GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc7988

Internet Engineering Task Force (IETF) E. Rosen, Ed. Request for Comments: 7988 Juniper Networks, Inc. Updates: 6513, 6514 K. Subramanian Category: Standards Track Sproute Networks ISSN: 2070-1721 Z. Zhang

                                                Juniper Networks, Inc.
                                                          October 2016
            Ingress Replication Tunnels in Multicast VPN

Abstract

 RFCs 6513, 6514, and other RFCs describe procedures by which a
 Service Provider may offer Multicast VPN (MVPN) service to its
 customers.  These procedures create point-to-multipoint (P2MP) or
 multipoint-to-multipoint (MP2MP) trees across the Service Provider's
 backbone.  One type of P2MP tree that may be used is known as an
 "Ingress Replication (IR) tunnel".  In an IR tunnel, a parent node
 need not be directly connected to its child nodes.  When a parent
 node has to send a multicast data packet to its n child nodes, it
 does not use Layer 2 multicast, IP multicast, or MPLS multicast to do
 so.  Rather, it makes n individual copies, and then unicasts each
 copy, through an IP or MPLS unicast tunnel, to exactly one child
 node.  While the prior MVPN specifications allow the use of IR
 tunnels, those specifications are not always very clear or explicit
 about how the MVPN protocol elements and procedures are applied to IR
 tunnels.  This document updates RFCs 6513 and 6514 by adding
 additional details that are specific to the use of IR tunnels.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 7841.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc7988.

Rosen, et al. Standards Track [Page 1] RFC 7988 IR Tunnels in MVPN October 2016

Copyright Notice

 Copyright (c) 2016 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Table of Contents

 1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
 2.  What is an IR P-tunnel? . . . . . . . . . . . . . . . . . . .   5
 3.  How are IR P-tunnels identified?  . . . . . . . . . . . . . .   7
 4.  How to Join an IR P-Tunnel  . . . . . . . . . . . . . . . . .   9
   4.1.  Advertised IR P-Tunnels . . . . . . . . . . . . . . . . .   9
     4.1.1.  If the Leaf Information Required Bit Is Set . . . . .  10
     4.1.2.  If the Leaf Information Required Bit Is Not Set . . .  10
   4.2.  Unadvertised IR P-Tunnels . . . . . . . . . . . . . . . .  11
 5.  The PTA's Tunnel Identifier Field . . . . . . . . . . . . . .  11
 6.  A Note on IR P-Tunnels and Discarding Packets from the Wrong
     PE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
 7.  The PTA's MPLS Label Field  . . . . . . . . . . . . . . . . .  14
   7.1.  Leaf A-D Route Originated by an Egress PE . . . . . . . .  14
   7.2.  Leaf A-D Route Originated by an Intermediate Node . . . .  16
   7.3.  Intra-AS I-PMSI A-D Route . . . . . . . . . . . . . . . .  17
 8.  How A Child Node Prunes Itself from an IR P-Tunnel  . . . . .  17
 9.  Parent Node Actions upon Receiving Leaf A-D Route . . . . . .  18
 10. Use of Timers When Switching UMH  . . . . . . . . . . . . . .  19
 11. Security Considerations . . . . . . . . . . . . . . . . . . .  20
 12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  21
    12.1. Normative References . . . . . . . . . . . . . . . . . .  21
    12.2. Informative References . . . . . . . . . . . . . . . . .  21
 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  23
 Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  23

Rosen, et al. Standards Track [Page 2] RFC 7988 IR Tunnels in MVPN October 2016

1. Introduction

 RFCs 6513, 6514, and other RFCs describe procedures by which a
 Service Provider (SP) may offer Multicast VPN (MVPN) service to its
 customers.  These procedures create point-to-multipoint (P2MP) or
 multipoint-to-multipoint (MP2MP) tunnels, called "P-tunnels"
 (provider tunnels), across the SP's backbone network.  Customer
 multicast traffic is carried through the P-tunnels.
 A number of different P-tunnel technologies are supported.  One of
 the supported P-tunnel technologies is known as "ingress replication"
 or "unicast replication".  We will use the acronym "IR" to refer to
 this P-tunnel technology.
 An IR P-tunnel is a P2MP tree, but a given node on the tree is not
 necessarily directly attached to its parent node or to its child
 nodes.  To send a multicast data packet from a parent node to one of
 its child nodes, the parent node encapsulates the packet and then
 unicasts it through a tunnel to the child node.  The tunnel may be a
 P2P or MP2P MPLS LSP (Label Switched Path) or a unicast IP tunnel.
 If a node on an IR tree has n child nodes, and has a multicast data
 packet that must be sent along the tree, the parent node makes n
 individual copies of the data packet, and then sends each copy,
 through a unicast tunnel, to exactly one child node.  No lower-layer
 multicast technology is used when sending traffic from a parent node
 to a child node; therefore, multiple copies of the packet may be sent
 out a single interface.
 With the single exception of IR, the P-tunnel technologies supported
 by the MVPN specifications are preexisting IP multicast or MPLS
 multicast technologies.  Each such technology has its own set of
 specifications, its own setup and maintenance protocols, its own
 syntax for identifying specific multicast trees, and its own
 procedures for enabling a router to be added to or removed from a
 particular multicast tree.  For IR P-tunnels, on the other hand,
 there is no prior specification for setting up and maintaining the
 P2MP trees; the procedures and protocol elements used for setting up
 and maintaining the P2MP trees are specified in the MVPN
 specifications themselves, and all the signaling/setup is done by
 using the BGP Auto-Discovery (A-D) routes that are defined in
 [RFC6514].  (The unicast tunnels used to transmit multicast data from
 one node to another in an IR P-tunnel may of course have their own
 setup and maintenance protocols, e.g., [RFC5036], [RFC3209].)
 Since the transmission of a multicast data packet along an IR
 P-tunnel is done by transmitting the packet through a unicast tunnel,
 previous RFCs sometimes describe an IR P-tunnel as "consisting of" a
 set of unicast tunnels.  However, that description is not quite

Rosen, et al. Standards Track [Page 3] RFC 7988 IR Tunnels in MVPN October 2016

 accurate.  For one thing, it obscures the fact that an IR P-tunnel is
 really a P2MP tree, whose nodes must maintain multicast state in both
 the control and data planes.  For another, it obscures the fact the
 unicast tunnels used by a particular IR P-tunnel need not be specific
 to that P-tunnel; a single unicast tunnel can carry the multicast
 traffic of many different IR P-tunnels (and can also carry unicast
 traffic as well).
 In this document, we provide a clearer and more explicit conceptual
 model for IR P-tunnels, clarifying the relationship between an IR
 P-tunnel and the unicast tunnels that are used for data transmission
 along the IR P-tunnel.
 Section 5 of [RFC6514] defines a BGP Path Attribute known as the
 "PMSI (Provider Multicast Service Interface) Tunnel attribute" (PTA).
 This attribute contains a field known as the "Tunnel Identifier"
 field.  For most P-tunnel technologies, the PTA's "Tunnel Identifier"
 field is used to identify a P-tunnel (i.e., to identify a P2MP or
 MP2MP tree).  However, when IR P-tunnels are used, the PTA "Tunnel
 Identifier" field does not actually identify an IR P-tunnel.  In some
 cases, it identifies one of the P-tunnel's constituent unicast
 tunnels; in other cases, it is not used to identify a tunnel at all.
 In this document, we provide an explicit specification for how IR
 P-tunnels are actually identified.
 Some of the MVPN specifications specify procedures that require a PE
 router to join the P-tunnel that has been identified in a particular
 MVPN route.  However, up to now, there has not been an explicit
 specification of how to identify an IR P-tunnel, of how a router
 joins such a P-tunnel, or of how a router prunes itself from such a
 P-tunnel.  In this document, we make these procedures more explicit.
 [RFC6514] does provide a method for binding an MPLS label to a
 P-tunnel, but does not discuss the label allocation policies that are
 needed for correct operation when the P-tunnel is an IR P-tunnel.
 Those policies are discussed in this document.
 This document does not provide any new protocol elements or any
 fundamentally new procedures; its purpose is to make explicit just
 how a router is to use the protocol elements and procedures of
 [RFC6513] and [RFC6514] to identify an IR P-tunnel, to join an IR
 P-tunnel, and to prune itself from an IR P-tunnel.
 This document also discusses the MPLS label allocation policies that
 need to be supported when binding MPLS labels to IR P-tunnels, and
 the timer policies that need to be supported when switching a
 customer multicast flow from one IR P-tunnel to another.  These are
 procedures that are not clearly specified in [RFC6513] or [RFC6514].

Rosen, et al. Standards Track [Page 4] RFC 7988 IR Tunnels in MVPN October 2016

 As the material in this document must be understood in order to
 properly implement IR P-tunnels, this document updates [RFC6513] and
 [RFC6514].
 This document also discusses the application of "seamless multicast"
 [RFC7524] and "extranet" [RFC7900] procedures to IR P-tunnels.
 This document does not discuss the use of IR P-tunnels to support a
 VPN customer's use of Bidirectional Protocol Independent Multicast
 (BIDIR-PIM).  [RFC7740] explains how to adapt the procedures of
 [RFC6513], [RFC6514], and [RFC7582] so that a customer's use of
 BIDIR-PIM can be supported by IR P-tunnels.
 In the event of any conflict between this document and either
 [RFC6513] or [RFC6514], this document takes precedence.
 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
 "OPTIONAL", when and only when appearing in all capital letters, are
 to be interpreted as described in [RFC2119].

2. What is an IR P-tunnel?

 An IR P-tunnel is a P2MP tree.  Its nodes are BGP speakers that
 support the MVPN procedures of [RFC6514] and related RFCs.  In
 general, the nodes of an IR P-tunnel are either Provider Edge (PE)
 routers, Autonomous System Border Routers (ASBRs), or (if [RFC7524]
 is supported) Area Border Routers (ABRs).  (MVPN procedures are
 sometimes used to support non-MVPN, or "global table" multicast; one
 way of doing this is defined in [RFC7524].  Another way is defined in
 [RFC7716].  In such cases, IR P-tunnels can be used outside the
 context of MVPN.)
 MVPN P-tunnels may be either "segmented" or "non-segmented" (as these
 terms are defined in [RFC6513] and [RFC6514]).
 A "non-segmented" IR P-tunnel is a two-level P2MP tree, consisting
 only of a root node and a set of nodes that are children of the root
 node.  When used in an MVPN context, the root is an ingress PE, and
 the child nodes of the root are the egress PEs.
 In a segmented P-tunnel, IR may be used for some or all of the
 segments.  If a particular segment of a segmented P-tunnel uses IR,
 then the root of that segment may have child nodes that are ABRs or
 ASBRs, rather than egress PEs.

Rosen, et al. Standards Track [Page 5] RFC 7988 IR Tunnels in MVPN October 2016

 As with any type of P2MP tree, each node of an IR P-tunnel holds
 "multicast state" for the P-tunnel.  That is, each node knows the
 identity of its parent node on the tree, and each node knows the
 identities of its child nodes on the tree.  In the MVPN specs, the
 "parent" node is also known as the "Upstream Multicast Hop" or "UMH".
 Note that the UMH may be a PE, an ASBR, or (if procedures from
 [RFC7524] are being used) an ABR.  (In [RFC7524], the term "upstream
 node" is used instead of "UMH".)
 What distinguishes an IR P-tunnel from any other kind of P2MP tree is
 the method by which a data packet is transmitted from a parent node
 to a child node.  To transmit a multicast data packet from a parent
 node to a child node along a particular IR P-tunnel, the parent node
 does the following:
 o  It labels the packet with a label (call it a "P-tunnel label")
    that the child node has assigned to that P-tunnel.
 o  It then places the packet in a unicast encapsulation and unicasts
    the packet to the child node.  That is, the parent node sends the
    packet through a unicast tunnel to a particular child node.  This
    unicast tunnel need not be specially created to be part of the IR
    P-tunnel; it can be any P2P or MP2P unicast tunnel that will get
    the packets from the parent node to the child node.  A single such
    unicast tunnel may be carrying multicast data packets of several
    different P2MP trees and may also be carrying unicast data
    packets.
 The parent node repeats this process for each child node, creating
 one copy for each child node, and sending each copy through a unicast
 tunnel to corresponding child node.  It does not use Layer 2
 multicast, IP multicast, or MPLS multicast to transmit packets to its
 child nodes.  As a result, multiple copies of each packet may be sent
 out a single interface; this may happen, e.g., if that interface is
 the next-hop interface, according to unicast routing, from the parent
 node to several of the child nodes.
 Since data traveling along an IR P-tunnel is always unicast from
 parent node to child node, it can be convenient to think of an IR
 P-tunnel as a P2MP tree whose arcs are unicast tunnels.  However, it
 is important to understand that the unicast tunnels need not be
 specific to any particular IR P-tunnel.  If R1 is the parent node of
 R2 on two different IR P-tunnels, a single unicast tunnel from R1 to
 R2 may be used to carry data along both IR P-tunnels.  All that is
 required is that when the data packets arrive at R2, R2 will see the
 "P-tunnel label" at the top of the packets' label stack; R2's further

Rosen, et al. Standards Track [Page 6] RFC 7988 IR Tunnels in MVPN October 2016

 processing of the packets will depend upon that label.  Note that the
 same unicast tunnel between R1 and R2 may also be carrying unicast
 data packets.
 Typically, the unicast tunnels are the LSPs that already exist to
 carry unicast traffic; either MP2P LSPs created by the Label
 Distribution Protocol (LDP) [RFC5036] or P2P LSPs created by Resource
 Reservation Protocol - Traffic Engineering (RSVP-TE) [RFC3209].
 However, any other kind of unicast tunnel may be used.  A unicast
 tunnel may have an arbitrary number of intermediate routers; those
 routers do not maintain any multicast state for the IR P-tunnel and,
 in general, are not even aware of its existence.
 As with all other P-tunnel types, an IR P-tunnel may be used to
 instantiate either an Inclusive PMSI (I-PMSI) or a Selective PMSI
 (S-PMSI).  See Section 3.2 of [RFC6513] for an explanation of those
 concepts.

3. How are IR P-tunnels identified?

 There are four MVPN BGP route types in which P-tunnels can be
 identified: Intra-AS I-PMSI A-D routes, Inter-AS I-PMSI A-D routes,
 S-PMSI A-D routes, and Leaf A-D routes.  (These route types are all
 defined in [RFC6514]).
 Whenever it is necessary to identify a P-tunnel in a route of one of
 these types, a "PMSI Tunnel Attribute" (PTA) is added to the route.
 As defined in Section 5 of [RFC6514], the PTA contains four fields:
 Tunnel Type, MPLS Label, Tunnel Identifier, and Flags.  [RFC6514]
 defines only one bit in the Flags field, the Leaf Information
 Required bit.
 If a route identifies an IR P-tunnel, the Tunnel Type field of its
 PTA is set to the value 6, meaning "Ingress Replication".
 Most types of P-tunnel are associated with specific protocols that
 are used to set up and maintain tunnels of that type.  For example,
 if the Tunnel Type field is set to 2, meaning "mLDP P2MP LSP", the
 associated setup protocol is Multipoint LDP (mLDP) [RFC6388].  The
 associated setup protocol always has a method of identifying the
 tunnels that it sets up.  For example, mLDP uses an FEC element
 (Forwarding Equivalence Class element) to identify a tree.  If the
 Tunnel Type field is set to 3, meaning "PIM-SSM Tree", where "SSM"
 stands for Source-Specific Multicast, the associated setup protocol
 is PIM, and "(S,G)" is used to identify the tree.  In these cases,
 the Tunnel Identifier field of the PTA carries a tree identifier as
 defined by the setup protocol used for the particular tunnel type.

Rosen, et al. Standards Track [Page 7] RFC 7988 IR Tunnels in MVPN October 2016

 IR P-tunnels, on the other hand, are entirely setup and maintained by
 the use of BGP A-D routes and are not associated with any other setup
 protocol.  (The unicast tunnels used to transmit multicast data along
 an IR P-tunnel may have their own setup and maintenance protocols, of
 course.)  The means of identifying a P-tunnel is very different for
 IR P-tunnels than for other types of P-tunnel:
    When an IR P-tunnel is identified in an S-PMSI A-D route, an
    Intra-AS I-PMSI A-D route, or an Inter-AS I-PMSI A-D route (we
    will refer to these three route types as "advertising A-D
    routes"), its identifier is hereby defined to be the NLRI (Network
    Layer Reachability Information) of that route.  See Sections 4.1,
    4.2, and 4.3 of [RFC6514] for the specification of these NLRIs.
    Note that the IR P-tunnel identifier includes the Route Type and
    Length fields (see Section 4 of [RFC6514]) of the NLRI.
 To reiterate:
    The identifier of the IR P-tunnel does not appear in the PTA at
    all; the Tunnel Identifier field of the PTA does not contain the
    identifier of the IR P-tunnel.
    Rather, the identifier of the IR P-tunnel appears in the Network
    Layer Reachability Information (NLRI) field of the A-D routes that
    are used to advertise and to setup the IR P-tunnel.
 Note that an advertising A-D route is considered to identify an IR
 P-tunnel only if it carries a PTA whose Tunnel Type field is set to
 "IR".
 When an IR P-tunnel is identified in an S-PMSI A-D route or in an
 Inter-AS I-PMSI A-D route, the Leaf Information Required bit of the
 Flags field of the PTA MUST be set.
 In an advertising A-D route:
 o  If the Leaf Information Required bit of the Flags field of the PTA
    is set, then the Tunnel Identifier field of the PTA has no
    significance whatsoever and MUST be ignored upon reception.
    Note that, per RFC 6514, the length of the Tunnel Identifier field
    of the PTA is variable and is inferred from the length of the PTA.
    Even when this field is of no significance, its length MUST be the
    length of an IP address in the address space of the SP's backbone,
    as specified in Section 4.2 of [RFC6515].  In this case, it is
    RECOMMENDED that it be set to a routable address of the router
    that constructed the PTA.  (While it might make more sense to

Rosen, et al. Standards Track [Page 8] RFC 7988 IR Tunnels in MVPN October 2016

    allow or even require the field to be omitted entirely, that might
    raise issues of backwards compatibility with implementations that
    were designed prior to the publication of this document.)
 o  If the Leaf Information Required bit is not set, the Tunnel
    Identifier field of the PTA does have significance, but it does
    not identify the IR P-tunnel.  The use of the PTA's Tunnel
    Identifier field in this case is discussed in Section 5 of this
    document.
 Note that according to the above definition, there is no way for two
 different advertising A-D routes (i.e., two advertising A-D routes
 with different NLRIs) to advertise the same IR P-tunnel.  In the
 terminology of [RFC6513], an IR P-tunnel can instantiate only a
 single PMSI.  If an ingress PE, for example, wants to bind two
 customer multicast flows to a single IR P-tunnel, it must advertise
 that IR P-tunnel either in an I-PMSI A-D route or in an S-PMSI A-D
 route whose NLRI contains wildcards [RFC6625].
 When an IR P-tunnel is identified in a Leaf A-D route, its identifier
 is the Route Key field of the route's NLRI.  See Section 4.4 of
 [RFC6514].
 A Leaf A-D route is considered to identify an IR P-tunnel only if it
 carries a PTA whose Tunnel Type field is set to "IR".  In this type
 of route, the Tunnel Identifier field of the PTA does have
 significance, but it does not identify the IR P-tunnel.  The use of
 the PTA's Tunnel Identifier field in this case is discussed in
 Section 5.

4. How to Join an IR P-Tunnel

 The procedures for joining an IR P-tunnel depend upon whether the
 P-tunnel has been previously advertised, and, if so, upon how the
 P-tunnel was advertised.  Note that joining an unadvertised IR
 P-tunnel is only possible when using the "global table multicast"
 procedures of [RFC7524].

4.1. Advertised IR P-tunnels

 The procedures in this section apply when the IR P-tunnel to be
 joined has been advertised in an S-PMSI A-D route, an Inter-AS I-PMSI
 A-D route, or an Intra-AS I-PMSI A-D route.
 The procedures for joining an advertised IR P-tunnel depend upon
 whether the A-D route that advertises the IR P-tunnel has the Leaf
 Information Required bit set in its PTA.

Rosen, et al. Standards Track [Page 9] RFC 7988 IR Tunnels in MVPN October 2016

4.1.1. If the Leaf Information Required Bit Is Set

 The procedures in this section apply when the P-tunnel to be joined
 has been advertised in a route whose PTA has the Leaf Information
 Required bit set.
 The router joining a particular IR P-tunnel must determine its UMH
 for that P-tunnel.  If the route that advertised the IR P-tunnel
 contains a P2MP Segmented Next Hop Extended Community, the UMH is
 determined from the value of this community (see [RFC7524]).
 Otherwise, the UMH is determined from the route's next hop (see
 [RFC6514]).
 Once the UMH is determined, the router joining the IR P-tunnel
 originates a Leaf A-D route.  The NLRI of the Leaf A-D route is
 formed following the procedures of [RFC6514].  As a result, the NLRI
 of the Leaf A-D route will contain the IR P-tunnel identifier defined
 in Section 3 above as its "route key".  The UMH MUST be identified by
 attaching an "IP-address-specific Route Target" (or an "IPv6-address-
 specific Route Target") to the Leaf A-D route.  The IP address of the
 UMH appears in the Global Administrator field of the Route Target
 (RT).  Details can be found in [RFC6514] and [RFC7524].
 The Leaf A-D route MUST also contain a PTA whose fields are set as
 follows:
 o  The Tunnel Type field is set to "IR".
 o  The Tunnel Identifier field is set as described in Section 5 of
    this document.  (Note that this field does not contain the IR
    P-tunnel Identifier that is defined in Section 3.)
 o  The MPLS Label field is set to a non-zero value.  This is the
    "P-tunnel label".  The value must be chosen so as to satisfy
    various constraints, as discussed in Section 7 this document.

4.1.2. If the Leaf Information Required Bit Is Not Set

 The procedures in this section apply when the IR P-tunnel to be
 joined has been advertised in a route whose PTA does not have the
 Leaf Information Required bit set.  This can only be the case if the
 IR P-tunnel was advertised in an Intra-AS I-PMSI A-D route.
 If an IR P-tunnel is advertised in the Intra-AS I-PMSI A-D routes
 originated by the PE routers of a given MVPN, the Intra-AS I-PMSI can
 be thought of as being instantiated by a set of IR P-tunnels.  Each
 PE is the root of one such IR P-tunnel, and the other PEs are

Rosen, et al. Standards Track [Page 10] RFC 7988 IR Tunnels in MVPN October 2016

 children of the root.  A PE simultaneously joins all these P-tunnels
 by originating (if it hasn't already done so) an Intra-AS I-PMSI A-D
 route with a PTA whose fields are set as follows:
 o  The Tunnel Type field is set to "IR".
 o  The Tunnel Identifier field is set as described in Section 5 of
    this document.  (Note that this field does not contain the IR
    P-tunnel identifier that is defined in Section 3.)
 o  The MPLS Label field MUST be set to a non-zero value.  This label
    value will be used by the child node to associate a received
    packet with the I-PMSI of a particular MVPN.  The MPLS label
    allocation policy must be such as to ensure that the binding from
    label to I-PMSI is one to one.
 The NLRI and the RTs of the originated I-PMSI A-D route are set as
 specified in [RFC6514].

4.2. Unadvertised IR P-Tunnels

 In [RFC7524], a procedure is defined for "global table multicast", in
 which a P-tunnel can be joined even if the P-tunnel has not been
 previously advertised.  See Sections 6.2.2 and 6.2.3 of [RFC7524]:
 "Leaf A-D Route for Global Table Multicast" and "Constructing the
 Rest of the Leaf A-D Route".  The route key of the Leaf A-D route has
 the form of the "S-PMSI Route-Type Specific NLRI" (see Section 4.3 of
 [RFC6514]) in this case, and that should be considered to be the IR
 P-tunnel identifier.  Note that the procedure for finding the UMH is
 different in this case; the UMH is the next hop of the best UMH-
 eligible route towards the "ingress PE".  See Section 6.1 of
 [RFC7524], entitled "Determining the Upstream ABR/PE/ASBR (Upstream
 Node)".

5. The PTA's Tunnel Identifier Field

 As discussed in Section 1, when the Tunnel Type field of a PTA is set
 to "IR", the Tunnel Identifier field of that PTA does not contain the
 IR P-tunnel identifier.  This section specifies the procedures for
 setting the Tunnel Identifier field of the PTA when the Tunnel Type
 field of the PTA is set to "IR".

Rosen, et al. Standards Track [Page 11] RFC 7988 IR Tunnels in MVPN October 2016

 If the Tunnel Type field of a PTA is set to "IR", its Tunnel
 Identifier field is significant only when one of the following two
 conditions holds:
 o  The PTA is carried by a Leaf A-D route, or
 o  The Leaf Information Required bit of the Flags field of the PTA is
    not set.
 If one of these conditions holds, then the Tunnel Identifier field
 must contain a routable IP address of the originator of the route.
 (See Sections 9.2.3.2.1 and 9.2.3.4.1 of [RFC6514] for the detailed
 specification of the contents of this field.)  This address is used
 by the UMH to determine the unicast tunnel that it will use in order
 to send data, along the IR P-tunnel identified by the route key, to
 the originator of the Leaf A-D route.
 The means by which the unicast tunnel is determined from this IP
 address is outside the scope of this document.  The means by which
 the unicast tunnel is set up and maintained is also outside the scope
 of this document.
 Section 4 of [RFC6515] MUST be applied when a PTA is carried in a
 Leaf A-D route.  It describes how to determine whether the Tunnel
 Identifier field carries an IPv4 or an IPv6 address.
 If neither of the above conditions hold, then the Tunnel Identifier
 field is of no significance and MUST be ignored upon reception.

6. A Note on IR P-Tunnels and Discarding Packets from the Wrong PE

 Section 9.1.1 of [RFC6513] specifies a procedure known as "Discarding
 Packets from the Wrong PE".  When an egress PE receives a multicast
 data packet, this procedure requires it to determine the packet's
 ingress PE.
 In this document, we assume that when a packet has reached an egress
 PE via an IR P-tunnel, the egress PE will infer the identity of the
 packet's ingress PE by examining the packet's P-tunnel label.
 Section 7 specifies certain constraints on the way in which the
 P-tunnel label is allocated for a given P-tunnel.  In general, if
 these constraints are followed, an egress PE will be able to infer
 the identity of a packet's ingress PE from the P-tunnel label, and
 hence will be able to apply the procedures of Section 9.1.1 of
 [RFC6513].  This method of identifying a packet's ingress PE works
 exactly the same when the unicast tunnels are IP tunnels as it does
 when the unicast tunnels are MPLS LSPs.

Rosen, et al. Standards Track [Page 12] RFC 7988 IR Tunnels in MVPN October 2016

 However, if the egress PE joined a particular IR P-tunnel using the
 procedures of Section 4.1.2, then when the egress PE receives a
 packet through that P-tunnel, it will not be able to infer the
 identity of the packet's ingress PE from the P-tunnel label, and thus
 will not be able to apply the procedures of Section 9.1.1 of
 [RFC6513].
 One might think that if a particular IR P-tunnel uses IP unicast
 tunnels rather than MPLS LSPs, an egress PE could identify the
 ingress PE by inspecting the IP source address field of the
 encapsulating IP header.  However, there are several reasons why this
 procedure is not desirable:
 o  When segmented P-tunnels are being used, the IP source address
    field of the encapsulating IP header might not contain the address
    of the ingress PE.
 o  Even if the IP source address field of the encapsulating IP header
    does identify the ingress PE, there is no guarantee that the IP
    source address in that header is the same as the IP address used
    by the ingress PE for the MVPN signaling procedures.
 o  To apply the procedures of Section 9.1.1 of [RFC6513] when
    extranet functionality [RFC7900] is supported, it is necessary to
    infer a packet's ingress VRF (Virtual Routing and Forwarding
    table), not merely its ingress PE.  This can be inferred from the
    P-tunnel label (assuming that the label is allocated following the
    procedures of Section 7), but it cannot be inferred from the IP
    source address of the encapsulating IP header.
 We therefore assume in this document that if the procedures of
 Section 9.1.1 of [RFC6513] are to be applied to packets traveling
 through IR P-tunnels, those procedures will be based on the P-tunnel
 label, even if the IR P-tunnel is using IP unicast tunnels.
 This means that if an egress PE joined a particular IR P-tunnel using
 the procedures of Section 4.1.2, duplicate prevention on that IR
 P-tunnel requires the use of either Single Forwarder Selection
 (Section 9.1.2 of [RFC6513]) or native PIM procedures (Section 9.1.3
 of [RFC6513]).

Rosen, et al. Standards Track [Page 13] RFC 7988 IR Tunnels in MVPN October 2016

7. The PTA's MPLS Label Field

 When the Tunnel Type field of a PTA is set to "IR", the MPLS Label
 field is not always significant.  It is significant only under the
 following conditions:
 1.  Either the PTA is being carried in a Leaf A-D route, or
 2.  the Leaf Information Required flag of the PTA is NOT set.
 Note that the Leaf Information Required flag of the PTA is always set
 when a PTA specifying an IR P-tunnel is carried in an S-PMSI A-D
 route or in an Inter-AS I-PMSI A-D route; thus, the MPLS Label field
 of the PTA is never significant when the PTA is carried by one of
 these route types.  The MPLS Label field is significant only when the
 PTA appears either in a Leaf A-D route or in an Intra-AS I-PMSI A-D
 route that does not have the Leaf Information Required bit set.  In
 these cases, the MPLS label is the label that the originator of the
 route is assigning to the IR P-tunnel(s) identified by the route's
 NLRI.  (That is, the MPLS label assigned in the PTA is what we have
 called the "P-tunnel label".)
 In those cases where the MPLS Label field is not significant, it
 SHOULD be set to zero upon transmission and MUST be ignored upon
 reception.

7.1. Leaf A-D Route Originated by an Egress PE

 As previously stated, when a Leaf A-D route is used to join an IR
 P-tunnel, the "route key" of the Leaf A-D route is the P-tunnel
 identifier.
 We now define the notion of the "root of an IR P-tunnel".
 o  If the identifier of an IR P-tunnel is of the form of an S-PMSI
    NLRI, the "root" of the IR P-tunnel is the router identified in
    the Originating Router's IP Address field of that NLRI.
 o  If the identifier of an IR P-tunnel is of the form specified in
    Section 6.2.2 of [RFC7524] ("Leaf A-D Route for Global Table
    Multicast"), the "root" of the IR P-tunnel is the router
    identified in the Ingress PE's IP Address field of that NLRI.
 o  If the identifier of an IR P-tunnel is of the form of an Intra-AS
    I-PMSI NLRI, the "root" of the IR P-tunnel is the router
    identified in the Originating Router's IP Address field of that
    NLRI.

Rosen, et al. Standards Track [Page 14] RFC 7988 IR Tunnels in MVPN October 2016

 o  If the identifier of an IR P-tunnel is of the form of an Inter-AS
    I-PMSI NLRI, the "root" of the IR P-tunnel is same as the
    identifier of the IR P-tunnel, i.e., the combination of a Route
    Distinguisher (RD) and an AS.
 Note that if an IR P-tunnel is segmented, the root of the IR
 P-tunnel, by this definition, is actually the root of the entire
 P-tunnel, not the root of the local segment.  In this case, there may
 be segments upstream that are not IR P-tunnels themselves.  However,
 the egress PE is aware only of the final segment of the P-tunnel, and
 hence considers the P-tunnel to be an IR P-tunnel.
 In order to apply the procedures of Section 9.1.1 of RFC 6513
 ("Discarding Packets from Wrong PE"), the following condition MUST be
 met by the MPLS label allocation policy:
    Suppose an egress PE originates two Leaf A-D routes, each with a
    different route key in its NLRI, and each with a PTA specifying a
    Tunnel Type field of "IR".  Thus, each of the Leaf A-D routes
    identifies a different IR P-tunnel.  Suppose further that each of
    those IR P-tunnels has a different root.  Then, the egress PE MUST
    NOT specify the same MPLS label in both PMSI Tunnel attributes.
 That is, to apply the duplicate prevention procedures (in "Discarding
 Packets from Wrong PE", Section 9.1.1 of [RFC6513]), the same MPLS
 label MUST NOT be assigned to two IR P-tunnels that have different
 roots.
 If segmented P-tunnels are in use, the above rule is necessary but
 not sufficient to prevent a PE from forwarding duplicate data to the
 CEs.  For various reasons, a given egress PE or egress ABR or egress
 ASBR may decide to change its parent node, on a given segmented
 P-tunnel, from one router to another.  It does this by changing the
 RT of the Leaf A-D route that it originated in order to join that
 P-tunnel.  Once the RT is changed, there may be a period of time
 during which the old parent node and the new parent node are both
 sending data of the same multicast flow.  To ensure that the egress
 node not forward duplicate data, whenever the egress node changes the
 RT that it attaches to a Leaf A-D route, it MUST also change the
 "MPLS Label" specified in the Leaf A-D route's PTA.  This allows the
 egress router to distinguish between packets arriving on a given
 P-tunnel from the old parent and packets arriving on that same
 P-tunnel from the new parent.  At any given time, a router MUST
 consider itself to have only a single parent node on a given P-tunnel
 and MUST discard traffic that arrives on that P-tunnel from a
 different parent node.

Rosen, et al. Standards Track [Page 15] RFC 7988 IR Tunnels in MVPN October 2016

 If extranet functionality [RFC7900] is not implemented in a
 particular egress PE, or if an egress PE is provisioned with the
 knowledge that extranet functionality is not needed, the PE may adopt
 the policy of assigning a label that is unique for the ordered triple
 <root, parent node, egress VRF>.  This will enable the egress PE to
 apply the duplicate prevention procedures discussed above and to
 determine the VRF to which an arriving packet must be directed.
 However, this policy is not sufficient to support the "Do Not Deliver
 Packets from the Wrong P-tunnel" procedures that are specified in
 Section 2.3.1 of [RFC7900].  To support those procedures, the labels
 specified in the PTA of Leaf A-D routes originated by a given egress
 PE MUST be unique for the ordered triple <root, root RD, parent
 node>, where the "root RD" is taken from the RD field of the IR
 P-tunnel identifier.  (All forms of IR P-tunnel identifier contain an
 embedded RD field.)  This policy is also sufficient for supporting
 non-extranet cases, but, in some cases, may result in the use of more
 labels than the policy of the preceding paragraph.

7.2. Leaf A-D Route Originated by an Intermediate Node

 When a P-tunnel is segmented, there will be "intermediate nodes",
 i.e., nodes that have a parent and also have children on the
 P-tunnel.  Each intermediate node is a leaf node of an "upstream
 segment" and a root node of one or more "downstream segments".  The
 intermediate node needs to set up its forwarding state so that data
 it receives on the upstream segment gets transmitted on the proper
 downstream segments.
 If the upstream segment is instantiated by IR, the intermediate node
 will need to originate a Leaf A-D route to join that segment, and
 will need to allocate a downstream-assigned MPLS label to advertise
 in the MPLS Label field of the Leaf A-D route's PTA.  Section 7.1
 specifies constraints on the label allocation policy for egress PEs;
 this section specifies constraints on the label allocation policy for
 intermediate nodes.
 Suppose intermediate node N originates two Leaf A-D routes, one whose
 route key is K1, and one whose route key is K2, where K1 != K2.  The
 respective PTAs of these Leaf A-D routes MUST specify distinct non-
 zero MPLS labels, UNLESS the following conditions all hold:
 1.  N's parent node for P-tunnel K1 is the same as N's parent node
     for P-tunnel K2.
 2.  N's forwarding state is such that any packet it receives from
     P-tunnel K1 is forwarded to the exact same set of downstream
     neighbors as any packet it receives from P-tunnel K2.

Rosen, et al. Standards Track [Page 16] RFC 7988 IR Tunnels in MVPN October 2016

 3.  For each downstream neighbor D to which N sends the packets it
     receives from P-tunnels K1 and K2, N's forwarding state is such
     that it applies the exact same encapsulation to packets it
     forwards from either tunnel to D.  (For example, if N uses MPLS
     to forward the packets to D, it pushes the exact same set of
     labels on packets from P-tunnel K1 as it pushes on packets from
     P-tunnel K2.)
 Of course, N MAY always specify distinct non-zero labels in each of
 the Leaf A-D routes that it originates.
 Note that the rules of this section apply whenever the upstream
 P-tunnel segment is an IR P-tunnel.  These rules hold whether or not
 some or all of the downstream segments are other types of P-tunnels.
 If the P-tunnels from N to a particular downstream neighbor D are IR
 P-tunnels, then condition 3 above will hold with respect to D only if
 the following conditions all hold as well:
 o  N has received and installed a Leaf A-D route from D, whose route
    key is K1, and which carries an IP-address-specific RT identifying
    N,
 o  N has received and installed a Leaf A-D route from D, whose route
    key is K2, and which carries an IP-address-specific RT identifying
    N,
 o  Those two Leaf A-D routes specify the same MPLS label in their
    respective PTAs.

7.3. Intra-AS I-PMSI A-D Route

 When a router joins a set of IR P-tunnels using the procedures of
 Section 4.1.2 of this document, the procedures of Section 9.1.1 of
 [RFC6513] cannot be applied, no matter what the label allocation
 policy is.  In this case, the ingress PE is the same as the UMH, but
 it is not possible to assign a label uniquely to a particular ingress
 PE or UMH.  However, the label in the MPLS Label field of the PTA
 MUST NOT appear in the MPLS Label field of the PTA carried by any
 other route originated by the same router.

8. How a Child Node Prunes Itself from an IR P-Tunnel

 If a particular IR P-tunnel was joined via the procedures of
 Section 4.1.2, a router can prune itself from the P-tunnel by
 withdrawing the Intra-AS I-PMSI A-D route it used to join the
 P-tunnel.  This is not usually done unless the router is removing
 itself entirely from a particular MVPN.

Rosen, et al. Standards Track [Page 17] RFC 7988 IR Tunnels in MVPN October 2016

 The procedures in the remainder of this section apply when a router
 joined a particular IR P-tunnel by originating a Leaf A-D route (as
 described in Sections 4.1.1 or 4.2).
 If a router no longer has a need to receive any multicast data from a
 given IR P-tunnel, it may prune itself from the P-tunnel by
 withdrawing the Leaf A-D route it used to join the tunnel.  This is
 done, e.g., if the router no longer needs any of the flows traveling
 over the P-tunnel, or if all the flows the router does need are being
 received over other P-tunnels.
 A router that is attached to a particular IR P-tunnel via a
 particular parent node may determine that it needs to stay joined to
 that IR P-tunnel but via a different parent node.  This can happen,
 for example, if there is a change in the Next Hop or the P2MP
 Segmented Next-Hop Extended Community of the S-PMSI A-D route in
 which that P-tunnel was advertised.  In this case, the router changes
 the Route Target of the Leaf A-D route it used to join the IR
 P-tunnel, so that the Route Target now identifies the new parent
 node.
 A parent node must notice when a child node has been pruned from a
 particular tree, as this will affect the parent node's multicast data
 state.  Note that the pruning of a child node may appear to the
 parent node as the explicit withdrawal of a Leaf A-D route, or it may
 appear as a change in the Route Target of a Leaf A-D route.  If the
 Route Target of a particular Leaf A-D route previously identified a
 particular parent node, but changes so that it no longer does so, the
 effect on the multicast state of the parent node is the same as if
 the Leaf A-D route had been explicitly withdrawn.

9. Parent Node Actions upon Receiving Leaf A-D Route

 These actions are detailed in [RFC6514] and [RFC7524].  Two points of
 clarification are made:
 o  If a router R1 receives and installs a Leaf A-D route originated
    by router R2, R1's multicast state is affected only if the Leaf
    A-D route carries an "IP-address-specific RT" (or "IPv6-address-
    specific RT") whose Global Administrator field identifies R1.
    (This is as specified in [RFC6514] and [RFC7524].)  If a Leaf A-D
    route's RT does not identify R1, but then changes so that it does
    identify R1, R1 must take the same actions it would take if the
    Leaf A-D route were newly received.

Rosen, et al. Standards Track [Page 18] RFC 7988 IR Tunnels in MVPN October 2016

 o  It is possible that router R1 will receive and install a Leaf A-D
    route originated by router R2, where:
  • the route's RT identifies R1,
  • the route's NLRI contains a route key whose first octet

indicates that it is identifying a P-tunnel advertised in an

       S-PMSI A-D route,
  • R1 has neither originated nor installed any such S-PMSI A-D

route.

 If at some later time, R1 installs the corresponding S-PMSI A-D
 route, and the Leaf A-D route is still installed, and the Leaf A-D
 route's RT still identifies R1, then R1 MUST follow the same
 procedures it would have followed if the S-PMSI A-D route had been
 installed before the Leaf A-D route was installed.  Implementers must
 not assume that events occur in the "usual" or "expected" order.

10. Use of Timers When Switching UMH

 Consider a child node that has joined a particular IR P-tunnel via a
 particular UMH.  To do so, it will have originated a Leaf A-D route
 with an RT that identifies the UMH.  Suppose the child node now
 determines (for whatever reason) that it needs to change its UMH for
 that P-tunnel.  It does this by:
 o  modifying the RT of the Leaf A-D route, so that the RT now
    identifies the new parent rather than the old one, and by
 o  modifying the PTA of the Leaf A-D route, changing the MPLS Label
    field as discussed in Section 7.
 Note that, in accordance with the procedures of [RFC6514] and of
 Section 4 of this document, the NLRI of the Leaf A-D route is not
 modified; only the RT and the PTA are changed.
 It is desirable for such a "switch of UMH" to be done using a "make
 before break" technique, so that the old UMH does not stop
 transmitting packets of the given P-tunnel to the child until the new
 UMH has a chance to start transmitting packets of the given P-tunnel
 to the child.  However, the control-plane operation (i.e., modifying
 the RT and PTA of the Leaf A-D route) does not permit the child node
 to first join the IR P-tunnel via the new UMH, and then later prune
 itself from the old UMH.  Rather, a single control-plane operation
 has both effects.

Rosen, et al. Standards Track [Page 19] RFC 7988 IR Tunnels in MVPN October 2016

 Therefore, the old UMH MUST continue transmitting to the child node
 for a period of time after it sees the child's Leaf A-D route being
 withdrawn (or its RT changing to identify a different UMH).  This
 timer (the "parent-continues" timer) SHOULD have a default value of
 60 seconds and SHOULD be configurable.
 By the procedures of Section 7, the child node will have advertised a
 different label for the IR P-tunnel to the new UMH than it had
 advertised to the old UMH.  This allows it to distinguish the packets
 of that IR P-tunnel transmitted by the new UMH from packets of that
 IR P-tunnel transmitted by the old UMH.  At any given time, the child
 node will accept packets of that IR P-tunnel from only one parent
 node and will discard packets of that IR P-tunnel that are received
 from the other.  To achieve "make before break" functionality, the
 child node needs to continue to accept packets from the old UMH for a
 period of time.  After this period, it will discard any packets from
 the given IR P-tunnel that it receives from the old UMH and will only
 accept such packets from the new UMH.
 Once the child node modifies the RT of its Leaf A-D route, it MUST
 run a timer (the "switch-parents-delay" timer).  This timer SHOULD
 default to 30 seconds and SHOULD be configurable.  The child node
 MUST continue to accept packets of the given IR P-tunnel from the old
 UMH until the timer expires.  However, once the child node receives a
 packet of the given IR P-tunnel from the new UMH, it MAY consider the
 "switch-parents-delay" timer to have expired.
 The "parent-continues" timer MUST be longer than the "switch-parents-
 delay" timer.  Note that both timers are specific to a given IR
 P-tunnel.

11. Security Considerations

 No security considerations are raised by this document beyond those
 already discussed in [RFC6513] and [RFC6514].

Rosen, et al. Standards Track [Page 20] RFC 7988 IR Tunnels in MVPN October 2016

12. References

12.1. Normative References

 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119,
            DOI 10.17487/RFC2119, March 1997,
            <http://www.rfc-editor.org/info/rfc2119>.
 [RFC6513]  Rosen, E., Ed., and R. Aggarwal, Ed., "Multicast in
            MPLS/BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513,
            February 2012, <http://www.rfc-editor.org/info/rfc6513>.
 [RFC6514]  Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
            Encodings and Procedures for Multicast in MPLS/BGP IP
            VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
            <http://www.rfc-editor.org/info/rfc6514>.
 [RFC6515]  Aggarwal, R. and E. Rosen, "IPv4 and IPv6 Infrastructure
            Addresses in BGP Updates for Multicast VPN", RFC 6515,
            DOI 10.17487/RFC6515, February 2012,
            <http://www.rfc-editor.org/info/rfc6515>.

12.2. Informative References

 [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
            and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
            Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
            <http://www.rfc-editor.org/info/rfc3209>.
 [RFC5036]  Andersson, L., Ed., Minei, I., Ed., and B. Thomas, Ed.,
            "LDP Specification", RFC 5036, DOI 10.17487/RFC5036,
            October 2007, <http://www.rfc-editor.org/info/rfc5036>.
 [RFC6388]  Wijnands, IJ., Ed., Minei, I., Ed., Kompella, K., and B.
            Thomas, "Label Distribution Protocol Extensions for Point-
            to-Multipoint and Multipoint-to-Multipoint Label Switched
            Paths", RFC 6388, DOI 10.17487/RFC6388, November 2011,
            <http://www.rfc-editor.org/info/rfc6388>.
 [RFC6625]  Rosen, E., Ed., Rekhter, Y., Ed., Hendrickx, W., and R.
            Qiu, "Wildcards in Multicast VPN Auto-Discovery Routes",
            RFC 6625, DOI 10.17487/RFC6625, May 2012,
            <http://www.rfc-editor.org/info/rfc6625>.

Rosen, et al. Standards Track [Page 21] RFC 7988 IR Tunnels in MVPN October 2016

 [RFC7524]  Rekhter, Y., Rosen, E., Aggarwal, R., Morin, T.,
            Grosclaude, I., Leymann, N., and S. Saad, "Inter-Area
            Point-to-Multipoint (P2MP) Segmented Label Switched Paths
            (LSPs)", RFC 7524, DOI 10.17487/RFC7524, May 2015,
            <http://www.rfc-editor.org/info/rfc7524>.
 [RFC7582]  Rosen, E., Wijnands, IJ., Cai, Y., and A. Boers,
            "Multicast Virtual Private Network (MVPN): Using
            Bidirectional P-Tunnels", RFC 7582, DOI 10.17487/RFC7582,
            July 2015, <http://www.rfc-editor.org/info/rfc7582>.
 [RFC7716]  Zhang, J., Giuliano, L., Rosen, E., Ed., Subramanian, K.,
            and D. Pacella, "Global Table Multicast with BGP Multicast
            VPN (BGP-MVPN) Procedures", RFC 7716,
            DOI 10.17487/RFC7716, December 2015,
            <http://www.rfc-editor.org/info/rfc7716>.
 [RFC7740]  Zhang, Z., Rekhter, Y., and A. Dolganow, "Simulating
            Partial Mesh of Multipoint-to-Multipoint (MP2MP) Provider
            Tunnels with Ingress Replication", RFC 7740,
            DOI 10.17487/RFC7740, January 2016,
            <http://www.rfc-editor.org/info/rfc7740>.
 [RFC7900]  Rekhter, Y., Ed., Rosen, E., Ed., Aggarwal, R., Cai, Y.,
            and T. Morin, "Extranet Multicast in BGP/IP MPLS VPNs",
            RFC 7900, DOI 10.17487/RFC7900, June 2016,
            <http://www.rfc-editor.org/info/rfc7900>.

Rosen, et al. Standards Track [Page 22] RFC 7988 IR Tunnels in MVPN October 2016

Acknowledgments

 The authors wish to thank Yakov Rekhter for his contributions to this
 work.  We also wish to thank Huajin Jeng and Samir Saad for their
 contributions, and to thank Thomas Morin for pointing out (both
 before and after the document was written) some of the issues that
 needed further elaboration.  We also thank Lucy Yong for her review
 and comments.
 Section 7.1 discusses the importance of having an MPLS label
 allocation policy that, when ingress replication is used, allows an
 egress PE to infer the identity of a received packet's ingress PE.
 This issue was first raised in earlier work by Xu Xiaohu.

Authors' Addresses

 Eric C. Rosen (editor)
 Juniper Networks, Inc.
 10 Technology Park Drive
 Westford, Massachusetts  01886
 United States of America
 Email: erosen@juniper.net
 Karthik Subramanian
 Sproute Networks
 Email: karthik@sproute.com
 Zhaohui Zhang
 Juniper Networks, Inc.
 10 Technology Park Drive
 Westford, Massachusetts  01886
 United States of America
 Email: zzhang@juniper.net

Rosen, et al. Standards Track [Page 23]

/data/webs/external/dokuwiki/data/pages/rfc/rfc7988.txt · Last modified: 2016/10/07 04:36 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki