serves as top-level container
         for test point location list.";
    }
    description

Kumar, et al. Standards Track [Page 37] RFC 8532 Connectionless OAM YANG Data Model April 2019

      "Container for AS number location types.";
  }
  container group-router-id-location-type {
    when "derived-from-or-self(../tp-location-type,"
       + "'cl-oam:router-id-address-type')" {
      description
        "When test point location type is equal to system-info.";
    }
    container test-point-system-info-location-list {
      list test-point-locations {
        key "router-id-location";
        leaf router-id-location {
          type rt:router-id;
          description
            "System ID.";
        }
        leaf ni {
          type routing-instance-ref;
          description
            "The ni is used to describe the
             corresponding network instance.";
        }
        uses test-point-location-info;
        description
          "List of test point locations.";
      }
      description
        "Serves as top-level container for
         test point location list.";
    }
    description
      "Container for system ID location types.";
  }
}
augment "/nd:networks/nd:network/nd:node" {
  description
    "Augments the /networks/network/node path defined in the
     ietf-network module (RFC 8345) with test-point-locations
     grouping.";
  uses test-point-locations;
}
grouping timestamp {
  description
    "Grouping for timestamp.";
  leaf timestamp-type {
    type identityref {

Kumar, et al. Standards Track [Page 38] RFC 8532 Connectionless OAM YANG Data Model April 2019

      base lime:timestamp-type;
    }
    description
      "Type of timestamp, such as Truncated PTP or NTP.";
  }
  container timestamp-64bit {
    when "derived-from-or-self(../timestamp-type,"
       + "'lime:truncated-ptp')"
       + "or derived-from-or-self(../timestamp-type,"
       + "'lime:ntp64')" {
      description
        "Only applies when PTP truncated or 64-bit NTP timestamp.";
    }
    leaf timestamp-sec {
      type uint32;
      description
        "Absolute timestamp in seconds as per IEEE 1588v2
         or seconds part in 64-bit NTP timestamp.";
    }
    leaf timestamp-nanosec {
      type uint32;
      description
        "Fractional part in nanoseconds as per IEEE 1588v2
         or fractional part in 64-bit NTP timestamp.";
    }
    description
      "Container for 64-bit timestamp.  The Network Time Protocol
       (NTP) 64-bit timestamp format is defined in RFC 5905.  The
       PTP truncated timestamp format is defined in IEEE 1588v1.";
    reference
      "RFC 5905: Network Time Protocol Version 4: Protocol and
           Algorithms Specification
       IEEE 1588v1: IEEE Standard for a Precision Clock
           Synchronization Protocol for Networked Measurement and
           Control Systems Version 1";
  }
  container timestamp-80bit {
    when "derived-from-or-self(../timestamp-type, 'lime:ptp80')" {
      description
        "Only applies when 80-bit PTP timestamp.";
    }
    if-feature "ptp-long-format";
    leaf timestamp-sec {
      type uint64 {
        range "0..281474976710655";
      }
      description
        "48-bit timestamp in seconds as per IEEE 1588v2.";

Kumar, et al. Standards Track [Page 39] RFC 8532 Connectionless OAM YANG Data Model April 2019

    }
    leaf timestamp-nanosec {
      type uint32;
      description
        "Fractional part in nanoseconds as per IEEE 1588v2.";
    }
    description
      "Container for 80-bit timestamp.";
  }
  container ntp-timestamp-32bit {
    when "derived-from-or-self(../timestamp-type,"
       + "'lime:truncated-ntp')" {
      description
        "Only applies when 32-bit NTP short-format timestamp.";
    }
    if-feature "ntp-short-format";
    leaf timestamp-sec {
      type uint16;
      description
        "Timestamp in seconds as per short-format NTP.";
    }
    leaf timestamp-nanosec {
      type uint16;
      description
        "Truncated fractional part in 16-bit NTP timestamp.";
    }
    description
      "Container for 32-bit timestamp RFC5905.";
    reference
      "RFC 5905: Network Time Protocol Version 4: Protocol and
       Algorithms Specification.";
  }
  container icmp-timestamp-32bit {
    when "derived-from-or-self(../timestamp-type, 'lime:icmp')" {
      description
        "Only applies when ICMP timestamp.";
    }
    if-feature "icmp-timestamp";
    leaf timestamp-millisec {
      type uint32;
      description
        "Timestamp in milliseconds for ICMP timestamp.";
    }
    description
      "Container for 32-bit timestamp.  See RFC 792 for ICMP
       timestamp format.";
  }
}

Kumar, et al. Standards Track [Page 40] RFC 8532 Connectionless OAM YANG Data Model April 2019

grouping path-discovery-data {
  description
    "Data output from nodes related to path discovery.";
  container src-test-point {
    description
      "Source test point.";
    uses tp-address-ni;
  }
  container dest-test-point {
    description
      "Destination test point.";
    uses tp-address-ni;
  }
  leaf sequence-number {
    type uint64;
    default "0";
    description
      "Sequence number in data packets.  A value of
       zero indicates that no sequence number is sent.";
  }
  leaf hop-cnt {
    type uint8;
    default "0";
    description
      "Hop count.  A value of zero indicates
       that no hop count is sent.";
  }
  uses session-packet-statistics;
  uses session-error-statistics;
  uses session-delay-statistics;
  uses session-jitter-statistics;
  container path-verification {
    description
      "Optional information related to path verification.";
    leaf flow-info {
      type string;
      description
        "Information that refers to the flow.";
    }
    uses session-path-verification-statistics;
  }
  container path-trace-info {
    description
      "Optional per-hop path trace information about test points.
       The path trace information list typically has a single
       element for per-hop cases such as path-discovery RPC operation
       but allows a list of hop-related information for other types of
       data retrieval methods.";

Kumar, et al. Standards Track [Page 41] RFC 8532 Connectionless OAM YANG Data Model April 2019

    list path-trace-info-list {
      key "index";
      description
        "Path trace information list.";
      leaf index {
        type uint32;
        description
          "Trace information index.";
      }
      uses tp-address-ni;
      uses timestamp;
      leaf ingress-intf-name {
        type if:interface-ref;
        description
          "Ingress interface name.";
      }
      leaf egress-intf-name {
        type if:interface-ref;
        description
          "Egress interface name.";
      }
      leaf queue-depth {
        type uint32;
        description
          "Length of the queue of the interface from where
           the packet is forwarded out.  The queue depth could
           be the current number of memory buffers used by the
           queue, and a packet can consume one or more memory buffers,
           thus constituting device-level information.";
      }
      leaf transit-delay {
        type uint32;
        description
          "Time in nanoseconds that the packet spent transiting a
           node.";
      }
      leaf app-meta-data {
        type uint64;
        description
          "Application-specific data added by node.";
      }
    }
  }
}
grouping continuity-check-data {
  description
    "Continuity Check data output from nodes.";

Kumar, et al. Standards Track [Page 42] RFC 8532 Connectionless OAM YANG Data Model April 2019

  container src-test-point {
    description
      "Source test point.";
    uses tp-address-ni;
    leaf egress-intf-name {
      type if:interface-ref;
      description
        "Egress interface name.";
    }
  }
  container dest-test-point {
    description
      "Destination test point.";
    uses tp-address-ni;
    leaf ingress-intf-name {
      type if:interface-ref;
      description
        "Ingress interface name.";
    }
  }
  leaf sequence-number {
    type uint64;
    default "0";
    description
      "Sequence number in data packets.  A value of
       zero indicates that no sequence number is sent.";
  }
  leaf hop-cnt {
    type uint8;
    default "0";
    description
      "Hop count.  A value of zero indicates
       that no hop count is sent.";
  }
  uses session-packet-statistics;
  uses session-error-statistics;
  uses session-delay-statistics;
  uses session-jitter-statistics;
}
container cc-session-statistics-data {
  if-feature "continuity-check";
  config false;
  list cc-session-statistics {
    key "type";
    leaf type {
      type identityref {
        base traffic-type;

Kumar, et al. Standards Track [Page 43] RFC 8532 Connectionless OAM YANG Data Model April 2019

      }
      description
        "Type of traffic.";
    }
    container cc-ipv4-sessions-statistics {
      when "../type = 'ipv4'" {
        description
          "Only applies when traffic type is IPv4.";
      }
      description
        "CC ipv4 sessions.";
      uses cc-session-statistics;
    }
    container cc-ipv6-sessions-statistics {
      when "../type = 'ipv6'" {
        description
          "Only applies when traffic type is IPv6.";
      }
      description
        "CC IPv6 sessions.";
      uses cc-session-statistics;
    }
    description
      "List of CC session statistics data.";
  }
  description
    "CC operational information.";
}

}

 <CODE ENDS>

6. Connectionless Model Applicability

 The "ietf-connectionless-oam" module defined in this document
 provides a technology-independent abstraction of key OAM constructs
 for OAM protocols that use connectionless communication.  This module
 can be further extended to include technology-specific details, e.g.,
 adding new data nodes with technology-specific functions and
 parameters into proper anchor points of the base model, so as to
 develop a technology-specific connectionless OAM model.
 This section demonstrates the usability of the connectionless YANG
 OAM data model to various connectionless OAM technologies, e.g., BFD
 and LSP ping.  Note that, in this section, several snippets of
 technology-specific model extensions are presented for illustrative
 purposes.  The complete model extensions should be worked on in the
 working groups of the respective protocols.

Kumar, et al. Standards Track [Page 44] RFC 8532 Connectionless OAM YANG Data Model April 2019

6.1. BFD Extension

 RFC 7276 defines BFD as a connection-oriented protocol.  It is used
 to monitor a connectionless protocol in the case of basic BFD for IP.

6.1.1. Augment Method

 The following sections show how the "ietf-connectionless-oam" module
 can be extended to cover BFD technology.  For this purpose, a set of
 extensions are introduced such as the technology-type extension and
 test-point attributes extension.
 Note that a dedicated BFD YANG data model [BFD-YANG] is also
 standardized.  Augmentation of the "ietf-connectionless-oam" module
 with BFD-specific details provides an alternative approach with a
 unified view of management information across various OAM protocols.
 The BFD-specific details can be the grouping defined in the BFD
 model, thereby avoiding duplication of effort.

6.1.1.1. Technology-Type Extension

 No BFD technology type has been defined in the "ietf-connectionless-
 oam" module.  Therefore, a technology-type extension is required in
 the module extension.
 The snippet below depicts an example of adding the "bfd" type as an
 augment to the "ietf-connectionless-oam" module:
 augment "/nd:networks/nd:network/nd:node/"
 +"coam:location-type/coam:ipv4-location-type"
 +"/coam:test-point-ipv4-location-list/"
 +"coam:test-point-locations/coam:technology"
 {
     leaf bfd{
    type string;
   }
 }

6.1.1.2. Test Point Attributes Extension

 To support BFD, the "ietf-connectionless-oam" module can be extended
 by adding specific parameters into the "test-point-locations" list
 and/or adding a new location type such as "BFD over MPLS TE" under
 "location-type".

Kumar, et al. Standards Track [Page 45] RFC 8532 Connectionless OAM YANG Data Model April 2019

6.1.1.2.1. Define and Insert New Nodes into Corresponding test-point-

          location
 In the "ietf-connectionless-oam" module, multiple "test-point-
 location" lists are defined under the "location-type" choice node.
 Therefore, to derive a model for some BFD technologies (such as IP
 single-hop, IP multihop, etc.), data nodes for BFD-specific details
 need to be added to the corresponding "test-point-locations" list.
 In this section, some groupings that are defined in [BFD-YANG] are
 reused as follows.
 The snippet below shows how the "ietf-connectionless-oam" module can
 be extended to support "BFD IP Single-Hop":
 augment "/nd:networks/nd:network/nd:node/"
 +"coam:location-type/coam:ipv4-location-type"
 +"/coam:test-point-ipv4-location-list/"
         +"coam:test-point-locations"
 {
         container session-cfg {
           description "BFD IP single-hop session configuration";
           list sessions {
             key "interface dest-addr";
             description "List of IP single-hop sessions";
             leaf interface {
               type if:interface-ref;
               description
                 "Interface on which the BFD session is running.";
             }
             leaf dest-addr {
               type inet:ip-address;
               description "IP address of the peer";
             }
             uses bfd:bfd-grouping-common-cfg-parms;
             uses bfd:bfd-grouping-echo-cfg-parms;
           }
         }
 }
 Similar augmentations can be defined to support other BFD
 technologies such as BFD IP Multihop, BFD over MPLS, etc.

Kumar, et al. Standards Track [Page 46] RFC 8532 Connectionless OAM YANG Data Model April 2019

6.1.1.2.2. Add New location-type Cases

 In the "ietf-connectionless-oam" module, If there is no appropriate
 "location-type" case that can be extended, a new "location-type" case
 can be defined and inserted into the "location-type" choice node.
 Therefore, there is flexibility -- the module user can add "location-
 type" to support other types of test point that are not defined in
 the "ietf-connectionless-oam" module.  In this section, a new
 "location-type" case is added, and some groupings that are defined in
 [BFD-YANG] are reused as follows.
 The snippet below shows how the "ietf-connectionless-oam" module can
 be extended to support "BFD over MPLS-TE":
 augment "/nd:networks/nd:network/nd:node/coam:location-type"{
  case te-location{
   list test-point-location-list{
    key "tunnel-name";
    leaf tunnel-name{
     type leafref{
  path "/te:te/te:tunnels/te:tunnel/te:name";
 }
 description
 "Point to a TE instance.";
    }
     uses bfd:bfd-grouping-common-cfg-parms;
         uses bfd-mpls:bfd-encap-cfg;
   }
  }
 }
 Similar augmentations can be defined to support other BFD
 technologies such as BFD over LAG, etc.

6.1.2. Schema Mount

 An alternative method is using the schema mount mechanism [RFC8528]
 in the "ietf-connectionless-oam" module.  Within the "test-point-
 locations" list, a "root" attribute is defined to provide a mount
 point for models that will be added onto per "test-point-locations".
 Therefore, the "ietf-connectionless-oam" module can provide a place
 in the node hierarchy where other OAM YANG data models can be
 attached, without any special extension in the "ietf-connectionless-
 oam" YANG data module [RFC8528].  Note that the limitation of the
 schema mount method is that it's not allowed to specify certain
 modules that are required to be mounted under a mount point.

Kumar, et al. Standards Track [Page 47] RFC 8532 Connectionless OAM YANG Data Model April 2019

 The snippet below depicts the definition of the "root" attribute.
       anydata root {
        yangmnt:mount-point root;
        description
          "Root for models that are supported per test point";
       }
 The following section shows how the "ietf-connectionless-oam" module
 can use schema mount to support BFD technology.

6.1.2.1. BFD Modules Might Be Populated in schema-mounts

 To support BFD technology, "ietf-bfd-ip-sh" and "ietf-bfd-ip-mh" YANG
 modules might be populated in the "schema-mounts" container:
    <schema-mounts
        xmlns="urn:ietf:params:xml:ns:yang:ietf-yang-schema-mount">
      <mount-point>
        <module> ietf-connectionless-oam </module>
        <name>root</name>
        <use-schema>
          <name>root</name>
        </use-schema>
      </mount-point>
      <schema>
        <name>root</name>
        <module>
          <name>ietf-bfd-ip-sh </name>
          <revision>2016-07-04</revision>
          <namespace>
            urn:ietf:params:xml:ns:yang:ietf-bfd-ip-sh
          </namespace>
          <conformance-type>implement</conformance-type>
        </module>
        <module>
          <name>ietf-bfd-ip-mh</name>
          <revision> 2016-07-04</revision>
          <namespace>
            urn:ietf:params:xml:ns:yang:ietf-bfd-ip-mh
          </namespace>
          <conformance-type>implement</conformance-type>
        </module>
      </schema>
    </schema-mounts>

Kumar, et al. Standards Track [Page 48] RFC 8532 Connectionless OAM YANG Data Model April 2019

 and the "ietf-connectionless-oam" module might have:
 <ietf-connectionless-oam
 uri="urn:ietf:params:xml:ns:yang:ietf-connectionless-oam">
    ......
  <test-point-locations>
   <ipv4-location>192.0.2.1</ipv4-location>
    ......
   <root>
    <ietf-bfd-ip-sh uri="urn:ietf:params:xml:ns:yang:ietf-bfd-ip-sh">
     <ip-sh>
      foo
      ......
     </ip-sh>
    </ietf-bfd-ip-sh>
    <ietf-bfd-ip-mh uri="urn:ietf:params:xml:ns:yang:ietf-bfd-ip-mh">
     <ip-mh>
      foo
      ......
     </ip-mh>
    </ietf-bfd-ip-mh>
   </root>
  </test-point-locations>
 </ietf-connectionless-oam>

6.2. LSP Ping Extension

6.2.1. Augment Method

 The following sections show how the "ietf-connectionless-oam" module
 can be extended to support LSP ping technology.  For this purpose, a
 set of extensions are introduced such as the "technology-type"
 extension and the test-point "attributes" extension.
 Note that an LSP Ping YANG data model is being specified
 [LSP-PING-YANG].  As with BFD, users can choose to use the
 "ietf-connectionless-oam" as the basis and augment the
 "ietf-connectionless-oam" model with details specific to LSP Ping in
 the model extension to provide a unified view across different
 technologies.  The details that are specific to LSP Ping can be the
 grouping defined in the LSP ping model to avoid duplication of
 effort.

6.2.1.1. Technology-Type Extension

 No LSP Ping technology type has been defined in the
 "ietf-connectionless-oam" module.  Therefore, a technology-type
 extension is required in the module extension.

Kumar, et al. Standards Track [Page 49] RFC 8532 Connectionless OAM YANG Data Model April 2019

 The snippet below depicts an example of augmenting
 "ietf-connectionless-oam" with "lsp-ping" type:
 augment "/nd:networks/nd:network/nd:node/"
 +"coam:location-type/coam:ipv4-location-type"
 +"/coam:test-point-ipv4-location-list/"
         +"coam:test-point-locations/coam:technology"
 {
    leaf lsp-ping{
    type string;
   }
 }

6.2.1.2. Test Point Attributes Extension

 To support LSP Ping, the "ietf-connectionless-oam" module can be
 extended and parameters specific to LSP Ping can be defined and put
 on the "test-point-locations" list.
 Users can reuse the attributes or groupings that are defined in
 [LSP-PING-YANG] as follows:
 The snippet below depicts an example of augmenting the "test-point-
 locations" list with LSP Ping attributes:
 augment "/nd:networks/nd:network/nd:node/"
 +"coam:location-type/coam:ipv4-location-type"
 +"/coam:test-point-ipv4-location-list/"
         +"coam:test-point-locations"
 {
 list lsp-ping {
          key "lsp-ping-name";
          leaf lsp-ping-name {
           type string {
             length "1..31";
          }
         mandatory "true";
         description "LSP Ping test name.";
         ......
       }

6.2.2. Schema Mount

 An alternative method is using the schema mount mechanism [RFC8528]
 in the "ietf-connectionless-oam" module.  Within the "test-point-
 locations" list, a "root" attribute is defined to provide a mounted
 point for models mounted per "test-point-locations".  Therefore, the
 "ietf-connectionless-oam" model can provide a place in the node

Kumar, et al. Standards Track [Page 50] RFC 8532 Connectionless OAM YANG Data Model April 2019

 hierarchy where other OAM YANG data models can be attached, without
 any special extension in the "ietf-connectionless-oam" YANG data
 module [RFC8528].  Note that the limitation of the schema mount
 method is that it's not allowed to specify certain modules that are
 required to be mounted under a mount point.
 The snippet below depicts the definition of "root" attribute.
       anydata root {
        yangmnt:mount-point root;
        description
       "Root for models supported per test point";
       }
 The following section shows how the "ietf-connectionless-oam" module
 can use schema mount to support LSP Ping technology.

6.2.2.1. LSP Ping Modules Might Be Populated in schema-mounts

 To support LSP Ping technology, the "ietf-lsp-ping" YANG module
 [LSP-PING-YANG] might be populated in the "schema-mounts" container:
    <schema-mounts
        xmlns="urn:ietf:params:xml:ns:yang:ietf-yang-schema-mount">
      <mount-point>
        <module> ietf-connectionless-oam </module>
        <name>root</name>
        <use-schema>
          <name>root</name>
        </use-schema>
      </mount-point>
      <schema>
        <name>root</name>
        <module>
          <name>ietf-lsp-ping </name>
          <revision>2016-03-18</revision>
          <namespace>
            urn:ietf:params:xml:ns:yang: ietf-lsp-ping
          </namespace>
          <conformance-type>implement</conformance-type>
        </module>
      </schema>
    </schema-mounts>

Kumar, et al. Standards Track [Page 51] RFC 8532 Connectionless OAM YANG Data Model April 2019

 and the "ietf-connectionless-oam" module might have:
 <ietf-connectionless-oam
 uri="urn:ietf:params:xml:ns:yang:ietf-connectionless-oam">
    ......
  <test-point-locations>
   <ipv4-location> 192.0.2.1</ipv4-location>
    ......
   <root>
    <ietf-lsp-ping uri="urn:ietf:params:xml:ns:yang:ietf-lsp-ping">
     <lsp-pings>
      foo
      ......
     </lsp-pings>
    </ietf-lsp-ping>
   </root>
  </test-point-locations>
 </ietf-connectionless-oam>

7. Security Considerations

 The YANG module specified in this document defines a schema for data
 that is designed to be accessed via network management protocols such
 as NETCONF [RFC6241] or RESTCONF [RFC8040].  The lowest NETCONF layer
 is the secure transport layer, and the mandatory-to-implement secure
 transport is Secure Shell (SSH) [RFC6242].  The lowest RESTCONF layer
 is HTTPS, and the mandatory-to-implement secure transport is TLS
 [RFC8446].
 The NETCONF Configuration Access Control Model (NACM) [RFC8341]
 provides the means to restrict access for particular NETCONF or
 RESTCONF users to a preconfigured subset of all available NETCONF or
 RESTCONF protocol operations and content.
 There are a number of data nodes defined in this YANG module that are
 writable/creatable/deletable (i.e., config true, which is the
 default).  These data nodes may be considered sensitive in some
 network environments.  Write operations (e.g., edit-config) to these
 data nodes without proper protection can have a negative effect on
 network operations.  These are the subtrees and data nodes and their
 sensitivity/vulnerability:
    /nd:networks/nd:network/nd:node/cl-oam:location-type/cl-oam:ipv4-
    location-type/cl-oam:test-point-ipv4-location-list/cl-oam:test-
    point-locations/

Kumar, et al. Standards Track [Page 52] RFC 8532 Connectionless OAM YANG Data Model April 2019

    /nd:networks/nd:network/nd:node/cl-oam:location-type/cl-oam:ipv6-
    location-type/cl-oam:test-point-ipv6-location-list/cl-oam:test-
    point-locations/
    /nd:networks/nd:network/nd:node/cl-oam:location-type/cl-oam:mac-
    location-type/cl-oam:test-point-mac-address-location-list/cl-
    oam:test-point-locations/
    /nd:networks/nd:network/nd:node/cl-oam:location-type/cl-oam:group-
    as-number-location-type/cl-oam:test-point-as-number-location-list/
    cl-oam:test-point-locations/
    /nd:networks/nd:network/nd:node/cl-oam:location-type/cl-oam:group-
    router-id-location-type/cl-oam:test-point-system-info-location-
    list/cl-oam:test-point-locations/
 Unauthorized access to any of these lists can adversely affect OAM
 management system handling of end-to-end OAM and coordination of OAM
 within underlying network layers.  This may lead to inconsistent
 configuration, reporting, and presentation for the OAM mechanisms
 used to manage the network.
 Some of the readable data nodes in this YANG module may be considered
 sensitive or vulnerable in some network environments.  It is thus
 important to control read access (e.g., via get, get-config, or
 notification) to these data nodes.  These are the subtrees and data
 nodes and their sensitivity/vulnerability:
    /coam:cc-session-statistics-data/cl-oam:cc-ipv4-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv4-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-up-count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv4-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-down-count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv4-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-admin-down-
    count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv6-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv6-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-up-count//

Kumar, et al. Standards Track [Page 53] RFC 8532 Connectionless OAM YANG Data Model April 2019

    /coam:cc-session-statistics-data/cl-oam:cc-ipv6-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-down-count/
    /coam:cc-session-statistics-data/cl-oam:cc-ipv6-sessions-
    statistics/cl-oam:cc-session-statistics/cl-oam:session-admin-down-
    count/

8. IANA Considerations

 This document registers URIs in the "IETF XML Registry" [RFC3688].
 Following the format in [RFC3688], the following registrations have
 been made.
    URI: urn:ietf:params:xml:ns:yang:ietf-lime-time-types
    Registrant Contact: The IESG.
    XML: N/A; the requested URI is an XML namespace.
    URI: urn:ietf:params:xml:ns:yang:ietf-connectionless-oam
    Registrant Contact: The IESG.
    XML: N/A; the requested URI is an XML namespace.
 This document registers two YANG modules in the "YANG Module Names"
 registry [RFC6020].
    Name: ietf-lime-time-types
    Namespace: urn:ietf:params:xml:ns:yang:ietf-lime-time-types
    Prefix: lime
    Reference: RFC 8532
    Name: ietf-connectionless-oam
    Namespace: urn:ietf:params:xml:ns:yang:ietf-connectionless-oam
    Prefix: cl-oam
    Reference: RFC 8532

9. References

9.1. Normative References

 [RFC792]   Postel, J., "Internet Control Message Protocol", RFC 792,
            September 1981.
 [RFC1831]  Srinivasan, R., "RPC: Remote Procedure Call Protocol
            Specification Version 2", RFC 1831, DOI 10.17487/RFC1831,
            August 1995, <https://www.rfc-editor.org/info/rfc1831>.
 [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
            DOI 10.17487/RFC3688, January 2004,
            <https://www.rfc-editor.org/info/rfc3688>.

Kumar, et al. Standards Track [Page 54] RFC 8532 Connectionless OAM YANG Data Model April 2019

 [RFC4382]  Nadeau, T., Ed. and H. van der Linde, Ed., "MPLS/BGP Layer
            3 Virtual Private Network (VPN) Management Information
            Base", RFC 4382, DOI 10.17487/RFC4382, February 2006,
            <https://www.rfc-editor.org/info/rfc4382>.
 [RFC4443]  Conta, A., Deering, S., and M. Gupta, Ed., "Internet
            Control Message Protocol (ICMPv6) for the Internet
            Protocol Version 6 (IPv6) Specification", STD 89,
            RFC 4443, DOI 10.17487/RFC4443, March 2006,
            <https://www.rfc-editor.org/info/rfc4443>.
 [RFC4656]  Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and
            M. Zekauskas, "A One-way Active Measurement Protocol
            (OWAMP)", RFC 4656, DOI 10.17487/RFC4656, September 2006,
            <https://www.rfc-editor.org/info/rfc4656>.
 [RFC5357]  Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and
            J. Babiarz, "A Two-Way Active Measurement Protocol
            (TWAMP)", RFC 5357, DOI 10.17487/RFC5357, October 2008,
            <https://www.rfc-editor.org/info/rfc5357>.
 [RFC5880]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
            (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
            <https://www.rfc-editor.org/info/rfc5880>.
 [RFC5905]  Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
            "Network Time Protocol Version 4: Protocol and Algorithms
            Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
            <https://www.rfc-editor.org/info/rfc5905>.
 [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
            and A. Bierman, Ed., "Network Configuration Protocol
            (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
            <https://www.rfc-editor.org/info/rfc6241>.
 [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
            Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
            <https://www.rfc-editor.org/info/rfc6242>.
 [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
            RFC 6991, DOI 10.17487/RFC6991, July 2013,
            <https://www.rfc-editor.org/info/rfc6991>.
 [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
            RFC 7950, DOI 10.17487/RFC7950, August 2016,
            <https://www.rfc-editor.org/info/rfc7950>.

Kumar, et al. Standards Track [Page 55] RFC 8532 Connectionless OAM YANG Data Model April 2019

 [RFC8029]  Kompella, K., Swallow, G., Pignataro, C., Ed., Kumar, N.,
            Aldrin, S., and M. Chen, "Detecting Multiprotocol Label
            Switched (MPLS) Data-Plane Failures", RFC 8029,
            DOI 10.17487/RFC8029, March 2017,
            <https://www.rfc-editor.org/info/rfc8029>.
 [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
            Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
            <https://www.rfc-editor.org/info/rfc8040>.
 [RFC8294]  Liu, X., Qu, Y., Lindem, A., Hopps, C., and L. Berger,
            "Common YANG Data Types for the Routing Area", RFC 8294,
            DOI 10.17487/RFC8294, December 2017,
            <https://www.rfc-editor.org/info/rfc8294>.
 [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
            Access Control Model", STD 91, RFC 8341,
            DOI 10.17487/RFC8341, March 2018,
            <https://www.rfc-editor.org/info/rfc8341>.
 [RFC8343]  Bjorklund, M., "A YANG Data Model for Interface
            Management", RFC 8343, DOI 10.17487/RFC8343, March 2018,
            <https://www.rfc-editor.org/info/rfc8343>.
 [RFC8345]  Clemm, A., Medved, J., Varga, R., Bahadur, N.,
            Ananthakrishnan, H., and X. Liu, "A YANG Data Model for
            Network Topologies", RFC 8345, DOI 10.17487/RFC8345, March
            2018, <https://www.rfc-editor.org/info/rfc8345>.
 [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
            Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
            <https://www.rfc-editor.org/info/rfc8446>.
 [RFC8529]  Berger, L., Hopps, C., Lindem, A., Bogdanovic, D., and
            X. Liu, "YANG Model for Network Instances", RFC 8529,
            DOI 10.17487/RFC8529, March 2019,
            <https://www.rfc-editor.org/info/rfc8529>.

9.2. Informative References

 [BFD-YANG] Rahman, R., Zheng, L., Jethanandani, M., Networks, J., and
            G. Mirsky, "YANG Data Model for Bidirectional Forwarding
            Detection (BFD)", Work in Progress, draft-ietf-bfd-yang-
            17, August 2018.
 [G.800]    "Unified functional architecture of transport networks",
            ITU-T Recommendation G.800, 2016.

Kumar, et al. Standards Track [Page 56] RFC 8532 Connectionless OAM YANG Data Model April 2019

 [G.8013]   "OAM functions and mechanisms for Ethernet based
            networks", ITU-T Recommendation G.8013/Y.1731, 2013.
 [IEEE.1588v1]
            "IEEE Standard for a Precision Clock Synchronization
            Protocol for Networked Measurement and Control Systems
            Version 1", IEEE Std 1588, 2002.
 [IEEE.1588v2]
            "IEEE Standard for a Precision Clock Synchronization
            Protocol for Networked Measurement and Control Systems
            Version 2", IEEE Std 1588, 2008.
 [LSP-PING-YANG]
            Zheng, L., Zheng, G., Mirsky, G., Rahman, R., and F.
            Iqbal, "YANG Data Model for LSP-Ping", Work in Progress,
            draft-zheng-mpls-lsp-ping-yang-cfg-10, January 2019.
 [RFC5462]  Andersson, L. and R. Asati, "Multiprotocol Label Switching
            (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic
            Class" Field", RFC 5462, DOI 10.17487/RFC5462, February
            2009, <https://www.rfc-editor.org/info/rfc5462>.
 [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
            the Network Configuration Protocol (NETCONF)", RFC 6020,
            DOI 10.17487/RFC6020, October 2010,
            <https://www.rfc-editor.org/info/rfc6020>.
 [RFC6136]  Sajassi, A., Ed. and D. Mohan, Ed., "Layer 2 Virtual
            Private Network (L2VPN) Operations, Administration, and
            Maintenance (OAM) Requirements and Framework", RFC 6136,
            DOI 10.17487/RFC6136, March 2011,
            <https://www.rfc-editor.org/info/rfc6136>.
 [RFC7276]  Mizrahi, T., Sprecher, N., Bellagamba, E., and
            Y. Weingarten, "An Overview of Operations, Administration,
            and Maintenance (OAM) Tools", RFC 7276,
            DOI 10.17487/RFC7276, June 2014,
            <https://www.rfc-editor.org/info/rfc7276>.
 [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
            BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
            <https://www.rfc-editor.org/info/rfc8340>.
 [RFC8528]  Bjorklund, M. and L. Lhotka, "YANG Schema Mount",
            RFC 8528, DOI 10.17487/RFC8528, March 2019,
            <https://www.rfc-editor.org/info/rfc8528>.

Kumar, et al. Standards Track [Page 57] RFC 8532 Connectionless OAM YANG Data Model April 2019

 [RFC8531]  Kumar, D., Wu, Q., and M. Wang, "Generic YANG Data Model
            for Connection-Oriented Operations, Administration, and
            Maintenance (OAM) Protocols", RFC 8531,
            DOI 10.17487/RFC8531, April 2019,
            <https://www.rfc-editor.org/info/rfc8531>.
 [RFC8533]  Kumar, D., Wang, M., Wu, Q., Ed., Rahman, R., and
            S. Raghavan, " A YANG Data Model for Retrieval Methods for
            the Management of Operations, Administration, and
            Maintenance (OAM) Protocols That Use Connectionless
            Communications", RFC 8533, DOI 10.17487/RFC8533, April
            2019.

Acknowledgments

 The authors of this document would like to thank Elwyn Davies, Alia
 Atlas, Brian E. Carpenter, Greg Mirsky, Adam Roach, Alissa Cooper,
 Eric Rescorla, Ben Campbell, Benoit Claise, Kathleen Moriarty, Carlos
 Pignataro, and others for their substantive review and comments, and
 proposals to stabilize and improve the document.

Kumar, et al. Standards Track [Page 58] RFC 8532 Connectionless OAM YANG Data Model April 2019

Authors' Addresses

 Deepak Kumar
 CISCO Systems
 510 McCarthy Blvd
 Milpitas, CA  95035
 United States of America
 Email: dekumar@cisco.com
 Michael Wang
 Huawei Technologies, Co., Ltd
 101 Software Avenue, Yuhua District
 Nanjing  210012
 China
 Email: wangzitao@huawei.com
 Qin Wu (editor)
 Huawei
 101 Software Avenue, Yuhua District
 Nanjing, Jiangsu  210012
 China
 Email: bill.wu@huawei.com
 Reshad Rahman
 Cisco Systems
 2000 Innovation Drive
 Kanata, Ontario  K2K 3E8
 Canada
 Email: rrahman@cisco.com
 Srihari Raghavan
 Cisco Systems
 Tril Infopark Sez, Ramanujan IT City
 Neville Block, 2nd floor, Old Mahabalipuram Road
 Chennai, Tamil Nadu  600113
 India
 Email: srihari@cisco.com

Kumar, et al. Standards Track [Page 59]

/data/webs/external/dokuwiki/data/pages/rfc/rfc8532.txt · Last modified: 2019/04/17 01:26 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki