GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc7524

Internet Engineering Task Force (IETF) Y. Rekhter Request for Comments: 7524 E. Rosen Category: Standards Track Juniper Networks ISSN: 2070-1721 R. Aggarwal

                                                                Arktan
                                                              T. Morin
                                                         I. Grosclaude
                                                                Orange
                                                            N. Leymann
                                                   Deutsche Telekom AG
                                                               S. Saad
                                                                  AT&T
                                                              May 2015
               Inter-Area Point-to-Multipoint (P2MP)
               Segmented Label Switched Paths (LSPs)

Abstract

 This document describes procedures for building inter-area point-to-
 multipoint (P2MP) segmented service label switched paths (LSPs) by
 partitioning such LSPs into intra-area segments and using BGP as the
 inter-area routing and Label Distribution Protocol (LDP).  Within
 each IGP area, the intra-area segments are either carried over intra-
 area P2MP LSPs, using P2MP LSP hierarchy, or instantiated using
 ingress replication.  The intra-area P2MP LSPs may be signaled using
 P2MP RSVP-TE or P2MP multipoint LDP (mLDP).  If ingress replication
 is used within an IGP area, then (multipoint-to-point) LDP LSPs or
 (point-to-point) RSVP-TE LSPs may be used in the IGP area.  The
 applications/services that use such inter-area service LSPs may be
 BGP Multicast VPN, Virtual Private LAN Service (VPLS) multicast, or
 global table multicast over MPLS.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 5741.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc7524.

Rekhter, et al. Standards Track [Page 1] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

Copyright Notice

 Copyright (c) 2015 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Rekhter, et al. Standards Track [Page 2] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

Table of Contents

 1. Introduction ....................................................5
 2. Specification of Requirements ...................................5
 3. General Assumptions and Terminology .............................6
 4. Inter-Area P2MP Segmented Next-Hop Extended Community ...........7
 5. Discovering P2MP FEC of Inter-Area P2MP Service LSP .............8
    5.1. BGP MVPN ...................................................8
         5.1.1. Routes Originated by PE or ASBR .....................9
         5.1.2. Routes Re-advertised by PE or ASBR ..................9
         5.1.3. Inter-Area Routes ...................................9
    5.2. LDP VPLS with BGP Auto-discovery or BGP VPLS ..............10
         5.2.1. Routes Originated by PE or ASBR ....................10
         5.2.2. Routes Re-advertised by PE or ASBR .................11
         5.2.3. Inter-Area Routes ..................................11
    5.3. Global Table Multicast over MPLS ..........................12
 6. Egress PE/ASBR Signaling Procedures ............................13
    6.1. Determining the Upstream ABR/PE/ASBR (Upstream Node) ......13
         6.1.1. Upstream Node for MVPN or VPLS .....................13
         6.1.2. Upstream Node for Global Table Multicast ...........14
    6.2. Originating a Leaf A-D Route ..............................15
         6.2.1. Leaf A-D Route for MVPN and VPLS ...................15
         6.2.2. Leaf A-D Route for Global Table Multicast ..........15
         6.2.3. Constructing the Rest of the Leaf A-D Route ........17
    6.3. PIM-SM in ASM Mode for Global Table Multicast .............18
         6.3.1. Option 1 ...........................................18
                6.3.1.1. Originating Source Active A-D Routes ......18
                6.3.1.2. Receiving BGP Source Active A-D
                         Route by PE ...............................19
                6.3.1.3. Handling (S,G,rpt) State ..................19
         6.3.2. Option 2 ...........................................19
                6.3.2.1. Originating Source Active A-D Routes ......19
                6.3.2.2. Receiving BGP Source Active A-D Route .....20
                6.3.2.3. Pruning Sources Off the Shared Tree .......20
                6.3.2.4. More on Handling (S,G,rpt) State ..........21
 7. Egress ABR Procedures ..........................................21
    7.1. Handling Leaf A-D Route on Egress ABR .....................21
    7.2. P2MP LSP as the Intra-Area LSP in the Egress Area .........23
         7.2.1. Received Leaf A-D Route Is for MVPN or VPLS ........23
         7.2.2. Received Leaf A-D Route Is for Global Table
                Multicast ..........................................24
                7.2.2.1. Global Table Multicast and S-PMSI
                         A-D Routes ................................24
                7.2.2.2. Global Table Multicast and
                         Wildcard S-PMSI A-D Routes ................25
         7.2.3. Global Table Multicast and the Expected
                Upstream Node ......................................25

Rekhter, et al. Standards Track [Page 3] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

         7.2.4. P2MP LDP LSP as the Intra-Area P2MP LSP ............26
         7.2.5. P2MP RSVP-TE LSP as the Intra-Area P2MP LSP ........26
    7.3. Ingress Replication in the Egress Area ....................26
 8. Ingress ABR Procedures .........................................27
    8.1. P2MP LSP as the Intra-Area LSP in the Backbone Area .......27
    8.2. Ingress Replication in the Backbone Area ..................27
 9. Ingress PE/ASBR Procedures .....................................28
    9.1. P2MP LSP as the Intra-Area LSP in the Ingress Area ........28
    9.2. Ingress Replication in the Ingress Area ...................29
 10. Common Tunnel Type in the Ingress and Egress Areas ............29
 11. Placement of Ingress and Egress PEs ...........................30
 12. MVPN with Virtual Hub-and-Spoke ...............................31
 13. Data Plane ....................................................31
    13.1. Data Plane Procedures on ABRs ............................31
    13.2. Data Plane Procedures on Egress PEs ......................32
    13.3. Data Plane Procedures on Ingress PEs .....................33
    13.4. Data Plane Procedures on Transit Routers .................33
 14. Support for Inter-Area Transport LSPs .........................33
    14.1. "Transport Tunnel" Tunnel Type ...........................33
    14.2. Discovering Leaves of the Inter-Area P2MP Service LSP ....34
    14.3. Discovering P2MP FEC of P2MP Transport LSP ...............34
    14.4. Egress PE Procedures for P2MP Transport LSP ..............35
    14.5. ABRs and Ingress PE Procedures for P2MP Transport LSP ....35
    14.6. Discussion ...............................................36
 15. IANA Considerations ...........................................38
 16. Security Considerations .......................................38
 17. References ....................................................39
    17.1. Normative References .....................................39
    17.2. Informative References ...................................41
 Acknowledgements ..................................................41
 Authors' Addresses ................................................42

Rekhter, et al. Standards Track [Page 4] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

1. Introduction

 This document describes procedures for building inter-area point-to-
 multipoint (P2MP) segmented service LSPs by partitioning such LSPs
 into intra-area segments and using BGP as the inter-area routing and
 label distribution protocol.  Within each IGP area, the intra-area
 segments are either carried over intra-area P2MP LSPs, potentially
 using P2MP LSP hierarchy, or instantiated using ingress replication.
 The intra-area P2MP LSPs may be signaled using P2MP RSVP-TE [RFC4875]
 or P2MP mLDP [RFC6388].  If ingress replication is used in an IGP
 area, then (multipoint-to-point) LDP LSPs [RFC5036] or (point-to-
 point) RSVP-TE LSPs [RFC3209] may be used within the IGP area.  The
 applications/services that use such inter-area service LSPs may be
 BGP Multicast VPN (BGP MVPN), VPLS multicast, or global table
 multicast over MPLS.
 The primary use case of such segmented P2MP service LSPs is when the
 Provider Edge (PE) routers are in different areas but in the same
 Autonomous System (AS) and thousands or more of PEs require P2MP
 connectivity.  For instance, this may be the case when MPLS is pushed
 further to the metro edge and the metros are in different IGP areas.
 This may also be the case when a service provider's network comprises
 multiple IGP areas in a single AS, with a large number of PEs.
 Seamless MPLS is the industry term to address this case
 [SEAMLESS-MPLS].  Thus, one of the applicabilities of this document
 is that it describes the multicast procedures for seamless MPLS.
 It is to be noted that [RFC6514] and [RFC7117] already specify
 procedures for building segmented inter-AS P2MP service LSPs.  This
 document complements those procedures, as it extends the segmented
 P2MP LSP model such that it is applicable to inter-area P2MP service
 LSPs as well.  In fact, an inter-AS deployment could use inter-AS
 segmented P2MP LSPs as specified in [RFC6514] and [RFC7117] where
 each intra-AS segment is constructed using inter-area segmented P2MP
 LSPs, as specified in this document.

2. Specification of Requirements

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in [RFC2119].

Rekhter, et al. Standards Track [Page 5] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

3. General Assumptions and Terminology

 The reader is assumed to be familiar with MVPN procedures and
 terminology [RFC6513] [RFC6514] and VPLS procedures and terminology
 [RFC7117].
 This document allows Area Border Routers (ABRs), acting as Route
 Reflectors, to follow the procedures specified in [SEAMLESS-MPLS]
 when handling the BGP Next Hop of the routes to the PEs.
 Specifically, when reflecting such routes from the non-backbone areas
 into the backbone area, the ABRs MUST set the BGP Next Hop to their
 own loopback addresses (next-hop-self), while when reflecting such
 routes from the backbone area into the non-backbone areas, the ABRs
 SHOULD NOT change the BGP Next Hop addresses (next-hop-unchanged).
 While this document allows ABRs to follow the procedures specified in
 [SEAMLESS-MPLS], procedures specified in this document are applicable
 even when ABRs do not follow the procedures specified in
 [SEAMLESS-MPLS].
 This document specifies a particular way of supporting the global
 table multicast service.  Although the document refers to this
 approach simply as "global table multicast", it does not mean to
 imply that there are no other ways to support global table multicast.
 An alternative way to support global table multicast is to use the
 procedures for MVPN that are specified in [RFC6514] and in this
 document.  That alternative is discussed in more detail in [GTM].
 However, that alternative is not further considered in the current
 document.
 This document assumes that, in the context of global table multicast,
 ABRs do not carry routes to the destinations external to their own
 AS.  Furthermore, in the context of global table multicast, this
 document assumes that an Autonomous System Border Router (ASBR), when
 re-advertising into Internal BGP (IBGP) routes received from an
 external speaker (received via External BGP (EBGP)), may not change
 the BGP Next Hop to self.
 Within an AS, a P2MP service LSP is partitioned into three segments:
 ingress area segment, backbone area segment, and egress area segment.
 Within each area, a segment is carried over an intra-area P2MP LSP or
 instantiated using ingress replication.
 When intra-area P2MP LSPs are used to instantiate the intra-area
 segments, there could be either 1:1 or n:1 mapping between intra-area
 segments of the inter-area P2MP service LSP and a given intra-area
 P2MP LSP.  The latter is realized using P2MP LSP hierarchy with

Rekhter, et al. Standards Track [Page 6] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 upstream-assigned labels [RFC5331].  For simplicity of presentation,
 we assume that P2MP LSP hierarchy is used even with 1:1 mapping; in
 which case, an Implicit NULL is used as the upstream-assigned label.
 When intra-area segments of the inter-area P2MP service LSP are
 instantiated using ingress replication, multiple such segments may be
 carried in the same P2P RSVP-TE or MP2P LDP LSP.  This can be
 achieved using downstream-assigned labels alone.
 The ingress area segment of a P2MP service LSP is rooted at a PE (or
 at an ASBR in the case where the P2MP service LSP spans multiple
 ASes).  The leaves of this segment are other PEs/ASBRs and ABRs in
 the same area as the root PE.
 The backbone area segment is rooted at either an ABR that is
 connected to the ingress area (ingress ABR), an ASBR if the ASBR is
 present in the backbone area, or a PE if the PE is present in the
 backbone area.  The backbone area segment has its leaf ABRs that are
 connected to the egress area(s) or PEs in the backbone area, or ASBRs
 in the backbone area.
 The egress area segment is rooted at an ABR in the egress area
 (egress ABR), and has its leaf PEs and ASBR in that egress area (the
 latter covers the case where the P2MP service LSP spans multiple
 ASes).  For a given P2MP service LSP, note that there may be more
 than one backbone segment, each rooted at its own ingress ABR, and
 more than one egress area segment, each rooted at its own egress ABR.
 This document uses the term "A-D routes" for "auto-discovery routes".
 An implementation that supports this document MUST implement the
 procedures described in the following sections to support inter-area
 P2MP segmented service LSPs.

4. Inter-Area P2MP Segmented Next-Hop Extended Community

 This document defines a new Transitive IPv4-Address-Specific Extended
 Community Sub-Type: "Inter-Area P2MP Next-Hop".  This document also
 defines a new BGP Transitive IPv6-Address-Specific Extended Community
 Sub-Type: "Inter-Area P2MP Next-Hop".

Rekhter, et al. Standards Track [Page 7] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 A PE, an ABR, or an ASBR constructs the Inter-Area P2MP Segmented
 Next-Hop Extended Community as follows:
  1. The Global Administrator field MUST be set to an IP address of the

PE, ABR, or ASBR that originates or advertises the route carrying

    the P2MP Next-Hop Extended Community.  For example this address
    may be the loopback address or the PE, ABR, or ASBR that
    advertises the route.
  1. The Local Administrator field MUST be set to 0.
    If the Global Administrator field is an IPv4 address, the
    IPv4-Address-Specific Extended Community is used; if the Global
    Administrator field is an IPv6 address, the IPv6-Address-Specific
    Extended Community is used.
    The detailed usage of these Extended Communities is described in
    the following sections.

5. Discovering P2MP FEC of Inter-Area P2MP Service LSP

 Each inter-area P2MP service LSP has associated with it P2MP
 Forwarding Equivalence Class (FEC).  The egress PEs need to learn
 this P2MP FEC in order to initiate the creation of the egress area
 segment of the P2MP inter-area service LSP.
 The P2MP FEC of the inter-area P2MP LSP is learned by the egress PEs
 either by configuration or based on the application-specific
 procedures (e.g., MVPN-specific procedures or VPLS-specific
 procedures).

5.1. BGP MVPN

 Egress PEs and/or ASBRs discover the P2MP FEC of the service LSPs
 used by BGP MVPN using the Inclusive Provider Multicast Service
 Interface (I-PMSI) or Selective PMSI (S-PMSI) A-D routes that are
 originated by the ingress PEs or ASBRs following the procedures of
 [RFC6514], along with modifications as described in this document.
 The Network Layer Reachability Information (NLRI) of such routes
 encodes the P2MP FEC.
 The procedures in this document require that at least one ABR in a
 given IGP area act as a Route Reflector for MVPN A-D routes.  Such a
 Router Reflector is responsible for re-advertising MVPN A-D routes
 across area boundaries.  When re-advertising these routes across area
 boundaries, this Route Reflector MUST follow the procedures in this

Rekhter, et al. Standards Track [Page 8] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 document.  Note that such a Route Reflector may also re-advertise
 MVPN A-D routes within the same area; in which case, it follows the
 plain BGP Route Reflector procedures [RFC4456].

5.1.1. Routes Originated by PE or ASBR

 The "Leaf Information Required" flag MUST be set in the PMSI Tunnel
 attribute carried in the MVPN A-D routes, when originated by the
 ingress PEs or ASBRs, except for the case where (a) as a matter of
 policy (provisioned on the ingress PEs or ASBRs) there is no
 aggregation of ingress area segments of the service LSPs and (b) mLDP
 is used as the protocol to establish intra-area transport LSPs in the
 ingress area.  Before any Leaf A-D route is advertised by a PE or ABR
 in the same area, as described in the following sections, an
 I-PMSI/S-PMSI A-D route is advertised either with an explicit Tunnel
 Type and Tunnel Identifier in the PMSI Tunnel attribute, if the
 Tunnel Identifier has already been assigned, or with a special Tunnel
 Type of "No tunnel information present" otherwise.

5.1.2. Routes Re-advertised by PE or ASBR

 When the I-PMSI/S-PMSI A-D routes are re-advertised by an ingress
 ABR, the "Leaf Information Required" flag MUST be set in the PMSI
 Tunnel attribute present in the routes, except for the case where
 (a) as a matter of policy (provisioned on the ingress ABR) there is
 no aggregation of backbone area segments of the service LSPs and
 (b) mLDP is used as the protocol to establish intra-area transport
 LSPs in the backbone area.  Likewise, when the I-PMSI/S-PMSI A-D
 routes are re-advertised by an egress ABR, the "Leaf Information
 Required" flag MUST be set in the PMSI Tunnel attribute present in
 the routes, except for the case where (a) as a matter of policy
 (provisioned on the egress ABR) there is no aggregation of egress
 area segments of the service LSPs and (b) mLDP is used as the
 protocol to establish intra-area transport LSPs in the egress area.
 Note that the procedures in the above paragraph apply when intra-area
 segments are realized by either intra-area P2MP LSPs or by ingress
 replication.

5.1.3. Inter-Area Routes

 When BGP MVPN I-PMSI or S-PMSI A-D routes are advertised or
 propagated to signal inter-area P2MP service LSPs, to indicate that
 these LSPs should be segmented using the procedures specified in this
 document, these routes MUST carry the Inter-Area P2MP Segmented
 Next-Hop Extended Community.  This Extended Community MUST be
 included in the I-PMSI/S-PMSI A-D route by the PE that originates
 such a route, or an ASBR that re-advertises such a route into its own

Rekhter, et al. Standards Track [Page 9] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 AS.  The Global Administrator field in this Extended Community MUST
 be set to the advertising PE or ASBR's IP address.  This Extended
 Community MUST also be included by ABRs as they re-advertise such
 routes.  An ABR MUST set the Global Administrator field of the Inter-
 Area P2MP Segmented Next-Hop Extended Community to its own IP
 address.  Presence of this Extended Community in the I-PMSI/S-PMSI
 A-D routes indicates to ABRs and PEs/ASBRs that they have to follow
 the procedures in this document when these procedures differ from
 those in [RFC6514].
 If an ASBR receives from an IBGP peer an I-PMSI or S-PMSI A-D route
 that carries the Inter-Area P2MP Segmented Next-Hop Extended
 Community, then before re-advertising this route to an EBGP peer, the
 ASBR SHOULD remove this Extended Community from the route.
 Suppose an ASBR receives an I-PMSI/S-PMSI A-D route from an EBGP
 peer, and this route carries the Inter-Area P2MP Segmented Next-Hop
 Extended Community.  If the inter-area P2MP service LSP signaled by
 this route should not be segmented, then before re-advertising this
 route to its IBGP peers, the ASBR MUST remove this Extended Community
 from the route.
 To avoid requiring ABRs to participate in the propagation of
 C-multicast routes, this document requires that ABRs MUST NOT modify
 the BGP Next Hop when re-advertising Inter-AS I-PMSI A-D routes.  For
 consistency, this document requires that ABRs MUST NOT modify the BGP
 Next Hop when re-advertising either Intra-AS or Inter-AS
 I-PMSI/S-PMSI A-D routes.  The egress PEs may advertise the
 C-multicast routes to RRs that are different than the ABRs.  However,
 ABRs can still be configured to be the Route Reflectors for
 C-multicast routes; in which case, they will participate in the
 propagation of C-multicast routes.

5.2. LDP VPLS with BGP Auto-discovery or BGP VPLS

 Egress PEs discover the P2MP FEC of the service LSPs used by VPLS,
 using the VPLS A-D routes that are originated by the ingress PEs
 [RFC4761] [RFC6074] or VPLS S-PMSI A-D routes that are originated by
 the ingress PEs [RFC7117].  The NLRI of such routes encodes the
 P2MP FEC.

5.2.1. Routes Originated by PE or ASBR

 The "Leaf Information Required" flag MUST be set in the PMSI Tunnel
 attribute carried in the VPLS A-D routes or VPLS S-PMSI A-D routes,
 when originated by the ingress PEs or ASBRs, except for the case
 where (a) as a matter of policy (provisioned on the ingress PEs or
 ASBRs) there is no aggregation of ingress area segments of the

Rekhter, et al. Standards Track [Page 10] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 service LSPs and (b) mLDP is used as the protocol to establish intra-
 area transport LSPs in the ingress area.  Before any Leaf A-D route
 is advertised by a PE or ABR in the same area, as described in the
 following sections, a VPLS/S-PMSI A-D route is advertised either with
 an explicit Tunnel Type and Tunnel Identifier in the PMSI Tunnel
 attribute, if the Tunnel Identifier has already been assigned, or
 with a special Tunnel Type of "No tunnel information present"
 otherwise.

5.2.2. Routes Re-advertised by PE or ASBR

 When the VPLS/S-PMSI A-D routes are re-advertised by an ingress ABR,
 the "Leaf Information Required" flag MUST be set in the PMSI Tunnel
 attribute present in the routes, except for the case where (a) as a
 matter of policy (provisioned on the ingress ABR) there is no
 aggregation of backbone area segments of the service LSPs and (b)
 mLDP is used as the protocol to establish intra-area transport LSPs
 in the backbone area.  Likewise, when the VPLS/S-PMSI A-D routes are
 re-advertised by an egress ABR, the "Leaf Information Required" flag
 MUST be set in the PMSI Tunnel attribute present in the routes,
 except for the case where (a) as a matter of policy (provisioned on
 the egress ABR) there is no aggregation of egress area segments of
 the service LSPs and (b) mLDP is used as the protocol to establish
 intra-area transport LSPs in the egress area.

5.2.3. Inter-Area Routes

 When VPLS A-D routes or S-PMSI A-D routes are advertised or
 propagated to signal inter-area P2MP service LSPs, to indicate that
 these LSPs should be segmented using the procedures specified in this
 document, these routes MUST carry the Inter-Area P2MP Segmented
 Next-Hop Extended Community.  This Extended Community MUST be
 included in the A-D route by the PE or ASBR that originates such a
 route, and the Global Administrator field MUST be set to the
 advertising PE or ASBR's IP address.  This Extended Community MUST
 also be included by ABRs as they re-advertise such routes.  An ABR
 MUST set the Global Administrator field of the Inter-Area P2MP
 Segmented Next-Hop Extended Community to its own IP address.
 Presence of this Extended Community in the I-PMSI/S-PMSI A-D routes
 indicates to ABRs and PEs/ASBRs that they have to follow the
 procedures in this document when these procedures differ from those
 in [RFC7117].
 Note that the procedures in the above paragraph apply when intra-area
 segments are realized by either intra-area P2MP LSPs or by ingress
 replication.

Rekhter, et al. Standards Track [Page 11] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 The procedures in this document require that at least one ABR in a
 given area act as a Route Reflector for VPLS A-D routes.  Such a
 Router Reflector is responsible for re-advertising VPLS A-D routes
 across areas boundaries.  When re-advertising these routes across
 areas boundaries, this Route Reflector MUST follow the procedures
 in this document.  Note that such a Route Reflector may also
 re-advertise VPLS A-D routes within the same area; in which case,
 it follows plain BGP Route Reflector procedures [RFC4456].
 When re-advertising VPLS A-D routes, a Route Reflector MUST NOT
 modify the BGP Next Hop of these routes.

5.3. Global Table Multicast over MPLS

 This section describes how the egress PEs discover the P2MP FEC when
 the application is global table multicast over an MPLS-capable
 infrastructure.  In the rest of the document, we will refer to this
 application as "global table multicast".
 When Protocol Independent Multicast - Sparse Mode (PIM-SM) is used
 for non-bidirectional ASM ("Any Source Multicast") group addresses,
 this document refers to this as "PIM-SM in ASM mode".
 In the case where global table multicast uses PIM-SM in ASM mode, the
 following assumes that an inter-area P2MP service LSP could be used
 to carry traffic either on a shared (*,G) or a source (S,G) tree.
 An egress PE learns the (S/*,G) of a multicast stream as a result of
 receiving IGMP or PIM messages on one of its IP multicast interfaces.
 This (S/*,G) forms the P2MP FEC of the inter-area P2MP service LSP.
 For each such P2MP FEC, there MAY exist a distinct inter-area P2MP
 service LSP, or multiple such FECs MAY be carried over a single P2MP
 service LSP using a wildcard (*,*) S-PMSI [RFC6625].
 Note that this document does not require the use of (*,G) inter-area
 P2MP service LSPs when global table multicast uses PIM-SM in ASM
 mode.  In fact, PIM-SM in ASM mode may be supported entirely by using
 only (S,G) inter-area P2MP service LSPs.

Rekhter, et al. Standards Track [Page 12] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

6. Egress PE/ASBR Signaling Procedures

 This section describes the egress PE/ASBR procedures for constructing
 segmented inter-area P2MP LSPs.  The procedures in this section apply
 irrespective of whether the egress PE/ASBR is in a leaf IGP area, the
 backbone area, or even in the same IGP area as the ingress PE/ASBR.
 An egress PE/ASBR applies procedures specified in this section to
 MVPN I-PMSI or S-PMSI A-D routes only if these routes carry the
 Inter-Area P2MP Segmented Next-Hop Extended Community.  An egress PE
 applies procedures specified in this section to VPLS A-D routes or
 VPLS S-PMSI A-D routes only if these routes carry the Inter-Area P2MP
 Segmented Next-Hop Extended Community.
 In order to support global table multicast, an egress PE MUST be
 auto-configured to import routes that carry an AS-specific Route
 Target Extended Community ([RFC4360]) with the Global Administrator
 field set to the AS of the PE and the Local Administrator field set
 to 0.
 Once an egress PE/ASBR discovers the P2MP FEC of an inter-area
 segmented P2MP service LSP, it MUST propagate this P2MP FEC in BGP in
 order to construct the segmented inter-area P2MP service LSP.  This
 propagation uses BGP Leaf A-D routes.

6.1. Determining the Upstream ABR/PE/ASBR (Upstream Node)

 An egress PE/ASBR discovers the P2MP FEC of an inter-area P2MP
 segmented service LSP as described in Section 5.  Once the egress
 PE/ASBR discovers this P2MP FEC, it MUST determine the upstream node
 to reach such a FEC.  If the egress PE/ASBR and the ingress PE/ASBR
 are not in the same area, and the egress PE/ASBR is not in the
 backbone IGP area, then this upstream node would be an egress ABR.
 If the egress PE/ASBR is in the backbone area and the ingress PE/ASBR
 is not in the backbone area, then this upstream node would be an
 ingress ABR.  If the egress PE/ASBR is in the same area as the
 ingress PE/ASBR, then this upstream node would be the ingress
 PE/ASBR.

6.1.1. Upstream Node for MVPN or VPLS

 If the application is MVPN or VPLS, then the upstream node's IP
 address is the IP address determined from the Global Administrator
 field of the Inter-Area P2MP Segmented Next-Hop Extended Community.
 As described in Section 5, this Extended Community MUST be carried in
 the MVPN or VPLS A-D route from which the P2MP FEC of the inter-area
 P2MP segmented service LSP is determined.

Rekhter, et al. Standards Track [Page 13] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

6.1.2. Upstream Node for Global Table Multicast

 If the application is global table multicast, then the unicast routes
 to multicast sources/RPs SHOULD carry the "VRF Route Import" Extended
 Community [RFC6514] where the IP address in the Global Administrator
 field is set to the IP address of the PE or ASBR advertising the
 unicast route.  The Local Administrator field of this Extended
 Community MUST be set to 0 (note that this is in contrast to the case
 of MVPN, where the Local Administrator field carries a non-zero value
 that identifies a particular VRF on a PE that originates VPN-IP
 routes).  If it is not desirable to advertise the VRF Route Import
 Extended Community in unicast routes, then unicast routes to
 multicast sources/RPs MUST be advertised using the multicast
 Subsequent Address Family Identifier (SAFI), i.e., SAFI 2, and such
 routes MUST carry the VRF Route Import Extended Community.
 Further, if the application is global table multicast, then the BGP
 unicast routes that advertise the routes to the IP addresses of
 PEs/ASBRs/ABRs SHOULD carry the Inter-Area P2MP Segmented Next-Hop
 Extended Community.  The IP address in the Global Administrator field
 of this Extended Community MUST be set to the IP address of the PE,
 ASBR, or ABR advertising the unicast route.  The Local Administrator
 field of this Extended Community MUST be set to 0.  If it is not
 desirable to advertise the Inter-Area P2MP Segmented Next-Hop
 Extended Community in BGP unicast routes, then the BGP unicast routes
 to the IP addresses of PEs/ASBRs/ABRs MUST be advertised using the
 multicast SAFI, i.e., SAFI 2, and such routes MUST carry the Inter-
 Area P2MP Segmented Next-Hop Extended Community.  The procedures for
 handling the BGP Next Hop attribute of SAFI 2 routes are the same as
 those of handling regular unicast routes and MAY follow
 [SEAMLESS-MPLS].
 If the application is global table multicast, then in order to
 determine the upstream node address, the egress PE first determines
 the ingress PE.  In order to determine the ingress PE, the egress PE
 determines the best route to reach the S/RP.  The ingress PE address
 is the IP address determined from the Global Administrator field of
 the VRF Route Import Extended Community that is carried in this
 route.  Then, the egress PE finds the best unicast route to reach the
 ingress PE.  The upstream node address is the IP address determined
 from the Global Administrator field of the Inter-Area P2MP Segmented
 Next-Hop Extended Community that is carried in this route.

Rekhter, et al. Standards Track [Page 14] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

6.2. Originating a Leaf A-D Route

 If the P2MP FEC was derived from an MVPN or VPLS A-D route, and if
 the route carries a PMSI Tunnel attribute with the "Leaf Information
 Required" flag set, then the egress PE MUST originate a Leaf A-D
 route.
 If the P2MP FEC was derived from a global table multicast (S/*,G),
 and the upstream node's address is not the same as the egress PE,
 then the egress PE MUST originate a Leaf A-D route.

6.2.1. Leaf A-D Route for MVPN and VPLS

 If the P2MP FEC was derived from MVPN or VPLS A-D routes, then the
 Route Key field of the Leaf A-D route contains the NLRI of the A-D
 route from which the P2MP FEC was derived.  This follows procedures
 for constructing Leaf A-D routes described in [RFC6514] [RFC7117].

6.2.2. Leaf A-D Route for Global Table Multicast

 If the application is global table multicast, then the MCAST-VPN NLRI
 of the Leaf A-D route is constructed as follows.
 The Route Key field of the MCAST-VPN NLRI has the following format:
                 +-----------------------------------+
                 |      RD   (8 octets)              |
                 +-----------------------------------+
                 | Multicast Source Length (1 octet) |
                 +-----------------------------------+
                 |  Multicast Source (Variable)      |
                 +-----------------------------------+
                 |  Multicast Group Length (1 octet) |
                 +-----------------------------------+
                 |  Multicast Group   (Variable)     |
                 +-----------------------------------+
                 |  Ingress PE's IP Address          |
                 +-----------------------------------+
 RD is set to 0 for (S,G) state and all ones for (*,G) state,
 Multicast Source is set to S for (S,G) state or RP for (*,G) state,
 Multicast Group is set to G, and Multicast Source Length and
 Multicast Group Length are set to either 4 or 16 (depending on
 whether S/RP and G are IPv4 or IPv6 addresses).
 The Ingress PE's IP address is determined as described in
 Section 6.1.

Rekhter, et al. Standards Track [Page 15] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 The Originating Router's IP Address field of the MCAST-VPN NLRI is
 set to the address of the local PE (the PE that originates the
 route).
 Thus, the entire MCAST-VPN NLRI of the route has the following
 format:
                 +-----------------------------------+
                 |      Route Type = 4 (1 octet)     |
                 +-----------------------------------+
                 |         Length (1 octet)          |
                 +-----------------------------------+
                 |          RD   (8 octets)          |
                 +-----------------------------------+
                 | Multicast Source Length (1 octet) |
                 +-----------------------------------+
                 |  Multicast Source (Variable)      |
                 +-----------------------------------+
                 |  Multicast Group Length (1 octet) |
                 +-----------------------------------+
                 |  Multicast Group   (Variable)     |
                 +-----------------------------------+
                 |  Ingress PE's IP Address          |
                 +-----------------------------------+
                 |  Originating Router's IP Address  |
                 +-----------------------------------+
 Note that the encoding of the MCAST-VPN NLRI for the Leaf A-D routes
 used for global table multicast is different from the encoding used
 by the Leaf A-D routes originated in response to S-PMSI or I-PMSI A-D
 routes.  A router that receives a Leaf A-D route can distinguish
 between these two cases by examining the third octet of the MCAST-VPN
 NLRI of the route.  If the value of this octet is 0x01, 0x02, or
 0x03, then this Leaf A-D route was originated in response to an
 S-PMSI or I-PMSI A-D route.  If the value of this octet is either
 0x00 or 0xff, and octets 3 through 10 contain either all 0x00 or all
 0xff, then this is a Leaf A-D route used for global table multicast.
 When the PE deletes (S,G)/(*,G) state that was created as a result of
 receiving PIM or IGMP messages on one of its IP multicast interfaces,
 if the PE previously originated a Leaf A-D route for that state, the
 PE SHOULD withdraw that route.
 An AS with an IPv4 network may provide global table multicast service
 for customers that use IPv6, and an AS with an IPv6 network may
 provide global table multicast service for customers that use IPv4.
 Therefore, the address family of the Ingress PE's IP Address field
 and the Originating Router's IP Address field in the Leaf A-D routes

Rekhter, et al. Standards Track [Page 16] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 used for global table multicast MUST NOT be inferred from the AFI
 field of the associated MP_REACH_NLRI/MP_UNREACH_NLRI attribute of
 these routes.  The address family is determined from the length of
 the address (a length of 4 octets for IPv4 addresses or a length of
 16 octets for IPv6 addresses).
 For example, if an AS with an IPv4 network is providing IPv6
 multicast service to a customer, the Ingress PE's IP Address and
 Originating Router's IP Address in the Leaf A-D routes used for IPv6
 global table multicast will be a 4-octet IPv4 address, even though
 the AFI of those routes will have the value 2.
 Note that the Ingress PE's IP Address and the Originating Router's IP
 Address must be either both IPv4 or both IPv6 addresses; thus, they
 must be of the same length.  Since the two variable-length fields
 (Multicast Source and Multicast Group) in the Leaf A-D routes used
 for global table multicast have their own Length field, from these
 two Length fields, and the Length field of the MCAST-VPN NLRI, one
 can compute the length of the Ingress PE's IP Address field and the
 Originating Router's IP Address field.  If the computed length of
 these fields is neither 4 nor 16, the MP_REACH_NLRI attribute MUST be
 considered to be "incorrect", and MUST be handled as specified in
 Section 7 of [RFC4760].

6.2.3. Constructing the Rest of the Leaf A-D Route

 The Next Hop field of the MP_REACH_NLRI attribute of the route SHOULD
 be set to the same IP address as the one carried in the Originating
 Router's IP Address field of the route.
 When ingress replication is used to instantiate the egress area
 segment, the Leaf A-D route MUST carry a downstream-assigned label in
 the PMSI Tunnel attribute where the PMSI Tunnel Type is set to
 ingress replication.  A PE MUST assign a distinct MPLS label for each
 Leaf A-D route originated by the PE.
 To constrain distribution of this route, the originating PE
 constructs an IP-based Route Target Extended Community by placing the
 IP address of the upstream node in the Global Administrator field of
 the Extended Community, with the Local Administrator field of this
 community set to 0.  The originating PE then adds this Route Target
 Extended Community to this Leaf A-D route.  The upstream node's
 address is determined as specified in Section 6.1.
 The PE then advertises this route to the upstream node.

Rekhter, et al. Standards Track [Page 17] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

6.3. PIM-SM in ASM Mode for Global Table Multicast

 This specification allows two options for supporting global table
 multicast that are initiated using PIM-SM in ASM mode.  The first
 option does not carry IP multicast shared trees over the MPLS
 network.  The second option does carry shared trees over the MPLS
 network and provides support for switching from shared trees to
 source trees.

6.3.1. Option 1

 This option does not carry IP multicast shared trees over the MPLS
 network.  Therefore, when an (egress) PE creates (*,G) state (as a
 result of receiving PIM or IGMP messages on one of its IP multicast
 interfaces), the PE does not propagate this state using Leaf A-D
 routes.

6.3.1.1. Originating Source Active A-D Routes

 Whenever an RP that is co-located with a PE discovers a new multicast
 source (as a result of receiving PIM Register or MSDP messages), the
 RP/PE SHOULD originate a BGP Source Active A-D route.  Similarly,
 whenever, as a result of receiving MSDP messages, a PE that is not
 configured as an RP discovers a new multicast source, the PE SHOULD
 originate a BGP Source Active A-D route.  The BGP Source Active A-D
 route carries a single MCAST-VPN NLRI constructed as follows:
 + The RD in this NLRI is set to 0.
 + The Multicast Source field MUST be set to S.  The Multicast Source
   Length field is set appropriately to reflect this.
 + The Multicast Group field MUST be set to G.  The Multicast Group
   Length field is set appropriately to reflect this.
 The Route Target of this Source Active A-D route is an AS-specific
 Route Target Extended Community with the Global Administrator field
 set to the AS of the advertising RP/PE and the Local Administrator
 field set to 0.
 To constrain distribution of the Source Active A-D route to the AS of
 the advertising RP, this route SHOULD carry the NO_EXPORT Community
 ([RFC1997]).
 Using the normal BGP procedures, the Source Active A-D route is
 propagated to all other PEs within the AS.

Rekhter, et al. Standards Track [Page 18] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 Whenever the RP/PE discovers that the source is no longer active, the
 RP MUST withdraw the Source Active A-D route, if such a route was
 previously advertised by the RP.

6.3.1.2. Receiving BGP Source Active A-D Route by PE

 As a result of receiving PIM or IGMP messages on one of its IP
 multicast interfaces, when an egress PE creates in its Tree
 Information Base (TIB) a new (*,G) entry with a non-empty outgoing
 interface list that contains one or more IP multicast interfaces, the
 PE MUST check if it has any Source Active A-D routes for that G.  If
 there is such a route, S of that route is reachable via an MPLS
 interface, and the PE does not have (S,G) state in its TIB for (S,G)
 carried in the route, then the PE originates a Leaf A-D route
 carrying that (S,G), as specified in Section 6.2.2.
 When an egress PE receives a new Source Active A-D route, the PE MUST
 check if its TIB contains an (*,G) entry with the same G as carried
 in the Source Active A-D route.  If such an entry is found, S is
 reachable via an MPLS interface, and the PE does not have (S,G) state
 in its TIB for (S,G) carried in the route, then the PE originates a
 Leaf A-D route carrying that (S,G), as specified in Section 6.2.2.

6.3.1.3. Handling (S,G,rpt) State

 Creation and deletion of (S,G,rpt) state on a PE that resulted from
 receiving PIM messages on one of its IP multicast interfaces do not
 result in any BGP actions by the PE.

6.3.2. Option 2

 This option does carry IP multicast shared trees over the MPLS
 network.  Therefore, when an egress PE creates (*,G) state (as a
 result of receiving PIM or IGMP messages on one of its IP multicast
 interfaces), the PE does propagate this state using Leaf A-D routes.

6.3.2.1. Originating Source Active A-D Routes

 Whenever a PE creates an (S,G) state as a result of receiving Leaf
 A-D routes associated with the global table multicast service, if S
 is reachable via one of the IP multicast-capable interfaces, and the
 PE determines that G is in the PIM-SM in ASM mode range, the PE MUST
 originate a BGP Source Active A-D route.  The route carries a single
 MCAST-VPN NLRI constructed as follows:
 + The RD in this NLRI is set to 0.

Rekhter, et al. Standards Track [Page 19] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 + The Multicast Source field MUST be set to S.  The Multicast Source
   Length field is set appropriately to reflect this.
 + The Multicast Group field MUST be set to G.  The Multicast Group
   Length field is set appropriately to reflect this.
 The Route Target of this Source Active A-D route is an AS-specific
 Route Target Extended Community with the Global Administrator field
 set to the AS of the advertising PE and the Local Administrator field
 set to 0.
 To constrain distribution of the Source Active A-D route to the AS of
 the advertising PE, this route SHOULD carry the NO_EXPORT Community
 [RFC1997].
 Using the normal BGP procedures, the Source Active A-D route is
 propagated to all other PEs within the AS.
 Whenever the PE deletes the (S,G) state that was previously created
 as a result of receiving a Leaf A-D route for (S,G), the PE that
 deletes the state MUST also withdraw the Source Active A-D route, if
 such a route was advertised when the state was created.

6.3.2.2. Receiving BGP Source Active A-D Route

 Procedures for receiving BGP Source Active A-D routes are the same as
 with Option 1.

6.3.2.3. Pruning Sources Off the Shared Tree

 After receiving a new Source Active A-D route for (S,G), if a PE
 determines that (a) it has the (*,G) entry in its TIB, (b) the
 incoming interface (iif) list for that entry contains one of the IP
 interfaces, (c) an MPLS LSP is in the outgoing interface (oif) list
 for that entry, and (d) the PE does not originate a Leaf A-D route
 for (S,G), then the PE MUST transition the (S,G,rpt) downstream state
 to the Prune state.  [Conceptually the PIM state machine on the PE
 will act "as if" it had received Prune(S,G,Rpt) from some other PE,
 without actually having received one.]  Depending on the (S,G,rpt)
 state on the iifs, this may result in the PE using PIM procedures to
 prune S off the Shared (*,G) tree.
 Transitioning the state machine to the Prune state SHOULD be done
 after a delay that is controlled by a timer.  The value of the timer
 MUST be configurable.  The purpose of this timer is to ensure that S
 is not pruned off the shared tree until all PEs have had time to
 receive the Source Active A-D route for (S,G).

Rekhter, et al. Standards Track [Page 20] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 The PE MUST keep the (S,G,rpt) downstream state machine in the Prune
 state for as long as (a) the outgoing interface list (oif) for (*,G)
 contains an MPLS LSP, (b) the PE has at least one Source Active A-D
 route for (S,G), and (c) the PE does not originate the Leaf A-D route
 for (S,G).  Once any of these conditions become no longer valid, the
 PE MUST transition the (S,G,rpt) downstream state machine to the
 NoInfo state.
 Note that, except for the scenario described in the first paragraph
 of this section, in all scenarios relying solely on PIM procedures on
 the PE is sufficient to ensure the correct behavior when pruning
 sources off the shared tree.

6.3.2.4. More on Handling (S,G,rpt) State

 Creation and deletion of (S,G,rpt) state on a PE that resulted from
 receiving PIM messages on one of its IP multicast interfaces do not
 result in any BGP actions by the PE.

7. Egress ABR Procedures

 This section describes the egress ABR procedures for constructing
 segmented inter-area P2MP LSPs.

7.1. Handling Leaf A-D Route on Egress ABR

 When an egress ABR receives a Leaf A-D route and the Route Target
 Extended Community carried by the route contains the IP address of
 this ABR, the following procedures will be executed.
 If the value of the third octet of the MCAST-VPN NLRI of the received
 Leaf A-D route is either 0x01, 0x02, or 0x03, this indicates that the
 Leaf A-D route was originated in response to an S-PMSI or I-PMSI A-D
 route (see Section 6.2.2).  In this case, the egress ABR MUST find an
 S-PMSI or I-PMSI route whose NLRI has the same value as the Route Key
 field of the received Leaf A-D route.  If such a matching route is
 found, then the Leaf A-D route MUST be accepted.  If the Leaf A-D
 route is accepted and if it is the first Leaf A-D route update for
 the Route Key field in the route, or the withdrawal of the last Leaf
 A-D route for the Route Key field, then the following procedures will
 be executed.
 If the RD of the received Leaf A-D route is set to all zeros or all
 ones, then the received Leaf A-D route is for the global table
 multicast service.

Rekhter, et al. Standards Track [Page 21] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 If the received Leaf A-D route is the first Leaf A-D route update for
 the Route Key field carried in the route, then the egress ABR
 originates a Leaf A-D route, whose MCAST-VPN NLRI is constructed as
 follows.
 The Route Key field of the MCAST-VPN NLRI is the same as the Route
 Key field of the MCAST-VPN NLRI of the received Leaf A-D route.  The
 Originating Router's IP Address field of the MCAST-VPN NLRI is set to
 the address of the local ABR (the ABR that originates the route).
 The Next Hop field of the MP_REACH_NLRI attribute of the route SHOULD
 be set to the same IP address as the one carried in the Originating
 Router's IP Address field of the route.
 To constrain distribution of this route, the originating egress ABR
 constructs an IP-based Route Target Extended Community by placing the
 IP address of the upstream node in the Global Administrator field of
 the Extended Community, with the Local Administrator field of this
 Extended Community set to 0, and sets the Extended Communities
 attribute of this Leaf A-D route to that Extended Community.
 The upstream node's IP address is the IP address determined from the
 Global Administrator field of the Inter-Area P2MP Segmented Next-Hop
 Extended Community, where this Extended Community is obtained as
 follows.  When the Leaf A-D route is for MVPN or VPLS, this Extended
 Community is the one carried in the I-PMSI/S-PMSI A-D route that
 matches the Leaf A-D route.  When the Leaf A-D route is for global
 table multicast, this Extended Community is the one carried in the
 best unicast route to the Ingress PE.  The Ingress PE address is
 determined from the received Leaf A-D route.  The best unicast route
 MUST first be determined from multicast SAFI, i.e., SAFI 2 routes, if
 present.
 The ABR then advertises this Leaf A-D route to the upstream node in
 the backbone area.
 Mechanisms specified in [RFC4684] for constrained BGP route
 distribution can be used along with this specification to ensure that
 only the needed PE/ABR will have to process a said Leaf A-D route.
 When ingress replication is used to instantiate the backbone area
 segment, the Leaf A-D route originated by the egress ABR MUST carry a
 downstream-assigned label in the PMSI Tunnel attribute where the
 Tunnel Type is set to ingress replication.  The ABR MUST assign a
 distinct MPLS label for each Leaf A-D route that it originates.

Rekhter, et al. Standards Track [Page 22] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 In order to support global table multicast, an egress ABR MUST auto-
 configure an import AS-based Route Target Extended Community with the
 Global Administrator field set to the AS of the ABR and the Local
 Administrator field set to 0.
 If the received Leaf A-D route is the withdrawal of the last Leaf A-D
 route for the Route Key carried in the route, then the egress ABR
 must withdraw the Leaf A-D route associated with that Route Key that
 has been previously advertised by the egress ABR in the backbone
 area.

7.2. P2MP LSP as the Intra-Area LSP in the Egress Area

 This section describes procedures for using intra-area P2MP LSPs in
 the egress area.  The procedures that are common to both P2MP RSVP-TE
 and P2MP LDP are described first, followed by procedures that are
 specific to the signaling protocol.
 When P2MP LSPs are used as the intra-area LSPs, note that an existing
 intra-area P2MP LSP may be used solely for a particular inter-area
 P2MP service LSP or for other inter-area P2MP service LSPs as well.
 The choice between the two options is purely local to the egress ABR.
 The first option provides one-to-one mapping between inter-area P2MP
 service LSPs and intra-area P2MP LSPs; the second option provides
 many-to-one mapping, thus allowing the aggregation of forwarding
 state.

7.2.1. Received Leaf A-D Route Is for MVPN or VPLS

 If the value of the third octet of the MCAST-VPN NLRI of the received
 Leaf A-D route is either 0x01, 0x02, or 0x03, this indicates that the
 Leaf A-D route was originated in response to an MVPN or VPLS S-PMSI
 or I-PMSI A-D route (see Section 6.2.2).  In this case, the ABR MUST
 re-advertise in the egress area the MVPN/VPLS A-D route that matches
 the Leaf A-D route to signal the binding of the intra-area P2MP LSP
 to the inter-area P2MP service LSP.  This must be done if and only if
 (a) such a binding hasn't already been advertised or (b) the binding
 has changed.  The re-advertised route MUST carry the Inter-area P2MP
 Segmented Next-Hop Extended Community.
 The PMSI Tunnel attribute of the re-advertised route specifies either
 an intra-area P2MP RSVP-TE LSP or an intra-area P2MP LDP LSP rooted
 at the ABR and MUST also carry an upstream-assigned MPLS label.  The
 upstream-assigned MPLS label MUST be set to Implicit NULL if the
 mapping between the inter-area P2MP service LSP and the intra-area
 P2MP LSP is one-to-one.  If the mapping is many-to-one, the intra-
 area segment of the inter-area P2MP service LSP (referred to as the

Rekhter, et al. Standards Track [Page 23] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 "inner" P2MP LSP) is constructed by nesting the inter-area P2MP
 service LSP in an intra-area P2MP LSP (referred to as the "outer"
 intra-area P2MP LSP), by using P2MP LSP hierarchy based on upstream-
 assigned MPLS labels [RFC5332].
 If segments of multiple MVPN or VPLS S-PMSI service LSPs are carried
 over a given intra-area P2MP LSP, each of these segments MUST carry a
 distinct upstream-assigned label, even if all these service LSPs are
 for (C-S/*,C-G/*)s from the same MVPN/VPLS.  Therefore, an ABR
 maintains a Label Forwarding Information Base (LFIB) state for each
 such S-PMSI traversing the ABR (that applies to both the ingress and
 the egress ABRs).

7.2.2. Received Leaf A-D Route Is for Global Table Multicast

 When the RD of the received Leaf A-D route is set to all zeros or all
 ones, this is the case of inter-area P2MP service LSP being
 associated with the global table multicast service.  The procedures
 for this are described below.

7.2.2.1. Global Table Multicast and S-PMSI A-D Routes

 This section applies only if it is desired to send a particular (S,G)
 or (*,G) global table multicast flow to only those egress PEs that
 have receivers for that multicast flow.
 If the egress ABR has not previously received (and re-advertised) an
 S-PMSI A-D route for (S,G) or (*,G) that has been originated by an
 ingress PE/ASBR (see Section 9.1), then the egress ABR MUST originate
 an S-PMSI A-D route.  The PMSI Tunnel attribute of the route MUST
 contain the identity of the intra-area P2MP LSP and an upstream-
 assigned MPLS label (although this label may be an Implicit NULL --
 see Section 3).  The RD, Multicast Source Length, Multicast Source,
 Multicast Group Length (1 octet), and Multicast Group fields of the
 NLRI of this route are the same as those of the received Leaf A-D
 route.  The Originating Router's IP Address field in the S-PMSI A-D
 route is the same as the Ingress PE's IP Address field in the
 received Leaf A-D route.  The Route Target of this route is an AS-
 specific Route Target Extended Community with the Global
 Administrator field set to the AS of the advertising ABR and the
 Local Administrator field set to 0.  The route MUST carry the Inter-
 Area P2MP Segmented Next-Hop Extended Community.  This Extended
 Community is constructed following the procedures in Section 4.
 The egress ABR MUST advertise this route into the egress area.  PEs
 in the egress area that participate in the global table multicast
 will import this route based on the Route Target carried by the
 route.

Rekhter, et al. Standards Track [Page 24] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 A PE in the egress area that originated the Leaf A-D route SHOULD
 join the P2MP LSP advertised in the PMSI Tunnel attribute of the
 S-PMSI A-D route.

7.2.2.2. Global Table Multicast and Wildcard S-PMSI A-D Routes

 It may be desirable for an ingress PE to carry multiple multicast
 flows associated with the global table multicast over the same inter-
 area P2MP service LSP.  This can be achieved using wildcard, i.e.,
 (*,*) S-PMSI A-D routes [RFC6625].  An ingress PE MAY advertise a
 wildcard S-PMSI A-D route as described in Section 9.
 If the ingress PE originates a wildcard S-PMSI A-D route, and the
 egress ABR receives this route from the ingress ABR, then the egress
 ABR either (a) MUST re-advertise this route into the egress area with
 the PMSI Tunnel attribute containing the identifier of the intra-area
 P2MP LSP in the egress area and an upstream-assigned label (note that
 this label may be an Implicit NULL -- see Section 3) assigned to the
 inter-area wildcard S-PMSI or (b) MUST be able to disaggregate
 traffic carried over the wildcard S-PMSI onto the egress area (S,G)
 or (*,G) S-PMSIs.  The procedures for such disaggregation require IP
 processing on the egress ABRs.
 If the egress ABR advertises a wildcard S-PMSI A-D route into the
 egress area, this route MUST carry an AS-specific Route Target
 Extended Community with the Global Administrator field set to the AS
 of the advertising ABR and the Local Administrator field set to 0.
 PEs in the egress area that participate in the global table multicast
 will import this route.
 A PE in the egress area SHOULD join the P2MP LSP advertised in the
 PMSI Tunnel attribute of the wildcard S-PMSI A-D route if (a) the
 Originating Router's IP Address field in the S-PMSI A-D route has the
 same value as the Ingress PE's IP Address in at least one of the Leaf
 A-D routes for global table multicast originated by the PE and (b)
 the upstream ABR for the Ingress PE's IP address in that Leaf A-D
 route is the egress ABR that advertises the wildcard S-PMSI A-D
 route.

7.2.3. Global Table Multicast and the Expected Upstream Node

 If the mapping between the inter-area P2MP service LSP for global
 table multicast service and the intra-area P2MP LSP is many-to-one,
 then an egress PE must be able to determine whether a given multicast
 packet for a particular (S,G) is received from the "expected"
 upstream node.  The expected node is the node towards which the Leaf
 A-D route is sent by the egress PE.  Packets received from another
 upstream node for that (S,G) MUST be dropped.  To allow the egress PE

Rekhter, et al. Standards Track [Page 25] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 to determine the sender upstream node, the intra-area P2MP LSP MUST
 be signaled with no Penultimate Hop Popping (PHP), when the mapping
 between the inter-area P2MP service LSP for global table multicast
 service and the intra-area P2MP LSP is many-to-one.
 Further, the egress ABR MUST first push onto the label stack the
 upstream-assigned label advertised in the S-PMSI A-D route, if the
 label is not the Implicit NULL.

7.2.4. P2MP LDP LSP as the Intra-Area P2MP LSP

 The above procedures are sufficient if P2MP LDP LSPs are used as the
 intra-area P2MP LSP in the egress area.

7.2.5. P2MP RSVP-TE LSP as the Intra-Area P2MP LSP

 If P2MP RSVP-TE LSP is used as the intra-area LSP in the egress area,
 then the egress ABR can either (a) graft the leaf (whose IP address
 is specified in the received Leaf A-D route) into an existing P2MP
 LSP rooted at the egress ABR, and use that LSP for carrying traffic
 for the inter-area segmented P2MP service LSP or (b) originate a new
 P2MP LSP to be used for carrying (S,G).
 When the RD of the received Leaf A-D route is all zeros or all ones,
 the procedures are as described in Section 7.2.2.
 Note also that the SESSION object that the egress ABR would use for
 the intra-area P2MP LSP need not encode the P2MP FEC from the
 received Leaf A-D route.

7.3. Ingress Replication in the Egress Area

 When ingress replication is used to instantiate the egress area
 segment, the Leaf A-D route advertised by the egress PE MUST carry a
 downstream-assigned label in the PMSI Tunnel attribute where the
 Tunnel Type is set to ingress replication.  We will call this label
 the egress PE downstream-assigned label.
 The egress ABR MUST forward packets received from the backbone area
 intra-area segment, for a particular inter-area P2MP LSP, to all the
 egress PEs from which the egress ABR has imported a Leaf A-D route
 for the inter-area P2MP LSP.  A packet to a particular egress PE is
 encapsulated, by the egress ABR, using an MPLS label stack the bottom
 label of which is the egress PE downstream-assigned label.  The top
 label is the P2P RSVP-TE or the MP2P LDP label to reach the
 egress PE.

Rekhter, et al. Standards Track [Page 26] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 Note that these procedures ensure that an egress PE always receives
 packets only from the upstream node expected by the egress PE.

8. Ingress ABR Procedures

 When an ingress ABR receives a Leaf A-D route and the Route Target
 Extended Community carried by the route contains the IP address of
 this ABR, the ingress ABR follows the same procedures as in Section
 7, with egress ABR replaced by ingress ABR, backbone area replaced by
 ingress area, and backbone area segment replaced by ingress area
 segment.
 In order to support global table multicast, the ingress ABR MUST be
 auto-configured with an import AS-based Route Target Extended
 Community whose Global Administrator field is set to the AS of the
 ABR and whose Local Administrator field is set to 0.

8.1. P2MP LSP as the Intra-Area LSP in the Backbone Area

 The procedures for binding the backbone area segment of an inter-area
 P2MP LSP to the intra-area P2MP LSP in the backbone area are the same
 as in Sections 7 and 7.2, with egress PE being replaced by egress
 ABR, egress ABR being replaced by ingress ABR, and egress area being
 replaced by backbone area.  This applies to the inter-area P2MP LSPs
 associated with either MVPN, VPLS, or global table multicast.
 It is to be noted that, in the case of global table multicast, if the
 backbone area uses wildcard S-PMSI, then the egress area also SHOULD
 use wildcard S-PMSI for global table multicast, or the egress ABRs
 MUST be able to disaggregate traffic carried over the wildcard S-PMSI
 onto the egress area (S,G) or (*,G) S-PMSIs.  The procedures for such
 disaggregation require IP processing on the egress ABRs.

8.2. Ingress Replication in the Backbone Area

 When ingress replication is used to instantiate the backbone area
 segment, the Leaf A-D route advertised by the egress ABR MUST carry a
 downstream-assigned label in the PMSI Tunnel attribute where the
 Tunnel Type is set to ingress replication.  We will call this the
 egress ABR downstream-assigned label.  The egress ABR MUST assign a
 distinct MPLS label for each Leaf A-D route originated by the ABR.
 The ingress ABR MUST forward packets received from the ingress area
 intra-area segment, for a particular inter-area P2MP LSP, to all the
 egress ABRs from which the ingress ABR has imported a Leaf A-D route
 for the inter-area P2MP LSP.  A packet to a particular egress ABR is
 encapsulated, by the ingress ABR, using an MPLS label stack the
 bottom label of which is the egress ABR downstream-assigned label.

Rekhter, et al. Standards Track [Page 27] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 The top label is the P2P RSVP-TE or the MP2P LDP label to reach the
 egress ABR.

9. Ingress PE/ASBR Procedures

 This section describes the ingress PE/ASBR procedures for
 constructing segmented inter-area P2MP LSPs.
 When an ingress PE/ASBR receives a Leaf A-D route and the Route
 Target Extended Community carried by the route contains the IP
 address of this PE/ASBR, the following procedures will be executed.
 If the value of the third octet of the MCAST-VPN NLRI of the received
 Leaf A-D route is either 0x01, 0x02, or 0x03, this indicates that the
 Leaf A-D route was originated in response to an S-PMSI or I-PMSI A-D
 route (see Section 6.2.2).  In this case, the ingress PE/ASBR MUST
 find an S-PMSI or I-PMSI route whose NLRI has the same value as the
 Route Key field of the received Leaf A-D route.  If such a matching
 route is found, then the Leaf A-D route MUST be accepted or else it
 MUST be discarded.  If the Leaf A-D route is accepted, then it MUST
 be processed as per MVPN or VPLS procedures.
 If the RD of the received A-D route is set to all zeros or all ones,
 then the received Leaf A-D route is for the global table multicast
 service.  If this is the first Leaf A-D route for the Route Key
 carried in the route, the PIM implementation MUST set its upstream
 (S/RP,G) state machine to Joined state for the (S/RP,G) received via
 a Leaf A-D route update.  Likewise, if this is the withdrawal of the
 last Leaf A-D route whose Route Key matches a particular (S/RP,G)
 state, the PIM implementation MUST set its upstream (S/RP,G) state
 machine to Prune state for the (S/RP,G).

9.1. P2MP LSP as the Intra-Area LSP in the Ingress Area

 If the value of the third octet of the MCAST-VPN NLRI of the received
 Leaf A-D route is either 0x01, 0x02, or 0x03 (which indicates that
 the Leaf A-D route was originated in response to an S-PMSI or I-PMSI
 A-D route), and P2MP LSP is used as the intra-area LSP in the ingress
 area, then the procedures for binding the ingress area segment of the
 inter-area P2MP LSP to the intra-area P2MP LSP in the ingress area
 are the same as in Sections 7 and 7.2.
 When the RD of the received Leaf A-D route is all zeros or all ones,
 as is the case where the inter-area service P2MP LSP is associated
 with the global table multicast service, the ingress PE MAY originate
 an S-PMSI A-D route with the RD, multicast source, and multicast
 group fields being the same as those in the received Leaf A-D route.

Rekhter, et al. Standards Track [Page 28] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 Further, in the case of global table multicast, an ingress PE MAY
 originate a wildcard S-PMSI A-D route as per the procedures in
 [RFC6625] with the RD set to 0.  This route may be originated by the
 ingress PE based on configuration or based on the import of a Leaf
 A-D route with the RD set to 0.  If an ingress PE originates such a
 route, then the ingress PE MAY decide not to originate (S,G) or (*,G)
 S-PMSI A-D routes.
 The wildcard S-PMSI A-D route MUST carry the Inter-Area P2MP
 Segmented Next-Hop Extended Community.  This Extended Community is
 constructed following the procedures in Section 4.
 It is to be noted that, in the case of global table multicast, if the
 ingress area uses wildcard S-PMSI, then the backbone area also SHOULD
 use wildcard S-PMSI for global table multicast, or the ingress ABRs
 MUST be able to disaggregate traffic carried over the wildcard S-PMSI
 onto the backbone area (S,G) or (*,G) S-PMSIs.  The procedures for
 such disaggregation require IP processing on the ingress ABRs.

9.2. Ingress Replication in the Ingress Area

 When ingress replication is used to instantiate the ingress area
 segment, the Leaf A-D route advertised by the ingress ABR MUST carry
 a downstream-assigned label in the PMSI Tunnel attribute where the
 Tunnel Type is set to ingress replication.  We will call this the
 ingress ABR downstream-assigned label.  The ingress ABR MUST assign a
 distinct MPLS label for each Leaf A-D route originated by the ABR.
 The ingress PE/ASBR MUST forward packets received from the CE, for a
 particular inter-area P2MP LSP, to all the ingress ABRs from which
 the ingress PE/ASBR has imported a Leaf A-D route for the inter-area
 P2MP LSP.  A packet to a particular ingress ABR is encapsulated, by
 the ingress PE/ASBR, using an MPLS label stack the bottom label of
 which is the ingress ABR downstream-assigned label.  The top label is
 the P2P RSVP-TE or the MP2P LDP label to reach the ingress ABR.

10. Common Tunnel Type in the Ingress and Egress Areas

 For a given inter-area service P2MP LSP, the PE/ASBR that is the root
 of that LSP controls the type of the intra-area P-tunnel that carries
 the ingress area segment of that LSP.  However, the type of the
 intra-area P-tunnel that carries the backbone area segment of that
 LSP may be different from the type of the intra-area P-tunnels that
 carry the ingress area segment and the egress area segment of that
 LSP.  In that situation, if, for a given inter-area P2MP LSP, it is
 desirable/necessary to use the same type of tunnel for the intra-area
 P-tunnels that carry the ingress area segment and for the intra-area

Rekhter, et al. Standards Track [Page 29] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 P-tunnels that carry the egress area segment of that LSP, then the
 following procedures on the ingress ABR and egress ABR provide this
 functionality.
 When an ingress ABR re-advertises into the backbone area a BGP MVPN
 I-PMSI, S-PMSI A-D route, or VPLS A-D route, the ingress ABR places
 the PMSI Tunnel attribute of this route into the ATTR_SET BGP
 attribute [RFC6368], adds this attribute to the re-advertised route,
 and then replaces the original PMSI Tunnel attribute with a new one
 (note that the Tunnel Type of the new attribute may be different from
 the Tunnel Type of the original attribute).
 When an egress ABR re-advertises into the egress area a BGP MVPN
 I-PMSI or S-PMSI A-D route, or VPLS A-D route, if the route carries
 the ATTR_SET BGP attribute [RFC6368], the ABR sets the Tunnel Type of
 the PMSI Tunnel attribute in the re-advertised route to the Tunnel
 Type of the PMSI Tunnel attribute carried in the ATTR_SET BGP
 attribute, and removes the ATTR_SET from the route.

11. Placement of Ingress and Egress PEs

 As described in the earlier sections, procedures in this document
 allow the placement of ingress and egress PEs in the backbone area.
 They also allow the placement of egress PEs in the ingress area or
 the placement of ingress PEs in the egress area.
 For instance, suppose that in the ingress and egress areas, a global
 table multicast service is being provided, and the data is being sent
 over PIM-based IP/GRE P-tunnels.  Suppose also that it is desired to
 carry that data over the backbone area through MPLS P-tunnels.  This
 can be done if the ABR connecting the ingress area to the backbone
 follows the procedures that this document specifies for ingress PEs
 providing the global table multicast service, and if the ABR
 connecting the egress area to the backbone follows the procedures
 that this document specifies for egress PEs providing the global
 table multicast service.
 If MVPN service is being provided in the ingress and egress areas,
 with the MVPN data carried in PIM-based IP/GRE P-tunnels, this same
 technique enables the MVPN data to be carried over the backbone in
 MPLS P-tunnels.  The PIM-based IP/GRE P-tunnels in the ingress and
 egress areas are treated as global table multicasts, and the ABRs
 provide the ingress and egress PE functionality.

Rekhter, et al. Standards Track [Page 30] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

12. MVPN with Virtual Hub-and-Spoke

 Procedures described in this document could be used in conjunction
 with the Virtual Hub-and-Spoke procedures [RFC7024].
 This document does not place any restrictions on the placement of
 Virtual Hubs and Virtual Spokes.
 In addition to I-PMSI/S-PMSI A-D routes, the procedures described in
 this document are applicable to Associated-V-spoke-only I-PMSI A-D
 routes.
 In the scenario where a V-hub, as a result of importing an S-PMSI A-D
 route in its VRF, originates an S-PMSI A-D route targeted to its
 V-spokes (as specified in Section 7.8.2 of [RFC7024]), the V-hub
 SHOULD be able to control via configuration whether the Inter-Area
 P2MP Segmented Next-Hop Extended Community, if present in the
 received S-PMSI A-D route, should also be carried in the originated
 S-PMSI A-D route.  By default, if the received S-PMSI A-D route
 carries the Inter-Area P2MP Segmented Next-Hop Extended Community,
 then the originated S-PMSI A-D route SHOULD also carry this Extended
 Community.

13. Data Plane

 This section describes the data plane procedures on the ABRs, ingress
 PEs, egress PEs, and transit routers.

13.1. Data Plane Procedures on ABRs

 When procedures in this document are followed to signal inter-area
 P2MP segmented LSPs, ABRs are required to perform only MPLS
 switching.  When an ABR receives an MPLS packet from an "incoming"
 intra-area segment of the inter-area P2MP segmented LSP, it forwards
 the packet, based on MPLS switching, on to another "outgoing" intra-
 area segment of the inter-area P2MP segmented LSP.
 If the outgoing intra-area segment is instantiated using a P2MP LSP,
 and if there is a one-to-one mapping between the outgoing intra-area
 segment and the P2MP LSP, then the ABR MUST pop the incoming
 segment's label stack and push the label stack of the outgoing P2MP
 LSP.  If there is a many-to-one mapping between outgoing intra-area
 segments and the P2MP LSP, then the ABR MUST pop the incoming
 segment's label stack and first push the upstream-assigned label
 corresponding to the outgoing intra-area segment, if such a label has
 been assigned, and then push the label stack of the outgoing P2MP
 LSP.

Rekhter, et al. Standards Track [Page 31] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 If the outgoing intra-area segment is instantiated using ingress
 replication, then the ABR must pop the incoming segment's label stack
 and replicate the packet once to each leaf ABR or PE of the outgoing
 intra-area segment.  The label stack of the packet sent to each such
 leaf MUST first include a downstream-assigned label assigned by the
 leaf to the segment, followed by the label stack of the P2P or MP2P
 LSP to the leaf.

13.2. Data Plane Procedures on Egress PEs

 An egress PE must first identify the inter-area P2MP segmented LSP
 based on the incoming label stack.  After this identification, the
 egress PE must forward the packet using the application that is bound
 to the inter-area P2MP segmented LSP.
 Note that the application-specific forwarding for MVPN service may
 require the egress PE to determine whether the packets were received
 from the expected sender PE.  When the application is MVPN, the FEC
 of an inter-area P2MP segmented LSP is at the granularity of the
 sender PE.  Note that MVPN intra-AS I-PMSI A-D routes and S-PMSI A-D
 routes both carry the Originating Router's IP Address.  Thus, an
 egress PE could associate the data arriving on P-tunnels advertised
 by these routes with the Originating Router's IP Address carried by
 these routes, which is the same as the ingress PE.  Since a unique
 label stack is associated with each such FEC, the egress PE can
 determine the sender PE from the label stack.
 Likewise for VPLS service, for the purposes of Media Access Control
 (MAC) learning the egress, the PE must be able to determine the
 "VE-ID" (VPLS Edge Device Identifier) from which the packets have
 been received.  The FEC of the VPLS A-D routes carries the VE-ID.
 Thus, an egress PE could associate the data arriving on P-tunnels
 advertised by these routes with the VE-ID carried by these routes.
 Since a unique label stack is associated with each such FEC, the
 egress PE can perform MAC learning for packets received from a given
 VE-ID.
 When the application is global table multicast, it is sufficient for
 the label stack to include identification of the sender upstream
 node.  When P2MP LSPs are used, this requires that PHP MUST be turned
 off.  When ingress replication is used, the egress PE knows the
 incoming downstream-assigned label to which it has bound a particular
 (S/*,G) and must accept packets with only that label for that
 (S/*,G).

Rekhter, et al. Standards Track [Page 32] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

13.3. Data Plane Procedures on Ingress PEs

 An Ingress PE must perform application-specific forwarding procedures
 to identify the outgoing intra-area segment of an incoming packet.
 If the outgoing intra-area segment is instantiated using a P2MP LSP,
 and if there is a one-to-one mapping between the outgoing intra-area
 segment and the P2MP LSP, then the ingress PE MUST encapsulate the
 packet in the label stack of the outgoing P2MP LSP.  If there is a
 many-to-one mapping between outgoing intra-area segments and the P2MP
 LSP, then the PE MUST first push the upstream-assigned label
 corresponding to the outgoing intra-area segment, if such a label
 has been assigned, and then push the label stack of the outgoing
 P2MP LSP.
 If the outgoing intra-area segment is instantiated using ingress
 replication, then the PE must replicate the packet once to each leaf
 ABR or PE of the outgoing intra-area segment.  The label stack of the
 packet sent to each such leaf MUST first include a downstream-
 assigned label assigned by the leaf to the segment, followed by the
 label stack of the P2P or MP2P LSP to the leaf.

13.4. Data Plane Procedures on Transit Routers

 When procedures in this document are followed to signal inter-area
 P2MP segmented LSPs, transit routers in each area perform only MPLS
 switching.

14. Support for Inter-Area Transport LSPs

 This section describes OPTIONAL procedures that allow multiple
 (inter-area) P2MP LSPs to be aggregated into a single inter-area P2MP
 "transport LSP".  The segmentation procedures, as specified in this
 document, are then applied to these inter-area P2MP transport LSPs,
 rather than being applied directly to the individual LSPs that are
 aggregated into the transport.  In the following, the individual LSPs
 that are aggregated into a single transport LSP will be known as
 "service LSPs".

14.1. "Transport Tunnel" Tunnel Type

 For the PMSI Tunnel attribute, we define a new Tunnel Type, called
 "Transport Tunnel", whose Tunnel Identifier is a tuple <Source PE
 Address, Local Number>.  This Tunnel Type is assigned a value of 8.
 The Source PE Address is the address of the PE that originates the
 (service) A-D route that carries this attribute, and the Local Number
 is a number that is unique to the Source PE.  The length of the Local
 Number part is the same as the length of the Source PE Address.

Rekhter, et al. Standards Track [Page 33] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 Thus, if the Source PE Address is an IPv4 address, then the Local
 Number part is 4 octets; if the Source PE Address is an IPv6 address,
 then the Local Number part is 16 octets.

14.2. Discovering Leaves of the Inter-Area P2MP Service LSP

 When aggregating multiple P2MP LSPs using P2MP LSP hierarchy,
 determining the leaf nodes of the LSPs being aggregated is essential
 for being able to trade-off the overhead due to the P2MP LSPs versus
 suboptimal use of bandwidth due to the partial congruency of the LSPs
 being aggregated.
 Therefore, if a PE that is a root of a given service P2MP LSP wants
 to aggregate this LSP with other (service) P2MP LSPs rooted at the
 same PE into an inter-area P2MP transport LSP, the PE should first
 determine all the leaf nodes of that service LSP, as well as those of
 the other service LSPs being aggregated.
 To accomplish this, the PE sets the PMSI Tunnel attribute of the
 service A-D route (an I-PMSI or S-PMSI A-D route for MVPN or VPLS
 service) associated with that LSP as follows.  The Tunnel Type is set
 to "No tunnel information present", and the "Leaf Information
 Required" flag is set to 1.  The route MUST NOT carry the Inter-Area
 P2MP Segmented Next-Hop Extended Community.  In contrast to the
 procedures for the MVPN and VPLS A-D routes described so far, the
 Route Reflectors that participate in the distribution of this route
 need not be ABRs.

14.3. Discovering P2MP FEC of P2MP Transport LSP

 Once the ingress PE determines all the leaves of a given P2MP service
 LSP, the PE (using some local criteria) selects a particular inter-
 area transport P2MP LSP to be used for carrying the (inter-area)
 service P2MP LSP.
 Once the PE selects the transport P2MP LSP, the PE (re-)originates
 the service A-D route.  The PMSI Tunnel attribute of this route now
 carries the Tunnel Identifier of the selected transport LSP, with the
 Tunnel Type set to "Transport Tunnel".  If the transport LSP carries
 multiple P2MP service LSPs, then the MPLS Label field in the
 attribute carries an upstream-assigned label assigned by the PE that
 is bound to the P2MP FEC of the inter-area P2MP service LSP.
 Otherwise, this field is set to Implicit NULL.
 As described earlier, this service A-D route MUST NOT carry the
 Inter-Area P2MP Segmented Next-Hop Extended Community, and the Route
 Reflectors that participate in the distribution of this route need
 not be ABRs.

Rekhter, et al. Standards Track [Page 34] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

14.4. Egress PE Procedures for P2MP Transport LSP

 When an egress PE receives and accepts an MVPN or VPLS service A-D
 route, if the "Leaf Information Required" flag in the PMSI Tunnel
 attribute of the received A-D route is set to 1, and the route does
 not carry the Inter-Area P2MP Segmented Next-Hop Extended Community,
 then the egress PE, following the "regular" MVPN or VPLS procedures
 associated with the received A-D route (as specified in [RFC6514] and
 [RFC7117]), originates a Leaf A-D route.
 In addition, if the Tunnel Type in the PMSI Tunnel attribute of the
 received service A-D route is set to "Transport Tunnel", the egress
 PE originates yet another Leaf A-D route.
 The format of the Route Key field of the MCAST-VPN NLRI of this
 additional Leaf A-D route is the same as defined in Section 6.2.2.
 The Route Key field of the MCAST-VPN NLRI of this route is
 constructed as follows:
    RD (8 octets) - set to 0
    Multicast Source Length, Multicast Source - constructed from the
        Source PE Address part of the Tunnel Identifier carried in the
        PMSI Tunnel attribute of the received service S-PMSI A-D
        route.
    Multicast Group Length, Multicast Group - constructed from the
        Local Number part of the Tunnel Identifier carried in the PMSI
        Tunnel attribute of the received service S-PMSI A-D route.
    Ingress PE IP Address - set to the Source PE Address part of the
        Tunnel Identifier carried in the PMSI Tunnel attribute of the
        received service S-PMSI A-D route.
 The egress PE, when determining the upstream ABR, follows the
 procedures specified in Section 6.1 for global table multicast.
 The egress PE constructs the rest of the Leaf A-D route following the
 procedures specified in Section 6.2.3.
 From that point on we follow the procedures used for the Leaf A-D
 routes for global table multicast, as outlined below.

14.5. ABRs and Ingress PE Procedures for P2MP Transport LSP

 In this section, we specify ingress and egress ABRs, as well as
 ingress PE procedures for P2MP transport LSPs.

Rekhter, et al. Standards Track [Page 35] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 When an egress ABR receives the Leaf A-D route, and P2MP LSP is used
 to instantiate the egress area segment of the inter-area transport
 LSP, the egress ABR will advertise into the egress area an S-PMSI A-D
 route.  This route is constructed following the procedures in Section
 7.2.2.1.  The egress PE(s) will import this route.
 The egress ABR will also propagate, with appropriate modifications,
 the received Leaf A-D route into the backbone area.  This is
 irrespective of whether the egress area segment is instantiated using
 P2MP LSP or ingress replication.
 If P2MP LSP is used to instantiate the backbone area segment of the
 inter-area transport LSP, then an ingress ABR will advertise into the
 backbone area an S-PMSI A-D route.  This route is constructed
 following the procedures in Section 7.1.2.1.  The egress ABR(s) will
 import this route.
 The ingress ABR will also propagate, with appropriate modifications,
 the received Leaf A-D route into the ingress area towards the
 ingress/root PE.  This is irrespective of whether the backbone area
 segment is instantiated using P2MP LSP or ingress replication.
 Finally, if P2MP LSP is used to instantiate the ingress area segment,
 the ingress PE will advertise into the ingress area an S-PMSI A-D
 route with the RD, multicast source, and multicast group fields being
 the same as those in the received Leaf A-D route.  The PMSI Tunnel
 attribute of this route contains the identity of the intra-area P2MP
 LSP used to instantiate the ingress area segment, and an upstream-
 assigned MPLS label.  The ingress ABR(s) and other PE(s) in the
 ingress area, if any, will import this route.  The ingress PE will
 use the (intra-area) P2MP LSP advertised in this route for carrying
 traffic associated with the original service A-D route advertised by
 the PE.

14.6. Discussion

 Use of inter-area transport P2MP LSPs, as described in this section,
 creates a level of indirection between (inter-area) P2MP service
 LSPs, and intra-area transport LSPs that carry the service LSPs.
 Rather than segmenting (inter-area) service P2MP LSPs, and then
 aggregating (intra-area) segments of these service LSPs into intra-
 area transport LSPs, this approach first aggregates multiple (inter-
 area) service P2MP LSPs into a single inter-area transport P2MP LSP,
 then segments such inter-area transport P2MP LSPs, and then
 aggregates (intra-area) segments of these inter-area transport LSPs
 into intra-area transport LSPs.

Rekhter, et al. Standards Track [Page 36] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 On one hand, this approach could result in reducing the state (and
 the overhead associated with maintaining the state) on ABRs.  This is
 because instead of requiring ABRs to maintain state for individual
 P2MP service LSPs, ABRs would need to maintain state only for the
 inter-area P2MP transport LSPs.  Note, however, that this reduction
 is possible only if a single inter-area P2MP transport LSP aggregates
 more than one (inter-area) service LSP.  In the absence of such
 aggregation, use of inter-area transport LSPs provides no benefits,
 yet results in extra overhead.  And while such aggregation does allow
 reduced state on ABRs, it comes at a price, as described below.
 As we mentioned before, aggregating multiple P2MP service LSPs into a
 single inter-area P2MP transport LSP requires the PE rooted at these
 LSPs to determine all the leaf nodes of the service LSPs to be
 aggregated.  This means that the root PE has to track all the leaf
 PEs of these LSPs.  In contrast, when one applies segmentation
 procedures directly to the P2MP service LSPs, the root PE has to
 track only the leaf PEs in its own IGP area, plus the ingress ABR(s).
 Likewise, an ingress ABR has to track only the egress ABRs.  Finally,
 an egress ABR has to track only the leaf PEs in its own area.
 Therefore, while the total overhead of leaf tracking due to the P2MP
 service LSPs is about the same in both approaches, the distribution
 of this overhead is different.  Specifically, when one uses inter-
 area P2MP transport LSPs, this overhead is concentrated on the
 ingress PE.  When one applies segmentation procedures directly to the
 P2MP service LSPs, this overhead is distributed among the ingress PE
 and ABRs.
 Moreover, when one uses inter-area P2MP transport LSPs, ABRs have to
 bear the overhead of leaf tracking for inter-area P2MP transport
 LSPs.  In contrast, when one applies segmentation procedures directly
 to the P2MP service LSPs, there is no such overhead (as there are no
 inter-area P2MP transport LSPs).
 Use of inter-area P2MP transport LSPs may also result in more
 bandwidth inefficiency, as compared to applying segmentation
 procedures directly to the P2MP service LSPs.  This is because with
 inter-area P2MP transport LSPs the ABRs aggregate segments of inter-
 area P2MP transport LSPs, rather than segments of (inter-area) P2MP
 service LSPs.  To illustrate this, consider the following example.
 Assume PE1 in Area 1 is an ingress PE, with two multicast streams,
 (C-S1, C-G1) and (C-S2, C-G2), originated by an MVPN site connected
 to PE1.  Assume that PE2 in Area 2 has an MVPN site with receivers
 for (C-S1, C-G1), PE3 and PE4 in Area 3 have an MVPN site with
 receivers for both (C-S1, C-G1) and (C-S2, C-G2).  Finally, assume
 that PE5 in Area 4 has an MVPN site with receivers for (C-S2, C-G2).

Rekhter, et al. Standards Track [Page 37] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 When segmentation applies directly to the P2MP service LSPs, Area 2
 would have just one intra-area transport LSP that would carry the
 egress area segment of the P2MP service LSP for (C-S1, C-G1); Area 3
 would have just one intra-area transport LSP that would carry the
 egress area segments of both the P2MP service LSP for (C-S1, C-G1)
 and the P2MP service LSP for (C-S2, C-G2); Area 4 would have just one
 intra-area transport LSP that would carry the egress area segment of
 the P2MP service LSP for (C-S2, C-G2).  Note that there is no
 bandwidth inefficiency in this case at all.
 When using inter-area P2MP transport LSPs, to achieve the same state
 overhead on the routers within each of the egress areas (except for
 egress ABRs), PE1 would need to aggregate the P2MP service LSP for
 (C-S1, C-G1) and the P2MP service LSP for (C-S2, C-G2) into the same
 inter-area P2MP transport LSP.  While such aggregation would reduce
 state on ABRs, it would also result in bandwidth inefficiency, as
 (C-S1, C-G1) will be delivered not just to PE2, PE3, and PE4, but
 also to PE5, which has no receivers for this stream.  Likewise,
 (C-S2, C-G2) will be delivered not just to PE3, PE4, and PE5, but
 also to PE2, which has no receivers for this stream.

15. IANA Considerations

 This document defines a new BGP Extended Community called "Inter-Area
 P2MP Segmented Next-Hop" (see Section 4).  This may be either a
 Transitive IPv4-Address-Specific Extended Community or a Transitive
 IPv6-Address-Specific Extended Community.  IANA has assigned the
 value 0x12 in the "Transitive IPv4-Address-Specific Extended
 Community Sub-Types" registry, and IANA has assigned the value 0x0012
 in the "Transitive IPv6-Address-Specific Extended Community Types"
 registry.  This document is the reference for both code points.
 IANA has assigned the value 0x08 in the "P-Multicast Service
 Interface Tunnel (PMSI Tunnel) Tunnel Types" registry [RFC7385] as
 "Transport Tunnel" (see Section 14).
 This document makes use of a Route Distinguisher whose value is all
 ones.  The two-octet type field of this Route Distinguisher thus has
 the value 65535.  IANA has assigned this value in the "Route
 Distinguisher Type Field" registry as "For Use Only in Certain Leaf
 A-D Routes", with this document as the reference.

16. Security Considerations

 Procedures described in this document are subject to security threats
 similar to those experienced by any MPLS deployment.  It is
 recommended that baseline security measures are considered as
 described in "Security Framework for MPLS and GMPLS Networks"

Rekhter, et al. Standards Track [Page 38] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 [RFC5920], in the mLDP specification [RFC6388], and in the P2MP
 RSVP-TE specification [RFC3209].  The security considerations of
 [RFC6513] are also applicable.

17. References

17.1. Normative References

 [RFC1997]   Chandra, R., Traina, P., and T. Li, "BGP Communities
             Attribute", RFC 1997, DOI 10.17487/RFC1997, August 1996,
             <http://www.rfc-editor.org/info/rfc1997>.
 [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119,
             DOI 10.17487/RFC2119, March 1997,
             <http://www.rfc-editor.org/info/rfc2119>.
 [RFC3209]   Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
             and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
             Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
             <http://www.rfc-editor.org/info/rfc3209>.
 [RFC4360]   Sangli, S., Tappan, D., and Y. Rekhter, "BGP Extended
             Communities Attribute", RFC 4360, DOI 10.17487/RFC4360,
             February 2006, <http://www.rfc-editor.org/info/rfc4360>.
 [RFC4456]   Bates, T., Chen, E., and R. Chandra, "BGP Route
             Reflection: An Alternative to Full Mesh Internal BGP
             (IBGP)", RFC 4456, DOI 10.17487/RFC4456, April 2006,
             <http://www.rfc-editor.org/info/rfc4456>.
 [RFC4684]   Marques, P., Bonica, R., Fang, L., Martini, L., Raszuk,
             R., Patel, K., and J. Guichard, "Constrained Route
             Distribution for Border Gateway Protocol/MultiProtocol
             Label Switching (BGP/MPLS) Internet Protocol (IP) Virtual
             Private Networks (VPNs)", RFC 4684, DOI 10.17487/RFC4684,
             November 2006, <http://www.rfc-editor.org/info/rfc4684>.
 [RFC4760]   Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
             "Multiprotocol Extensions for BGP-4", RFC 4760,
             DOI 10.17487/RFC4760, January 2007,
             <http://www.rfc-editor.org/info/rfc4760>.
 [RFC4761]   Kompella, K., Ed., and Y. Rekhter, Ed., "Virtual Private
             LAN Service (VPLS) Using BGP for Auto-Discovery and
             Signaling", RFC 4761, DOI 10.17487/RFC4761, January 2007,
             <http://www.rfc-editor.org/info/rfc4761>.

Rekhter, et al. Standards Track [Page 39] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 [RFC4875]   Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.
             Yasukawa, Ed., "Extensions to Resource Reservation
             Protocol - Traffic Engineering (RSVP-TE) for Point-to-
             Multipoint TE Label Switched Paths (LSPs)", RFC 4875,
             DOI 10.17487/RFC4875, May 2007,
             <http://www.rfc-editor.org/info/rfc4875>.
 [RFC5036]   Andersson, L., Ed., Minei, I., Ed., and B. Thomas, Ed.,
             "LDP Specification", RFC 5036, DOI 10.17487/RFC5036,
             October 2007, <http://www.rfc-editor.org/info/rfc5036>.
 [RFC5331]   Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
             Label Assignment and Context-Specific Label Space",
             RFC 5331, DOI 10.17487/RFC5331, August 2008,
             <http://www.rfc-editor.org/info/rfc5331>.
 [RFC5332]   Eckert, T., Rosen, E., Ed., Aggarwal, R., and Y. Rekhter,
             "MPLS Multicast Encapsulations", RFC 5332,
             DOI 10.17487/RFC5332, August 2008,
             <http://www.rfc-editor.org/info/rfc5332>.
 [RFC6074]   Rosen, E., Davie, B., Radoaca, V., and W. Luo,
             "Provisioning, Auto-Discovery, and Signaling in Layer 2
             Virtual Private Networks (L2VPNs)", RFC 6074,
             DOI 10.17487/RFC6074, January 2011,
             <http://www.rfc-editor.org/info/rfc6074>.
 [RFC6368]   Marques, P., Raszuk, R., Patel, K., Kumaki, K., and T.
             Yamagata, "Internal BGP as the Provider/Customer Edge
             Protocol for BGP/MPLS IP Virtual Private Networks
             (VPNs)", RFC 6368, DOI 10.17487/RFC6368, September 2011,
             <http://www.rfc-editor.org/info/rfc6368>.
 [RFC6388]   Wijnands, IJ., Ed., Minei, I., Ed., Kompella, K., and B.
             Thomas, "Label Distribution Protocol Extensions for
             Point-to-Multipoint and Multipoint-to-Multipoint Label
             Switched Paths", RFC 6388, DOI 10.17487/RFC6388, November
             2011, <http://www.rfc-editor.org/info/rfc6388>.
 [RFC6513]   Rosen, E., Ed., and R. Aggarwal, Ed., "Multicast in
             MPLS/BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513,
             February 2012, <http://www.rfc-editor.org/info/rfc6513>.
 [RFC6514]   Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
             Encodings and Procedures for Multicast in MPLS/BGP IP
             VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
             <http://www.rfc-editor.org/info/rfc6514>.

Rekhter, et al. Standards Track [Page 40] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

 [RFC6625]   Rosen, E., Ed., Rekhter, Y., Ed., Hendrickx, W., and R.
             Qiu, "Wildcards in Multicast VPN Auto-Discovery Routes",
             RFC 6625, DOI 10.17487/RFC6625, May 2012,
             <http://www.rfc-editor.org/info/rfc6625>.
 [RFC7117]   Aggarwal, R., Ed., Kamite, Y., Fang, L., Rekhter, Y., and
             C. Kodeboniya, "Multicast in Virtual Private LAN Service
             (VPLS)", RFC 7117, DOI 10.17487/RFC7117, February 2014,
             <http://www.rfc-editor.org/info/rfc7117>.
 [RFC7385]   Andersson, L. and G. Swallow, "IANA Registry for
             P-Multicast Service Interface (PMSI) Tunnel Type Code
             Points", RFC 7385, DOI 10.17487/RFC7385, October 2014,
             <http://www.rfc-editor.org/info/rfc7385>.

17.2. Informative References

 [GTM]       Zhang, J, Giuliano, L, Rosen, E., Ed., Subramanian, K.,
             Pacella, D., and J. Schiller, "Global Table Multicast
             with BGP-MVPN Procedures", Work in Progress, draft-ietf-
             bess-mvpn-global-table-mcast-00, November 2014.
 [RFC5920]   Fang, L., Ed., "Security Framework for MPLS and GMPLS
             Networks", RFC 5920, DOI 10.17487/RFC5920, July 2010,
             <http://www.rfc-editor.org/info/rfc5920>.
 [RFC7024]   Jeng, H., Uttaro, J., Jalil, L., Decraene, B., Rekhter,
             Y., and R. Aggarwal, "Virtual Hub-and-Spoke in BGP/MPLS
             VPNs", RFC 7024, DOI 10.17487/RFC7024, October 2013,
             <http://www.rfc-editor.org/info/rfc7024>.
 [SEAMLESS-MPLS]
             Leymann, N., Ed., Decraene, B., Filsfils, C.,
             Konstantynowicz, M., Ed., and D. Steinberg, "Seamless
             MPLS Architecture", Work in Progress,
             draft-ietf-mpls-seamless-mpls-07, June 2014.

Acknowledgements

 We would like to thank Loa Andersson and Qin Wu for their review and
 comments.

Rekhter, et al. Standards Track [Page 41] RFC 7524 Inter-Area P2MP Segmented LSPs May 2015

Authors' Addresses

 Yakov Rekhter
 Juniper Networks
 1194 North Mathilda Ave.
 Sunnyvale, CA 94089
 United States
 Eric C Rosen
 Juniper Networks
 10 Technology Park Drive
 Westford, MA 01886
 United States
 EMail: erosen@juniper.net
 Rahul Aggarwal
 EMail: raggarwa_1@yahoo.com
 Thomas Morin
 Orange
 2, avenue Pierre-Marzin
 22307 Lannion Cedex
 France
 EMail: thomas.morin@orange.com
 Irene Grosclaude
 Orange
 2, avenue Pierre-Marzin
 22307 Lannion Cedex
 France
 EMail: irene.grosclaude@orange.com
 Nicolai Leymann
 Deutsche Telekom AG
 Winterfeldtstrasse 21
 Berlin 10781
 Germany
 EMail: n.leymann@telekom.de
 Samir Saad
 AT&T
 EMail: samirsaad1@outlook.com

Rekhter, et al. Standards Track [Page 42]

/data/webs/external/dokuwiki/data/pages/rfc/rfc7524.txt · Last modified: 2015/05/13 22:44 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki