GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc8207

Internet Engineering Task Force (IETF) R. Bush Request for Comments: 8207 Internet Initiative Japan BCP: 211 September 2017 Category: Best Current Practice ISSN: 2070-1721

                 BGPsec Operational Considerations

Abstract

 Deployment of the BGPsec architecture and protocols has many
 operational considerations.  This document attempts to collect and
 present the most critical and universal.  Operational practices are
 expected to evolve as BGPsec is formalized and initially deployed.

Status of This Memo

 This memo documents an Internet Best Current Practice.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 BCPs is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc8207.

Copyright Notice

 Copyright (c) 2017 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Bush Best Current Practice [Page 1] RFC 8207 BGPsec Operational Considerations September 2017

Table of Contents

 1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
 2.  Suggested Reading . . . . . . . . . . . . . . . . . . . . . .   3
 3.  RPKI Distribution and Maintenance . . . . . . . . . . . . . .   3
 4.  AS/Router Certificates  . . . . . . . . . . . . . . . . . . .   3
 5.  Within a Network  . . . . . . . . . . . . . . . . . . . . . .   4
 6.  Considerations for Edge Sites . . . . . . . . . . . . . . . .   4
 7.  Routing Policy  . . . . . . . . . . . . . . . . . . . . . . .   5
 8.  Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . .   7
 9.  Security Considerations . . . . . . . . . . . . . . . . . . .   7
 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . .   7
 11. References  . . . . . . . . . . . . . . . . . . . . . . . . .   8
   11.1.  Normative References . . . . . . . . . . . . . . . . . .   8
   11.2.  Informative References . . . . . . . . . . . . . . . . .   8
 Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . .  10
 Author's Address  . . . . . . . . . . . . . . . . . . . . . . . .  10

1. Introduction

 Origin validation based on the Resource Public Key Infrastructure
 (RPKI) [RFC6811] is in its early phases.  As BGPsec [RFC8205] may
 require larger memory and/or more modern CPUs, it expected to be
 deployed incrementally over a longer time span.  BGPsec is a new
 protocol with many operational considerations that this document
 attempts to describe.  As with most operational practices, they will
 likely change over time.
 BGPsec relies on widespread propagation of the RPKI [RFC6480].  How
 the RPKI is distributed and maintained globally and within an
 operator's infrastructure may be different for BGPsec than for origin
 validation.
 BGPsec needs to be spoken only by an Autonomous System's (AS's)
 eBGP-speaking border routers.  It is designed so that it can be used
 to protect announcements that are originated by resource-constrained
 edge routers.  This has special operational considerations, see
 Section 6.
 Different prefixes may have different timing and replay protection
 considerations.

Bush Best Current Practice [Page 2] RFC 8207 BGPsec Operational Considerations September 2017

1.1. Requirements Language

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
 "OPTIONAL" in this document are to be interpreted as described in
 BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
 capitals, as shown here.

2. Suggested Reading

 It is assumed that the reader understands BGP [RFC4271], BGPsec
 [RFC8205], the RPKI [RFC6480], the RPKI Repository Structure
 [RFC6481], and Route Origin Authorizations (ROAs) [RFC6482].

3. RPKI Distribution and Maintenance

 The considerations for RPKI objects (Certificates, Certificate
 Revocation Lists (CRLs), manifests [RFC6481], and Ghostbusters
 Records [RFC6493]), Trust Anchor Locators (TALs) [RFC7730], cache
 behaviors of synchronization, and validation from the section on RPKI
 Distribution and Maintenance of [RFC7115] apply.  Specific
 considerations relating to ROA objects do not apply to this document.

4. AS/Router Certificates

 As described in [KEY], BGPsec-speaking routers are capable of
 generating their own public/private key-pairs and having their
 certificates signed and published in the RPKI by the RPKI
 Certification Authority (CA) system, and/or are given public/private
 key-pairs by the operator.
 A site/operator may use a single certificate/key in all their
 routers, one certificate/key per router, or any granularity in
 between.
 A large operator, concerned that a compromise of one router's key
 would make other routers vulnerable, may deploy a more complex
 certificate/key distribution burden to reduce this exposure.
 At the other end of the spectrum, an edge site with one or two
 routers may choose to use a single certificate/key.
 In anticipation of possible key compromise, a prudent operator SHOULD
 pre-provision each router's 'next' key in the RPKI so that there is
 no propagation delay for provisioning the new key.

Bush Best Current Practice [Page 3] RFC 8207 BGPsec Operational Considerations September 2017

5. Within a Network

 BGPsec is spoken by edge routers in a network, specifically those
 that border other networks/ASes.
 In an AS where edge routers speak BGPsec and, therefore, inject
 BGPsec paths into the iBGP (internal BGP), Route Reflectors (RRs)
 MUST have BGPsec enabled if and only if there are eBGP (external BGP)
 speakers in their client cone, i.e., an RR client or the transitive
 closure of a client's customers.
 A BGPsec-capable router MAY use the data it receives to influence
 local policy within its network, see Section 7.  In deployment, this
 policy should fit into the AS's existing policy, preferences, etc.
 This allows a network to incrementally deploy BGPsec-enabled border
 routers.
 eBGP speakers that face more critical peers or upstreams or
 downstreams would be candidates for early deployment.  Both securing
 one's own announcements and validating received announcements should
 be considered in partial deployment.
 An operator should be aware that BGPsec, as any other policy change,
 can cause traffic shifts in their network.  And, as with normal
 policy shift practice, a prudent operator has the tools and methods
 to predict, measure, modify, etc.
 On the other hand, an operator wanting to monitor router loading,
 shifts in traffic, etc., might deploy incrementally while watching
 those and similar effects.
 BGPsec does not sign over communities, so they are not formally
 trustable.  Additionally, outsourcing verification is not a prudent
 security practice.  Therefore, an eBGP listener SHOULD NOT strongly
 trust unsigned security signaling, such as communities, received
 across a trust boundary.

6. Considerations for Edge Sites

 An edge site that does not provide transit and trusts its upstream(s)
 may only originate a signed prefix announcement and not validate
 received announcements.
 An operator might need to use hardware with limited resources.  In
 such cases, BGPsec protocol capability negotiation allows for a
 resource-constrained edge router to hold only its own signing key(s)
 and sign its announcements, but not receive signed announcements.

Bush Best Current Practice [Page 4] RFC 8207 BGPsec Operational Considerations September 2017

 Therefore, the router would not have to deal with the majority of the
 RPKI, potentially saving the need for additional hardware.
 As the vast majority of ASes are stubs, and they announce the
 majority of prefixes, this allows for simpler and less expensive
 incremental deployment.  It may also mean that edge sites concerned
 with routing security will be attracted to upstreams that support
 BGPsec.

7. Routing Policy

 As BGPsec-signed paths cannot traverse non-BGPsec topology, partial
 BGPsec deployment forms islands of assured paths.  As islands grow to
 touch each other, they become larger islands.
 Unlike origin validation based on the RPKI, BGPsec marks a received
 announcement as Valid or Not Valid, there is no explicit NotFound
 state.  In some sense, an unsigned BGP4 path is the equivalent of
 NotFound.  How this is used in routing is up to the operator's local
 policy, similar to origin validation as in [RFC6811].
 As BGPsec will be rolled out over years and does not allow for
 intermediate non-signing edge routers, coverage will be spotty for a
 long time.  This presents a dilemma; should a router evaluating an
 inbound BGPsec_PATH as Not Valid be very strict and discard it?  On
 the other hand, it might be the only path to that prefix, and a very
 low local-preference would cause it to be used and propagated only if
 there was no alternative.  Either choice is reasonable, but we
 recommend dropping because of the next point.
 Operators should be aware that accepting Not Valid announcements, no
 matter the local preference, will often be the equivalent of treating
 them as fully Valid.  Local preference affects only routes to the
 same set of destinations.  Consider having a Valid announcement from
 neighbor V for prefix 10.0.0.0/16 and a Not Valid announcement for
 10.0.666.0/24 from neighbor I.  If local policy on the router is not
 configured to discard the Not Valid announcement from I, then the
 longest match forwarding will send packets to neighbor I no matter
 the value of local preference.
 Validation of signed paths is usually deployed at the eBGP edge.
 Local policy on the eBGP edge MAY convey the validation state of a
 BGP-signed path through normal local policy mechanisms, e.g., setting
 a BGP community for internal use, or modifying a metric value such as
 local-preference or Multi-Exit Discriminator (MED).  Some may choose

Bush Best Current Practice [Page 5] RFC 8207 BGPsec Operational Considerations September 2017

 to use the large Local-Pref hammer.  Others may choose to let AS path
 rule and set their internal metric, which comes after AS path in the
 BGP decision process.
 As the mildly stochastic timing of RPKI propagation may cause version
 skew across routers, an AS Path that does not validate at router R0
 might validate at R1.  Therefore, signed paths that are Not Valid and
 yet propagated (because they are chosen as best path) MUST NOT have
 signatures stripped and MUST be signed if sent to external BGPsec
 speakers.
 This implies that updates which a speaker judges to be Not Valid MAY
 be propagated to iBGP peers.  Therefore, unless local policy ensures
 otherwise, a signed path learned via iBGP may be Not Valid.  If
 needed, the validation state should be signaled by normal local
 policy mechanisms such as communities or metrics.
 On the other hand, local policy on the eBGP edge might preclude iBGP
 or eBGP announcement of signed AS Paths that are Not Valid.
 A BGPsec speaker receiving a path SHOULD perform origin validation
 per [RFC6811] and [RFC7115].
 A route server is usually 'transparent', i.e., does not insert an AS
 into the path so as not to increase the AS hop count, and thereby
 affect downstream path choices.  But, with BGPsec, a client router R
 needs to be able to validate paths that are forward signed to R.  But
 the sending router cannot generate signatures to all the possible
 clients.  Therefore, a BGPsec-aware route server needs to validate
 the incoming BGPsec_PATH and to forward updates that can be validated
 by clients that must, therefore, know the route server's AS.  This
 implies that the route server creates signatures per client including
 its own AS in the BGPsec_PATH, forward signing to each client AS, see
 [RFC8205].  The route server uses a pCount of 0 to not increase the
 effective AS hop count, thereby retaining the intent of
 'transparency'.
 If it is known that a BGPsec neighbor is a transparent route server,
 or otherwise may validly use a pCount of 0 (e.g., see [RFC8206]), the
 router SHOULD be configured to accept and process a received pCount
 of 0.  Routers MUST disallow a pCount of 0 by default.
 To prevent exposure of the internals of the BGP confederations
 [RFC5065], a BGPsec speaker exporting to a non-member removes all
 intra-confederation Secure_Path Segments.  Therefore, signing within
 the confederation will not cause external confusion even if non-
 unique private ASes are used.

Bush Best Current Practice [Page 6] RFC 8207 BGPsec Operational Considerations September 2017

8. Notes

 For protection from attacks replaying BGP data on the order of a day
 or longer old, rekeying routers with new keys (previously)
 provisioned in the RPKI is sufficient.  For one approach, see
 [ROLLOVER].
 A router that once negotiated (and/or sent) BGPsec should not be
 expected to always do so.
 Like the DNS, the Global RPKI presents only a loosely consistent
 view, depending on timing, updating, fetching, etc.  Thus, one cache
 or router may have different data about a particular prefix or router
 than another cache or router.  There is no 'fix' for this, it is the
 nature of distributed data with distributed caches.
 Operators who manage certificates SHOULD have RPKI Ghostbuster
 Records (see [RFC6493]), signed indirectly by end entity
 certificates, for those certificates on which others' routing depends
 for certificate and/or ROA validation.
 Operators should be aware of impending algorithm transitions, which
 will be rare and slow-paced, see [RFC6916].  They should work with
 their vendors to ensure support for new algorithms.
 As a router must evaluate certificates and ROAs that are time
 dependent, routers' clocks MUST be correct to a tolerance of
 approximately an hour.  The common approach is for operators to
 deploy servers that provide time service, such as [RFC5905], to
 client routers.
 If a router has reason to believe its clock is seriously incorrect,
 e.g., it has a time earlier than 2011, it SHOULD NOT attempt to
 validate incoming updates.  It SHOULD defer validation until it
 believes it is within reasonable time tolerance.

9. Security Considerations

 This document describes operational considerations for the deployment
 of BGPsec.  The security considerations for BGPsec are described in
 [RFC8205].

10. IANA Considerations

 This document does not require any IANA actions.

Bush Best Current Practice [Page 7] RFC 8207 BGPsec Operational Considerations September 2017

11. References

11.1. Normative References

 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119,
            DOI 10.17487/RFC2119, March 1997,
            <https://www.rfc-editor.org/info/rfc2119>.
 [RFC6493]  Bush, R., "The Resource Public Key Infrastructure (RPKI)
            Ghostbusters Record", RFC 6493, DOI 10.17487/RFC6493,
            February 2012, <https://www.rfc-editor.org/info/rfc6493>.
 [RFC6811]  Mohapatra, P., Scudder, J., Ward, D., Bush, R., and R.
            Austein, "BGP Prefix Origin Validation", RFC 6811,
            DOI 10.17487/RFC6811, January 2013,
            <https://www.rfc-editor.org/info/rfc6811>.
 [RFC7115]  Bush, R., "Origin Validation Operation Based on the
            Resource Public Key Infrastructure (RPKI)", BCP 185,
            RFC 7115, DOI 10.17487/RFC7115, January 2014,
            <https://www.rfc-editor.org/info/rfc7115>.
 [RFC7730]  Huston, G., Weiler, S., Michaelson, G., and S. Kent,
            "Resource Public Key Infrastructure (RPKI) Trust Anchor
            Locator", RFC 7730, DOI 10.17487/RFC7730, January 2016,
            <https://www.rfc-editor.org/info/rfc7730>.
 [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
            2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
            May 2017, <https://www.rfc-editor.org/info/rfc8174>.
 [RFC8205]  Lepinski, M., Ed. and K. Sriram, Ed., "BGPsec Protocol
            Specification", RFC 8205, DOI 10.17487/RFC8205, September
            2017, <http://www.rfc-editor.org/info/rfc8205>.

11.2. Informative References

 [KEY]      Bush, R., Turner, S., and K. Patel, "Router Keying for
            BGPsec", Work in Progress, draft-ietf-sidr-rtr-keying-13,
            April 2017.
 [RFC4271]  Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
            Border Gateway Protocol 4 (BGP-4)", RFC 4271,
            DOI 10.17487/RFC4271, January 2006,
            <https://www.rfc-editor.org/info/rfc4271>.

Bush Best Current Practice [Page 8] RFC 8207 BGPsec Operational Considerations September 2017

 [RFC5065]  Traina, P., McPherson, D., and J. Scudder, "Autonomous
            System Confederations for BGP", RFC 5065,
            DOI 10.17487/RFC5065, August 2007,
            <https://www.rfc-editor.org/info/rfc5065>.
 [RFC5905]  Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
            "Network Time Protocol Version 4: Protocol and Algorithms
            Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
            <https://www.rfc-editor.org/info/rfc5905>.
 [RFC6480]  Lepinski, M. and S. Kent, "An Infrastructure to Support
            Secure Internet Routing", RFC 6480, DOI 10.17487/RFC6480,
            February 2012, <https://www.rfc-editor.org/info/rfc6480>.
 [RFC6481]  Huston, G., Loomans, R., and G. Michaelson, "A Profile for
            Resource Certificate Repository Structure", RFC 6481,
            DOI 10.17487/RFC6481, February 2012,
            <https://www.rfc-editor.org/info/rfc6481>.
 [RFC6482]  Lepinski, M., Kent, S., and D. Kong, "A Profile for Route
            Origin Authorizations (ROAs)", RFC 6482,
            DOI 10.17487/RFC6482, February 2012,
            <https://www.rfc-editor.org/info/rfc6482>.
 [RFC6916]  Gagliano, R., Kent, S., and S. Turner, "Algorithm Agility
            Procedure for the Resource Public Key Infrastructure
            (RPKI)", BCP 182, RFC 6916, DOI 10.17487/RFC6916, April
            2013, <https://www.rfc-editor.org/info/rfc6916>.
 [RFC8206]  George, W. and S. Murphy, "BGPsec Considerations for
            Autonomous System (AS) Migration", RFC 8206,
            DOI 10.17487/RFC8206, September 2017,
            <http://www.rfc-editor.org/info/rfc8206>.
 [ROLLOVER] Weis, B., Gagliano, R., and K. Patel, "BGPsec Router
            Certificate Rollover", Work in Progess,
            draft-ietf-sidrops-bgpsec-rollover-02, August 2017.

Bush Best Current Practice [Page 9] RFC 8207 BGPsec Operational Considerations September 2017

Acknowledgements

 The author wishes to thank Thomas King, Arnold Nipper, Alvaro Retana,
 and the BGPsec design group.

Author's Address

 Randy Bush
 Internet Initiative Japan
 5147 Crystal Springs
 Bainbridge Island, Washington  98110
 United States of America
 Email: randy@psg.com

Bush Best Current Practice [Page 10]

/data/webs/external/dokuwiki/data/pages/rfc/rfc8207.txt · Last modified: 2017/09/28 03:55 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki