GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc8139

Internet Engineering Task Force (IETF) D. Eastlake 3rd Request for Comments: 8139 Y. Li Obsoletes: 6439 Huawei Updates: 6325, 7177 M. Umair Category: Standards Track IP Infusion ISSN: 2070-1721 A. Banerjee

                                                                 Cisco
                                                                 F. Hu
                                                                   ZTE
                                                             June 2017
       Transparent Interconnection of Lots of Links (TRILL):
                        Appointed Forwarders

Abstract

 TRILL (Transparent Interconnection of Lots of Links) supports multi-
 access LAN (Local Area Network) links where a single link can have
 multiple end stations and TRILL switches attached.  Where multiple
 TRILL switches are attached to a link, native traffic to and from end
 stations on that link is handled by a subset of those TRILL switches
 called "Appointed Forwarders" as originally specified in RFC 6325,
 with the intent that native traffic in each VLAN be handled by at
 most one TRILL switch.  This document clarifies and updates the
 Appointed Forwarder mechanism.  It updates RFCs 6325 and 7177 and
 obsoletes RFC 6439.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc8139.

Eastlake, et al. Standards Track [Page 1] RFC 8139 TRILL: Appointed Forwarders June 2017

Copyright Notice

 Copyright (c) 2017 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Eastlake, et al. Standards Track [Page 2] RFC 8139 TRILL: Appointed Forwarders June 2017

Table of Contents

 1. Introduction ....................................................4
    1.1. Appointed Forwarders and Active-Active .....................5
    1.2. Terminology and Abbreviations ..............................6
 2. Appointed Forwarders and Their Appointment ......................7
    2.1. The Appointment Databases and DRB Actions ..................8
    2.2. Appointment Effects of DRB Elections ......................10
         2.2.1. Processing Forwarder Appointments in Hellos ........11
         2.2.2. Frequency of Hello Appointments ....................13
         2.2.3. Appointed Forwarders Hello Limit ...................13
    2.3. Effects of Local Configuration Actions on Appointments ....14
    2.4. Overload and Appointed Forwarders .........................14
    2.5. VLAN Mapping within a Link ................................15
 3. The Inhibition Mechanism .......................................15
    3.1. Inhibited Appointed Forwarder Behavior ....................18
    3.2. Root Bridge Change Inhibition Optimizations ...............18
         3.2.1. Optimization for Change to Lower Priority ..........19
         3.2.2. Optimization for Change to Priority Only ...........19
         3.2.3. Optimizing the Detection of Completed Settling .....19
 4. Optional TRILL Hello Reduction .................................20
 5. Multiple Ports on the Same Link ................................22
 6. Port-Shutdown Messages .........................................23
    6.1. Planned Shutdown and Hellos ...............................23
    6.2. Port-Shutdown Message Structure ...........................23
    6.3. Port-Shutdown Message Transmission ........................24
    6.4. Port-Shutdown Message Reception ...........................25
    6.5. Port-Shutdown Message Security ............................25
    6.6. Port-Shutdown Configuration ...............................26
 7. FGL-VLAN Mapping Consistency Checking ..........................26
 8. Support of E-L1CS ..............................................27
    8.1. Backward Compatibility ....................................27
 9. Security Considerations ........................................28
 10. Code Points and Data Structures ...............................28
    10.1. IANA Considerations ......................................28
    10.2. AppointmentBitmap APPsub-TLV .............................29
    10.3. AppointmentList APPsub-TLV ...............................30
    10.4. FGL-VLAN-Bitmap APPsub-TLV ...............................31
    10.5. FGL-VLAN-Pairs APPsub-TLV ................................32
 11. Management Considerations .....................................33
 12. References ....................................................34
    12.1. Normative References .....................................34
    12.2. Informative References ...................................36
 Appendix A. VLAN Inhibition Example ...............................37
 Appendix B. Multi-Link VLAN Mapping Loop Example ..................38
 Appendix C. Changes to RFCs 6325, 6439, and 7177 ..................39
 Acknowledgments ...................................................40
 Authors' Addresses ................................................41

Eastlake, et al. Standards Track [Page 3] RFC 8139 TRILL: Appointed Forwarders June 2017

1. Introduction

 The IETF TRILL (Transparent Interconnection of Lots of Links)
 protocol [RFC6325] [RFC7780] provides optimal pairwise data frame
 forwarding without configuration in multi-hop networks with arbitrary
 topology and link technology, safe forwarding even during periods of
 temporary loops, and support for multipathing of both unicast and
 multicast traffic.  TRILL accomplishes these by using IS-IS
 (Intermediate System to Intermediate System) [IS-IS] [RFC7176]
 link-state routing and encapsulating traffic using a header that
 includes a hop count.  The design supports VLANs, FGLs (Fine-Grained
 Labels) [RFC7172], and optimization of the distribution of
 multi-destination frames based on VLANs and multicast groups.
 Devices that implement TRILL are called TRILL switches or "RBridges"
 (Routing Bridges).
 Section 2 of [RFC7177] discusses the environment for which the TRILL
 protocol is designed and the differences between that environment and
 the typical Layer 3 routing environment.
 TRILL supports multi-access LAN (Local Area Network) links that can
 have multiple end stations and TRILL switches attached.  Where
 multiple TRILL switches are attached to a link, native traffic to and
 from end stations on that link is handled by a subset of those
 switches called "Appointed Forwarders" as originally specified in
 [RFC6325], with the intent that native traffic in each VLAN be
 handled by at most one switch.  A TRILL switch can be Appointed
 Forwarder for many VLANs.
 The purpose of this document is to update and improve the Appointed
 Forwarder mechanism and free it from the limitations imposed by the
 requirement in its initial design that all appointments fit within a
 TRILL Hello Protocol Data Unit (PDU).  This is accomplished by
 requiring support of link-scoped FS-LSPs (Flooding Scope Link State
 PDUs) (Section 8) and providing the option to send appointment
 information in those LSPs.  In addition, this document provides a
 number of other optional features to
 1. detect inconsistent VLAN-ID-to-FGL [RFC7172] mappings among the
    TRILL switch ports on a link, as discussed in Section 7,
 2. expedite notification of ports going down so that Appointed
    Forwarders can be adjusted, as discussed in Section 6, and
 3. reduce or eliminate the need for "inhibition" of ports for loop
    safety, as discussed in Section 3.2.

Eastlake, et al. Standards Track [Page 4] RFC 8139 TRILL: Appointed Forwarders June 2017

 This document replaces and obsoletes [RFC6439], incorporating the
 former material in [RFC6439] with these additions.  The various
 optimizations are orthogonal and optional.  Implementers can choose
 to provide all, some, or none of them, and TRILL switches will still
 be interoperable.  In accordance with the TRILL design philosophy,
 these optimizations require zero or minimal configuration, but there
 are a couple of configurable parameters, as summarized in Section 11.
 As described in Appendix C, this document updates [RFC6325] by
 mandating support of E-L1CS FS-LSPs and provides backward
 compatibility in the presence of legacy TRILL switches that do not
 provide this support.  It also updates [RFC7177] by providing, as an
 optional optimization, that receipt of the Port-Shutdown message
 specified herein be treated as an event in the state machine
 specified in [RFC7177].
 This document includes reference implementation details.  Alternative
 implementations that interoperate on the wire are permitted.
 The Appointed Forwarder mechanism is irrelevant to any link on which
 end-station service is not offered.  This includes links configured
 as point-to-point IS-IS links and any link with all TRILL switch
 ports on that link configured as trunk ports.  (In TRILL,
 configuration of a port as a "trunk port" just means that no
 end-station service will be provided.  It does not imply that all
 VLANs are enabled on that port.)
 The Appointed Forwarder mechanism has no effect on the formation of
 adjacencies, the election of the Designated RBridge (DRB) [RFC7177]
 for a link, MTU matching, or pseudonode formation.  Those topics are
 covered in [RFC7177].  Furthermore, Appointed Forwarder status has
 no effect on the forwarding of TRILL Data frames; it only affects the
 handling of native frames to and from end stations.
 For other aspects of the TRILL base protocol, see [RFC6325],
 [RFC7177], and [RFC7780].  In cases of conflict between this document
 and [RFC6325] or [RFC7177], this document prevails.

1.1. Appointed Forwarders and Active-Active

 As discussed in [RFC7379], TRILL active-active provides support for
 end stations connected to multiple edge TRILL switches where these
 connections are separate links.  Since TRILL Hellos are not forwarded
 between these links, the Appointed Forwarder mechanism as described
 herein operates separately on each such link.

Eastlake, et al. Standards Track [Page 5] RFC 8139 TRILL: Appointed Forwarders June 2017

1.2. Terminology and Abbreviations

 This document uses the abbreviations and terms defined in [RFC6325],
 some of which are repeated below for convenience, and additional
 abbreviations and terms listed below.
 Data Label mapping: The mapping from VLAN ID to FGL and from FGL to
    VLAN ID.
 DRB: Designated RBridge.  The RBridge on a link elected as specified
    in [RFC7177] to handle certain decisions and tasks for that link,
    including forwarder appointment as specified herein.
 E-L1CS: Extended Level 1 Circuit Scope (Section 8).
 FGL: Fine-Grained Label [RFC7172].
 FS-LSP: Flooding Scope Link State PDU (Section 8).
 Link: The means by which adjacent TRILL switches are connected.  A
    TRILL link may be various technologies and, in the common case of
    Ethernet, can be a "bridged LAN" -- that is to say, some
    combination of Ethernet links with zero or more bridges, hubs,
    repeaters, or the like.
 LSDB: Link State Database.
 PDU: Protocol Data Unit.
 RBridge: An alternative name for a TRILL switch.
 TRILL: Transparent Interconnection of Lots of Links or Tunneled
    Routing in the Link Layer.
 TRILL switch: A device implementing the TRILL protocol.  An
    alternative name for an RBridge.
 Trunk port: A TRILL switch port configured with the "end-station
    service disable" bit on, as described in Section 4.9.1 of
    [RFC6325].
 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
 "OPTIONAL" in this document are to be interpreted as described in
 BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
 capitals, as shown here.

Eastlake, et al. Standards Track [Page 6] RFC 8139 TRILL: Appointed Forwarders June 2017

2. Appointed Forwarders and Their Appointment

 The Appointed Forwarder on a link for VLAN-x is the TRILL switch
 (RBridge) that ingresses native frames from the link and egresses
 native frames to the link in VLAN-x.  By default, the DRB (Designated
 RBridge) on a link is in charge of native traffic for all VLANs on
 the link.  The DRB may, if it wishes, act as Appointed Forwarder for
 any VLAN, and it may appoint other TRILL switches that have ports on
 the link as Appointed Forwarder for one or more VLANs.
 By definition, the DRB considers the other ports on the link to be
 the ports with which a DRB port has adjacency on that link [RFC7177].
 If the DRB loses adjacency to a TRILL switch that it has appointed
 as forwarder and the native traffic that was being handled by that
 Appointed Forwarder is still to be ingressed and egressed, it SHOULD
 immediately appoint another forwarder or itself become the forwarder
 for that traffic.
 It is important that there not be two Appointed Forwarders on a link
 that are ingressing and egressing native frames for the same VLAN at
 the same time.  Should this occur, it could form a loop where frames
 are not protected by a TRILL Hop Count for part of the loop.  (Such a
 condition can even occur through two Appointed Forwarders for two
 different VLANs, VLAN-x and VLAN-y, if ports or bridges inside the
 link are configured to map frames between VLAN-x and VLAN-y as
 discussed in Section 2.5.)  While TRILL tries to avoid such
 situations, for loop safety there is also an "inhibition" mechanism
 (see Section 3) that can cause a TRILL switch that is an Appointed
 Forwarder not to ingress or egress native frames.  Appointed
 Forwarder status and port "inhibition" have no effect on the
 reception, transmission, or forwarding of TRILL Data or TRILL IS-IS
 frames.  Appointed Forwarder status and inhibition only affect the
 handling of native frames.
 As discussed in Section 5, an RBridge may have multiple ports on a
 link.  As discussed in [RFC7177], if there are multiple ports with
 the same Media Access Control (MAC) address on the same link, all but
 one will be suspended.  The case of multiple ports on a link for the
 same TRILL switch and the case of multiple ports with the same MAC
 address on a link, as well as combinations of these cases, are fully
 accommodated; however, the case of multiple ports on a link for the
 same TRILL switch is expected to be a rare condition, and the case of
 duplicate MAC addresses is not recommended by either TRILL or
 IEEE 802.1 standards.

Eastlake, et al. Standards Track [Page 7] RFC 8139 TRILL: Appointed Forwarders June 2017

 There are six mechanisms by which an RBridge can be appointed or
 unappointed as Appointed Forwarder:
 1. assumption of appointment, when the DRB decides to act as
    Appointed Forwarder for a VLAN,
 2. E-L1CS appointment, as a result of appointments sent by the DRB in
    E-L1CS FS-LSPs,
 3. Hello appointment, as a result of appointments sent by the DRB in
    TRILL Hellos,
 4. as a result of the DRB elections [RFC7177] as discussed in
    Section 2.2,
 5. as a result of a Port-Shutdown message as discussed in Section 6,
    and
 6. as a result of a local configuration action as discussed in
    Section 2.3.
 Mechanisms 2 and 3 are covered in Section 2.1.

2.1. The Appointment Databases and DRB Actions

 The DRB MAY appoint other RBridges on the link as Appointed
 Forwarders through two mechanisms, "A" and "B", as described below.
 Each RBridge maintains two databases of appointment information:
 (1) its E-L1CS LSDB, which shows appointments that each RBridge on
 the link would make using mechanism A if that RBridge were the DRB,
 and (2) its Hello appointment database, which shows the appointments
 most recently sent by the DRB in a TRILL Hello.  The E-L1CS LSDB is
 semi-permanent and is only changed by E-L1CS FS-LSPs or IS-IS purges.
 The Hello appointment database is more transient and is completely
 reset by each Hello received from the DRB that contains any
 appointments; this database is also cleared under other
 circumstances, as described below.  An RBridge considers itself to be
 the Appointed Forwarder for VLAN-x if this is indicated by either its
 Hello appointment database or its E-L1CS LSDB entries from the DRB.

Eastlake, et al. Standards Track [Page 8] RFC 8139 TRILL: Appointed Forwarders June 2017

 The two mechanisms by which the DRB can appoint other RBridges on a
 link as Appointed Forwarders are as follows:
 (A) The inclusion of one or more Appointed Forwarders sub-TLVs
     [RFC7176], AppointmentBitmap APPsub-TLVs (Section 10.2), or
     AppointmentList APPsub-TLVs (Section 10.3) in E-L1CS LSPs it
     sends on a link.  Appointments sent using this method will not be
     seen by legacy RBridges that do not support E-L1CS (Section 8).
 (B) The inclusion of one or more Appointed Forwarders sub-TLVs
     [RFC7176] in a TRILL Hello it sends on the Designated VLAN out of
     the port that won the DRB election.  When the DRB sends any
     appointments in a TRILL Hello, it must send all appointments it
     is sending in Hellos for that link in that Hello.  Any previous
     appointment it has sent in a Hello that is not included is
     implicitly revoked.
 To avoid the size limitations of the Hello PDU, it is RECOMMENDED
 that the E-L1CS FS-LSP method be used to distribute forwarder
 appointments and that all RBridges on a link use this method to
 advertise the appointments they would make if they were the DRB.
 However, if some RBridges on a link do not support E-L1CS FS-LSPs,
 then Hello appointments must be used for the DRB to appoint such
 legacy RBridges as Appointed Forwarders.
 Although the DRB does not need to announce the VLANs for which it has
 chosen to act as Appointed Forwarder by sending appointments for
 itself, if the DRB wishes to revoke all appointments made in Hellos
 for RBridges other than itself on the link, it can do so by sending a
 TRILL Hello with just an appointment for itself for some VLAN.
 How the DRB decides what other RBridges on the link, if any, to
 appoint as forwarder for some VLAN or VLANs is beyond the scope of
 this document.
 Unnecessary changes in Appointed Forwarders SHOULD NOT be made, as
 they may result in transient lack of end-station service.
 Should the network manager have misconfigured the enabled VLANs and
 Appointed Forwarders, resulting in two RBridges believing they are
 Appointed Forwarders for the same VLAN, the scenario described in
 item 4 in Section 3 will cause one or more of the RBridges to be
 inhibited for that VLAN, thus avoiding persistent loops.

Eastlake, et al. Standards Track [Page 9] RFC 8139 TRILL: Appointed Forwarders June 2017

 When forwarder appointments are being encoded for transmission,
 different patterns of VLANs are most efficiently encoded in different
 ways.  The following table gives advice regarding the most efficient
 encoding for a given pattern:
                          sub-TLV and Reference
 Pattern of VLAN IDs          |enclosing TLV(s) and Reference
 -------------------      ------------------------------------
 Blocks of consecutive VLANs
                          Appointed Forwarders sub-TLV [RFC7176]
                              |Router CAPABILITY TLV [RFC7981]
                              |or MT-Capability TLV [RFC6329]
 Scattered VLANs within a small range
                          AppointmentBitmap APPsub-TLV (Section 10.2)
                              |TRILL GENINFO TLV [RFC7357]
 Scattered VLANs over a large range
                          AppointmentList APPsub-TLV (Section 10.3)
                              |TRILL GENINFO TLV [RFC7357]

2.2. Appointment Effects of DRB Elections

 When a TRILL switch port on a link wins the DRB election, there are
 four possible cases:
 1. A TRILL switch believes that it was the DRB and remains the DRB:
    there is no change in Appointed Forwarder status.  This also
    applies in the corner case where a TRILL switch has more than one
    port on a link, one of which was previously the DRB election
    winner but has just lost the DRB election to a different port of
    the same TRILL switch on the same link (possibly due to management
    configuration of port priorities).  In this case, there also is no
    change in which TRILL switch is the DRB.
 2. A TRILL switch believes that it was not the DRB but has now won
    the DRB election and become the DRB on a link: by default, it can
    act as Appointed Forwarder for any VLANs on that link that it
    chooses, as long as its port is not configured as a trunk port and
    has that VLAN enabled (or at least one of its ports meets these
    criteria, if it has more than one port on the link).  It ignores
    any previous forwarder appointment information it received from
    other TRILL switches on the link.

Eastlake, et al. Standards Track [Page 10] RFC 8139 TRILL: Appointed Forwarders June 2017

 3. A TRILL switch was not the DRB and does not become the DRB, but it
    observes that the port winning the DRB election has changed: the
    TRILL switch loses all Hello appointments.  In addition, there are
    two subcases:
    a. The new winning port and the old winner are ports of different
       TRILL switches on the link.  In this case, it switches to using
       the E-L1CS FS-LSP appointments for the winning TRILL switch.
    b. The new winning port and the old winner are ports of the same
       TRILL switch, which has two (or more) ports on the link:
       although the Hello appointments are still discarded, since the
       same TRILL switch is the DRB, the E-L1CS FS-LSP appointments
       are unchanged.
 4. The winning port is unchanged: as in case 1, there is no change in
    Appointed Forwarder status.

2.2.1. Processing Forwarder Appointments in Hellos

 When a non-DRB RBridge that can offer end-station service on a link
 receives a TRILL Hello that is not discarded for one of the reasons
 given in [RFC7177], it checks the source MAC address and the Port ID
 and System ID in the Hello to determine if it is from the winning DRB
 port.  If it is not from that port, any forwarder appointment
 sub-TLVs in the Hello are ignored, and there is no change in the
 receiving RBridge's Appointed Forwarder status due to that Hello.
 Also, if no forwarder appointment sub-TLVs are present in the TRILL
 Hello, there is no change in the receiver's Appointed Forwarder
 status due to that Hello.
 However, if the TRILL Hello is from the winning DRB port and the
 Hello includes one or more forwarder appointment sub-TLVs, then the
 receiving RBridge sets its Hello appointment database to be the set
 of VLANs that have both of the following characteristics:
 o  The VLAN is listed as an appointment for the receiving RBridge in
    the Hello, and
 o  The VLAN is enabled on the port where the Hello was received.
 (If the appointment includes VLAN IDs 0x000 or 0xFFF, they are
 ignored, but any other VLAN IDs are still effective.)  It then
 becomes Appointed Forwarder for all the VLANs for which it is
 appointed in either its Hello appointment database or its E-L1CS
 FS-LSP appointment database from the DRB if the VLAN is enabled and
 if the port is not configured as a trunk or IS-IS point-to-point
 port.  If the receiver was Appointed Forwarder for any VLANs because

Eastlake, et al. Standards Track [Page 11] RFC 8139 TRILL: Appointed Forwarders June 2017

 they were in the Hello appointment database and they are no longer in
 the Hello appointment database, its Appointed Forwarder status for
 such VLANs is revoked.  For example, if none of these sub-TLVs in a
 Hello appoints the receiving RBridge, then it loses all Appointed
 Forwarder status on the port where the Hello was received due to
 Hello appointment database entries, but it retains Appointed
 Forwarder status due to E-L1CS FS-LSP appointments.
 The handling of one or more forwarder appointment sub-TLVs in a Hello
 from the winning port that appoints the receiving RBridge is as
 follows: an appointment in an Appointed Forwarders sub-TLV is for a
 specific RBridge and a contiguous interval of VLAN IDs; however, as
 stated above, it actually appoints that RBridge as forwarder only for
 the VLAN or VLANs in that range that are enabled on one or more ports
 that RBridge has on the link (ignoring any ports configured as
 trunk ports or as IS-IS point-to-point ports).
 There is no reason for an RBridge to remember that it received a
 valid appointment Hello message for a VLAN that was ineffective
 because the VLAN was not enabled on the port where the Hello was
 received or because the port was a trunk or point-to-point port.  It
 does not become Appointed Forwarder for such a VLAN just because that
 VLAN is later enabled or the port is later reconfigured.
 The limitations due to the size of the Hello PDU make it desirable to
 use E-L1CS FS-LSPs for appointment.  But if Hellos need to be used,
 due to TRILL switches on the link not supporting E-L1CS FS-LSPs, the
 remainder of this section provides a method to maximize the use of
 the limited space in Hellos for forwarder appointment.
 It should be straightforward for the DRB to send, within one Hello,
 the appointments for several dozen VLAN IDs or several dozen blocks
 of contiguous VLAN IDs.  Should the VLANs that the DRB wishes to
 appoint be inconveniently distributed (for example, the proverbial
 case where a DRB (say RB1) wishes to appoint RB2 as forwarder for all
 even-numbered VLANs and appoint RB3 as forwarder for all odd-numbered
 VLANs), the following method may be used:
    The network manager normally controls what VLANs are enabled on an
    RBridge port.  Thus, the network manager can appoint an RBridge as
    forwarder for an arbitrary set of scattered VLANs by enabling only
    those VLANs on the relevant port (or ports) and then having the
    DRB send an appointment that appears to appoint the target RBridge
    as forwarder for all VLANs.  However, for proper operation and
    inter-RBridge communication, the Designated VLAN for a link SHOULD
    be enabled on all RBridge ports on that link, and it may not be
    desired to appoint the RBridge as forwarder for the
    Designated VLAN.  Thus, in the general case, two appointments

Eastlake, et al. Standards Track [Page 12] RFC 8139 TRILL: Appointed Forwarders June 2017

    would be required, although only one appointment would be required
    if the Designated VLAN value were extremely low or high (such as
    VLAN 0xFFE) or the default value (VLAN 1).
 For example, assume that the DRB wants RB2 to be Appointed Forwarder
 for all even-numbered VLANs and the Designated VLAN for the link is
 VLAN 101.  The network manager could cause all even-numbered VLANs
 plus VLAN 101 to be enabled on the relevant port of RB2 and then,
 with the desired effect, cause the DRB to send appointments to RB2
 appointing it forwarder for all VLANs from 1 through 100 and from 102
 through 4,094.

2.2.2. Frequency of Hello Appointments

 Appointments made through E-L1CS FS-LSPs use the same IS-IS timing
 constants as those for LSP flooding.  The general IS-IS link-state
 flooding mechanism is robust and includes acknowledgments so that it
 automatically recovers from lost PDUs, rebooted TRILL switches, and
 the like.
 For Hello appointments, it is not necessary for the DRB to include
 the Hello forwarder appointments in every TRILL Hello that it sends
 on the Designated VLAN for a link.  For loop safety, every RBridge is
 required to indicate, in every TRILL Hello it sends in VLAN-x on a
 link, whether it is an Appointed Forwarder for VLAN-x for that link
 (see item 4 in Section 3, but see also Section 4).  It is also
 RECOMMENDED that the DRB have enabled all VLANs for which end-station
 service will be offered on the link as well as the Designated VLAN.
 Thus, the DRB will generally be informed by other RBridges on the
 link of the VLANs for which they believe that they are the Appointed
 Forwarder.  If this matches the appointments the DRB wishes to make,
 it is not required to resend its forwarder appointments; however, for
 robustness, especially in cases such as VLAN misconfigurations in a
 bridged LAN link, it is RECOMMENDED that the DRB send its forwarder
 appointments on the Designated VLAN at least once per its Holding
 Time on the port that won the DRB election.

2.2.3. Appointed Forwarders Hello Limit

 The Hello mechanism of DRB forwarder appointment and the limited
 length of TRILL Hellos impose a limit on the number of RBridges on a
 link that can be Appointed Forwarders when E-L1CS FS-LSP appointments
 cannot be used due to the presence of legacy RBridges.  To obtain a
 conservative estimate of this limit, assume that no more than
 1,000 bytes are available in a TRILL Hello for such appointments.
 Assume also that it is desired to appoint various RBridges on a link
 as forwarder for arbitrary non-intersecting sets of VLANs.  Using the
 technique discussed at the end of Section 2.2.1 would generally

Eastlake, et al. Standards Track [Page 13] RFC 8139 TRILL: Appointed Forwarders June 2017

 require two appointments, or 12 bytes, per RBridge.  With allowance
 for sub-TLV and TLV overhead, appointments for 83 RBridges would
 fit in under 1,000 bytes.  Including the DRB, this implies a link
 with 84 or more RBridges attached.  Links with more than a handful of
 RBridges attached are expected to be rare, and in any case such
 limitations are easily avoided by using E-L1CS FS-LSP appointment.

2.3. Effects of Local Configuration Actions on Appointments

 Disabling VLAN-x at an RBridge port cancels any Appointed Forwarder
 status that RBridge has for VLAN-x, unless VLAN-x is enabled on some
 other port that the RBridge has connected to the same link.
 Configuring a port as a trunk port or point-to-point port revokes
 any Appointed Forwarder status that depends on enabled VLANs at
 that port.
 Causing a port to no longer be configured as a trunk or
 point-to-point port or enabling VLAN-x on a port does not necessarily
 cause the RBridge to become an Appointed Forwarder for the link that
 port is on.  However, such actions allow the port's RBridge to become
 Appointed Forwarder by choice if it is the DRB or, if it is not the
 DRB on the link, by appointment as indicated by the Hello appointment
 database or the E-L1CS FS-LSP appointment database.

2.4. Overload and Appointed Forwarders

 A TRILL switch in link-state overload [RFC7780] will, in general, do
 a poorer job of forwarding frames than a TRILL switch not in
 overload, because the TRILL switch not in overload has full knowledge
 of the campus topology.  For example, as explained in [RFC7780], an
 overloaded TRILL switch may not be able to distribute
 multi-destination TRILL Data packets at all.
 Therefore, the DRB SHOULD NOT appoint an RBridge in overload as an
 Appointed Forwarder, and if an Appointed Forwarder becomes
 overloaded, the DRB SHOULD reassign VLANs from the overloaded RBridge
 to another RBridge on the link that is not overloaded, if one is
 available.
 A counter-example where it would be best to appoint an RBridge in
 overload as Appointed Forwarder would be if RB1 was in overload but
 all end stations in the campus in VLAN-x were on links attached to
 RB1.  In such a case, RB1 would never have to route VLAN-x
 end-station traffic as TRILL Data packets but would always be
 forwarding them locally as native frames.  In this case, RB1
 SHOULD NOT be disadvantaged for selection as the VLAN-x Appointed
 Forwarder on any such links, even if RB1 is in overload.

Eastlake, et al. Standards Track [Page 14] RFC 8139 TRILL: Appointed Forwarders June 2017

 There is also the case where it is unavoidable to appoint an RBridge
 in overload as Appointed Forwarder, because all RBridges on the link
 are in overload.
 These cases do not violate the prohibition in the IS-IS standard
 against routing through an overloaded node.  Designation as an
 Appointed Forwarder has to do with the ingress and egress of native
 frames and has nothing to do with the IS-IS routing of TRILL Data
 packets through a TRILL switch.
 Overload does not affect DRB election, but a TRILL switch in overload
 MAY reduce its own priority to be the DRB.

2.5. VLAN Mapping within a Link

 TRILL Hellos include a field that is set to the VLAN in which they
 are sent when they are sent on a link technology such as Ethernet
 that has outer VLAN labeling.  (For link technologies such as PPP
 that do not have outer VLAN labeling, this Hello field is ignored.)
 If a TRILL Hello arrives on a different VLAN than the VLAN on which
 it was sent, then VLAN mapping is occurring within the link.  VLAN
 mapping between VLAN-x and VLAN-y can lead to a loop if the Appointed
 Forwarders for the VLANs are different.  If such mapping within a
 link was allowed and occurred on two or more links so that there was
 a cycle of VLAN mappings, a multi-destination frame would loop
 forever.  Such a frame would be "immortal".  For a specific example,
 see Appendix B.
 To prevent this potential problem, if the DRB on a link detects VLAN
 mapping by receiving a Hello in VLAN-x that was sent on VLAN-y, it
 MUST make or revoke appointments so as to assure that the same TRILL
 switch (possibly the DRB) is the Appointed Forwarder on the link for
 both VLAN-x and VLAN-y.

3. The Inhibition Mechanism

 A TRILL switch has, for every link on which it can offer end-station
 service (that is, every link for which it can act as an Appointed
 Forwarder), the following timers, denominated in seconds:
  1. a DRB inhibition timer,
  1. a root bridge change inhibition timer, and
  1. up to 4,094 VLAN inhibition timers, one for each legal VLAN ID.
 The DRB and root bridge change inhibition timers MUST be implemented.

Eastlake, et al. Standards Track [Page 15] RFC 8139 TRILL: Appointed Forwarders June 2017

 The loss of native traffic due to inhibition will be minimized by
 logically implementing a VLAN inhibition timer per each VLAN for
 which end-station service will ever be offered by the RBridge on the
 link; this SHOULD be done.  (See Appendix A for an example
 illustrating a potential problem that is solved by VLAN inhibition
 timers.)  However, if implementation limitations make a full set of
 such timers impractical, the VLAN inhibition timers for more than one
 VLAN can, with care, be merged into one timer.  In particular, an
 RBridge MUST NOT merge the VLAN inhibition timers for two VLANs if it
 is the Appointed Forwarder for one but not for the other, as this can
 lead to unnecessary indefinitely prolonged inhibition.  In a given
 implementation limitation, there will be safe operations, albeit with
 more loss of native frames than would otherwise be required, even if
 only two VLAN inhibition timers are provided: one for the VLANs for
 which the RBridge is the Appointed Forwarder and one for all other
 VLANs.  Thus, at least two VLAN inhibition timers MUST be
 implemented.  Where a VLAN inhibition timer represents more than one
 VLAN, an update or test that would have been done to the timer for
 any of the VLANs is performed on the merged timer.
 These timers are set as follows:
 1. On booting or management reset, each port will have its own set of
    timers, even if two or more such ports are on the same link,
    because the TRILL switch will not have had a chance yet to learn
    that they are on the same link.  All inhibition timers are set to
    "expired", except the DRB inhibition timer that is set in
    accordance with item 2 below.  The DRB inhibition timer is handled
    differently, because each port will initially believe that it is
    the DRB.
 2. When a TRILL switch decides that it has become the DRB on a link,
    including when it is first booted or reset by management, it sets
    the DRB inhibition timer to the Holding Time of its port on that
    link that won the DRB election.
 3. When a TRILL switch decides that it has lost DRB status on a link,
    it sets the DRB inhibition timer to "expired".
 Note: In the corner case where one port of a TRILL switch was the DRB
 election winner but later lost the DRB election to a different port
 of the same TRILL switch on that link (perhaps due to management
 configuration of port priorities), neither item 2 nor item 3 above
 applies, and the DRB timer is not changed.
 4. When a TRILL switch RB1 receives a TRILL Hello asserting that the
    sender is the Appointed Forwarder and that Hello either
    (1) arrives on VLAN-x or (2) was sent on VLAN-x as indicated

Eastlake, et al. Standards Track [Page 16] RFC 8139 TRILL: Appointed Forwarders June 2017

    inside the Hello, RB1 uses as its VLAN-x inhibition timer for the
    link (1) that timer's existing value or (2) the Holding Time in
    the received Hello, whichever is longer.  A TRILL switch MUST
    maintain VLAN inhibition timers covering a link to which it
    connects if it can offer end-station service on that link, even if
    it is not currently the Appointed Forwarder for any VLAN on that
    link.
 5. When a TRILL switch RB1 enables VLAN-x on a port connecting to a
    link and VLAN-x was previously not enabled on any of RB1's ports
    on that link, it sets its VLAN inhibition timer for VLAN-x for
    that link to its Holding Time for that port.  This is done even if
    the port is configured as a trunk or point-to-point port, as long
    as there is some chance it might later be configured not to be a
    trunk or point-to-point port.  Remember, inhibition has no effect
    on TRILL Data or IS-IS packets; inhibition only affects native
    frames.
 6. When a TRILL switch detects a change in the common spanning tree
    root bridge on a port, it sets its root bridge change inhibition
    timer for the link to an amount of time that defaults to
    30 seconds and is configurable to any value from 30 down to
    0 seconds.  This condition will not occur unless the TRILL switch
    is receiving Bridge PDUs (BPDUs) on the port from an attached
    bridged LAN; if no BPDUs are being received, the root bridge
    change inhibition timer will never be set.  It is safe to
    configure this inhibition time to the settling time of an attached
    bridged LAN.  For example, if it is known that the Rapid Spanning
    Tree Protocol (RSTP) [802.1Q] is running throughout the attached
    bridged LAN, it is safe to configure this inhibition time to
    7 seconds or, if the attached bridges have been configured to have
    a minimum Bridge Hello Timer, it is safe to configure it to
    4 seconds.  Further optimizations are specified in Section 3.2.
 7. When a TRILL switch decides that one of its ports (or a set of its
    ports) P1 is on the same link as another one of its ports (or set
    of its ports) P2, the inhibition timers are merged into a single
    set of inhibition timers by using the longest value of the
    corresponding timers as the initial value of the merged timers.
 8. When an RBridge decides that a set of its ports that it had been
    treating as being on the same link are no longer on the same link,
    those ports will necessarily be on two or more links (up to one
    link per port).  This is handled by cloning a copy of the timers
    for each of the two or more links to which the TRILL switch has
    decided these ports connect.

Eastlake, et al. Standards Track [Page 17] RFC 8139 TRILL: Appointed Forwarders June 2017

3.1. Inhibited Appointed Forwarder Behavior

 Inhibition has no effect on the receipt or forwarding of TRILL Data
 packets or TRILL IS-IS packets.  It only affects ingressing and
 egressing native frames.
 An Appointed Forwarder for a link is inhibited for VLAN-x if:
 1. its DRB inhibition timer for that link is not expired,
 2. its root bridge change inhibition timer for that link is not
    expired, or
 3. its VLAN inhibition timer for that link covering VLAN-x is not
    expired.
 If a VLAN-x Appointed Forwarder for a link is inhibited and receives
 a TRILL Data packet whose encapsulated frame would normally be
 egressed to that link in VLAN-x, it decapsulates the native frame as
 usual.  However, it does not output it to, or queue it for, that
 link, although, if appropriate (for example, the frame is
 multi-destination), it may output it to, or queue it for, other
 links.
 If a VLAN-x Appointed Forwarder for a link is inhibited and receives
 a native frame in VLAN-x that would normally be ingressed from that
 link, the native frame is ignored, except for address learning.
 A TRILL switch with one or more unexpired inhibition timers, possibly
 including an unexpired inhibition timer covering VLAN-x, is still
 required to indicate in TRILL Hellos it sends on VLAN-x whether or
 not it is Appointed Forwarder for VLAN-x for the port on which it
 sends the Hello.

3.2. Root Bridge Change Inhibition Optimizations

 The subsections below specify three optimizations that can reduce the
 inhibition time of an RBridge port under certain circumstances for
 changes in the root Bridge ID [802.1Q] being received by that port
 and thus decrease any transient interruption in end-station service
 due to inhibition.  TRILL switches MAY implement these optimizations.
 In the first two optimizations, inhibition can be eliminated entirely
 under some circumstances.  These optimizations are a bit heuristic in
 that with some unlikely multiple changes in a bridged LAN that occur
 simultaneously, or nearly so, the optimizations make transient
 looping more likely.

Eastlake, et al. Standards Track [Page 18] RFC 8139 TRILL: Appointed Forwarders June 2017

3.2.1. Optimization for Change to Lower Priority

 Assume that the root Bridge ID being received on an RBridge port
 changes to a new root Bridge ID with lower priority and a different
 root Bridge MAC address due to a single change in the bridged LAN.
 There are two possible reasons for this:
 1. The bridged LAN to which the port is connected has partitioned
    into two or more parts due to link failure or otherwise, and the
    port is connected to a part that does not contain the original
    root bridge.
 2. The original root bridge has been reconfigured to have a lower
    priority, and a new root has taken over.
 Both of these scenarios are safe conditions that do not require
 inhibition.

3.2.2. Optimization for Change to Priority Only

 Assume that the root Bridge ID changes due to a single change in the
 bridged LAN but only the explicit priority portion of it changes.
 This means that the 48-bit MAC address portion of the root Bridge ID
 is unchanged and the root bridge has been reconfigured to have a
 different priority.  Thus, the same bridge is root, and a topology
 change is not indicated.  Thus, it is safe to ignore this sort of
 root Bridge ID change and not invoke the inhibition mechanism.

3.2.3. Optimizing the Detection of Completed Settling

 A dangerous case is the merger of bridged LANs that had been separate
 TRILL links in the same campus.  In general, these links may have had
 different Appointed Forwarders on them for the same VLAN.  Without
 inhibition, loops involving those VLANs could occur after the merger.
 Only native frames egressed and ingressed by RBridges are a potential
 problem.  TRILL Data packets are either
 1. individually addressed (TRILL Header M bit = 0) and will be
    ignored if delivered to any incorrect TRILL switch ports or
 2. multicast (TRILL Header M bit = 1), in which case the Reverse Path
    Forwarding Check discards any copies delivered to incorrect TRILL
    switch ports.
 Thus, there is no need for inhibition to affect the sending or
 receiving of TRILL Data packets, and inhibition does not do so.

Eastlake, et al. Standards Track [Page 19] RFC 8139 TRILL: Appointed Forwarders June 2017

 However, root bridge change inhibition is only needed until TRILL
 Hellos have been exchanged on the merged bridged LAN.  Hellos
 indicate Appointed Forwarder status and, in general, after an
 exchange of Hellos the new merged bridged LAN link will, if
 necessary, be rendered TRILL loop safe by VLAN inhibition so that
 root bridge change inhibition is no longer needed.
 TRILL switches are required to advertise in their link state the IDs
 of the root Bridge IDs they can see.  If an RBridge port sees a
 change in root Bridge ID from Root1 to Root2, it is safe to terminate
 root bridge change inhibition on that port as soon as Hellos have
 been received on the port from all RBridges that can see Root1 or
 Root2, except any such RBridge that is no longer reachable.
 In further detail, when a change from Root1 to Root2 is noticed at a
 port of RB1, RB1 associates with that port a list of all of the
 reachable RBridges, other than itself, that had reported in their
 LSPs that they could see either Root1 or Root2.  It then removes from
 this list any RBridge that becomes unreachable from RB1 or from which
 it has received a Hello on that port.  If there is a subsequent
 change in root Bridge ID being received before this list is empty,
 say to Root7, then those RBridges reporting in their LSPs that they
 can see Root7 are added to the list.  Root bridge change inhibition
 can be terminated for the port as soon as either the timeout is
 reached or this list of RBridges is empty.
 If the optimizations described in Sections 3.2.1 and/or 3.2.2 are in
 effect at an RBridge port and indicate that no inhibition is needed,
 then the mechanism described in this section is not needed either.

4. Optional TRILL Hello Reduction

 If a network manager has sufficient confidence that they know the
 configuration of bridges, ports, and the like, within an Ethernet
 link, they may be able to reduce the number of TRILL Hellos sent on
 that link by sending Hellos in fewer VLANs -- for example, if all
 TRILL switches on the link will see all Hellos without VLAN
 constraints.  However, because adjacencies are established in the
 Designated VLAN, an RBridge MUST always attempt to send Hellos in the
 Designated VLAN.
 Hello reduction makes TRILL less robust in the face of decreased VLAN
 connectivity within a link, such as partitioned VLANs, VLANs disabled
 on ports, or disagreement over the Designated VLAN; however, as long
 as all RBridge ports on the link are configured for the same
 Desired Designated VLAN [RFC6325], can see each other's frames in
 that VLAN, and utilize the mechanisms specified below to update VLAN
 inhibition timers, operations will be safe.  (These considerations

Eastlake, et al. Standards Track [Page 20] RFC 8139 TRILL: Appointed Forwarders June 2017

 do not arise on links between RBridges that are configured as
 point to point, since, in that case, each RBridge sends
 point-to-point Hellos, other TRILL IS-IS PDUs, and TRILL Data frames
 only in what it believes to be the Designated VLAN of the link
 (although it may send them untagged) and no native frame end-station
 service is provided.  Thus, for such links, there is no reason to
 send Hellos in any VLAN other than the Designated VLAN.)
 The provision for a configurable set of "Announcing VLANs", as
 described in Section 4.4.3 of [RFC6325], provides a mechanism in the
 TRILL base protocol for a reduction in TRILL Hellos.
 To maintain loop safety in the face of occasional lost frames,
 RBridge failures, link failures, new RBridges coming up on a link,
 and the like, the inhibition mechanism specified in Section 3 is
 still required.  Strictly following Section 3, a VLAN inhibition
 timer can only be set by the receipt of a Hello sent or received in
 that VLAN.  Thus, to safely send a reduced number of TRILL Hellos on
 a reduced number of VLANs requires additional mechanisms to set the
 VLAN inhibition timers at an RBridge.  Two such mechanisms, specified
 below, expand upon the mechanisms provided in Section 3.  Support for
 both of these mechanisms is indicated by a capability bit in the
 PORT-TRILL-VER sub-TLV (Section 5.4 of [RFC7176]).  It may be unsafe
 for an RBridge to send TRILL Hellos on fewer VLANs than the set of
 VLANs recommended in [RFC6325] on a link unless all its adjacencies
 on that link (excluding those in the Down state [RFC7177]) indicate
 support of these mechanisms and these mechanisms are in use.
 1. An RBridge RB2 MAY include in any TRILL Hello an Appointed
    Forwarders sub-TLV [RFC7176] appointing itself for one or more
    ranges of VLANs.  The Appointee Nickname field(s) in the
    self-appointment Appointed Forwarders sub-TLV MUST be the same as
    the Sender Nickname in the Special VLANs and Flags sub-TLV in the
    TRILL Hellos sent by RB2.  This indicates that the sending RBridge
    believes that it is Appointed Forwarder for those VLANs.  For each
    of an RBridge's VLAN inhibition timers for every VLAN in the block
    or blocks listed in the Appointed Forwarders sub-TLV, the RBridge
    sets that timer to either (1) its current value or (2) the Holding
    Time of the Hello containing the sub-TLV, whichever is longer.
    This is backward compatible.  That is, such sub-TLVs will have no
    effect on any legacy receiving RBridge not implementing this
    mechanism unless RB2, the sending RBridge, is the DRB sending
    Hellos on the Designated VLAN.  If RB2 is the DRB, it MUST include
    in the Hello all forwarder appointments, if any, for RBridges
    other than itself on the link.

Eastlake, et al. Standards Track [Page 21] RFC 8139 TRILL: Appointed Forwarders June 2017

 2. An RBridge MAY use the VLANs Appointed sub-TLV [RFC7176].  When
    RB1 receives a VLANs Appointed sub-TLV in a TRILL Hello from RB2
    on any VLAN, RB1 updates the VLAN inhibition timers for all the
    VLANs that RB2 lists in that sub-TLV as VLANs for which RB2 is
    Appointed Forwarder.  Each such timer is updated to (1) its
    current value or (2) the Holding Time of the TRILL Hello
    containing the VLANs Appointed sub-TLV, whichever is longer.  This
    sub-TLV will be an unknown sub-TLV to RBridges not implementing
    it, and such RBridges will ignore it.  Even if a TRILL Hello sent
    by the DRB on the Designated VLAN includes one or more VLANs
    Appointed sub-TLVs, as long as no Appointed Forwarders sub-TLVs
    appear, the Hello is not required to indicate all forwarder
    appointments.
 Two different encodings are provided above to optimize the listing of
 VLANs.  Large blocks of contiguous VLANs are more efficiently encoded
 with the Appointed Forwarders sub-TLV, and scattered VLANs are more
 efficiently encoded with the VLANs Appointed sub-TLV.  These
 encodings may be mixed in the same Hello.  The use of these sub-TLVs
 does not affect the requirement that the AF bit in the Special VLANs
 and Flags sub-TLV MUST be set if the originating RBridge believes
 that it is Appointed Forwarder for the VLAN in which the Hello
 is sent.
 If the above mechanisms are used on a link, then each RBridge on the
 link MUST send Hellos in one or more VLANs with such VLANs Appointed
 sub-TLV(s) and/or self-appointment Appointed Forwarders sub-TLV(s),
 and the AF bit is appropriately set such that no VLAN inhibition
 timer will improperly expire unless three or more Hellos are lost.
 For example, an RBridge could announce all VLANs for which it
 believes that it is Appointed Forwarder in a Hello sent on the
 Designated VLAN three times per Holding Time.

5. Multiple Ports on the Same Link

 A TRILL switch may have multiple ports on the same link.  Some of
 these ports may be suspended due to MAC address duplication, as
 described in [RFC7177].  Suspended ports never ingress or egress
 native frames.
 If a TRILL switch has one or more non-suspended ports on a link and
 those ports offer end-station service -- that is, those ports are not
 configured as point-to-point or trunk ports -- then that TRILL switch
 is eligible to be an Appointed Forwarder for that link.  It can
 become Appointed Forwarder in the ways discussed in Section 2.

Eastlake, et al. Standards Track [Page 22] RFC 8139 TRILL: Appointed Forwarders June 2017

 If a TRILL switch that is the Appointed Forwarder for VLAN-x on a
 link has multiple non-suspended ports on that link, it may load-share
 the task of ingressing and egressing VLAN-x native frames across
 those ports however it chooses, as long as there is no case in which
 a frame it egresses onto the link from one port can be ingressed on
 another one of its ports, creating a loop.  If the TRILL switch is
 the Appointed Forwarder for multiple VLANs, a straightforward thing
 to do would be to partition those VLANs among the ports it has on
 the link.

6. Port-Shutdown Messages

 A TRILL switch may note that one of its ports has failed, or it
 may be about to shut down that port.  If the port is on a link along
 with ports of other TRILL switches, those TRILL switches will not
 notice the port shutdown or failure using TRILL base protocol
 mechanisms until there is a failure to receive a number of Hellos
 from that port.  This can take many seconds.  Network topology
 (adjacencies) and forwarder appointments can react more rapidly to
 port shutdown or failure through explicit notification.  As discussed
 below, this notification SHOULD be provided through the Port-Shutdown
 message.

6.1. Planned Shutdown and Hellos

 A TRILL switch that is shutting down one of its ports (say P1) soon
 SHOULD reduce its Holding Time on that port, so that the shutdown
 will be more rapidly noticed by adjacent RBridges that might not
 support the Port-Shutdown message.

6.2. Port-Shutdown Message Structure

 The Port-Shutdown message is an RBridge Channel message [RFC7178]
 using RBridge Channel Protocol number 0x006.  The payload specific to
 the Channel Protocol consists of a list of Port IDs (see
 Section 4.4.2 of [RFC6325]) for the port or ports that have failed or
 are being shut down, as shown in the diagram below.  Support for the
 Port-Shutdown message is advertised by simply advertising support for
 its RBridge Channel Protocol in the RBridge Channel Protocols sub-TLV
 [RFC7176].

Eastlake, et al. Standards Track [Page 23] RFC 8139 TRILL: Appointed Forwarders June 2017

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 TRILL Header:                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                   | V |A|C|M| RESV  |F| Hop Count |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Egress Nickname         |       Ingress Nickname        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |         Special Inner.MacDA = All-Egress-RBridges             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Special Inner.MacDA (cont.)  |         Inner.MacSA           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Inner.MacSA (cont.)                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    VLAN Tag Ethertype=0x8100  | Priority=7, DEI=0, VLAN ID=1  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 RBridge Channel Header:
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | RBridge-Chan. Ethertype=0x8946| CHV=0 | Channel Protocol=0x006|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |          Flags        | ERR=0 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Information specific to the Port-Shutdown Channel Protocol:
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Port ID 1                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Port ID 2                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Port ID K                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

6.3. Port-Shutdown Message Transmission

 For robustness, a TRILL switch sends a configurable number of copies
 of Port-Shutdown messages separated by a configurable time interval.
 The default number of copies is two, although this can be configured
 as one copy or as three copies, and the default interval is
 20 milliseconds (see Section 6.6).  As with any "adjacency critical"
 message, the Port-Shutdown message SHOULD be sent with the highest
 priority, which is priority 7, and SHOULD NOT be marked as
 "drop eligible".
 If a failure of port P1 on RBridge RB2 is detected by RB2, then the
 Port-Shutdown message announcing this failure is sequentially unicast
 through the rest of the TRILL campus to all RBridges (1) with which
 P1 had an adjacency and (2) that are advertising support for the
 Port-Shutdown RBridge Channel Protocol.

Eastlake, et al. Standards Track [Page 24] RFC 8139 TRILL: Appointed Forwarders June 2017

 If a port shutdown is planned within 1 second, then the TRILL switch
 ceases to send Hellos out of the port being shut down and either
 (1) sends the Port-Shutdown message to RBridge ports on the link
 advertising support of the Port-Shutdown RBridge Channel Protocol or
 (2) broadcasts the Port-Shutdown message announcing this event
 through the port as follows:
  1. The Outer.MacDA is the All-RBridges multicast address.
  1. If an outer VLAN tag is present, it specifies the Designated VLAN

for the link, SHOULD specify priority 7, and SHOULD NOT specify

    "drop eligible".
  1. In the TRILL Header, the egress nickname is All-RBridges, and the

M bit in the TRILL Header is set to 0.

  1. In the RBridge Channel Header, the MH and NA bits are zero.
 There is no need for a special message to indicate that a port P1 has
 come back up or that a shutdown has been "canceled".  This is
 indicated by simply sending Hellos out of port P1.

6.4. Port-Shutdown Message Reception

 When a TRILL switch RB1 receives a Port-Shutdown message, RB1 checks
 to see if the ingress nickname specifies some TRILL switch RB2 with
 which RB1 has one or more adjacencies.  If so, it drops those
 adjacencies that are to RB2 ports whose Port IDs are listed in the
 Port-Shutdown message.  There could be more than one if RB2 had
 multiple ports on the link that are going down.
 If RB1 is the DRB and this eliminates all adjacencies on a link
 between the DRB and RB2, then, for all VLANs whose ingress/egress was
 being handled by RB2, the DRB either starts acting as Appointed
 Forwarder or appoints some new TRILL switch with which it has
 adjacency as Appointed Forwarder.

6.5. Port-Shutdown Message Security

 Port-Shutdown messages can be secured through the use of the RBridge
 Channel Header Extension security feature [RFC7978].

Eastlake, et al. Standards Track [Page 25] RFC 8139 TRILL: Appointed Forwarders June 2017

6.6. Port-Shutdown Configuration

 There are two Port-Shutdown configuration parameters, as listed
 below.  Section 6.3 provides details regarding their use.
    Parameter            Default                 Range
    ---------------   ----------------   ---------------------
    PShutdownRepeat     2                 1-3
    PShutdownDelay     20 milliseconds    0-1,000 milliseconds

7. FGL-VLAN Mapping Consistency Checking

 TRILL switches support 24-bit Fine-Grained Labels as specified in
 [RFC7172].  Basically, a VLAN ID in native traffic between an edge
 TRILL switch and an end station is mapped from/to an FGL as an
 Inner.Label in TRILL Data packets.  Since the Appointed Forwarder for
 a VLAN will be ingressing and egressing such native traffic, the
 mapping configured at the Appointed Forwarder is the mapping
 performed.
 However, the Appointed Forwarder for VLAN-x on a link can change for
 reasons discussed elsewhere in this document.  Thus, all
 TRILL switches on a link that are configured with an FGL-VLAN mapping
 SHOULD be configured with the same mapping.  Otherwise, traffic might
 unpredictably jump from one FGL to another when the Appointed
 Forwarder changes.  TRILL switches SHOULD advertise their mapping on
 the link using the FGL-VLAN-Bitmap and FGL-VLAN-Pairs APPsub-TLVs
 (Sections 10.4 and 10.5) so that consistency checking can be
 automated.
 A TRILL switch SHOULD compare the FGL-VLAN mappings that it sees
 advertised by other TRILL switches on a link with its own and alert
 the network operator if they are inconsistent.  "Inconsistent" means
 that (1) one TRILL switch maps FGL-z to VLAN-x while another maps
 FGL-z to VLAN-y or (2) one TRILL switch maps VLAN-x to FGL-w while
 another maps VLAN-x to FGL-z, all on the same link.
 Depending on how the network is being managed, a transient
 inconsistency may not be a problem.  Thus, the network operator
 SHOULD NOT be alerted unless the inconsistency persists for a period
 of time that defaults to the TRILL switch's Holding Time and is
 configurable to between 0 seconds and 2**16 - 1 seconds,
 where 2**16 - 1 is a special value and indicates that such alerts
 are disabled.

Eastlake, et al. Standards Track [Page 26] RFC 8139 TRILL: Appointed Forwarders June 2017

8. Support of E-L1CS

 All TRILL switches MUST support the E-L1CS flooding scope [RFC7356],
 Extended Level 1 Flooding Scope (E-L1FS) [RFC7780], and base LSPs
 [IS-IS].  It will be apparent to any TRILL switch on a link if any
 other TRILL switch on the link is a legacy implementation not
 supporting E-L1CS because, as stated in [RFC7780], all TRILL switches
 MUST include a Scope Flooding Support TLV [RFC7356] in all TRILL
 Hellos they send.  This support of E-L1CS increases the amount of
 information from each TRILL switch that can be synchronized on the
 link, compared with the information capacity of Hellos, by several
 orders of magnitude.
 For robustness, E-L1CS PDUs (FS-LSP fragments, E-L1CS FS-CSNPs
 (Flooding Scope Complete Sequence Number PDUs) [RFC7356], and E-L1CS
 FS-PSNPs (Flooding Scope Partial Sequence Number PDUs) [RFC7356])
 MUST NOT exceed 1,470 bytes in length; however, any such E-L1CS PDU
 that is received that is longer than 1,470 bytes is processed
 normally.
 As with any type of IS-IS LSP, FS-LSPs are identified by the
 System ID of the originating router (TRILL switch) and the
 fragment number.  In particular, there is no port identifier in the
 header of an E-L1CS PDU.  Thus, a TRILL switch RB1 with more than one
 non-suspended port on a link (Section 5) transmitting such a PDU MAY
 transmit it out of any one or more of such ports.  RB1 will generally
 receive such a PDU that other TRILL switches send on all of RB1's
 ports on the link.  In addition, with multiple ports on the link, it
 will receive any such PDU that it sends on the ports it has on the
 link other than the transmitting port.

8.1. Backward Compatibility

 Future TRILL specifications making use of E-L1CS MUST specify how
 situations involving a TRILL link will be handled when one or more
 TRILL switches attached to that link support E-L1CS and one or more
 do not.

Eastlake, et al. Standards Track [Page 27] RFC 8139 TRILL: Appointed Forwarders June 2017

9. Security Considerations

 This document provides improved documentation of the TRILL Appointed
 Forwarder mechanism.  It does not change the security considerations
 of the TRILL base protocol as described in Section 6 of [RFC6325].
 The Port-Shutdown messages specified in Section 6 are sent using the
 RBridge Channel facility [RFC7178].  Such messages SHOULD be secured
 through the use of the RBridge Channel Header Extension [RFC7978].
 If they are not adequately secured, they are a potential
 denial-of-service vector.
 The E-L1CS FS-LSPs added by Section 8 are a type of IS-IS PDU
 [RFC7356].  As such, they are securable through the addition of
 Authentication TLVs [RFC5310] in the same way as Hellos or other
 IS-IS PDUs.

10. Code Points and Data Structures

 This section provides IANA considerations for this document and
 specifies the structures of the AppointmentBitmap, AppointmentList,
 VLAN-FGL Mapping Bit Map, and VLAN-FGL Mapping Pairs APPsub-TLVs.
 These APPsub-TLVs appear within a TRILL GENINFO TLV [RFC7357] in
 E-L1CS FS-LSPs [RFC7356].

10.1. IANA Considerations

 IANA has assigned four new APPsub-TLV type codes from the range below
 255 and entered them in the "TRILL APPsub-TLV Types under IS-IS TLV
 251 Application Identifier 1" registry as follows:
    Type   Name                 Reference
    ----   -----------------    ---------
    17     AppointmentBitmap    [RFC8139]
    18     AppointmentList      [RFC8139]
    19     FGL-VLAN-Bitmap      [RFC8139]
    20     FGL-VLAN-Pairs       [RFC8139]
 IANA has assigned a new RBridge Channel Protocol number in the range
 assigned by Standards Action [RFC5226] and updated the "RBridge
 Channel Protocols" registry as follows:
    Protocol  Description     Reference
    --------  --------------  ---------
     0x006    Port-Shutdown   [RFC8139]

Eastlake, et al. Standards Track [Page 28] RFC 8139 TRILL: Appointed Forwarders June 2017

 IANA has updated the reference for the "Hello reduction support" bit
 in the "PORT-TRILL-VER Sub-TLV Capability Flags" registry to refer to
 this document.

10.2. AppointmentBitmap APPsub-TLV

 The AppointmentBitmap APPsub-TLV provides an efficient method for a
 TRILL switch to indicate which TRILL switches it appoints as
 forwarders for which VLAN IDs when those VLAN IDs are relatively
 compact (that is, they do not span a large numeric range).  Such an
 appointment is only effective when the appointing TRILL switch is
 the DRB.
                            1 1 1 1 1 1
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Type                    |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Length                  |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Appointee Nickname      |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | RESV  |   Starting VLAN ID    |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |  Bit Map ...                      (variable)
       +-+-+-+-+-+-+-+-...
 o  Type: APPsub-TLV type, set to AppointmentBitmap sub-TLV 17.
 o  Length: 4 + size of bit map in bytes.  If Length is less than 4,
    the APPsub-TLV is corrupt and MUST be ignored.
 o  Appointee Nickname: The nickname of the TRILL switch being
    appointed as forwarder.
 o  RESV: 4 bits that MUST be sent as zero and ignored on receipt.
 o  Starting VLAN ID: The smallest VLAN ID to which the bits in the
    Bit Map correspond.
 o  Bit Map: A bit map of the VLANs for which the TRILL switch with
    Appointee Nickname is appointed as the forwarder.  The size of the
    bit map is length minus 4.  If the size of the bit map is zero,
    no appointments are made.

Eastlake, et al. Standards Track [Page 29] RFC 8139 TRILL: Appointed Forwarders June 2017

 Each bit in the Bit Map corresponds to a VLAN ID.  Bit 0 is for the
 VLAN whose ID appears in the Starting VLAN ID field.  Bit 1 is for
 that VLAN ID plus 1 (treating VLAN IDs as unsigned integers) and
 so on, with Bit N generally being Starting VLAN ID plus N.
 VLAN 0x000 and VLAN 0xFFF, or any larger ID, are invalid and are
 ignored.
 If the AppointmentBitmap APPsub-TLV is originated by the DRB on a
 link, it appoints the TRILL switch whose nickname appears in the
 Appointee Nickname field for the VLAN IDs corresponding to 1 bits in
 the Bit Map and revokes any Hello appointment of that TRILL switch
 for VLANs corresponding to 0 bits in the Bit Map.

10.3. AppointmentList APPsub-TLV

 The AppointmentList APPsub-TLV provides a convenient method for a
 TRILL switch to indicate which TRILL switches it appoints as
 forwarders for which VLAN IDs.  Such an appointment is only effective
 when the appointing TRILL switch is the DRB.
                            1 1 1 1 1 1
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Type                    |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Length                  |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Appointee Nickname      |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | RESV  |   VLAN ID 1           |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | RESV  |   VLAN ID 2           |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |  ...
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | RESV  |   VLAN ID k           |   (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 o  Type: APPsub-TLV type, set to AppointmentList sub-TLV 18.
 o  Length: 2 + 2 * k.  If Length is not an even number, the
    APPsub-TLV is corrupt and MUST be ignored.
 o  Appointee Nickname: The nickname of the TRILL switch being
    appointed as forwarder.

Eastlake, et al. Standards Track [Page 30] RFC 8139 TRILL: Appointed Forwarders June 2017

 o  RESV: 4 bits that MUST be sent as zero and ignored on receipt.
 o  VLAN ID: A 12-bit VLAN ID for which the appointee is being
    appointed as the forwarder.
 Type and Length are 2 bytes, because these are extended FS-LSPs.
 This APPsub-TLV, when originated by the DRB, appoints the TRILL
 switch with Appointee Nickname to be the Appointed Forwarder for the
 VLAN IDs listed.

10.4. FGL-VLAN-Bitmap APPsub-TLV

 The FGL-VLAN-Bitmap APPsub-TLV provides a method for a TRILL switch
 to indicate mappings of FGLs to VLAN IDs that it is configured to
 perform when egressing and ingressing native frames.
 The coding is efficient when both of the following apply:
  1. the VLAN IDs are compact (that is, they do not span a large

numeric range), and

  1. the FGLs and VLAN IDs are paired in a monotonically increasing

fashion.

                            1 1 1 1 1 1
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Type                    |                 (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |       Length                  |                 (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |  RESV |   Starting VLAN ID    |                 (2 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |   Starting FGL                                | (3 bytes)
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |  Bit Map ...                                   (variable)
       +-+-+-+-+-+-+-+-...
 o  Type: APPsub-TLV type, set to VLAN-FGL-Bitmap sub-TLV 19.
 o  Length: 5 + size of bit map in bytes.  If Length is less than 5,
    the APPsub-TLV is corrupt and MUST be ignored.
 o  RESV: 4 bits that MUST be sent as zero and ignored on receipt.

Eastlake, et al. Standards Track [Page 31] RFC 8139 TRILL: Appointed Forwarders June 2017

 o  Starting VLAN ID: Initial VLAN ID for the mapping information as
    discussed below.
 o  Starting FGL: Fine-Grained Label [RFC7172].
 o  Bit Map: Map of bits for VLAN-ID-to-FGL mappings.  The size of the
    bit map is Length minus 5.  If the size of the bit map is zero,
    no mappings are indicated.
 Each bit in the Bit Map corresponds to a VLAN ID and to an FGL.
 Bit 0 is for the VLAN whose ID appears in the Starting VLAN ID field
 and the Fine-Grained Label that appears in the FGL field.  Bit 1 is
 for that VLAN ID plus 1 and that FGL plus 1 (treating VLAN IDs and
 FGLs as unsigned integers) and so on, with Bit N generally being
 Starting VLAN ID plus N and FGL plus N.
 If a Bit Map bit is a 1, it indicates that the advertising TRILL
 switch will map between the corresponding VLAN ID and FGL on
 ingressing native frames and egressing TRILL Data packets if it is
 Appointed Forwarder for the VLAN.  If a Bit Map bit is a 0, it does
 not indicate any configured mapping of the VLAN ID to the FGL.
 However, VLAN ID 0x000 and VLAN ID 0xFFF or any larger ID are
 invalid, and FGLs larger than 0xFFFFFF are invalid; any Bit Map bits
 that correspond to an illegal VLAN ID or an illegal FGL are ignored.

10.5. FGL-VLAN-Pairs APPsub-TLV

 The FGL-VLAN-Pairs APPsub-TLV provides a method for a TRILL switch to
 indicate a list of the mappings of FGLs to VLAN IDs that it is
 configured to perform when egressing and ingressing native frames.
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |       Type                    |                 (2 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |       Length                  |                 (2 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-=-+-...-+-+-+
    |   Mapping RECORD 1                            | (5 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-=-+-...-+-+-+
    |   Mapping RECORD 2                            | (5 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-=-+-...-+-+-+
    |      ...
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-=-+-...-+-+-+
    |   Mapping RECORD k                            | (5 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-=-+-...-+-+-+

Eastlake, et al. Standards Track [Page 32] RFC 8139 TRILL: Appointed Forwarders June 2017

    Where a Mapping RECORD has the following structure:
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  RESV |   VLAN ID             |                 (2 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |       FGL                                     | (3 bytes)
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 o  Type: APPsub-TLV type, set to VLAN-FGL-Pairs sub-TLV 20.
 o  Length: 5 * k.  If Length is not a multiple of 5, the APPsub-TLV
    is corrupt and MUST be ignored.
 o  RESV: 4 bits that MUST be sent as zero and ignored on receipt.
 o  VLAN ID: 12-bit VLAN label.
 o  FGL: Fine-Grained Label [RFC7172].
 Each Mapping RECORD indicates that the originating TRILL switch is
 configured to map between the FGL and VLAN given on egressing and
 ingressing native frames.  However, VLAN ID 0x000 and VLAN ID 0xFFF
 are invalid; any Mapping RECORD that corresponds to an illegal
 VLAN ID is ignored.

11. Management Considerations

 This document primarily adds optional enhancements or optimizations.
 The only configuration parameters specified in this document are the
 number and frequency of copies of Port-Shutdown messages sent, as
 specified in Section 6.6.
 TRILL switch support of SNMPv3 is provided in the TRILL base protocol
 document [RFC6325].  MIBs have been specified in [RFC6850] and
 [RFC7784], but they do not include the configurable parameters
 specified herein.  It is anticipated that YANG modules will be
 specified for TRILL.

Eastlake, et al. Standards Track [Page 33] RFC 8139 TRILL: Appointed Forwarders June 2017

12. References

12.1. Normative References

 [802.1Q]   IEEE, "IEEE Standard for Local and metropolitan area
            networks--Bridges and Bridged Networks",
            IEEE Std 802.1Q-2014, DOI 10.1109/ieeestd.2014.6991462,
            <http://ieeexplore.ieee.org/
            servlet/opac?punumber=6991460>.
 [IS-IS]    ISO/IEC 10589:2002, Second Edition, "Intermediate System
            to Intermediate System Intra-Domain Routeing Exchange
            Protocol for use in Conjunction with the Protocol for
            Providing the Connectionless-mode Network Service
            (ISO 8473)", November 2002.
 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119,
            DOI 10.17487/RFC2119, March 1997,
            <http://www.rfc-editor.org/info/rfc2119>.
 [RFC6325]  Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and A.
            Ghanwani, "Routing Bridges (RBridges): Base Protocol
            Specification", RFC 6325, DOI 10.17487/RFC6325, July 2011,
            <http://www.rfc-editor.org/info/rfc6325>.
 [RFC6329]  Fedyk, D., Ed., Ashwood-Smith, P., Ed., Allan, D., Bragg,
            A., and P. Unbehagen, "IS-IS Extensions Supporting
            IEEE 802.1aq Shortest Path Bridging", RFC 6329,
            DOI 10.17487/RFC6329, April 2012,
            <http://www.rfc-editor.org/info/rfc6329>.
 [RFC7172]  Eastlake 3rd, D., Zhang, M., Agarwal, P., Perlman, R., and
            D. Dutt, "Transparent Interconnection of Lots of Links
            (TRILL): Fine-Grained Labeling", RFC 7172,
            DOI 10.17487/RFC7172, May 2014,
            <http://www.rfc-editor.org/info/rfc7172>.
 [RFC7176]  Eastlake 3rd, D., Senevirathne, T., Ghanwani, A., Dutt,
            D., and A. Banerjee, "Transparent Interconnection of Lots
            of Links (TRILL) Use of IS-IS", RFC 7176,
            DOI 10.17487/RFC7176, May 2014,
            <http://www.rfc-editor.org/info/rfc7176>.
 [RFC7177]  Eastlake 3rd, D., Perlman, R., Ghanwani, A., Yang, H., and
            V. Manral, "Transparent Interconnection of Lots of Links
            (TRILL): Adjacency", RFC 7177, DOI 10.17487/RFC7177,
            May 2014, <http://www.rfc-editor.org/info/rfc7177>.

Eastlake, et al. Standards Track [Page 34] RFC 8139 TRILL: Appointed Forwarders June 2017

 [RFC7178]  Eastlake 3rd, D., Manral, V., Li, Y., Aldrin, S., and D.
            Ward, "Transparent Interconnection of Lots of Links
            (TRILL): RBridge Channel Support", RFC 7178,
            DOI 10.17487/RFC7178, May 2014,
            <http://www.rfc-editor.org/info/rfc7178>.
 [RFC7356]  Ginsberg, L., Previdi, S., and Y. Yang, "IS-IS Flooding
            Scope Link State PDUs (LSPs)", RFC 7356,
            DOI 10.17487/RFC7356, September 2014,
            <http://www.rfc-editor.org/info/rfc7356>.
 [RFC7357]  Zhai, H., Hu, F., Perlman, R., Eastlake 3rd, D., and O.
            Stokes, "Transparent Interconnection of Lots of Links
            (TRILL): End Station Address Distribution Information
            (ESADI) Protocol", RFC 7357, DOI 10.17487/RFC7357,
            September 2014, <http://www.rfc-editor.org/info/rfc7357>.
 [RFC7780]  Eastlake 3rd, D., Zhang, M., Perlman, R., Banerjee, A.,
            Ghanwani, A., and S. Gupta, "Transparent Interconnection
            of Lots of Links (TRILL): Clarifications, Corrections, and
            Updates", RFC 7780, DOI 10.17487/RFC7780, February 2016,
            <http://www.rfc-editor.org/info/rfc7780>.
 [RFC7978]  Eastlake 3rd, D., Umair, M., and Y. Li, "Transparent
            Interconnection of Lots of Links (TRILL): RBridge Channel
            Header Extension", RFC 7978, DOI 10.17487/RFC7978,
            September 2016, <http://www.rfc-editor.org/info/rfc7978>.
 [RFC7981]  Ginsberg, L., Previdi, S., and M. Chen, "IS-IS Extensions
            for Advertising Router Information", RFC 7981,
            DOI 10.17487/RFC7981, October 2016,
            <http://www.rfc-editor.org/info/rfc7981>.
 [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in
            RFC 2119 Key Words", BCP 14, RFC 8174,
            DOI 10.17487/RFC8174, May 2017,
            <http://www.rfc-editor.org/info/rfc8174>.

Eastlake, et al. Standards Track [Page 35] RFC 8139 TRILL: Appointed Forwarders June 2017

12.2. Informative References

 [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
            IANA Considerations Section in RFCs", BCP 26, RFC 5226,
            DOI 10.17487/RFC5226, May 2008,
            <http://www.rfc-editor.org/info/rfc5226>.
 [RFC5310]  Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
            and M. Fanto, "IS-IS Generic Cryptographic
            Authentication", RFC 5310, DOI 10.17487/RFC5310,
            February 2009, <http://www.rfc-editor.org/info/rfc5310>.
 [RFC6439]  Perlman, R., Eastlake, D., Li, Y., Banerjee, A., and F.
            Hu, "Routing Bridges (RBridges): Appointed Forwarders",
            RFC 6439, DOI 10.17487/RFC6439, November 2011,
            <http://www.rfc-editor.org/info/rfc6439>.
 [RFC6850]  Rijhsinghani, A. and K. Zebrose, "Definitions of Managed
            Objects for Routing Bridges (RBridges)", RFC 6850,
            DOI 10.17487/RFC6850, January 2013,
            <http://www.rfc-editor.org/info/rfc6850>.
 [RFC7379]  Li, Y., Hao, W., Perlman, R., Hudson, J., and H. Zhai,
            "Problem Statement and Goals for Active-Active Connection
            at the Transparent Interconnection of Lots of Links
            (TRILL) Edge", RFC 7379, DOI 10.17487/RFC7379,
            October 2014, <http://www.rfc-editor.org/info/rfc7379>.
 [RFC7784]  Kumar, D., Salam, S., and T. Senevirathne, "Transparent
            Interconnection of Lots of Links (TRILL) Operations,
            Administration, and Maintenance (OAM) MIB", RFC 7784,
            DOI 10.17487/RFC7784, February 2016,
            <http://www.rfc-editor.org/info/rfc7784>.

Eastlake, et al. Standards Track [Page 36] RFC 8139 TRILL: Appointed Forwarders June 2017

Appendix A. VLAN Inhibition Example

 The per-VLAN inhibition timers (or the equivalent) are needed to be
 loop safe in the case of misconfigured bridges on a link.
 For a simple example, assume that RB1 and RB2 are the only RBridges
 on the link, that RB1 is higher priority to be the DRB, and that they
 both want VLAN 1 (the default) to be the Designated VLAN.  However,
 there is a bridge between them configured so that RB1 can see all the
 frames sent by RB2 but none of the frames from RB1 can get through
 to RB2.
 Both will think they are the DRB: RB1 because it is higher priority
 even though it sees the Hellos from RB2, and RB2 because it doesn't
 see the Hellos from RB1 and therefore thinks it is highest priority.
 Say RB1 chooses to act as Appointed Forwarder for VLANs 2 and 3 while
 RB2 chooses to act as Appointed Forwarder for VLANs 3 and 4.  There
 is no problem with VLANs 2 and 4, but if you do not do something
 about it, you could have a loop involving VLAN 3.  RB1 will see the
 Hellos that RB2 issues on VLAN 3 declaring itself Appointed
 Forwarder, so RB1 will be inhibited on VLAN 3.  RB2 does not see the
 Hellos issued by RB1 on VLAN 3, so RB2 will become uninhibited and
 will handle VLAN 3 native traffic.
 However, this situation may change.  RB2 might crash, the bridge
 might crash, RB2 might be reconfigured so it no longer tried to act
 as Appointed Forwarder for VLAN 3, or other issues may occur.  So,
 RB1 has to maintain a VLAN 3 inhibition timer, and if it sees
 no Hellos from any other RBridge on the link claiming to be Appointed
 Forwarder for VLAN 3 for a long enough time, then RB1 becomes
 uninhibited for that VLAN on the port in question and can handle
 end-station traffic in VLAN 3.

Eastlake, et al. Standards Track [Page 37] RFC 8139 TRILL: Appointed Forwarders June 2017

Appendix B. Multi-Link VLAN Mapping Loop Example

 Assume that RBridges RB1 and RB2 have ports P1 and P2, respectively,
 that are both on Link L1 and that RBridges RB3 and RB4 have ports P3
 and P4, respectively, that are both on Link L2.  Assume further that
 P1 and P3 are Appointed Forwarders for VLAN-x and P2 and P4 are
 Appointed Forwarders for VLAN-y.  This situation is shown in the
 figure below.
        + - - - - - - - - - - - - - - - - - - - - - +
        |                                           |
        |                TRILL network              |
        |                                           |
        |  +---+   +---+             +---+   +---+  |
        + -|RB1|- -|RB2|- - - - - - -|RB3|- -|RB4|- +
           +---+   +---+             +---+   +---+
          P1|       P2|             P3|       P4|
            |         |               |         |
            |x        |y              |x        |y
            |   +-+   |               |   +-+   |
      L1 ---+---|M|---+--+---   L2 ---+---|M|---+---
                +-+      |                +-+
                       +---+
                       |ES1|
                       +---+
 Further assume that L1 and L2 are each bridged LANs that include a
 device M, presumably a bridge, that maps VLAN-x into VLAN-y and
 VLAN-y into VLAN-x.
 If end station ES1 originated a broadcast or other multi-destination
 frame in VLAN-y, it would be ingressed by RB2.  (The frame would also
 be mapped to VLAN-x and ingressed by RB1, but we initially ignore
 that.)  RB2 will flood the resulting TRILL Data packet through the
 campus, and, at least in the broadcast and unknown unicast cases,
 it will get to RB4, where it will be egressed to L2.  Inside L2, this
 broadcast frame is mapped to VLAN-x and then ingressed by RB3.  RB3
 then floods the resulting TRILL Data packet through the campus, this
 time with an Inner.VLAN of VLAN-x, as a result of which it will be
 egressed by RB1 into L1.  Inside L1, it will be mapped back to VLAN-y
 and then ingressed by RB2, completing the loop.  The packet will loop
 indefinitely, because in native form on L1 and L2 it has no TRILL
 Hop Count, and an indefinitely large number of copies will be
 delivered to ES1 and any other end station so situated.  The same
 problem would occur even if P1 and P2 were on the same RBridge and/or
 P3 and P4 were on the same RBridge.  Actually, because the original
 frame was also mapped to VLAN-x inside L1 and ingressed by RB1, there
 are two copies looping around in opposite directions.

Eastlake, et al. Standards Track [Page 38] RFC 8139 TRILL: Appointed Forwarders June 2017

 The use of Fine-Grained Labels [RFC7172] complicates but does not
 essentially change the potential problem.
 This example shows why VLAN mapping between Appointed Forwarder ports
 on a TRILL link is loop unsafe.  When such a situation is detected,
 the DRB on the link changes Appointed Forwarders as necessary to
 assure that a single RBridge port is Appointed Forwarder for all
 VLANs involved in mapping.  This change makes the situation
 loop safe.

Appendix C. Changes to RFCs 6325, 6439, and 7177

 This document updates [RFC6325], obsoletes [RFC6439], and updates
 [RFC7177].
 The change to [RFC6325], the TRILL base protocol, is as follows:
    Addition of mandatory support for E-L1CS FS-LSPs.
 Changes to [RFC6439], which this document obsoletes, are as follows:
 1. Specification of APPsub-TLVs and procedures to be used in
    E-L1CS FS-LSP forwarder appointments.
 2. Incorporation of updates to [RFC6439] that appeared in Section 10
    of RFC 7180, which has been obsoleted by [RFC7780].  They appear
    primarily in Section 4 of this document.
 3. Addition of an optional FGL-VLAN consistency check feature,
    including specification of APPsub-TLVs.
 4. Deletion of references to the October 2011 version of the document
    "RBridges: Campus VLAN and Priority Regions"
    (draft-ietf-trill-rbridge-vlan-mapping), which has been dropped by
    the TRILL WG.
 5. Addition of the Port-Shutdown message.
 6. Elimination of the requirement that the DRB not send appointments
    in Hellos until its DRB inhibition timer has expired.  This was an
    unnecessary safety precaution that is pointless, given that
    appointments in E-L1CS FS-LSPs are immediately visible.
 7. Addition of three optional methods (Section 3.2) to optimize
    (reduce) inhibition time under various circumstances.
 8. Editorial changes.

Eastlake, et al. Standards Track [Page 39] RFC 8139 TRILL: Appointed Forwarders June 2017

 Changes to [RFC7177] are as follows:
    As provided in Section 6, TRILL switches SHOULD treat the
    reception of a Port-Shutdown RBridge Channel message from RB1
    listing port P1 as if it were an event A3 as specified in
    [RFC7177], resulting in transition of any adjacency to P1 to the
    Detect state.

Acknowledgments

 The following are hereby thanked for their contributions to this
 document:
    Spencer Dawkins, Shawn M. Emery, Stephen Farrell, Joel Halpern,
    Sue Hares, Christer Holmberg, Gayle Noble, Alvaro Retana, Dan
    Romascanu, and Mingui Zhang.
 The following are thanked for their contributions to [RFC6439], the
 predecessor to this document:
    Ron Bonica, Stewart Bryant, Linda Dunbar, Les Ginsberg, Erik
    Nordmark, Dan Romascanu, and Mike Shand.
    We also thank Radia Perlman, who coauthored [RFC6439].

Eastlake, et al. Standards Track [Page 40] RFC 8139 TRILL: Appointed Forwarders June 2017

Authors' Addresses

 Donald Eastlake 3rd
 Huawei Technologies
 155 Beaver Street
 Milford, MA  01757
 United States of America
 Phone: +1-508-333-2270
 Email: d3e3e3@gmail.com
 Yizhou Li
 Huawei Technologies
 101 Software Avenue
 Nanjing  210012
 China
 Phone: +86-25-56622310
 Email: liyizhou@huawei.com
 Mohammed Umair
 IP Infusion
 Email: mohammed.umair2@ipinfusion.com
 Ayan Banerjee
 Cisco Systems
 170 West Tasman Drive
 San Jose, CA  95134
 United States of America
 Phone: +1-408-333-7149
 Email: ayabaner@cisco.com
 Fangwei Hu
 ZTE Corporation
 889 Bibo Road
 Shanghai  201203
 China
 Phone: +86-21-68896273
 Email: hu.fangwei@zte.com.cn

Eastlake, et al. Standards Track [Page 41]

/data/webs/external/dokuwiki/data/pages/rfc/rfc8139.txt · Last modified: 2017/06/09 04:56 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki