GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc8100

Internet Engineering Task Force (IETF) R. Geib, Ed. Request for Comments: 8100 Deutsche Telekom Category: Informational D. Black ISSN: 2070-1721 Dell EMC

                                                            March 2017
           Diffserv-Interconnection Classes and Practice

Abstract

 This document defines a limited common set of Diffserv Per-Hop
 Behaviors (PHBs) and Diffserv Codepoints (DSCPs) to be applied at
 (inter)connections of two separately administered and operated
 networks, and it explains how this approach can simplify network
 configuration and operation.  Many network providers operate
 Multiprotocol Label Switching (MPLS) using Treatment Aggregates for
 traffic marked with different Diffserv Per-Hop Behaviors and use MPLS
 for interconnection with other networks.  This document offers a
 simple interconnection approach that may simplify operation of
 Diffserv for network interconnection among providers that use MPLS
 and apply the Short Pipe Model.  While motivated by the requirements
 of MPLS network operators that use Short Pipe Model tunnels, this
 document is applicable to other networks, both MPLS and non-MPLS.

Status of This Memo

 This document is not an Internet Standards Track specification; it is
 published for informational purposes.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Not all documents
 approved by the IESG are a candidate for any level of Internet
 Standard; see Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc8100.

Geib & Black Informational [Page 1] RFC 8100 Diffserv-Intercon March 2017

Copyright Notice

 Copyright (c) 2017 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Table of Contents

 1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   1.1.  Related Work  . . . . . . . . . . . . . . . . . . . . . .   4
   1.2.  Applicability Statement . . . . . . . . . . . . . . . . .   5
   1.3.  Document Organization . . . . . . . . . . . . . . . . . .   5
 2.  MPLS and Short Pipe Model Tunnels . . . . . . . . . . . . . .   6
 3.  Relationship to RFC 5127  . . . . . . . . . . . . . . . . . .   7
   3.1.  Background of RFC 5127  . . . . . . . . . . . . . . . . .   7
   3.2.  Differences from RFC 5127 . . . . . . . . . . . . . . . .   7
 4.  The Diffserv-Intercon Interconnection Classes . . . . . . . .   8
   4.1.  Diffserv-Intercon Example . . . . . . . . . . . . . . . .  11
   4.2.  End-to-End PHB and DSCP Transparency  . . . . . . . . . .  13
   4.3.  Treatment of Network Control Traffic at Carrier
         Interconnection Interfaces  . . . . . . . . . . . . . . .  13
 5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  15
 6.  Security Considerations . . . . . . . . . . . . . . . . . . .  15
 7.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  16
   7.1.  Normative References  . . . . . . . . . . . . . . . . . .  16
   7.2.  Informative References  . . . . . . . . . . . . . . . . .  16
 Appendix A.  The MPLS Short Pipe Model and IP Traffic . . . . . .  18
 Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . .  21
 Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  21

Geib & Black Informational [Page 2] RFC 8100 Diffserv-Intercon March 2017

1. Introduction

 Diffserv has been deployed in many networks; it provides
 differentiated traffic forwarding based on the Diffserv Codepoint
 (DSCP) field, which is part of the IP header [RFC2474].  This
 document defines a set of common Diffserv classes (Per-Hop Behaviors
 (PHBs)) and codepoints for use at interconnection points to which and
 from which locally used classes and codepoints should be mapped.
 As described by Section 2.3.4.2 of [RFC2475], the re-marking of
 packets at domain boundaries is a Diffserv feature.  If traffic
 marked with unknown or unexpected DSCPs is received, [RFC2474]
 recommends forwarding that traffic with default (best-effort)
 treatment without changing the DSCP markings to better support
 incremental Diffserv deployment in existing networks as well as with
 routers that do not support Diffserv or are not configured to support
 it.  Many networks do not follow this recommendation and instead
 re-mark unknown or unexpected DSCPs to zero upon receipt for default
 (best-effort) forwarding in accordance with the guidance in [RFC2475]
 to ensure that appropriate DSCPs are used within a Diffserv domain.
 This document is based on the latter approach and defines additional
 DSCPs that are known and expected at network interconnection
 interfaces in order to reduce the amount of traffic whose DSCPs are
 re-marked to zero.
 This document is motivated by requirements for IP network
 interconnection with Diffserv support among providers that operate
 Multiprotocol Label Switching (MPLS) in their backbones, but it is
 also applicable to other technologies.  The operational
 simplifications and methods in this document help align IP Diffserv
 functionality with MPLS limitations resulting from the widely
 deployed Short Pipe Model for MPLS tunnel operation [RFC3270].
 Further, limiting Diffserv to a small number of Treatment Aggregates
 can enable network traffic to leave a network with the DSCP value
 with which it was received, even if a different DSCP is used within
 the network, thus providing an opportunity to extend consistent
 Diffserv treatment across network boundaries.
 In isolation, use of a defined set of interconnection PHBs and DSCPs
 may appear to be additional effort for a network operator.  The
 primary offsetting benefit is that mapping from or to the
 interconnection PHBs and DSCPs is specified once for all of the
 interconnections to other networks that can use this approach.
 Absent this approach, the PHBs and DSCPs have to be negotiated and
 configured independently for each network interconnection, which has
 poor administrative and operational scaling properties.  Further,

Geib & Black Informational [Page 3] RFC 8100 Diffserv-Intercon March 2017

 consistent end-to-end Diffserv treatment is more likely to result
 when an interconnection codepoint scheme is used because traffic is
 re-marked to the same DSCPs at all network interconnections.
 The interconnection approach described in this document (referred to
 as "Diffserv-Intercon") uses a set of PHBs (mapped to four
 corresponding MPLS Treatment Aggregates) along with a set of
 interconnection DSCPs allowing straightforward rewriting to domain-
 internal DSCPs and defined DSCP markings for traffic forwarded to
 interconnected domains.  The solution described here can be used in
 other contexts benefiting from a defined Diffserv interconnection
 interface.
 The basic idea is that traffic sent with a Diffserv-Intercon PHB and
 DSCP is restored to that PHB and DSCP at each network
 interconnection, even though a different PHB and DSCP may be used
 within each network involved.  The key requirement is that the
 network ingress interconnect DSCP be restored at the network egress,
 and a key observation is that this is only feasible in general for a
 small number of DSCPs.  Traffic sent with other DSCPs can be
 re-marked to an interconnect DSCP or dealt with via an additional
 agreement(s) among the operators of the interconnected networks; use
 of the MPLS Short Pipe Model favors re-marking unexpected DSCPs to
 zero in the absence of an additional agreement(s), as explained
 further in this document.
 In addition to the common interconnecting PHBs and DSCPs,
 interconnecting operators need to further agree on the tunneling
 technology used for interconnection (e.g., MPLS, if used) and control
 or mitigate the impacts of tunneling on reliability and MTU.

1.1. Related Work

 In addition to the activities that triggered this work, there are
 additional RFCs and Internet-Drafts that may benefit from an
 interconnection PHB and DSCP scheme.  [RFC5160] suggests
 Meta-QoS-Classes to help enable deployment of standardized end-to-end
 QoS classes.  The Diffserv-Intercon class and codepoint scheme is
 intended to complement that work (e.g., by enabling a defined set of
 interconnection DSCPs and PHBs).
 Border Gateway Protocol (BGP) support for signaling Class of Service
 at interconnection interfaces [BGP-INTERCONNECTION] [SLA-EXCHANGE] is
 complementary to Diffserv-Intercon.  These two BGP documents focus on
 exchanging Service Level Agreement (SLA) and traffic conditioning
 parameters and assume that common PHBs identified by the signaled
 DSCPs have been established (e.g., via use of the Diffserv-Intercon
 DSCPs) prior to BGP signaling of PHB id codes.

Geib & Black Informational [Page 4] RFC 8100 Diffserv-Intercon March 2017

1.2. Applicability Statement

 This document is applicable to the use of Differentiated Services for
 interconnection traffic between networks and is particularly suited
 to interconnection of MPLS-based networks that use MPLS Short Pipe
 Model tunnels.  This document is also applicable to other network
 technologies, but it is not intended for use within an individual
 network, where the approach specified in [RFC5127] is among the
 possible alternatives; see Section 3 for further discussion.
 The Diffserv-Intercon approach described in this document simplifies
 IP-based interconnection to domains operating the MPLS Short Pipe
 Model for IP traffic, both terminating within the domain and
 transiting onward to another domain.  Transiting traffic is received
 and sent with the same PHB and DSCP.  Terminating traffic maintains
 the PHB with which it was received; however, the DSCP may change.
 Diffserv-Intercon is also applicable to Pipe Model tunneling
 [RFC2983] [RFC3270], but it is not applicable to Uniform Model
 tunneling [RFC2983] [RFC3270].
 The Diffserv-Intercon approach defines a set of four PHBs for support
 at interconnections (or network boundaries in general).
 Corresponding DSCPs for use at an interconnection interface are also
 defined.  Diffserv-Intercon allows for a simple mapping of PHBs and
 DSCPs to MPLS Treatment Aggregates.  It is extensible by IETF
 standardization, and this allows additional PHBs and DSCPs to be
 specified for the Diffserv-Intercon scheme.  Coding space for private
 interconnection agreements or provider internal services is
 available, as only a single digit number of standard DSCPs are
 applied by the Diffserv-Intercon approach.

1.3. Document Organization

 This document is organized as follows: Section 2 reviews the MPLS
 Short Pipe Model for Diffserv Tunnels [RFC3270], because effective
 support for that model is a crucial goal of Diffserv-Intercon.
 Section 3 provides background on the approach described in RFC 5127
 to Traffic Class (TC) aggregation within a Diffserv network domain
 and contrasts it with the Diffserv-Intercon approach.  Section 4
 introduces Diffserv-Intercon Treatment Aggregates, along with the
 PHBs and DSCPs that they use, and explains how other PHBs (and
 associated DSCPs) may be mapped to these Treatment Aggregates.
 Section 4 also discusses treatment of IP traffic, MPLS VPN Diffserv
 considerations, and the handling of high-priority network management
 traffic.  Appendix A describes how the MPLS Short Pipe Model
 (Penultimate Hop Popping (PHP)) impacts DSCP marking for IP
 interconnections.

Geib & Black Informational [Page 5] RFC 8100 Diffserv-Intercon March 2017

2. MPLS and Short Pipe Model Tunnels

 This section provides a summary of the implications of MPLS Short
 Pipe Model tunnels and, in particular, their use of PHP (see RFC
 3270) on the Diffserv tunnel framework described in RFC 2983.  The
 Pipe and Uniform Models for Differentiated Services and Tunnels are
 defined in [RFC2983].  RFC 3270 adds the Short Pipe Model to reflect
 the impact of MPLS PHP, primarily for MPLS-based IP tunnels and VPNs.
 The Short Pipe Model and PHP have subsequently become popular with
 network providers that operate MPLS networks and are now widely used
 to transport unencapsulated IP traffic.  This has important
 implications for Diffserv functionality in MPLS networks.
 Per RFC 2474, the recommendation to forward traffic with unrecognized
 DSCPs with default (best-effort) service without rewriting the DSCP
 has not been widely deployed in practice.  Network operation and
 management are simplified when there is a 1-1 match between the DSCP
 marked on the packet and the forwarding treatment (PHB) applied by
 network nodes.  When this is done, CS0 (the all-zero DSCP) is the
 only DSCP used for default forwarding of best-effort traffic, and a
 common practice is to re-mark to CS0 any traffic received with
 unrecognized or unsupported DSCPs at network edges.
 MPLS networks are more subtle in this regard, as it is possible to
 encode the provider's DSCP in the MPLS TC field and allow that to
 differ from the PHB indicated by the DSCP in the MPLS-encapsulated IP
 packet.  If the MPLS label with the provider's TC field is present at
 all hops within the provider network, this approach would allow an
 unrecognized DSCP to be carried edge-to-edge over an MPLS network,
 because the effective DSCP used by the provider's MPLS network would
 be encoded in the MPLS label TC field (and also carried
 edge-to-edge).  Unfortunately, this is only true for Pipe Model
 tunnels.
 Short Pipe Model tunnels and PHP behave differently because PHP
 removes and discards the MPLS provider label carrying the provider's
 TC field before the traffic exits the provider's network.  That
 discard occurs one hop upstream of the MPLS tunnel endpoint (which is
 usually at the network edge), resulting in no provider TC information
 being available at the tunnel egress.  To ensure consistent handling
 of traffic at the tunnel egress, the DSCP field in the MPLS-
 encapsulated IP header has to contain a DSCP that is valid for the
 provider's network, so that the IP header cannot be used to carry a
 different DSCP edge-to-edge.  See Appendix A for a more detailed
 discussion.

Geib & Black Informational [Page 6] RFC 8100 Diffserv-Intercon March 2017

3. Relationship to RFC 5127

 This document draws heavily upon the approach to aggregation of
 Diffserv TCs for use within a network as described in RFC 5127, but
 there are important differences caused by characteristics of network
 interconnects that differ from links within a network.

3.1. Background of RFC 5127

 Many providers operate MPLS-based backbones that employ backbone
 traffic engineering to ensure that if a major link, switch, or router
 fails, the result will be a routed network that continues to
 function.  Based on that foundation, [RFC5127] introduced the concept
 of Diffserv Treatment Aggregates, which enable traffic marked with
 multiple DSCPs to be forwarded in a single MPLS TC based on robust
 provider backbone traffic engineering.  This enables differentiated
 forwarding behaviors within a domain in a fashion that does not
 consume a large number of MPLS TCs.
 RFC 5127 provides an example aggregation of Diffserv service classes
 into four Treatment Aggregates.  A small number of aggregates are
 used because:
 o  The available coding space for carrying TC information (e.g.,
    Diffserv PHB) in MPLS (and Ethernet) is only 3 bits in size and is
    intended for more than just Diffserv purposes (see, e.g.,
    [RFC5129]).
 o  The common interconnection DSCPs ought not to use all 8 possible
    values.  This leaves space for future standards, private bilateral
    agreements, and local use PHBs and DSCPs.
 o  Migrations from one DSCP scheme to a different one is another
    possible application of otherwise unused DSCPs.

3.2. Differences from RFC 5127

 Like RFC 5127, this document also uses four Treatment Aggregates, but
 it differs from RFC 5127 in some important ways:
 o  It follows RFC 2475 in allowing the DSCPs used within a network to
    differ from those used to exchange traffic with other networks (at
    network edges), but it provides support to restore ingress DSCP
    values if one of the recommended interconnect DSCPs in this
    document is used.  This results in DSCP re-marking at both network
    ingress and network egress, and this document assumes that such
    re-marking at network edges is possible for all interface types.

Geib & Black Informational [Page 7] RFC 8100 Diffserv-Intercon March 2017

 o  Diffserv-Intercon suggests limiting the number of interconnection
    PHBs per Treatment Aggregate to the minimum required.  As further
    discussed below, the number of PHBs per Treatment Aggregate is no
    more than two.  When two PHBs are specified for a Diffserv-
    Intercon Treatment Aggregate, the expectation is that the provider
    network supports DSCPs for both PHBs but uses a single MPLS TC for
    the Treatment Aggregate that contains the two PHBs.
 o  Diffserv-Intercon suggests mapping other PHBs and DSCPs into the
    interconnection Treatment Aggregates as further discussed below.
 o  Diffserv-Intercon treats network control (NC) traffic as a special
    case.  Within a provider's network, the CS6 DSCP is used for local
    network control traffic (routing protocols and Operations,
    Administration, and Maintenance (OAM) traffic that is essential to
    network operation administration, control, and management) that
    may be destined for any node within the network.  In contrast,
    network control traffic exchanged between networks (e.g., BGP)
    usually terminates at or close to a network edge and is not
    forwarded through the network because it is not part of internal
    routing or OAM for the receiving network.  In addition, such
    traffic is unlikely to be covered by standard interconnection
    agreements; rather, it is more likely to be specifically
    configured (e.g., most networks impose restrictions on use of BGP
    with other networks for obvious reasons).  See Section 4.2 for
    further discussion.
 o  Because RFC 5127 used a Treatment Aggregate for network control
    traffic, Diffserv-Intercon can instead define a fourth Treatment
    Aggregate for use at network interconnections instead of the
    Network Control Treatment Aggregate in RFC 5127.  Network control
    traffic may still be exchanged across network interconnections as
    further discussed in Section 4.2.  Diffserv-Intercon uses this
    fourth Treatment Aggregate for Voice over IP (VoIP) traffic, where
    network-provided service differentiation is crucial, as even minor
    glitches are immediately apparent to the humans involved in the
    conversation.

4. The Diffserv-Intercon Interconnection Classes

 At an interconnection, the networks involved need to agree on the
 PHBs used for interconnection and the specific DSCP for each PHB.
 This document defines a set of four interconnection Treatment
 Aggregates with well-defined DSCPs to be aggregated by them.  A
 sending party re-marks DSCPs from internal usage to the
 interconnection codepoints.  The receiving party re-marks DSCPs to
 their internal usage.  The interconnect SLA defines the set of DSCPs
 and PHBs supported across the two interconnected domains and the

Geib & Black Informational [Page 8] RFC 8100 Diffserv-Intercon March 2017

 treatment of PHBs and DSCPs that are not recognized by the receiving
 domain.
 Similar approaches that use a small number of Treatment Aggregates
 (including recognition of the importance of VoIP traffic) have been
 taken in related standards and recommendations from outside the IETF,
 e.g., Y.1566 [Y.1566], Global System for Mobile Communications
 Association (GSMA) IR.34 [IR.34], and MEF23.1 [MEF23.1].
 The list of the four Diffserv-Intercon Treatment Aggregates follows,
 highlighting differences from RFC 5127 and suggesting mappings for
 all RFC 4594 TCs to Diffserv-Intercon Treatment Aggregates:
 Telephony Service Treatment Aggregate:  PHB Expedited Forwarding
         (EF), DSCP 101 110 and PHB VOICE-ADMIT, DSCP 101 100 (see
         [RFC3246], [RFC4594], and [RFC5865]).  This Treatment
         Aggregate corresponds to the Real-Time Treatment Aggregate
         definition regarding the queuing (both delay and jitter
         should be minimized) per RFC 5127, but this aggregate is
         restricted to transport Telephony service class traffic in
         the sense of [RFC4594].
 Bulk Real-Time Treatment Aggregate:  This Treatment Aggregate is
         designed to transport PHB AF41, DSCP 100 010 (the other AF4
         PHB group PHBs and DSCPs may be used for future extension of
         the set of DSCPs carried by this Treatment Aggregate).  This
         Treatment Aggregate is intended to provide Diffserv-Intercon
         network interconnection of a subset of the Real-Time
         Treatment Aggregate defined in RFC 5127, specifically the
         portions that consume significant bandwidth.  This traffic is
         expected to consist of the following classes defined in RFC
         4594: Broadcast Video, Real-Time Interactive, and Multimedia
         Conferencing.  This Treatment Aggregate should be configured
         with a rate-based queue (consistent with the recommendation
         for the transported TCs in RFC 4594).  By comparison to RFC
         5127, the number of DSCPs has been reduced to one
         (initially).  The AF42 and AF43 PHBs could be added if there
         is a need for three-color marked Multimedia Conferencing
         traffic.
 Assured Elastic Treatment Aggregate:  This Treatment Aggregate
         consists of PHBs AF31 and AF32 (i.e., DSCPs 011 010 and 011
         100).  By comparison to RFC 5127, the number of DSCPs has
         been reduced to two.  This document suggests to transport
         signaling marked by AF31 (e.g., as recommended by GSMA IR.34
         [IR.34]).  AF33 is reserved for the extension of PHBs to be
         aggregated by this Treatment Aggregate.  For Diffserv-
         Intercon network interconnection, the following service

Geib & Black Informational [Page 9] RFC 8100 Diffserv-Intercon March 2017

         classes (per RFC 4594) should be mapped to the Assured
         Elastic Treatment Aggregate: the Signaling service class
         (being marked for lowest loss probability), the Multimedia
         Streaming service class, the Low-Latency Data service class,
         and the High-Throughput Data service class.
 Default / Elastic Treatment Aggregate:   Transports the Default PHB,
         CS0 with DSCP 000 000.  An example in RFC 5127 refers to this
         Treatment Aggregate as "Elastic Treatment Aggregate".  An
         important difference from RFC 5127 is that any traffic with
         unrecognized or unsupported DSCPs may be re-marked to this
         DSCP.  For Diffserv-Intercon network interconnection, the
         Standard service class and Low-Priority Data service class
         defined in RFC 4594 should be mapped to this Treatment
         Aggregate.  This document does not specify an interconnection
         class for Low-Priority Data (also defined RFC 4594).  This
         traffic may be forwarded with a Lower Effort PHB in one
         domain (e.g., the PHB proposed by Informational [RFC3662]),
         but the methods specified in this document re-mark this
         traffic with DSCP CS0 at a Diffserv-Intercon network
         interconnection.  This has the effect that Low-Priority Data
         is treated the same as data sent using the Standard service
         class.  (Note: In a network that implements RFC 2474, Low-
         Priority traffic marked as CS1 would otherwise receive better
         treatment than Standard traffic using the default PHB.)
 RFC 2475 states that ingress nodes must condition all inbound traffic
 to ensure that the DS codepoints are acceptable; packets found to
 have unacceptable codepoints must either be discarded or have their
 DS codepoints modified to acceptable values before being forwarded.
 For example, an ingress node receiving traffic from a domain with
 which no enhanced service agreement exists may reset the DS codepoint
 to CS0.  As a consequence, an interconnect SLA needs to specify not
 only the treatment of traffic that arrives with a supported
 interconnect DSCP but also the treatment of traffic that arrives with
 unsupported or unexpected DSCPs; re-marking to CS0 is a widely
 deployed behavior.
 During the process of setting up a Diffserv interconnection, both
 networks should define the set of acceptable and unacceptable DSCPs
 and specify the treatment of traffic marked with each DSCP.
 While Diffserv-Intercon allows modification of unacceptable DSCPs, if
 traffic using one or more of the PHBs in a PHB group (e.g., AF3x,
 consisting of AF31, AF32, and AF33) is accepted as part of a
 supported Diffserv-Intercon Treatment Aggregate, then traffic using
 other PHBs from the same PHB group should not be modified to use PHBs
 outside of that PHB group and, in particular, should not be re-marked

Geib & Black Informational [Page 10] RFC 8100 Diffserv-Intercon March 2017

 to CS0 unless the entire PHB group is re-marked to CS0.  This avoids
 unexpected forwarding behavior (and potential reordering; see also
 [RFC7657]) when using Assured Forwarding (AF) PHBs [RFC2597].

4.1. Diffserv-Intercon Example

 The overall approach to DSCP marking at network interconnections is
 illustrated by the following example.  Provider O, provider W, and
 provider F are peered with provider T.  They have agreed upon a
 Diffserv interconnection SLA.
 Traffic of provider O terminates within provider T's network, while
 provider W's traffic transits through the network of provider T to
 provider F.  This example assumes that all providers use their own
 internal PHB and codepoint (DSCP) that correspond to the AF31 PHB in
 the Diffserv-Intercon Assured Elastic Treatment Aggregate (AF21, CS2,
 and AF11 are used in the example).

Geib & Black Informational [Page 11] RFC 8100 Diffserv-Intercon March 2017

  Provider O            Provider W
        |                      |
   +----------+           +----------+
   |   AF21   |           |   CS2    |
   +----------+           +----------+
        V                      V
    +~~~~~~~+              +~~~~~~~+
    |Rtr PrO|              |Rtr PrW|               Rtr:   Router
    +~~~~~~~+              +~~~~~~~+             Pr[L]:   Provider[L]
        |        Diffserv      |
   +----------+           +----------+
   |   AF31   |           |   AF31   |
   +----------+           +----------+
        V        Intercon      V
    +~~~~~~~+                  |
    |RtrPrTI|------------------+            Router Provider T Ingress
    +~~~~~~~+
        |            Provider T Domain
   +------------------+
   | MPLS TC 2, AF21  |
   +------------------+
      |      |    +----------+   +~~~~~~~+
      V      `--->|   AF21   |->-|RtrDstH|    Router Destination Host
  +----------+    +----------+   +~~~~~~~+
  |   AF21   |       Local DSCPs Provider T
  +----------+
      |
   +~~~~~~~+
   |RtrPrTE|                                Router Provider T Egress
   +~~~~~~~+
      |          Diffserv
  +----------+
  |   AF31   |
  +----------+
      |          Intercon
   +~~~~~~~+
   |RtrPrF |                                Router Provider F
   +~~~~~~~+
      |
  +----------+
  |   AF11   |   Provider F
  +----------+
                  Figure 1: Diffserv-Intercon Example

Geib & Black Informational [Page 12] RFC 8100 Diffserv-Intercon March 2017

 Providers only need to deploy mappings of internal DSCPs to/from
 Diffserv-Intercon DSCPs, so that they can exchange traffic using the
 desired PHBs.  In the example, provider O has decided that the
 properties of his internal class AF21 are best met by the Diffserv-
 Intercon Assured Elastic Treatment Aggregate, PHB AF31.  At the
 outgoing peering interface connecting provider O with provider T, the
 former's peering router re-marks AF21 traffic to AF31.  The domain
 internal PHB of provider T that meets the requirement of the
 Diffserv-Intercon Assured Elastic Treatment Aggregate is from the
 AF2x PHB group.  Hence, AF31 traffic received at the interconnection
 with provider T is re-marked to AF21 by the peering router of domain
 T, and domain T has chosen to use MPLS TC value 2 for this aggregate.
 At the penultimate MPLS node, the top MPLS label is removed and
 exposes the IP header marked by the DSCP that has been set at the
 network ingress.  The peering router connecting domain T with domain
 F classifies the packet by its domain-T-internal DSCP AF21.  As the
 packet leaves domain T on the interface to domain F, this causes the
 packet's DSCP to be re-marked to AF31.  The peering router of domain
 F classifies the packet for domain-F-internal PHB AF11, as this is
 the PHB with properties matching the Diffserv-Intercon Assured
 Elastic Treatment Aggregate.
 This example can be extended.  The figure shows provider W using CS2
 for traffic that corresponds to Diffserv-Intercon Assured Elastic
 Treatment Aggregate PHB AF31; that traffic is mapped to AF31 at the
 Diffserv-Intercon interconnection to provider T.  In addition,
 suppose that provider O supports a PHB marked by AF22, and this PHB
 is supposed to obtain Diffserv transport within provider T's domain.
 Then provider O will re-mark it with DSCP AF32 for interconnection to
 provider T.
 Finally, suppose that provider W supports CS3 for internal use only.
 Then no Diffserv-Intercon DSCP mapping needs to be configured at the
 peering router.  Traffic, sent by provider W to provider T marked by
 CS3 due to a misconfiguration may be re-marked to CS0 by provider T.

4.2. End-to-End PHB and DSCP Transparency

 This section briefly discusses end-to-end Diffserv approaches related
 to the Uniform, Pipe, and Short Pipe Model tunnels [RFC2983]
 [RFC3270] when used edge-to-edge in a network.
 o  With the Uniform Model, neither the DSCP nor the PHB change.  This
    implies that a network management packet received with a CS6 DSCP
    would be forwarded with an MPLS TC corresponding to CS6.  The
    Uniform Model is outside the scope of this document.

Geib & Black Informational [Page 13] RFC 8100 Diffserv-Intercon March 2017

 o  With the Pipe Model, the inner tunnel DSCP remains unchanged, but
    an outer tunnel DSCP and the PHB could change.  For example, a
    packet received with a (network-specific) CS1 DSCP would be
    transported by a Default PHB and, if MPLS is applicable, forwarded
    with an MPLS TC corresponding to the Default PHB.  The CS1 DSCP is
    not rewritten.  Transport of a large variety (much greater than
    four) DSCPs may be required across an interconnected network
    operating MPLS Short Pipe Model transport for IP traffic.  In that
    case, a tunnel based on the Pipe Model is among the possible
    approaches.  The Pipe Model is outside the scope of this document.
 o  With the Short Pipe Model, the DSCP likely changes, and the PHB
    might change.  This document describes a method to simplify
    Diffserv network interconnection when a DSCP rewrite can't be
    avoided.

4.3. Treatment of Network Control Traffic at Carrier Interconnection

    Interfaces
 As specified in Section 3.2 of RFC 4594, NC traffic marked by CS6 is
 expected at some interconnection interfaces.  This document does not
 change RFC 4594 but observes that network control traffic received at
 a network ingress is generally different from network control traffic
 within a network that is the primary use of CS6 envisioned by RFC
 4594.  A specific example is that some CS6 traffic exchanged across
 carrier interconnections is terminated at the network ingress node,
 e.g., when BGP is used between the two routers on opposite ends of an
 interconnection link; in this case, the operators would enter into a
 bilateral agreement to use CS6 for that BGP traffic.
 The end-to-end discussion in Section 4.2 is generally inapplicable to
 network control traffic -- network control traffic is generally
 intended to control a network, not be transported between networks.
 One exception is that network control traffic makes sense for a
 purchased transit agreement, and preservation of the CS6 DSCP marking
 for network control traffic that is transited is reasonable in some
 cases, although it is generally inappropriate to use CS6 for
 forwarding that traffic within the network that provides transit.
 Use of an IP tunnel is suggested in order to conceal the CS6 markings
 on transiting network control traffic from the network that provides
 the transit.  In this case, the Pipe Model for Diffserv tunneling is
 used.
 If the MPLS Short Pipe Model is deployed for unencapsulated IPv4
 traffic, an IP network provider should limit access to the CS6 and
 CS7 DSCPs, so that they are only used for network control traffic for
 the provider's own network.

Geib & Black Informational [Page 14] RFC 8100 Diffserv-Intercon March 2017

 Interconnecting carriers should specify treatment of CS6-marked
 traffic received at a carrier interconnection that is to be forwarded
 beyond the ingress node.  An SLA covering the following cases is
 recommended when a provider wishes to send CS6-marked traffic across
 an interconnection link and that traffic's destination is beyond the
 interconnected ingress node:
 o  classification of traffic that is network control traffic for both
    domains.  This traffic should be classified and marked for the CS6
    DSCP.
 o  classification of traffic that is network control traffic for the
    sending domain only.  This traffic should be forwarded with a PHB
    that is appropriate for transiting NC service class traffic
    [RFC4594] in the receiving domain, e.g., AF31 as specified by this
    document.  As an example, GSMA IR.34 recommends an Interactive
    class / AF31 to carry SIP and DIAMETER traffic.  While this is
    service control traffic of high importance to interconnected
    Mobile Network Operators, it is certainly not network control
    traffic for a fixed network providing transit among such operators
    and hence should not receive CS6 treatment in such a transit
    network.
 o  any other CS6-marked traffic should be re-marked or dropped.

5. IANA Considerations

 This document does not require any IANA actions.

6. Security Considerations

 The DSCP field in the IP header can expose additional traffic
 classification information at network interconnections by comparison
 to the use of a zero DSCP for all interconnect traffic.  If traffic
 classification information is sensitive, the DSCP field could be
 re-marked to zero to hide the classification as a countermeasure, at
 the cost of loss of Diffserv information and differentiated traffic
 handling on the interconnect and subsequent networks.  When AF PHBs
 are used, any such re-marking should respect AF PHB group boundaries
 as further discussed at the end of Section 4.
 This document does not introduce new features; it describes how to
 use existing ones.  The Diffserv security considerations in [RFC2475]
 and [RFC4594] apply.

Geib & Black Informational [Page 15] RFC 8100 Diffserv-Intercon March 2017

7. References

7.1. Normative References

 [RFC2474]  Nichols, K., Blake, S., Baker, F., and D. Black,
            "Definition of the Differentiated Services Field (DS
            Field) in the IPv4 and IPv6 Headers", RFC 2474,
            DOI 10.17487/RFC2474, December 1998,
            <http://www.rfc-editor.org/info/rfc2474>.
 [RFC2597]  Heinanen, J., Baker, F., Weiss, W., and J. Wroclawski,
            "Assured Forwarding PHB Group", RFC 2597,
            DOI 10.17487/RFC2597, June 1999,
            <http://www.rfc-editor.org/info/rfc2597>.
 [RFC3246]  Davie, B., Charny, A., Bennet, J., Benson, K., Le Boudec,
            J., Courtney, W., Davari, S., Firoiu, V., and D.
            Stiliadis, "An Expedited Forwarding PHB (Per-Hop
            Behavior)", RFC 3246, DOI 10.17487/RFC3246, March 2002,
            <http://www.rfc-editor.org/info/rfc3246>.
 [RFC3270]  Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen,
            P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi-
            Protocol Label Switching (MPLS) Support of Differentiated
            Services", RFC 3270, DOI 10.17487/RFC3270, May 2002,
            <http://www.rfc-editor.org/info/rfc3270>.
 [RFC5129]  Davie, B., Briscoe, B., and J. Tay, "Explicit Congestion
            Marking in MPLS", RFC 5129, DOI 10.17487/RFC5129, January
            2008, <http://www.rfc-editor.org/info/rfc5129>.
 [RFC5865]  Baker, F., Polk, J., and M. Dolly, "A Differentiated
            Services Code Point (DSCP) for Capacity-Admitted Traffic",
            RFC 5865, DOI 10.17487/RFC5865, May 2010,
            <http://www.rfc-editor.org/info/rfc5865>.

7.2. Informative References

 [BGP-INTERCONNECTION]
            Knoll, T., "BGP Class of Service Interconnection", Work in
            Progress, draft-knoll-idr-cos-interconnect-17, November
            2016.
 [IR.34]    GSMA, "Guidelines for IPX Provider networks (Previously
            Inter-Service Provider IP Backbone Guidelines)", Official
            Document IR.34, Version 11.0, November 2014,
            <http://www.gsma.com/newsroom/wp-content/uploads/
            IR.34-v11.0.pdf>.

Geib & Black Informational [Page 16] RFC 8100 Diffserv-Intercon March 2017

 [MEF23.1]  MEF, "Implementation Agreement MEF 23.1: Carrier Ethernet
            Class of Service - Phase 2", MEF 23.1, January 2012,
            <http://metroethernetforum.org/PDF_Documents/
            technical-specifications/MEF_23.1.pdf>.
 [RFC2475]  Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
            and W. Weiss, "An Architecture for Differentiated
            Services", RFC 2475, DOI 10.17487/RFC2475, December 1998,
            <http://www.rfc-editor.org/info/rfc2475>.
 [RFC2983]  Black, D., "Differentiated Services and Tunnels",
            RFC 2983, DOI 10.17487/RFC2983, October 2000,
            <http://www.rfc-editor.org/info/rfc2983>.
 [RFC3662]  Bless, R., Nichols, K., and K. Wehrle, "A Lower Effort
            Per-Domain Behavior (PDB) for Differentiated Services",
            RFC 3662, DOI 10.17487/RFC3662, December 2003,
            <http://www.rfc-editor.org/info/rfc3662>.
 [RFC4594]  Babiarz, J., Chan, K., and F. Baker, "Configuration
            Guidelines for DiffServ Service Classes", RFC 4594,
            DOI 10.17487/RFC4594, August 2006,
            <http://www.rfc-editor.org/info/rfc4594>.
 [RFC5127]  Chan, K., Babiarz, J., and F. Baker, "Aggregation of
            Diffserv Service Classes", RFC 5127, DOI 10.17487/RFC5127,
            February 2008, <http://www.rfc-editor.org/info/rfc5127>.
 [RFC5160]  Levis, P. and M. Boucadair, "Considerations of Provider-
            to-Provider Agreements for Internet-Scale Quality of
            Service (QoS)", RFC 5160, DOI 10.17487/RFC5160, March
            2008, <http://www.rfc-editor.org/info/rfc5160>.
 [RFC7657]  Black, D., Ed. and P. Jones, "Differentiated Services
            (Diffserv) and Real-Time Communication", RFC 7657,
            DOI 10.17487/RFC7657, November 2015,
            <http://www.rfc-editor.org/info/rfc7657>.
 [SLA-EXCHANGE]
            Shah, S., Patel, K., Bajaj, S., Tomotaki, L., and M.
            Boucadair, "Inter-domain SLA Exchange Attribute", Work in
            Progress, draft-ietf-idr-sla-exchange-10, January 2017.
 [Y.1566]   ITU-T, "Quality of service mapping and interconnection
            between Ethernet, Internet protocol and multiprotocol
            label switching networks", ITU-T Recommendation Y.1566,
            July 2012,
            <http://www.itu.int/rec/T-REC-Y.1566-201207-I/en>.

Geib & Black Informational [Page 17] RFC 8100 Diffserv-Intercon March 2017

Appendix A. The MPLS Short Pipe Model and IP Traffic

 The MPLS Short Pipe Model (or penultimate hop label popping) is
 widely deployed in carrier networks.  If unencapsulated IP traffic is
 transported using MPLS Short Pipe, IP headers appear inside the last
 section of the MPLS domain.  This impacts the number of PHBs and
 DSCPs that a network provider can reasonably support.  See Figure 2
 for an example.
 For encapsulated IP traffic, only the outer tunnel header is relevant
 for forwarding.  If the tunnel does not terminate within the MPLS
 network section, only the outer tunnel DSCP is involved, as the inner
 DSCP does not affect forwarding behavior; in this case, all DSCPs
 could be used in the inner IP header without affecting network
 behavior based on the outer MPLS header.  Here, the Pipe Model
 applies.
 Layer 2 and Layer 3 VPN traffic all use an additional MPLS label; in
 this case, the MPLS tunnel follows the Pipe Model.  Classification
 and queuing within an MPLS network is always based on an MPLS label,
 as opposed to the outer IP header.
 Carriers often select PHBs and DSCPs without regard to
 interconnection.  As a result, PHBs and DSCPs typically differ
 between network carriers.  With the exception of best-effort traffic,
 a DSCP change should be expected at an interconnection at least for
 unencapsulated IP traffic, even if the PHB is suitably mapped by the
 carriers involved.
 Although RFC 3270 suggests that the Short Pipe Model is only
 applicable to VPNs, current networks also use it to transport
 non-tunneled IPv4 traffic.  This is shown in Figure 2 where Diffserv-
 Intercon is not used, resulting in exposure of the internal DSCPs of
 the upstream network to the downstream network across the
 interconnection.

Geib & Black Informational [Page 18] RFC 8100 Diffserv-Intercon March 2017

     |
    \|/           IPv4, DSCP_send
     V
     |
Peering Router
     |
    \|/           IPv4, DSCP_send
     V
     |
MPLS Edge Router
     |          Mark MPLS Label, TC_internal
    \|/         Re-mark DSCP to
     V            (Inner: IPv4, DSCP_d)
     |
MPLS Core Router  (penultimate hop label popping)
     |                        \
     |            IPv4, DSCP_d |  The DSCP needs to be in network-
     |                 ^^^^^^^^|  internal Diffserv context.  The Core
    \|/                         > Router may require or enforce
     V                         |  that.  The Edge Router may wrongly
     |                         |  classify, if the DSCP is not in
     |                        /   network-internal Diffserv context.
MPLS Edge Router
     |                        \   Traffic leaves the network marked
    \|/           IPv4, DSCP_d |  with the network-internal
     V                          > DSCP_d that must be dealt with
     |                         |  by the next network (downstream).
     |                        /
Peer Router
     |          Re-mark DSCP to
    \|/           IPv4, DSCP_send
     V
     |
     Figure 2: Short Pipe Model / Penultimate Hop Popping Example
 The packet's IP DSCP must be in a well-understood Diffserv context
 for schedulers and classifiers on the interfaces of the ultimate MPLS
 link (last link traversed before leaving the network).  The necessary
 Diffserv context is network-internal, and a network operating in this
 mode enforces DSCP usage in order to obtain robust differentiated
 forwarding behavior.
 Without Diffserv-Intercon treatment, the traffic is likely to leave
 each network marked with network-internal DSCP.  DSCP_send in the
 figure above has to be re-marked into the first network's Diffserv
 scheme at the ingress MPLS Edge Router, to DSCP_d in the example.

Geib & Black Informational [Page 19] RFC 8100 Diffserv-Intercon March 2017

 For that reason, the traffic leaves this domain marked by the
 network-internal DSCP_d.  This structure requires that every carrier
 deploys per-peer PHB and DSCP mapping schemes.
 If Diffserv-Intercon is applied, DSCPs for traffic transiting the
 domain can be mapped from and remapped to an original DSCP.  This is
 shown in Figure 3.  Internal traffic may continue to use internal
 DSCPs (e.g., DSCP_d), and they may also be used between a carrier and
 its direct customers.
 Internal Router
      |
      |   Outer Header
     \|/    IPv4, DSCP_send
      V
      |
 Peering Router
      |  Re-mark DSCP to
     \|/    IPv4, DSCP_ds-int    Diffserv-Intercon DSCP and PHB
      V
      |
 MPLS Edge Router
      |
      |   Mark  MPLS Label, TC_internal
     \|/  Re-mark DSCP to
      V     (Inner: IPv4, DSCP_d)   Domain Internal DSCP for
      |                             the PHB
 MPLS Core Router  (penultimate hop label popping)
      |
      |     IPv4, DSCP_d
      |           ^^^^^^
     \|/
      V
      |
      |
 MPLS Edge Router--------------------+
      |                              |
     \|/  Re-mark DSCP to           \|/  IPv4, DSCP_d
      V     IPv4, DSCP_ds-int        V
      |                              |
      |                              |
 Peer Router              Domain Internal Broadband
      |                        Access Router
     \|/  Re-mark DSCP to           \|/
      V     IPv4, DSCP_send          V  IPv4, DSCP_d
      |                              |
       Figure 3: Short Pipe Model Example with Diffserv-Intercon

Geib & Black Informational [Page 20] RFC 8100 Diffserv-Intercon March 2017

Acknowledgements

 Bob Briscoe and Gorry Fairhurst reviewed this specification and
 provided rich feedback.  Brian Carpenter, Fred Baker, Al Morton, and
 Sebastien Jobert discussed the specification and helped improve it.
 Mohamed Boucadair and Thomas Knoll helped by adding awareness of
 related work.  James Polk's discussion during IETF 89 helped to
 improve the text on the relation of this specification to RFCs 4594
 and 5127.

Authors' Addresses

 Ruediger Geib (editor)
 Deutsche Telekom
 Heinrich Hertz Str. 3-7
 Darmstadt  64295
 Germany
 Phone: +49 6151 5812747
 Email: Ruediger.Geib@telekom.de
 David L. Black
 Dell EMC
 176 South Street
 Hopkinton, MA
 United States of America
 Phone: +1 (508) 293-7953
 Email: david.black@dell.com

Geib & Black Informational [Page 21]

/data/webs/external/dokuwiki/data/pages/rfc/rfc8100.txt · Last modified: 2017/03/10 01:58 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki