GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc7453

Internet Engineering Task Force (IETF) M. Venkatesan Request for Comments: 7453 Dell Inc. Category: Standards Track K. Sampath ISSN: 2070-1721 Redeem

                                                             S. Aldrin
                                                   Huawei Technologies
                                                             T. Nadeau
                                                               Brocade
                                                         February 2015
     MPLS Transport Profile (MPLS-TP) Traffic Engineering (TE)
                 Management Information Base (MIB)

Abstract

 This memo defines a portion of the Management Information Base (MIB)
 for use with network management protocols in the Internet community.
 In particular, it describes additional managed objects and textual
 conventions for tunnels, identifiers, and Label Switching Routers to
 support Multiprotocol Label Switching (MPLS) MIB modules for
 transport networks.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 5741.
 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc7453.

Venkatesan, et al. Standards Track [Page 1] RFC 7453 MPLS-TP MIB February 2015

Copyright Notice

 Copyright (c) 2015 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.

Table of Contents

 1. Introduction ....................................................4
 2. The Internet-Standard Management Framework ......................5
 3. Overview ........................................................5
    3.1. Conventions Used in This Document ..........................5
    3.2. Terminology ................................................6
    3.3. Acronyms ...................................................6
 4. Motivations .....................................................6
 5. Feature List ....................................................7
 6. Outline .........................................................7
    6.1. MIB Module Extensions ......................................8
         6.1.1. Summary of MIB Module Changes .......................8
    6.2. MPLS-TE-EXT-STD-MIB ........................................9
         6.2.1. mplsTunnelExtNodeConfigTable ........................9
         6.2.2. mplsTunnelExtNodeIpMapTable .........................9
         6.2.3. mplsTunnelExtNodeIccMapTable .......................10
         6.2.4. mplsTunnelExtTable .................................10
    6.3. MPLS-TC-EXT-STD-MIB .......................................10
    6.4. MPLS-ID-STD-MIB ...........................................10
    6.5. MPLS-LSR-EXT-STD-MIB ......................................11
    6.6. The Use of RowPointer .....................................11
 7. MIB Modules' Interdependencies .................................11
 8. Dependencies between MIB Module Tables .........................13
 9. Example of MPLS-TP Tunnel Setup ................................13
    9.1. Example of MPLS-TP Static Co-routed Bidirectional
         Tunnel Setup ..............................................15
         9.1.1. mplsTunnelEntry ....................................15
         9.1.2. mplsTunnelExtEntry .................................16
         9.1.3. Forward-Direction mplsOutSegmentEntry ..............16
         9.1.4. Reverse-Direction mplsInSegmentEntry ...............16
         9.1.5. Forward-Direction mplsXCEntry ......................17
         9.1.6. Reverse-Direction mplsXCEntry ......................17

Venkatesan, et al. Standards Track [Page 2] RFC 7453 MPLS-TP MIB February 2015

         9.1.7. Forward-Direction mplsXCExtEntry ...................18
         9.1.8. Reverse-Direction mplsXCExtEntry ...................18
    9.2. Example of MPLS-TP Static Associated Bidirectional
         Tunnel Setup ..............................................18
         9.2.1. Forward-Direction mplsTunnelEntry ..................18
         9.2.2. Forward-Direction mplsTunnelExtEntry ...............19
         9.2.3. Forward-Direction mplsOutSegmentTable ..............20
         9.2.4. Forward-Direction mplsXCEntry ......................20
         9.2.5. Forward-Direction mplsXCExtEntry ...................20
         9.2.6. Reverse-Direction mplsTunnelEntry ..................21
         9.2.7. Reverse-Direction mplsTunnelExtEntry ...............22
         9.2.8. Reverse-Direction mplsInSegmentEntry ...............22
         9.2.9. Reverse-Direction mplsXCEntry ......................22
         9.2.10. Reverse-Direction mplsXCExtEntry ..................23
    9.3. Example of MPLS-TP Signaled Co-routed
         Bidirectional Tunnel Setup ................................23
         9.3.1. mplsTunnelEntry ....................................23
         9.3.2. mplsTunnelExtEntry .................................24
         9.3.3. Forward-Direction mplsOutSegmentEntry ..............24
         9.3.4. Reverse-Direction mplsInSegmentEntry ...............25
         9.3.5. Forward-Direction mplsXCEntry ......................25
         9.3.6. Reverse-Direction mplsXCEntry ......................25
         9.3.7. Forward-Direction mplsXCExtEntry ...................25
         9.3.8. Reverse-Direction mplsXCExtEntry ...................25
 10. MPLS Textual Convention Extension MIB Definitions .............26
 11. MPLS Identifier MIB Definitions ...............................29
 12. MPLS LSR Extension MIB Definitions ............................34
 13. MPLS Tunnel Extension MIB Definitions .........................39
 14. Security Considerations .......................................57
 15. IANA Considerations ...........................................58
    15.1. IANA Considerations for MPLS-TC-EXT-STD-MIB ..............58
    15.2. IANA Considerations for MPLS-ID-STD-MIB ..................58
    15.3. IANA Considerations for MPLS-LSR-EXT-STD-MIB .............58
    15.4. IANA Considerations for MPLS-TE-EXT-STD-MIB ..............59
 16. References ....................................................59
    16.1. Normative References .....................................59
    16.2. Informative References ...................................60
 Acknowledgments ...................................................62
 Authors' Addresses ................................................62

Venkatesan, et al. Standards Track [Page 3] RFC 7453 MPLS-TP MIB February 2015

1. Introduction

 This memo defines a portion of the Management Information Base (MIB)
 for use with network management protocols in the Internet community.
 In particular, it describes additional textual conventions and
 managed objects for tunnels, identifiers, and Label Switching Routers
 to support Multiprotocol Label Switching (MPLS) MIB modules for
 transport networks.  MIB modules defined in this document extend the
 existing MPLS MIB objects in such a way that they support the MPLS
 Transport Profile (MPLS-TP) but also other MPLS networks.  Hence,
 "MPLS-TP" is not included in the MIB module names.
 As described in the MPLS Traffic Engineering (TE) MIB definition
 [RFC3812], MPLS traffic engineering is concerned with the creation
 and management of MPLS tunnels.  This term is a shorthand for a
 combination of one or more LSPs linking an ingress and an egress LSR.
 Several types of point-to-point MPLS tunnels may be constructed
 between a pair of LSRs A and B:
  1. Unidirectional with a single LSP (say, from A to B).
  1. Associated bidirectional consisting of two separately routed

LSPs, one linking A to B and the other linking B to A.

      Together, the pair provides a single logical bidirectional
      transport path.
  1. Co-routed bidirectional consisting of an associated

bidirectional tunnel but with the second LSP from B to A

      following the reverse of the path of the LSP from A to B, in
      terms of both nodes and links.
 Tunnels may be either statically configured by management action or
 dynamically created using an LSP management protocol.
 The existing MPLS TE MIB [RFC3812] and the GMPLS TE MIB [RFC4802]
 address only a subset of the combinations of statically and
 dynamically configured tunnel types, catering to statically
 configured unidirectional tunnels together with dynamically
 configured unidirectional and co-routed bidirectional tunnels.  They
 are also restricted to two endpoint LSRs identified by IP addresses.
 The MPLS-TP TE MIB defined in this document extends the MIB modules
 defined in [RFC3812] to cover all six combinations (that is, adding
 support for statically configured associated and co-routed
 bidirectional plus dynamically configured associated bidirectional
 tunnels).  It also extends support to endpoints that have identifiers
 other than IP addresses.

Venkatesan, et al. Standards Track [Page 4] RFC 7453 MPLS-TP MIB February 2015

 This support is provided by a suite of four MIB modules that are to
 be used in conjunction with the MIB modules defined in [RFC3812] and
 the companion document [RFC3813] for MPLS-TP tunnel management.
 At the time of writing, SNMP SET is no longer recommended as a way to
 configure MPLS networks as described in [RFC3812].  However, since
 the MIB modules specified in this document extend and are intended to
 work in parallel with the MIB modules for MPLS specified in
 [RFC3812], certain objects defined here are specified with MAX-ACCESS
 of read-write or read-create so that specifications of the base
 tables in [RFC3812] and the extensions in this document are
 consistent.  Although the examples described in Section 9 specify
 means to configure MPLS-TP Tunnels in a similar way to the examples
 in [RFC3812], this should be seen as indicating how the MIB values
 would be returned if the specified circumstances were configured by
 alternative means.

2. The Internet-Standard Management Framework

 For a detailed overview of the documents that describe the current
 Internet-Standard Management Framework, please refer to section 7 of
 RFC 3410 [RFC3410].
 Managed objects are accessed via a virtual information store, termed
 the Management Information Base or MIB.  MIB objects are generally
 accessed through the Simple Network Management Protocol (SNMP).
 Objects in the MIB are defined using the mechanisms defined in the
 Structure of Management Information (SMI).  This memo specifies a MIB
 module that is compliant to the SMIv2, which is described in STD 58,
 RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
 [RFC2580].

3. Overview

3.1. Conventions Used in This Document

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
 "OPTIONAL" in this document are to be interpreted as described in
 [RFC2119].

Venkatesan, et al. Standards Track [Page 5] RFC 7453 MPLS-TP MIB February 2015

3.2. Terminology

 This document uses terminology from the "Multiprotocol Label
 Switching Architecture" [RFC3031], "Multiprotocol Label Switching
 (MPLS) Traffic Engineering (TE) Management Information Base (MIB)"
 [RFC3812], "Multiprotocol Label Switching (MPLS) Label Switching
 Router (LSR) Management Information Base (MIB)" [RFC3813], and"MPLS
 Transport Profile (MPLS-TP) Identifiers" [RFC6370].

3.3. Acronyms

 CC: Country Code
 ICC: ITU Carrier Code
 LSP: Label Switched Path
 LSR: Label Switching Router
 MPLS-TP: MPLS Transport Profile
 TE: Traffic Engineering
 TP: Transport Profile

4. Motivations

 "Multiprotocol Label Switching (MPLS) Traffic Engineering (TE)
 Management Information Base (MIB)" [RFC3812] provides support for
 Traffic Engineering tunnels.  In MPLS, the actual transport of
 packets is provided by Label Switched Paths (LSPs).  A transport
 service may be composed of multiple LSPs.  In order to clearly
 identify the MPLS-TP service, as defined in [RFC6370], we use the
 term "MPLS-TP Tunnel" or simply "tunnel".  However, with MPLS-TP, the
 characteristics of the tunnels were enhanced.  For example, MPLS-TP
 Tunnels are bidirectional in nature and could be used with non-IP
 identifiers for the tunnel endpoints.  As the existing
 MPLS-TE-STD-MIB and GMPLS-TE-STD-MIB were defined mainly to support
 unidirectional tunnels and signaled co-routed bidirectional tunnel
 definitions, respectively, these existing MIB modules are not
 sufficient to capture all the characteristics of the tunnels.  Hence,
 enhancing the MIB modules to support MPLS-TP Tunnels is required.  As
 most of the attributes of MPLS Traffic Engineering tunnels are also
 applicable to MPLS-TP Tunnels, it is optimal to reuse and extend the
 existing MIB module definition instead of defining a new MIB module.
 This document defines four additional MIB modules, namely,
 MPLS-TE-EXT-STD-MIB, MPLS-TC-EXT-STD-MIB, MPLS-ID-STD-MIB, and
 MPLS-LSR-EXT-STD-MIB.  As these additional MIB modules are required
 for MPLS-TP functionality, these are all defined in this document,
 instead of being documented separately.

Venkatesan, et al. Standards Track [Page 6] RFC 7453 MPLS-TP MIB February 2015

5. Feature List

 The MIBs in this document satisfy the following requirements and
 constraints:
 The MIB modules, taken together, support statically configured and
 dynamically signaled point-to-point, co-routed bidirectional and
 associated bidirectional tunnels.
  1. The MPLS tunnels need not be interfaces, but it is possible to

configure an MPLS-TP Tunnel as an interface. The same ifType

      150, as defined in Section 8 of [RFC3812], will be used for
      MPLS-TP Tunnels as well.
  1. The mplsTunnelTable [RFC3812] is also to be used for MPLS-TP

Tunnels.

  1. New MPLS-TP-specific textual conventions and identifiers are

required.

  1. The mplsTunnelTable is sparsely extended to support objects

specific to MPLS-TP Tunnels.

  1. A node configuration table (mplsTunnelExtNodeConfigTable), as

detailed in Section 6.2.1, below, is used to translate the

      Global_ID::Node_ID or ICC_Operator_ID::Node_ID to the local
      identifier in order to index the mplsTunnelTable.
  1. The mplsXCTable is sparsely extended to support objects specific

to MPLS-TP XC (Cross Connect).

  1. The MIB module supports persistent, as well as non-persistent,

tunnels.

6. Outline

 Traffic Engineering support for the MPLS-TP Tunnels requires the
 setup of the co-routed or associated bidirectional tunnel.  The
 tables and MIB modules that are mentioned in the below subsections
 support the functionality described in [RFC5654] and [RFC6370].
 These tables support both IP-compatible and ICC-based tunnel
 configurations.
 Figure 1, below, depicts how the table references are followed in
 this MIB.

Venkatesan, et al. Standards Track [Page 7] RFC 7453 MPLS-TP MIB February 2015

          Tunnel1-->XC1<--------------
           ^ ^      | |               |
           | |      | |-->InSeg1      |
           | |      | |-->OutSeg1     |
           | |      v                 |
           |  ------XCext1            |
           |         |                |
           V         v                |
          Tunnel2-->XC1               |
             ^      | |               |
             |      | |-->InSeg2      |
             |      | |-->OutSeg2     |
             |      v                 |
              ------XCext2------------
               Figure 1: Table References of MIB Modules

6.1. MIB Module Extensions

 Four MIB modules are extended to support MPLS-TP Tunnels, namely,
 MPLS-TE-EXT-STD-MIB, MPLS-TC-EXT-STD-MIB, MPLS-ID-STD-MIB, and
 MPLS-LSR-EXT-STD-MIB.  The following section provides the summary of
 changes.

6.1.1. Summary of MIB Module Changes

  1. Node configuration table (mplsTunnelExtNodeConfigTable) for setting

the local identifier for Tunnel Ingress and Egress identifiers.

  1. Node IP map table (mplsTunnelExtNodeIpMapTable) for querying the

local identifier for a given Global_ID and Node_ID.

  1. Node ICC map table (mplsTunnelExtNodeIccMapTable) for querying the

local identifier for a given ICC_Operator_ID and Node_ID.

  1. Tunnel extension table (mplsTunnelExtTable) for setting up MPLS-TP

Tunnels with sparse extension of mplsTunnelTable.

  1. Textual conventions and object definitions for MPLS-TP Tunnels.
  1. Cross-connect extension table (mplsXCExtTable) for setting up the

MPLS-TP LSPs.

   These tables are described in the subsequent sections.

Venkatesan, et al. Standards Track [Page 8] RFC 7453 MPLS-TP MIB February 2015

6.2. MPLS-TE-EXT-STD-MIB

   The TE MIB module extensions and details of the tables are
   described in the following sections.

6.2.1. mplsTunnelExtNodeConfigTable

 The mplsTunnelExtNodeConfigTable is used to assign a local identifier
 for a given ICC_Operator_ID::Node_ID or Global_ID::Node_ID
 combination as defined in [RFC6923] and [RFC6370], respectively.  The
 CC is a string of two characters, each being an uppercase Basic Latin
 alphabetic (i.e., A-Z).  The ICC is a string of one to six
 characters, each an uppercase Basic Latin alphabetic (i.e., A-Z) or
 numeric (i.e., 0-9).  All of the characters are encoded using [T.50]
 as described in [RFC6370].
 In the IP-compatible mode, Global_ID::Node_ID, is used to uniquely
 identify a node.  For each ICC_Operator_ID::Node_ID or
 Global_ID::Node_ID, there is a unique entry in the table representing
 a node.  As the regular TE tunnels use the IP address as the LSR ID,
 the local identifier should be below the first valid IP address,
 which is 16777216[1.0.0.0].  Every node is assigned a local
 identifier within a range of 0 to 16777215.  This local identifier is
 used for indexing into mplsTunnelTable as mplsTunnelIngressLSRId and
 mplsTunnelEgressLSRId.
 For IP-compatible environments, an MPLS-TP Tunnel is indexed by
 Tunnel Index, Tunnel Instance, Source Global_ID, Source Node_ID,
 Destination Global_ID, and Destination Node_ID.
 For ICC-based environments, an MPLS-TP Tunnel is indexed by Tunnel
 Index, Tunnel Instance, Source CC, Source ICC, Source Node_ID,
 Destination CC, Destination ICC, and Destination Node_ID.
 As mplsTunnelTable is indexed by mplsTunnelIndex, mplsTunnelInstance,
 mplsTunnelIngressLSRId, and mplsTunnelEgressLSRId, the MPLS-TP tunnel
 identifiers cannot be used directly.
 The mplsTunnelExtNodeConfigTable will be used to store an entry for
 ICC_Operator_ID::Node_ID or Global_ID::Node_ID with a local
 identifier to be used as the LSR ID in mplsTunnelTable.

6.2.2. mplsTunnelExtNodeIpMapTable

 The read-only mplsTunnelExtNodeIpMapTable is used to query the local
 identifier assigned and stored in mplsTunnelExtNodeConfigTable for a
 given Global_ID::Node_ID.  In order to query the local identifier, in

Venkatesan, et al. Standards Track [Page 9] RFC 7453 MPLS-TP MIB February 2015

 the IP-compatible mode, this table is indexed with
 Global_ID::Node_ID.  In the IP-compatible mode for a TP tunnel,
 Global_ID::Node_ID is used.
 A separate query is made to get the local identifier of both Ingress
 and Egress Global_ID::Node_ID identifiers.  These local identifiers
 are used as mplsTunnelIngressLSRId and mplsTunnelEgressLSRId when
 indexing mplsTunnelTable.

6.2.3. mplsTunnelExtNodeIccMapTable

 The read-only mplsTunnelExtNodeIccMapTable is used to query the local
 identifier assigned and stored in the mplsTunnelExtNodeConfigTable
 for a given ICC_Operator_ID::Node_ID.
 A separate query is made to get the local identifier of both Ingress
 and Egress ICC_Operator_ID::Node_ID.  These local identifiers are
 used as mplsTunnelIngressLSRId and mplsTunnelEgressLSRId when
 indexing mplsTunnelTable.

6.2.4. mplsTunnelExtTable

 This table sparsely extends the mplsTunnelTable in order to support
 MPLS-TP Tunnels with additional objects.  All the additional
 attributes specific to supporting a TP tunnel are contained in this
 extended table and could be accessed with the mplsTunnelTable
 indices.
 The gmplsTunnelReversePerfTable [RFC4802] should be used to provide
 per-tunnel packet performance information for the reverse direction
 of a bidirectional tunnel.  It can be seen as supplementing the
 mplsTunnelPerfTable, which augments the mplsTunnelTable.

6.3. MPLS-TC-EXT-STD-MIB

 This MIB module contains textual conventions for LSPs of MPLS-based
 transport networks.

6.4. MPLS-ID-STD-MIB

 This MIB module contains identifier object definitions for MPLS
 Traffic Engineering in transport networks.

Venkatesan, et al. Standards Track [Page 10] RFC 7453 MPLS-TP MIB February 2015

6.5. MPLS-LSR-EXT-STD-MIB

 This MIB module contains generic object definitions (including the
 mplsXCExtTable -- cross-connect extension table -- for setting up the
 MPLS-TP LSPs with sparse extension of mplsXCTable) for MPLS LSRs in
 transport networks.

6.6. The Use of RowPointer

 This document follows the RowPointer usage as described in Section 10
 of [RFC3812].
 A new RowPointer object, mplsTunnelExtOppositeDirPtr, is added to
 mplsTunnelExtTable of MPLS-TE-EXT-STD-MIB module.  This RowPointer
 object points to the tunnel entry in the opposite direction.
 Two additional RowPointers objects, mplsXCExtTunnelPointer and
 mplsXCExtOppositeDirXCPtr, are added to the mplsXCExtTable of
 MPLS-LSR-EXT-STD-MIB.  The RowPointer mplsXCExtTunnelPointer is a
 read-only object used to indicate the back pointer to the tunnel
 entry.  The RowPointer mplsXCExtOppositeDirXCPtr object points to the
 opposite-direction XC entry.
 If either of these RowPointers return zeroDotZero, it implies that
 there is no entry associated with the RowPointer object.

7. MIB Modules' Interdependencies

 This section provides an overview of the relationships between the
 MPLS-TP TE MIB module and other MPLS MIB modules.
 The arrows in the following diagram show a "depends on" relationship.
 A relationship of "MIB module A depends on MIB module B" means that
 MIB module A uses an object, object identifier, or textual convention
 defined in MIB module B, or that MIB module A contains a pointer
 (index or RowPointer) to an object in MIB module B.

Venkatesan, et al. Standards Track [Page 11] RFC 7453 MPLS-TP MIB February 2015

     MPLS-TC-EXT-STD-MIB
        ^
        |
        |
        +<---- MPLS-ID-STD-MIB
                      ^
        |             |
        +<---- MPLS-TE-EXT-STD-MIB
        |             |
        |             V
        |      MPLS-TE-STD-MIB
        |             |
        |             |
        |             V
        |      MPLS-LSR-STD-MIB
        |             ^
        |             |
        |             |
        +------MPLS-LSR-EXT-STD-MIB
     Figure 2: MIB Modules' Interdependencies
     Thus:
  1. All the new MPLS extension MIB modules depend on

MPLS-TC-EXT-STD-MIB.

  1. MPLS-ID-STD-MIB contains references to objects in

MPLS-TE-STD-MIB [RFC3812].

  1. MPLS-TE-EXT-STD-MIB contains references to objects in

MPLS-TE-STD-MIB [RFC3812].

  1. MPLS-LSR-EXT-STD-MIB contains references to objects in

MPLS-LSR-STD-MIB [RFC3813].

 The mplsTunnelExtTable sparsely extends the mplsTunnelTable of
 MPLS-TE-STD-MIB [RFC3812].  This helps in associating the reverse-
 direction tunnel information.
 The mplsXCExtTable sparsely extends the mplsXCTable of
 MPLS-LSR-STD-MIB [RFC3813].  This helps in pointing back to the
 tunnel entry for easy tunnel access from the XC entry.
 Note that all of the MIB modules shown above in the figure also have
 a dependency on MPLS-TC-STD-MIB.

Venkatesan, et al. Standards Track [Page 12] RFC 7453 MPLS-TP MIB February 2015

8. Dependencies between MIB Module Tables

 The tables in MPLS-TE-EXT-STD-MIB are related as shown on the diagram
 below.  The arrows indicate a reference from one table to another.
       mplsTunnelExtNodeConfigTable
            ^          ^       ^
            |          |       |
            |          |       |
            |          |       |
            |          |       +----------------------+
            |          |                              |
            | mplsTunnelExtNodeIpMapTable mplsTunnelExtNodeIccMapTable
            |
            |              mplsXCExtTable
            |               |      ^
            |     +---------+      |
            |     |                |
            |     |                |
            |     V                V
       mplsTunnelTable ---->mplsXCTable
            ^
            |
            |
            |
      mplsTunnelExtTable
   Figure 3: Dependencies between MIB Module Tables
 An existing mplsTunnelTable uses the mplsTunnelExtNodeConfigTable
 table to map the Global_ID::Node_ID and/or ICC_Operator_ID::Node_ID
 with the local number in order to accommodate in the existing tunnel
 table's ingress/egress LSR ID.
 The new mplsTunnelExtTable provides the reverse-direction LSP
 information for the existing tunnel table so that bidirectional LSPs
 can be created.
 The mplsXCExtTable sparsely extends the mplsLsrXCTable to provide
 backward reference to tunnel entry.

9. Example of MPLS-TP Tunnel Setup

 In this section, we provide an example of configuring MPLS-TP
 bidirectional tunnels with IP tunnel identifiers.  This example
 provides the usage of the MPLS-TP Tunnel MIB along with the extended
 MIB modules introduced in this document.

Venkatesan, et al. Standards Track [Page 13] RFC 7453 MPLS-TP MIB February 2015

 Do note that a MPLS-TP Tunnel could be set up statically as well as
 signaled via the control plane.  This example considers accessing MIB
 objects on a head-end for static and signaled MPLS-TP Tunnels.  This
 section shows the configuration of the forward- and reverse-direction
 MPLS-TP LSPs that run between East and West, and vice versa.  Only
 objects relevant to MPLS-TP Tunnels are illustrated here.
 In mplsTunnelExtNodeConfigTable:
 {
 -- Non-IP Ingress LSR_ID (Index to the table)
   mplsTunnelExtNodeConfigLocalId              = 1,
   mplsTunnelExtNodeConfigGlobalId             = 1234,
   mplsTunnelExtNodeConfigNodeId               = 10,
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelExtNodeConfigRowStatus         = createAndGo (4)
  1. - Non-IP Egress LSR ID (Index to the table)

mplsTunnelExtNodeConfigLocalId = 2,

   mplsTunnelExtNodeConfigGlobalId             = 1234,
   mplsTunnelExtNodeConfigNodeId               = 20,
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelExtNodeConfigRowStatus         = createAndGo (4)
 }
 This will create an entry in the mplsTunnelExtNodeConfigTable for a
 Global_ID::Node_ID.  The Ingress and Egress LSR are represented by
 separate entries.
 The following read-only mplsTunnelExtNodeIpMapTable table is
 populated automatically upon creating an entry in
 mplsTunnelExtNodeConfigTable, and this table is used to retrieve the
 local identifier for the given Global_ID::Node_ID.
 In mplsTunnelExtNodeIpMapTable:
 {
 -- Global_ID (Index to the table)
   mplsTunnelExtNodeIpMapGlobalId             = 1234,
 -- Node Identifier (Index to the table)
   mplsTunnelExtNodeIpMapNodeId               = 10,
   mplsTunnelExtNodeIpMapLocalId              = 1
  1. - Global_ID (Index to the table)

mplsTunnelExtNodeIpMapGlobalId = 1234,

Venkatesan, et al. Standards Track [Page 14] RFC 7453 MPLS-TP MIB February 2015

  1. - Node Identifier (Index to the table)

mplsTunnelExtNodeIpMapNodeId = 20,

   mplsTunnelExtNodeIpMapLocalId              = 2
 }

9.1. Example of MPLS-TP Static Co-routed Bidirectional Tunnel Setup

 The following denotes the co-routed bidirectional tunnel "head"
 entry.

9.1.1. mplsTunnelEntry

   In mplsTunnelTable:
 {
   mplsTunnelIndex              = 1,
   mplsTunnelInstance           = 1,
 -- Local map number created in mplsTunnelExtNodeConfigTable for
 -- Ingress LSR ID
   mplsTunnelIngressLSRId       = 1,
  1. - Local map number created in mplsTunnelExtNodeConfigTable for
  2. - Egress LSR ID

mplsTunnelEgressLSRId = 2,

   mplsTunnelName               = "TP co-routed bidirectional LSP",
   mplsTunnelDescr              = "East to West",
   mplsTunnelIsIf               = true (1),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelXCPointer          =
                              mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
   mplsTunnelSignallingProto    = none (1),
   mplsTunnelSetupPrio          = 0,
   mplsTunnelHoldingPrio        = 0,
   mplsTunnelSessionAttributes  = 0,
   mplsTunnelLocalProtectInUse  = false (0),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelResourcePointer    = mplsTunnelResourceMaxRate.5,
   mplsTunnelInstancePriority   = 1,
   mplsTunnelHopTableIndex      = 1,
   mplsTunnelIncludeAnyAffinity = 0,
   mplsTunnelIncludeAllAffinity = 0,
   mplsTunnelExcludeAnyAffinity = 0,
   mplsTunnelRole               = head (1),
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelRowStatus          = createAndGo (4)
 }

Venkatesan, et al. Standards Track [Page 15] RFC 7453 MPLS-TP MIB February 2015

9.1.2. mplsTunnelExtEntry

  1. - An MPLS extension table

In mplsTunnelExtTable:

 {
   -- This opposite-direction tunnel pointer may point to 0.0
   -- if co-routed bidirectional tunnel is managed by single tunnel
   -- entry
   mplsTunnelExtOppositeDirTnlPtr       = 0.0
   -- Set both the Ingress and Egress LocalId objects to TRUE, as
   -- this tunnel entry uses the local identifiers.
   mplsTunnelExtIngressLSRLocalIdValid  = true,
   mplsTunnelExtEgressLSRLocalIdValid = true
 }
 Next, we must create the appropriate in-segment and out-segment
 entries.  These are done in [RFC3813] using the mplsInSegmentTable
 and mplsOutSegmentTable.

9.1.3. Forward-Direction mplsOutSegmentEntry

 For the forward direction:
 In mplsOutSegmentTable:
 {
    mplsOutSegmentIndex          = 0x0000001,
    mplsOutSegmentInterface      = 13, -- outgoing interface
    mplsOutSegmentPushTopLabel   = true(1),
    mplsOutSegmentTopLabel       = 22, -- outgoing label
  1. - RowPointer MUST point to the first accessible column.

mplsOutSegmentTrafficParamPtr = 0.0,

    mplsOutSegmentRowStatus         = createAndGo (4)
 }

9.1.4. Reverse-Direction mplsInSegmentEntry

   For the reverse direction:
 In mplsInSegmentTable:
 {
    mplsInSegmentIndex           = 0x0000001
    mplsInSegmentLabel           = 21, -- incoming label
    mplsInSegmentNPop            = 1,
    mplsInSegmentInterface       = 13, -- incoming interface

Venkatesan, et al. Standards Track [Page 16] RFC 7453 MPLS-TP MIB February 2015

  1. - RowPointer MUST point to the first accessible column.

mplsInSegmentTrafficParamPtr = 0.0,

    mplsInSegmentRowStatus          = createAndGo (4)
 }
 Next, two cross-connect entries are created in the mplsXCTable of the
 MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
 segments together.

9.1.5. Forward-Direction mplsXCEntry

 In mplsXCTable:
 {
    mplsXCIndex                = 0x01,
    mplsXCInSegmentIndex       = 0x00000000,
    mplsXCOutSegmentIndex      = 0x00000001,
    mplsXCLspId                = 0x0102 -- unique ID
  1. - only a single outgoing label

mplsXCLabelStackIndex = 0x00,

    mplsXCRowStatus            = createAndGo(4)
 }

9.1.6. Reverse-Direction mplsXCEntry

 In mplsXCTable:
 {
    mplsXCIndex                = 0x01,
    mplsXCInSegmentIndex       = 0x00000001,
    mplsXCOutSegmentIndex      = 0x00000000,
    mplsXCLspId                = 0x0102 -- unique ID
    -- only a single outgoing label
    mplsXCLabelStackIndex      = 0x00,
    mplsXCRowStatus            = createAndGo(4)
 }
 This table entry is extended by an entry in the mplsXCExtTable.  Note
 that the nature of the 'extends' relationship is a sparse
 augmentation so that the entry in the mplsXCExtTable has the same
 index values as the entry in the mplsXCTable.

Venkatesan, et al. Standards Track [Page 17] RFC 7453 MPLS-TP MIB February 2015

9.1.7. Forward-Direction mplsXCExtEntry

 In mplsXCExtTable (0x01, 0x00000000, 0x00000001)
 {
   -- Back pointer from XC table to Tunnel table
   mplsXCExtTunnelPointer         = mplsTunnelName.1.1.1.2
   mplsXCExtOppositeDirXCPtr         =
                               mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0
 }

9.1.8. Reverse-Direction mplsXCExtEntry

 Next, for the reverse direction:
 In mplsXCExtTable (0x01, 0x00000001, 0x00000000)
 {
   -- Back pointer from XC table to Tunnel table
   mplsXCExtTunnelPointer         = mplsTunnelName.1.1.1.2
   mplsXCExtOppositeDirXCPtr         =
                               mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1
 }

9.2. Example of MPLS-TP Static Associated Bidirectional Tunnel Setup

 The MPLS-TP associated bidirectional tunnel is implemented by two
 different unidirectional tunnels (Forward and Reverse LSPs), and
 these are associated together using mplsTunnelExtTable.  Two
 different tunnel entries to provide the forward and reverse
 directions MAY be used for co-routed bidirectional tunnels as well.
 The following denotes the associated bidirectional forward tunnel
 "head" entry:

9.2.1. Forward-Direction mplsTunnelEntry

   In mplsTunnelTable:
 {
   mplsTunnelIndex              = 1,
   mplsTunnelInstance           = 1,
 -- Local map number created in mplsTunnelExtNodeConfigTable for
 -- Ingress LSR ID
   mplsTunnelIngressLSRId       = 1,

Venkatesan, et al. Standards Track [Page 18] RFC 7453 MPLS-TP MIB February 2015

  1. - Local map number created in mplsTunnelExtNodeConfigTable for
  2. - Egress LSR ID

mplsTunnelEgressLSRId = 2,

   mplsTunnelName               = "TP associated bidirectional
                                   forward LSP",
   mplsTunnelDescr              = "East to West",
   mplsTunnelIsIf               = true (1),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelXCPointer          =
                              mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
   mplsTunnelSignallingProto    = none (1),
   mplsTunnelSetupPrio          = 0,
   mplsTunnelHoldingPrio        = 0,
   mplsTunnelSessionAttributes  = 0,
   mplsTunnelLocalProtectInUse  = false (0),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelResourcePointer    = mplsTunnelResourceMaxRate.5,
   mplsTunnelInstancePriority   = 1,
   mplsTunnelHopTableIndex      = 1,
   mplsTunnelIncludeAnyAffinity = 0,
   mplsTunnelIncludeAllAffinity = 0,
   mplsTunnelExcludeAnyAffinity = 0,
   mplsTunnelRole               = head (1),
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelRowStatus          = createAndGo (4)
 }

9.2.2. Forward-Direction mplsTunnelExtEntry

 For the associated bidirectional forward LSP,
 in mplsTunnelExtTable:
 {
   mplsTunnelExtOppositeDirPtr       = mplsTunnelName.2.1.2.1
  -- Set both the Ingress and Egress LocalId objects to TRUE, as
  -- this tunnel entry uses the local identifiers.
   mplsTunnelExtIngressLSRLocalIdValid  = true,
   mplsTunnelExtEgressLSRLocalIdValid = true
 }

Venkatesan, et al. Standards Track [Page 19] RFC 7453 MPLS-TP MIB February 2015

9.2.3. Forward-Direction mplsOutSegmentTable

 For the forward direction:
 In mplsOutSegmentTable:
 {
    mplsOutSegmentIndex          = 0x0000001,
    mplsOutSegmentInterface      = 13, -- outgoing interface
    mplsOutSegmentPushTopLabel   = true(1),
    mplsOutSegmentTopLabel       = 22, -- outgoing label
  1. - RowPointer MUST point to the first accessible column.

mplsOutSegmentTrafficParamPtr = 0.0,

    mplsOutSegmentRowStatus         = createAndGo (4)
 }

9.2.4. Forward-Direction mplsXCEntry

 In mplsXCTable:
 {
    mplsXCIndex                = 0x01,
    mplsXCInSegmentIndex       = 0x00000000,
    mplsXCOutSegmentIndex      = 0x00000001,
    mplsXCLspId                = 0x0102 -- unique ID
    -- only a single outgoing label
    mplsXCLabelStackIndex      = 0x00,
    mplsXCRowStatus            = createAndGo(4)
 }

9.2.5. Forward-Direction mplsXCExtEntry

 In mplsXCExtTable (0x01, 0x00000000, 0x00000001)
 {
   -- Back pointer from XC table to Tunnel table
   mplsXCExtTunnelPointer         = mplsTunnelName.1.1.1.2
   mplsXCExtOppositeDirXCPtr         =
                              mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0
 }

Venkatesan, et al. Standards Track [Page 20] RFC 7453 MPLS-TP MIB February 2015

9.2.6. Reverse-Direction mplsTunnelEntry

 The following denotes the configured associated bidirectional reverse
 tunnel "tail" entry:
     In mplsTunnelTable:
 {
   mplsTunnelIndex              = 2,
   mplsTunnelInstance           = 1,
 -- Local map number created in mplsTunnelExtNodeConfigTable for
 -- Ingress LSR ID
   mplsTunnelIngressLSRId       = 2,
 -- Local map number created in mplsTunnelExtNodeConfigTable for
 -- Egress LSR ID
   mplsTunnelEgressLSRId        = 1,
   mplsTunnelName               = "TP associated bidirectional
                                   reverse LSP",
   mplsTunnelDescr              = "West to East",
   mplsTunnelIsIf               = true (1),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelXCPointer          =
                              mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0,
   mplsTunnelSignallingProto    = none (1),
   mplsTunnelSetupPrio          = 0,
   mplsTunnelHoldingPrio        = 0,
   mplsTunnelSessionAttributes  = 0,
   mplsTunnelLocalProtectInUse  = false (0),
  1. - RowPointer MUST point to the first accessible column

mplsTunnelResourcePointer = mplsTunnelResourceMaxRate.5,

   mplsTunnelInstancePriority   = 1,
   mplsTunnelHopTableIndex      = 1,
   mplsTunnelIncludeAnyAffinity = 0,
   mplsTunnelIncludeAllAffinity = 0,
   mplsTunnelExcludeAnyAffinity = 0,
   mplsTunnelRole               = head (1),
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelRowStatus          = createAndGo (4)
 }

Venkatesan, et al. Standards Track [Page 21] RFC 7453 MPLS-TP MIB February 2015

9.2.7. Reverse-Direction mplsTunnelExtEntry

 For the associated bidirectional reverse LSP,
 in mplsTunnelExtTable:
 {
   mplsTunnelExtOppositeDirPtr       = mplsTunnelName.1.1.1.2
   -- Set both the Ingress and Egress LocalId objects to TRUE, as
   -- this tunnel entry uses the local identifiers.
   mplsTunnelExtIngressLSRLocalIdValid  = true,
   mplsTunnelExtEgressLSRLocalIdValid = true
 }

9.2.8. Reverse-Direction mplsInSegmentEntry

 Next, we must create the appropriate in-segment and out-segment
 entries.  These are done in [RFC3813] using the mplsInSegmentTable
 and mplsOutSegmentTable.
 In mplsInSegmentTable:
 {
    mplsInSegmentIndex           = 0x0000001
    mplsInSegmentLabel           = 21, -- incoming label
    mplsInSegmentNPop            = 1,
    mplsInSegmentInterface       = 13, -- incoming interface
  1. - RowPointer MUST point to the first accessible column.

mplsInSegmentTrafficParamPtr = 0.0,

    mplsInSegmentRowStatus          = createAndGo (4)
 }
 Next, two cross-connect entries are created in the mplsXCTable of the
 MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
 segments together.

9.2.9. Reverse-Direction mplsXCEntry

 In mplsXCTable:
 {
    mplsXCIndex                = 0x01,
    mplsXCInSegmentIndex       = 0x00000001,
    mplsXCOutSegmentIndex      = 0x00000000,
    mplsXCLspId                = 0x0102 -- unique ID
    -- only a single outgoing label
    mplsXCLabelStackIndex      = 0x00,
    mplsXCRowStatus            = createAndGo(4)
 }

Venkatesan, et al. Standards Track [Page 22] RFC 7453 MPLS-TP MIB February 2015

 This table entry is extended by an entry in the mplsXCExtTable.  Note
 that the nature of the 'extends' relationship is a sparse
 augmentation so that the entry in the mplsXCExtTable has the same
 index values as the entry in the mplsXCTable.

9.2.10. Reverse-Direction mplsXCExtEntry

 Next, for the reverse direction:
 In mplsXCExtTable (0x01, 0x00000001, 0x00000000)
 {
   -- Back pointer from XC table to Tunnel table
   mplsXCExtTunnelPointer         = mplsTunnelName.2.1.2.1
   mplsXCExtOppositeDirXCPtr         =
                            mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1
 }

9.3. Example of MPLS-TP Signaled Co-routed Bidirectional Tunnel Setup

 The following denotes the co-routed bidirectional tunnel "head"
 entry.  In intermediate and tail-end nodes, the tunnel table and its
 associated tables are created by the local management subsystem
 (e.g., agent) when the MPLS-TP Tunnel is signaled successfully.
 Refer to [RFC3812] and [RFC4802] for examples of signaled tunnel
 table configuration.

9.3.1. mplsTunnelEntry

   In mplsTunnelTable:
 {
   mplsTunnelIndex              = 1,
   mplsTunnelInstance           = 0,
 -- Local map number created in mplsTunnelExtNodeConfigTable for
 -- Ingress LSR-Id.  For the intermediate and tail-end nodes,
 -- the local management entity is expected to pick the first
 -- available local identifier that is not used in mplsTunnelTable.
   mplsTunnelIngressLSRId       = 1,
  1. - Local map number created in mplsTunnelExtNodeConfigTable for
  2. - Egress LSR ID

mplsTunnelEgressLSRId = 2,

   mplsTunnelName               = "TP co-routed bidirectional LSP",
   mplsTunnelDescr              = "East to West",
   mplsTunnelIsIf               = true (1),

Venkatesan, et al. Standards Track [Page 23] RFC 7453 MPLS-TP MIB February 2015

  1. - RowPointer MUST point to the first accessible column

mplsTunnelXCPointer =

                              mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
   mplsTunnelSignallingProto    = none (1),
   mplsTunnelSetupPrio          = 0,
   mplsTunnelHoldingPrio        = 0,
   mplsTunnelSessionAttributes  = 0,
   mplsTunnelLocalProtectInUse  = false (0),
 --  RowPointer MUST point to the first accessible column
   mplsTunnelResourcePointer    = mplsTunnelResourceMaxRate.5,
   mplsTunnelInstancePriority   = 1,
   mplsTunnelHopTableIndex      = 1,
   mplsTunnelIncludeAnyAffinity = 0,
   mplsTunnelIncludeAllAffinity = 0,
   mplsTunnelExcludeAnyAffinity = 0,
   mplsTunnelRole               = head (1),
 -- Mandatory parameters needed to activate the row go here
   mplsTunnelRowStatus          = createAndGo (4)
 }

9.3.2. mplsTunnelExtEntry

  1. - An MPLS extension table

In mplsTunnelExtTable:

 {
   -- This opposite-direction tunnel pointer may point to 0.0
   -- if co-routed bidirectional tunnel is managed by a single
   -- tunnel entry
   mplsTunnelExtOppositeDirTnlPtr       = 0.0
   -- Set both the Ingress and Egress LocalId objects to TRUE, as
   -- this tunnel entry uses the local identifiers.
   mplsTunnelExtIngressLSRLocalIdValid  = true,
   mplsTunnelExtEgressLSRLocalIdValid = true
 }
 Next, we must create the appropriate in-segment and out-segment
 entries.  These are done in [RFC3813] using the mplsInSegmentTable
 and mplsOutSegmentTable.

9.3.3. Forward-Direction mplsOutSegmentEntry

 The forward-direction mplsOutSegmentTable will be populated
 automatically based on the information received from the signaling
 protocol.

Venkatesan, et al. Standards Track [Page 24] RFC 7453 MPLS-TP MIB February 2015

9.3.4. Reverse-Direction mplsInSegmentEntry

 The reverse-direction mplsOutSegmentTable will be populated
 automatically based on the information received from the signaling
 protocol.
 Next, two cross-connect entries are created in the mplsXCTable of the
 MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
 segments together.

9.3.5. Forward-Direction mplsXCEntry

 The forward-direction mplsXCEntry will be populated as soon as the
 forward-path label information is available.

9.3.6. Reverse-Direction mplsXCEntry

 The reverse-direction mplsXCEntry will be populated as soon as the
 reverse-path label information is available.
 This table entry is extended by an entry in the mplsXCExtTable.  Note
 that the nature of the 'extends' relationship is a sparse
 augmentation so that the entry in the mplsXCExtTable has the same
 index values as the entry in the mplsXCTable.

9.3.7. Forward-Direction mplsXCExtEntry

 Once the forward path information is negotiated using the signaling
 protocol, the forward-direction mplsXCExtEntry will be created for
 associating the opposite-direction XC entry and tunnel table entry.

9.3.8. Reverse-Direction mplsXCExtEntry

 Once the reverse path information is negotiated using the signaling
 protocol, the reverse-direction mplsXCExtEntry will be created for
 associating the opposite-direction XC entry and tunnel table entry.

Venkatesan, et al. Standards Track [Page 25] RFC 7453 MPLS-TP MIB February 2015

10. MPLS Textual Convention Extension MIB Definitions

 MPLS-TC-EXT-STD-MIB DEFINITIONS ::= BEGIN
 IMPORTS
    MODULE-IDENTITY, Unsigned32
       FROM SNMPv2-SMI               -- RFC 2578
    TEXTUAL-CONVENTION
       FROM SNMPv2-TC                -- RFC 2579
    mplsStdMIB
       FROM MPLS-TC-STD-MIB          -- RFC 3811
    ;
 mplsTcExtStdMIB MODULE-IDENTITY
    LAST-UPDATED
       "201502020000Z" -- February 2, 2015
    ORGANIZATION
       "Multiprotocol Label Switching (MPLS) Working Group"
    CONTACT-INFO
       "
              Venkatesan Mahalingam
              Dell Inc,
              5450 Great America Parkway,
              Santa Clara, CA 95054, USA
        Email: venkat.mahalingams@gmail.com
              Kannan KV Sampath
              Redeem,
              India
        Email: kannankvs@gmail.com
              Sam Aldrin
              Huawei Technologies
              2330 Central Express Way,
              Santa Clara, CA 95051, USA
        Email:  aldrin.ietf@gmail.com
              Thomas D. Nadeau
        Email: tnadeau@lucidvision.com
       "
    DESCRIPTION
       "This MIB module contains Textual Conventions for LSPs of MPLS-
        based transport networks.

Venkatesan, et al. Standards Track [Page 26] RFC 7453 MPLS-TP MIB February 2015

        Copyright (c) 2015 IETF Trust and the persons identified as
        authors of the code.  All rights reserved.
        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject to
        the license terms contained in, the Simplified BSD License set
        forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info)."
  1. - Revision history.
    REVISION
       "201502020000Z" -- February 2, 2015
    DESCRIPTION
         "MPLS Textual Convention Extensions"
    ::= { mplsStdMIB 17 }
 MplsGlobalId ::= TEXTUAL-CONVENTION
    STATUS      current
    DESCRIPTION
         "This object contains the Textual Convention for an IP-based
          operator-unique identifier (Global_ID).  The Global_ID can
          contain the 2-octet or 4-octet value of the operator's
          Autonomous System Number (ASN).
          When the Global_ID is derived from a 2-octet ASN,
          the two high-order octets of this 4-octet identifier
          MUST be set to zero (0x00).  Further, ASN 0 is reserved.
          The size of the Global_ID string MUST be zero if
          the Global_ID is invalid.
          Note that a Global_ID of zero is limited to entities
          contained within a single operator and MUST NOT be used
          across a Network-to-Network Interface (NNI).  A non-zero
          Global_ID MUST be derived from an ASN owned by
          the operator."
    REFERENCE
         "MPLS Transport Profile (MPLS-TP) Identifiers, RFC 6370,
          Section 3"
    SYNTAX  OCTET STRING (SIZE (4))
 MplsCcId ::= TEXTUAL-CONVENTION
 STATUS      current
 DESCRIPTION
      "The CC (Country Code) is a string of two characters, each
       being an uppercase Basic Latin alphabetic (i.e., A-Z).

Venkatesan, et al. Standards Track [Page 27] RFC 7453 MPLS-TP MIB February 2015

       The characters are encoded using ITU-T Recommendation T.50.
       The size of the CC string MUST be zero if the CC identifier
       is invalid."
 REFERENCE
      "MPLS-TP Identifiers Following ITU-T Conventions,
       RFC 6923, Section 3.
       International Reference Alphabet (IRA) (Formerly
       International Alphabet No. 5 or IA5) - Information
       technology - 7-bit coded character set for information
       exchange, ITU-T Recommendation T.50, September 1992."
 SYNTAX  OCTET STRING (SIZE (0|2))
 MplsIccId ::= TEXTUAL-CONVENTION
 STATUS      current
 DESCRIPTION
      "The ICC is a string of one to six characters, each
       an uppercase Basic Latin alphabetic (i.e., A-Z) or
       numeric (i.e., 0-9).  The characters are encoded
       using ITU-T Recommendation T.50.  The size of
       the ICC string MUST be zero if the ICC identifier
       is invalid."
 REFERENCE
      "MPLS-TP Identifiers Following ITU-T Conventions,
       RFC 6923, Section 3.
       International Reference Alphabet (IRA) (Formerly
       International Alphabet No. 5 or IA5) - Information
       technology - 7-bit coded character set for information
       exchange, ITU-T Recommendation T.50, September 1992."
 SYNTAX  OCTET STRING (SIZE (0|1..6))
 MplsNodeId ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "d"
    STATUS      current
    DESCRIPTION
        "The Node_ID is assigned within the scope of
         the Global_ID/ICC_Operator_ID.
         When IPv4 addresses are in use, the value of this object
         can be derived from the LSR's IPv4 loopback address.
         When IPv6 addresses are in use, the value of this object
         can be a 32-bit value unique within the scope of
         a Global_ID.
         Note that, when IP reachability is not needed, the 32-bit
         Node_ID is not required to have any association
         with the IPv4 address space.  The value of 0 indicates
         an invalid Node_ID."

Venkatesan, et al. Standards Track [Page 28] RFC 7453 MPLS-TP MIB February 2015

    REFERENCE
         "MPLS Transport Profile (MPLS-TP) Identifiers, RFC 6370,
          Section 4"
    SYNTAX  Unsigned32 (0|1..4294967295)
  1. - MPLS-TC-EXT-STD-MIB module ends

END

11. MPLS Identifier MIB Definitions

 MPLS-ID-STD-MIB DEFINITIONS ::= BEGIN
 IMPORTS
  MODULE-IDENTITY, OBJECT-TYPE
     FROM SNMPv2-SMI                                 -- RFC 2578
  MODULE-COMPLIANCE, OBJECT-GROUP
     FROM SNMPv2-CONF                                -- RFC 2580
  mplsStdMIB
     FROM MPLS-TC-STD-MIB                            -- RFC 3811
  MplsGlobalId, MplsCcId, MplsIccId, MplsNodeId
     FROM MPLS-TC-EXT-STD-MIB
  ;
mplsIdStdMIB MODULE-IDENTITY
  LAST-UPDATED
      "201502020000Z" -- February 2, 2015
  ORGANIZATION
     "Multiprotocol Label Switching (MPLS) Working Group"
  CONTACT-INFO
     "
            Venkatesan Mahalingam
            Dell Inc,
            5450 Great America Parkway,
            Santa Clara, CA 95054, USA
      Email: venkat.mahalingams@gmail.com
            Kannan KV Sampath
            Redeem,
            India
      Email: kannankvs@gmail.com
            Sam Aldrin
            Huawei Technologies
            2330 Central Express Way,
            Santa Clara, CA 95051, USA
      Email:  aldrin.ietf@gmail.com

Venkatesan, et al. Standards Track [Page 29] RFC 7453 MPLS-TP MIB February 2015

            Thomas D. Nadeau
      Email: tnadeau@lucidvision.com
    "
  DESCRIPTION
      "This MIB module contains identifier object definitions for
       MPLS Traffic Engineering in transport networks.
       Copyright (c) 2015 IETF Trust and the persons identified as
       authors of the code.  All rights reserved.
       Redistribution and use in source and binary forms, with or
       without modification, is permitted pursuant to, and subject to
       the license terms contained in, the Simplified BSD License set
       forth in Section 4.c of the IETF Trust's Legal Provisions
       Relating to IETF Documents
       (http://trustee.ietf.org/license-info)."
  1. - Revision history.
  REVISION
      "201502020000Z" -- February 2, 2015
  DESCRIPTION
       "This MIB modules defines the MIB objects for MPLS-TP
        identifiers"
  ::= { mplsStdMIB 18 }
  1. - notifications

mplsIdNotifications OBJECT IDENTIFIER ::= { mplsIdStdMIB 0 }

  1. - tables, scalars

mplsIdObjects OBJECT IDENTIFIER ::= { mplsIdStdMIB 1 }

  1. - conformance

mplsIdConformance OBJECT IDENTIFIER ::= { mplsIdStdMIB 2 }

  1. - MPLS common objects
mplsIdGlobalId OBJECT-TYPE
     SYNTAX      MplsGlobalId
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
         "This object allows the operator or service provider to
          assign a unique operator identifier, also called the MPLS-TP
          Global_ID.
          If this value is used in mplsTunnelExtNodeConfigGlobalId
          for mapping Global_ID::Node_ID with the local identifier,
          then this object value MUST NOT be changed."
    ::= { mplsIdObjects 1 }

Venkatesan, et al. Standards Track [Page 30] RFC 7453 MPLS-TP MIB February 2015

mplsIdNodeId OBJECT-TYPE
     SYNTAX      MplsNodeId
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "This object allows the operator or service provider to
         assign a unique MPLS-TP Node_ID.  The Node_ID is assigned
         within the scope of the Global_ID/ICC_Operator_ID.
         If this value is used in mplsTunnelExtNodeConfigNodeId
         for mapping Global_ID::Node_ID with the local identifier,
         then this object value SHOULD NOT be changed.
         If this value is used in mplsTunnelExtNodeConfigNodeId
         for mapping ICC_Operator_ID::Node_ID with the local
         identifier, then this object value MUST NOT be changed."
    ::= { mplsIdObjects 2 }
mplsIdCc OBJECT-TYPE
     SYNTAX      MplsCcId
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "This object allows the operator or service provider to
         assign a Country Code (CC) to the node.  Global
         uniqueness of ICC is assured by concatenating the ICC
         with a Country Code (CC).
         If this value is used in mplsTunnelExtNodeConfigCcId
         for mapping ICC_Operator_ID::Node_ID with the local
         identifier, then this object value MUST NOT be changed."
    REFERENCE
         "MPLS-TP Identifiers Following ITU-T Conventions,
          RFC 6923, Section 3"
        ::= { mplsIdObjects 3 }
mplsIdIcc OBJECT-TYPE
     SYNTAX      MplsIccId
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "This object allows the operator or service provider to
         assign a unique MPLS-TP ITU-T Carrier Code (ICC) to
         the node.  Together, the CC and the ICC form
         the ICC_Operator_ID as CC::ICC.
         If this value is used in mplsTunnelExtNodeConfigIccId
         for mapping ICC_Operator_ID::Node_ID with the local
         identifier, then this object value MUST NOT be changed."
    REFERENCE
         "MPLS-TP Identifiers Following ITU-T Conventions,
          RFC 6923, Section 3"

Venkatesan, et al. Standards Track [Page 31] RFC 7453 MPLS-TP MIB February 2015

        ::= { mplsIdObjects 4 }
  1. - Module compliance.
mplsIdCompliances
   OBJECT IDENTIFIER ::= { mplsIdConformance 1 }
mplsIdGroups
   OBJECT IDENTIFIER ::= { mplsIdConformance 2 }
  1. - Compliance requirement for fully compliant implementations.
mplsIdModuleFullCompliance MODULE-COMPLIANCE
   STATUS current
   DESCRIPTION
        "Compliance statement for agents that provide full
          support of the MPLS-ID-STD-MIB module."
   MODULE -- this module
  1. - The mandatory group has to be implemented by all LSRs that
  2. - originate, terminate, or act as transit for MPLS-TP Tunnels.
      GROUP mplsIdIpOperatorGroup
      DESCRIPTION
          "This group is mandatory for devices that support
           IP-based identifier configuration."
      GROUP mplsIdIccOperatorGroup
      DESCRIPTION
          "This group is mandatory for devices that support
           ICC-based identifier configuration."
       ::= { mplsIdCompliances 1 }
  1. - Compliance requirement for read-only implementations.
      mplsIdModuleReadOnlyCompliance MODULE-COMPLIANCE
         STATUS current
         DESCRIPTION
              "Compliance statement for agents that only provide
               read-only support for the MPLS-ID-STD-MIB module."
      MODULE -- this module

Venkatesan, et al. Standards Track [Page 32] RFC 7453 MPLS-TP MIB February 2015

      GROUP mplsIdIpOperatorGroup
      DESCRIPTION
          "This group is mandatory for devices that support
           IP-based identifier configuration."
      GROUP mplsIdIccOperatorGroup
      DESCRIPTION
          "This group is mandatory for devices that support
           ICC-based identifier configuration."
      OBJECT   mplsIdGlobalId
      MIN-ACCESS  read-only
      DESCRIPTION
        "Write access is not required."
      OBJECT   mplsIdNodeId
      MIN-ACCESS  read-only
      DESCRIPTION
        "Write access is not required."
      OBJECT   mplsIdCc
      MIN-ACCESS  read-only
      DESCRIPTION
        "Write access is not required."
      OBJECT   mplsIdIcc
      MIN-ACCESS  read-only
      DESCRIPTION
        "Write access is not required."
      ::= { mplsIdCompliances 2 }
  1. - Units of conformance.
      mplsIdIpOperatorGroup OBJECT-GROUP
            OBJECTS { mplsIdGlobalId,
                      mplsIdNodeId
            }
            STATUS  current
            DESCRIPTION
                "The objects in this group are optional for an
                 ICC-based node."
            ::= { mplsIdGroups 1 }

Venkatesan, et al. Standards Track [Page 33] RFC 7453 MPLS-TP MIB February 2015

      mplsIdIccOperatorGroup OBJECT-GROUP
            OBJECTS { mplsIdNodeId,
                      mplsIdCc,
                      mplsIdIcc
            }
            STATUS  current
            DESCRIPTION
               "The objects in this group are optional for an
                IP-based node."
            ::= { mplsIdGroups 2 }
  1. - MPLS-ID-STD-MIB module ends

END

12. MPLS LSR Extension MIB Definitions

 MPLS-LSR-EXT-STD-MIB DEFINITIONS ::= BEGIN
 IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE
       FROM SNMPv2-SMI                                 -- RFC 2578
    MODULE-COMPLIANCE, OBJECT-GROUP
       FROM SNMPv2-CONF                                -- RFC 2580
    mplsStdMIB
       FROM MPLS-TC-STD-MIB                            -- RFC 3811
    RowPointer
       FROM SNMPv2-TC                                  -- RFC 2579
    mplsXCIndex, mplsXCInSegmentIndex, mplsXCOutSegmentIndex,
    mplsInterfaceGroup, mplsInSegmentGroup, mplsOutSegmentGroup,
    mplsXCGroup, mplsLsrNotificationGroup
       FROM MPLS-LSR-STD-MIB;                          -- RFC 3813
 mplsLsrExtStdMIB MODULE-IDENTITY
    LAST-UPDATED
       "201502020000Z" -- February 2, 2015
    ORGANIZATION
       "Multiprotocol Label Switching (MPLS) Working Group"
    CONTACT-INFO
       "
              Venkatesan Mahalingam
              Dell Inc,
              5450 Great America Parkway,
              Santa Clara, CA 95054, USA
        Email: venkat.mahalingams@gmail.com

Venkatesan, et al. Standards Track [Page 34] RFC 7453 MPLS-TP MIB February 2015

              Kannan KV Sampath
              Redeem,
              India
        Email: kannankvs@gmail.com
              Sam Aldrin
              Huawei Technologies
              2330 Central Express Way,
              Santa Clara, CA 95051, USA
        Email:  aldrin.ietf@gmail.com
              Thomas D. Nadeau
        Email: tnadeau@lucidvision.com
      "
    DESCRIPTION
      "This MIB module contains generic object definitions for
       MPLS LSRs in transport networks.
       Copyright (c) 2015 IETF Trust and the persons identified as
       authors of the code.  All rights reserved.
       Redistribution and use in source and binary forms, with or
       without modification, is permitted pursuant to, and subject to
       the license terms contained in, the Simplified BSD License set
       forth in Section 4.c of the IETF Trust's Legal Provisions
       Relating to IETF Documents
       (http://trustee.ietf.org/license-info)."
  1. - Revision history.
    REVISION
       "201502020000Z" -- February 2, 2015
    DESCRIPTION
         "MPLS LSR-specific MIB objects extension"
    ::= { mplsStdMIB 19 }
  1. - notifications

mplsLsrExtNotifications OBJECT IDENTIFIER ::= { mplsLsrExtStdMIB 0 }

  1. - tables, scalars

mplsLsrExtObjects OBJECT IDENTIFIER

                          ::= { mplsLsrExtStdMIB 1 }
 -- conformance
 mplsLsrExtConformance   OBJECT IDENTIFIER
                          ::= { mplsLsrExtStdMIB 2 }
  1. - MPLS LSR common objects

Venkatesan, et al. Standards Track [Page 35] RFC 7453 MPLS-TP MIB February 2015

 mplsXCExtTable  OBJECT-TYPE
     SYNTAX        SEQUENCE OF MplsXCExtEntry
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
        "This table sparse augments the mplsXCTable of
         MPLS-LSR-STD-MIB (RFC 3813) to provide MPLS-TP-specific
         information about associated tunnel information"
     REFERENCE
        "Multiprotocol Label Switching (MPLS) Label Switching
         Router (LSR) Management Information Base (MIB), RFC 3813."
 ::= { mplsLsrExtObjects 1 }
 mplsXCExtEntry  OBJECT-TYPE
     SYNTAX        MplsXCExtEntry
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
        "An entry in this table sparsely extends the cross-connect
         information represented by an entry in
         the mplsXCTable in MPLS-LSR-STD-MIB (RFC 3813) through
         a sparse augmentation.  An entry can be created by
         a network operator via SNMP SET commands or in
         response to signaling protocol events."
     REFERENCE
        "Multiprotocol Label Switching (MPLS) Label Switching
         Router (LSR) Management Information Base (MIB), RFC 3813."
   INDEX { mplsXCIndex, mplsXCInSegmentIndex,
         mplsXCOutSegmentIndex }
  ::= { mplsXCExtTable 1 }
 MplsXCExtEntry ::= SEQUENCE {
    mplsXCExtTunnelPointer        RowPointer,
    mplsXCExtOppositeDirXCPtr     RowPointer
 }
 mplsXCExtTunnelPointer OBJECT-TYPE
     SYNTAX        RowPointer
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
        "This read-only object indicates the back pointer to
         the tunnel entry segment.
         The only valid value for Tunnel Pointer is
         mplsTunnelTable entry."

Venkatesan, et al. Standards Track [Page 36] RFC 7453 MPLS-TP MIB February 2015

     REFERENCE
        "Multiprotocol Label Switching (MPLS) Label Switching
         Router (LSR) Management Information Base (MIB), RFC 3813."
  ::= { mplsXCExtEntry 1 }
 mplsXCExtOppositeDirXCPtr OBJECT-TYPE
     SYNTAX        RowPointer
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "This object indicates the pointer to the opposite-
         direction XC entry.  This object cannot be modified if
         mplsXCRowStatus for the corresponding entry in the
         mplsXCTable is active(1).  If this pointer is not set or
         removed, mplsXCOperStatus should be set to down(2)."
     REFERENCE
        "Multiprotocol Label Switching (MPLS) Label Switching
         Router (LSR) Management Information Base (MIB), RFC 3813."
  ::= { mplsXCExtEntry 2 }
  mplsLsrExtCompliances
     OBJECT IDENTIFIER ::= { mplsLsrExtConformance 1 }
  mplsLsrExtGroups
     OBJECT IDENTIFIER ::= { mplsLsrExtConformance 2 }
  1. - Compliance requirement for fully compliant implementations.
  mplsLsrExtModuleFullCompliance MODULE-COMPLIANCE
      STATUS current
      DESCRIPTION
         "Compliance statement for agents that provide full support
          for MPLS-LSR-EXT-STD-MIB.
          The mandatory group has to be implemented by all LSRs
          that originate, terminate, or act as transit for
          TE-LSPs/tunnels.
          In addition, depending on the type of tunnels supported,
          other groups become mandatory as explained below."
   MODULE MPLS-LSR-STD-MIB -- The MPLS-LSR-STD-MIB, RFC 3813
   MANDATORY-GROUPS {
     mplsInSegmentGroup,
     mplsOutSegmentGroup,
     mplsXCGroup,
     mplsLsrNotificationGroup
   }

Venkatesan, et al. Standards Track [Page 37] RFC 7453 MPLS-TP MIB February 2015

   MODULE -- this module
   MANDATORY-GROUPS    {
     mplsXCExtGroup
   }
   ::= { mplsLsrExtCompliances 1 }
  1. - Compliance requirement for implementations that provide
  2. - read-only access.
   mplsLsrExtModuleReadOnlyCompliance MODULE-COMPLIANCE
     STATUS current
     DESCRIPTION
        "Compliance requirement for implementations that only
         provide read-only support for MPLS-LSR-EXT-STD-MIB.
         Such devices can then be monitored but cannot be
         configured using this MIB module."
   MODULE MPLS-LSR-STD-MIB
   MANDATORY-GROUPS {
       mplsInterfaceGroup,
       mplsInSegmentGroup,
       mplsOutSegmentGroup
   }
   MODULE -- this module
   GROUP mplsXCExtReadOnlyObjectsGroup
   DESCRIPTION
         "This group is mandatory for devices that support
          opposite-direction XC configuration of tunnels."
  1. - mplsXCExtTable

OBJECT mplsXCExtOppositeDirXCPtr

        MIN-ACCESS   read-only
        DESCRIPTION
            "Write access is not required.
             This object indicates the pointer to the opposite-
             direction XC entry.  The only valid value for XC
             Pointer is mplsXCTable entry."
        ::= { mplsLsrExtCompliances 2 }
  1. - Units of conformance.

Venkatesan, et al. Standards Track [Page 38] RFC 7453 MPLS-TP MIB February 2015

   mplsXCExtGroup  OBJECT-GROUP
   OBJECTS {
       mplsXCExtTunnelPointer,
       mplsXCExtOppositeDirXCPtr
   }
   STATUS  current
   DESCRIPTION
       "This object should be supported in order to access
       the tunnel entry from the XC entry."
   ::= { mplsLsrExtGroups 1 }
   mplsXCExtReadOnlyObjectsGroup OBJECT-GROUP
   OBJECTS {
       mplsXCExtTunnelPointer,
       mplsXCExtOppositeDirXCPtr
   }
   STATUS  current
   DESCRIPTION
       "This Object is needed to associate the opposite-direction
       (forward/reverse) XC entry."
   ::= { mplsLsrExtGroups 2 }
  1. - MPLS-LSR-EXT-STD-MIB module ends

END

13. MPLS Tunnel Extension MIB Definitions

 This MIB module imports from [RFC2578], [RFC2579], [RFC2580],
 [RFC3289], [RFC3811], and [RFC3812].
 MPLS-TE-EXT-STD-MIB DEFINITIONS ::= BEGIN
 IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE
       FROM SNMPv2-SMI                               -- RFC 2578
    MODULE-COMPLIANCE, OBJECT-GROUP
       FROM SNMPv2-CONF                              -- RFC 2580
    TruthValue, RowStatus, RowPointer, StorageType
       FROM SNMPv2-TC                                -- RFC 2579
    IndexIntegerNextFree
       FROM DIFFSERV-MIB                             -- RFC 3289
    MplsGlobalId, MplsNodeId, MplsCcId, MplsIccId
       FROM MPLS-TC-EXT-STD-MIB
    mplsStdMIB, MplsTunnelIndex, MplsTunnelInstanceIndex,
    MplsExtendedTunnelId
       FROM MPLS-TC-STD-MIB                          -- RFC 3811
    mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId,
    mplsTunnelEgressLSRId

Venkatesan, et al. Standards Track [Page 39] RFC 7453 MPLS-TP MIB February 2015

       FROM MPLS-TE-STD-MIB                          -- RFC 3812
    ;
 mplsTeExtStdMIB MODULE-IDENTITY
    LAST-UPDATED
       "201502020000Z" -- February 2, 2015
    ORGANIZATION
       "Multiprotocol Label Switching (MPLS) Working Group"
    CONTACT-INFO
       "
              Venkatesan Mahalingam
              Dell Inc,
              5450 Great America Parkway,
              Santa Clara, CA 95054, USA
        Email: venkat.mahalingams@gmail.com
              Kannan KV Sampath
              Redeem,
              India
        Email: kannankvs@gmail.com
              Sam Aldrin
              Huawei Technologies
              2330 Central Express Way,
              Santa Clara, CA 95051, USA
        Email:  aldrin.ietf@gmail.com
              Thomas D. Nadeau
        Email: tnadeau@lucidvision.com
      "
    DESCRIPTION
      "This MIB module contains generic object definitions for
       extending the MPLS Traffic Engineering tunnels in transport
       networks.
       Copyright (c) 2015 IETF Trust and the persons identified as
       authors of the code.  All rights reserved.
       Redistribution and use in source and binary forms, with or
       without modification, is permitted pursuant to, and subject to
       the license terms contained in, the Simplified BSD License set
       forth in Section 4.c of the IETF Trust's Legal Provisions
       Relating to IETF Documents
       (http://trustee.ietf.org/license-info)."

Venkatesan, et al. Standards Track [Page 40] RFC 7453 MPLS-TP MIB February 2015

  1. - Revision history.
    REVISION
     "201502020000Z" -- February 2, 2015
    DESCRIPTION
         "MPLS TE MIB objects extension"
    ::= { mplsStdMIB 20 }
  1. - Top-level components of this MIB module.
  1. - tables, scalars

mplsTeExtObjects OBJECT IDENTIFIER

                                  ::= { mplsTeExtStdMIB 0 }
 -- conformance
 mplsTeExtConformance   OBJECT IDENTIFIER
                                  ::= { mplsTeExtStdMIB 1 }
  1. - Start of MPLS Transport Profile Node configuration table
mplsTunnelExtNodeConfigLocalIdNext OBJECT-TYPE
 SYNTAX        IndexIntegerNextFree (0..16777215)
 MAX-ACCESS    read-only
 STATUS        current
 DESCRIPTION
    "This object contains an unused value for
     mplsTunnelExtNodeConfigLocalId, or a zero to indicate
     that none exist.  Negative values are not allowed,
     as they do not correspond to valid values of
     mplsTunnelExtNodeConfigLocalId."
  ::= { mplsTeExtObjects 1 }
  mplsTunnelExtNodeConfigTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsTunnelExtNodeConfigEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
     "This table allows the operator to map a node or
      LSR identifier (IP-compatible [Global_ID::Node_ID] or
      ICC-based [ICC_Operator_ID::Node_ID]) with a local
      identifier.
      This table is created to reuse the existing
      mplsTunnelTable for MPLS-based transport network
      tunnels also.

Venkatesan, et al. Standards Track [Page 41] RFC 7453 MPLS-TP MIB February 2015

      Since the MPLS tunnel's Ingress/Egress LSR identifiers'
      size (Unsigned32) value is not compatible for
      MPLS-TP Tunnel, i.e., Global_ID::Node_ID of size 8 bytes and
      ICC_Operator_ID::Node_ID of size 12 bytes, there exists a
      need to map the Global_ID::Node_ID or ICC_Operator_ID::Node_ID
      with the local identifier of size 4 bytes (Unsigned32) value
      in order to index (Ingress/Egress LSR identifier)
      the existing mplsTunnelTable."
   ::= { mplsTeExtObjects 2 }
  mplsTunnelExtNodeConfigEntry OBJECT-TYPE
   SYNTAX        MplsTunnelExtNodeConfigEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
      "An entry in this table represents a mapping
      identification for the operator or service provider
      to a node or an LSR.
      As per RFC 6370, IP-compatible mapping is represented
      as Global_ID::Node_ID.
      As per RFC 6923, the CC and the ICC form the ICC_Operator_ID
      as CC::ICC, and ICC-compatible mapping is represented
      as ICC_Operator_ID::Node_ID.
      Note: Each entry in this table should have a unique
      [Global_ID and Node_ID] or [CC::ICC and Node_ID] combination."
      INDEX { mplsTunnelExtNodeConfigLocalId }
      ::= { mplsTunnelExtNodeConfigTable 1 }
  MplsTunnelExtNodeConfigEntry ::= SEQUENCE {
        mplsTunnelExtNodeConfigLocalId     MplsExtendedTunnelId,
        mplsTunnelExtNodeConfigGlobalId    MplsGlobalId,
        mplsTunnelExtNodeConfigCcId        MplsCcId,
        mplsTunnelExtNodeConfigIccId       MplsIccId,
        mplsTunnelExtNodeConfigNodeId      MplsNodeId,
        mplsTunnelExtNodeConfigIccValid    TruthValue,
        mplsTunnelExtNodeConfigStorageType StorageType,
        mplsTunnelExtNodeConfigRowStatus   RowStatus
  }
  mplsTunnelExtNodeConfigLocalId  OBJECT-TYPE
     SYNTAX        MplsExtendedTunnelId
     MAX-ACCESS    not-accessible
     STATUS        current

Venkatesan, et al. Standards Track [Page 42] RFC 7453 MPLS-TP MIB February 2015

     DESCRIPTION
       "This object is used in accommodating the bigger-
        size Global_ID::Node_ID and/or the ICC_Operator_ID::Node_ID
        with the smaller-size LSR identifier in order to index
        the mplsTunnelTable.
        The local identifier is configured between 0 and 16777215,
        as the valid IP address range starts from
        16777216(01.00.00.00).
        This range is chosen to determine whether the
        mplsTunnelTable's Ingress/Egress LSR ID is an IP address or
        local identifier.  If the configured range is not an
        IP address, the operator is expected to retrieve the
        complete information (Global_ID::Node_ID or
        ICC_Operator_ID::Node_ID) from mplsTunnelExtNodeConfigTable.
        This way, the existing mplsTunnelTable is reused for
        bidirectional tunnel extensions for MPLS-based transport
        networks.
        The local identifier allows the operator to assign
        a unique identifier to map Global_ID::Node_ID and/or
        ICC_Operator_ID::Node_ID.  As this local identifier is unique
        within the node and the same syntax of this object can be
        used for MPLS-TE tunnel also, it is up to the operator/local
        management entity to choose a non-conflicting value for
        indexing the MPLS and MPLS-TP tunnel entries."
     ::= { mplsTunnelExtNodeConfigEntry 1 }
  mplsTunnelExtNodeConfigGlobalId  OBJECT-TYPE
     SYNTAX        MplsGlobalId
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
       "This object indicates the Global Operator Identifier.
        This object has no meaning when
        mplsTunnelExtNodeConfigIccValid is set true."
     REFERENCE
           "MPLS Transport Profile (MPLS-TP) Identifiers, RFC 6370,
            Section 3."
     ::= { mplsTunnelExtNodeConfigEntry 2 }
  mplsTunnelExtNodeConfigCcId OBJECT-TYPE
       SYNTAX      MplsCcId
       MAX-ACCESS  read-create
       STATUS      current

Venkatesan, et al. Standards Track [Page 43] RFC 7453 MPLS-TP MIB February 2015

       DESCRIPTION
          "This object allows the operator or service provider to
           configure a unique MPLS-TP ITU-T Country Code (CC)
           either for Ingress ID or Egress ID.
           This object has no meaning when
           mplsTunnelExtNodeConfigIccValid is set to false."
          REFERENCE
             "MPLS-TP Identifiers Following ITU-T Conventions,
             RFC 6923, Section 3"
     ::= { mplsTunnelExtNodeConfigEntry 3 }
     mplsTunnelExtNodeConfigIccId OBJECT-TYPE
          SYNTAX      MplsIccId
          MAX-ACCESS  read-create
          STATUS      current
          DESCRIPTION
             "This object allows the operator or service provider to
              configure a unique MPLS-TP ITU-T Carrier Code (ICC)
              either for Ingress ID or Egress ID.
              This object has no meaning when
              mplsTunnelExtNodeConfigIccValid is set to false."
          REFERENCE
             "MPLS-TP Identifiers Following ITU-T Conventions,
              RFC 6923, Section 3"
     ::= { mplsTunnelExtNodeConfigEntry 4 }
     mplsTunnelExtNodeConfigNodeId  OBJECT-TYPE
        SYNTAX        MplsNodeId
        MAX-ACCESS    read-create
        STATUS        current
        DESCRIPTION
           "This object indicates the Node_ID within the scope
            of a Global_ID or ICC_Operator_ID."
        REFERENCE
            "MPLS Transport Profile (MPLS-TP) Identifiers, RFC 6370,
             Section 4."
        ::= { mplsTunnelExtNodeConfigEntry 5 }
     mplsTunnelExtNodeConfigIccValid  OBJECT-TYPE
        SYNTAX        TruthValue
        MAX-ACCESS    read-create
        STATUS        current
        DESCRIPTION
           "Denotes whether or not this entry uses
            mplsTunnelExtNodeConfigCcId,
            mplsTunnelExtNodeConfigIccId, and

Venkatesan, et al. Standards Track [Page 44] RFC 7453 MPLS-TP MIB February 2015

            mplsTunnelExtNodeConfigNodeId for mapping
            the ICC-based identifiers with the local identifier.
            Note that if this variable is set to false, then the
            mplsTunnelExtNodeConfigGlobalId and
            mplsTunnelExtNodeConfigNodeId objects should have
            the valid information."
        DEFVAL { false }
          ::= { mplsTunnelExtNodeConfigEntry 6 }
     mplsTunnelExtNodeConfigStorageType OBJECT-TYPE
        SYNTAX        StorageType
        MAX-ACCESS    read-create
        STATUS        current
        DESCRIPTION
         "This variable indicates the storage type for this
          object.
          Conceptual rows having the value 'permanent'
          need not allow write-access to any columnar
          objects in the row."
        DEFVAL { volatile }
        ::= { mplsTunnelExtNodeConfigEntry 7 }
  mplsTunnelExtNodeConfigRowStatus OBJECT-TYPE
     SYNTAX        RowStatus
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "This object allows the operator to create, modify,
         and/or delete a row in this table."
     ::= { mplsTunnelExtNodeConfigEntry 8 }
  1. - End of MPLS Transport Profile Node configuration table
  1. - Start of MPLS Transport Profile Node IP-compatible
  2. - mapping table
mplsTunnelExtNodeIpMapTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsTunnelExtNodeIpMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This read-only table allows the operator to retrieve
        the local identifier for a given Global_ID::Node_ID in an
        IP-compatible operator environment.
        This table MAY be used in on-demand and/or proactive
        OAM operations to get the Ingress/Egress LSR identifier

Venkatesan, et al. Standards Track [Page 45] RFC 7453 MPLS-TP MIB February 2015

        (local identifier) from Src-Global_Node_ID
        or Dst-Global_Node_ID.  The Ingress and Egress LSR
        identifiers are used to retrieve the tunnel entry.
        This table returns nothing when the associated entry
        is not defined in mplsTunnelExtNodeConfigTable."
   ::= { mplsTeExtObjects 3 }
  mplsTunnelExtNodeIpMapEntry OBJECT-TYPE
   SYNTAX        MplsTunnelExtNodeIpMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
         "An entry in this table represents a mapping of
          Global_ID::Node_ID with the local identifier.
          An entry in this table is created automatically when
          the local identifier is associated with Global_ID and
          Node_Id in the mplsTunnelExtNodeConfigTable.
          Note: Each entry in this table should have a unique
          Global_ID and Node_ID combination."
    INDEX { mplsTunnelExtNodeIpMapGlobalId,
            mplsTunnelExtNodeIpMapNodeId
          }
    ::= { mplsTunnelExtNodeIpMapTable 1 }
  MplsTunnelExtNodeIpMapEntry ::= SEQUENCE {
        mplsTunnelExtNodeIpMapGlobalId    MplsGlobalId,
        mplsTunnelExtNodeIpMapNodeId      MplsNodeId,
        mplsTunnelExtNodeIpMapLocalId     MplsExtendedTunnelId
  }
  mplsTunnelExtNodeIpMapGlobalId  OBJECT-TYPE
     SYNTAX        MplsGlobalId
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
       "This object indicates the Global_ID."
     ::= { mplsTunnelExtNodeIpMapEntry 1 }
  mplsTunnelExtNodeIpMapNodeId  OBJECT-TYPE
     SYNTAX        MplsNodeId
     MAX-ACCESS    not-accessible
     STATUS        current

Venkatesan, et al. Standards Track [Page 46] RFC 7453 MPLS-TP MIB February 2015

     DESCRIPTION
       "This object indicates the Node_ID within the
        operator."
     ::= { mplsTunnelExtNodeIpMapEntry 2 }
  mplsTunnelExtNodeIpMapLocalId  OBJECT-TYPE
     SYNTAX        MplsExtendedTunnelId
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
       "This object contains an IP-compatible local identifier
        that is defined in mplsTunnelExtNodeConfigTable."
     ::= { mplsTunnelExtNodeIpMapEntry 3 }
  1. - End MPLS Transport Profile Node IP compatible table
  1. - Start of MPLS Transport Profile Node ICC based table
  mplsTunnelExtNodeIccMapTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsTunnelExtNodeIccMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
      "This read-only table allows the operator to retrieve
       the local identifier for a given ICC_Operator_ID::Node_ID
       in an ICC operator environment.
       This table MAY be used in on-demand and/or proactive
       OAM operations to get the Ingress/Egress LSR
       identifier (local identifier) from Src-ICC
       or Dst-ICC.  The Ingress and Egress LSR
       identifiers are used to retrieve the tunnel entry.
       This table returns nothing when the associated entry
       is not defined in mplsTunnelExtNodeConfigTable."
   ::= { mplsTeExtObjects 4 }
  mplsTunnelExtNodeIccMapEntry OBJECT-TYPE
   SYNTAX        MplsTunnelExtNodeIccMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
         "An entry in this table represents a mapping of
          ICC_Operator_ID::Node_ID with the local identifier.
          An entry in this table is created automatically when
          the local identifier is associated with
          ICC_Operator_ID::Node_ID in
          the mplsTunnelExtNodeConfigTable."

Venkatesan, et al. Standards Track [Page 47] RFC 7453 MPLS-TP MIB February 2015

    INDEX { mplsTunnelExtNodeIccMapCcId,
            mplsTunnelExtNodeIccMapIccId,
            mplsTunnelExtNodeIccMapNodeId }
    ::= { mplsTunnelExtNodeIccMapTable 1 }
  MplsTunnelExtNodeIccMapEntry ::= SEQUENCE {
        mplsTunnelExtNodeIccMapCcId       MplsCcId,
        mplsTunnelExtNodeIccMapIccId      MplsIccId,
        mplsTunnelExtNodeIccMapNodeId     MplsNodeId,
        mplsTunnelExtNodeIccMapLocalId    MplsExtendedTunnelId
  }
  mplsTunnelExtNodeIccMapCcId OBJECT-TYPE
       SYNTAX      MplsCcId
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This object allows the operator or service provider to
           configure a unique MPLS-TP ITU-T Country Code (CC)
           either for Ingress or Egress LSR ID.
           The CC is a string of two alphabetic characters
           represented with uppercase letters (i.e., A-Z)."
       ::= { mplsTunnelExtNodeIccMapEntry 1 }
       mplsTunnelExtNodeIccMapIccId OBJECT-TYPE
            SYNTAX      MplsIccId
            MAX-ACCESS  not-accessible
            STATUS      current
            DESCRIPTION
               "This object allows the operator or service provider
                to configure a unique MPLS-TP ITU-T Carrier
                Code (ICC) either for Ingress or Egress LSR ID.
                The ICC is a string of one to six characters, each
                character being either alphabetic (i.e., A-Z) or
                numeric (i.e., 0-9) characters.  Alphabetic characters
                in the ICC should be represented with uppercase
                letters."
       ::= { mplsTunnelExtNodeIccMapEntry 2 }
       mplsTunnelExtNodeIccMapNodeId  OBJECT-TYPE
          SYNTAX        MplsNodeId
          MAX-ACCESS    not-accessible
          STATUS        current
          DESCRIPTION
            "This object indicates the Node_ID within the
             ICC-based operator."

Venkatesan, et al. Standards Track [Page 48] RFC 7453 MPLS-TP MIB February 2015

       ::= { mplsTunnelExtNodeIccMapEntry 3}
  mplsTunnelExtNodeIccMapLocalId  OBJECT-TYPE
     SYNTAX        MplsExtendedTunnelId
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
       "This object contains an ICC-based local identifier
        that is defined in mplsTunnelExtNodeConfigTable."
  ::= { mplsTunnelExtNodeIccMapEntry 4 }

– End MPLS Transport Profile Node ICC-based table

– Start of MPLS Tunnel table extension

 mplsTunnelExtTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsTunnelExtEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
     "This table represents extensions to mplsTunnelTable
      in order to support MPLS-TP Tunnels.
      As per MPLS-TP Identifiers (RFC 6370), LSP_ID for IP-based
      co-routed bidirectional tunnel:
      A1-{Global_ID::Node_ID::Tunnel_Num}::Z9-{Global_ID::
      Node_ID::Tunnel_Num}::LSP_Num
      LSP_ID for IP based associated bidirectional tunnel:
      A1-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}::
      Z9-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}
      mplsTunnelTable is reused for forming the LSP_ID
      as follows:
      Source Tunnel_Num is mapped with mplsTunnelIndex,
      Source Node_ID is mapped with
      mplsTunnelIngressLSRId, Destination Node_ID is
      mapped with mplsTunnelEgressLSRId, and LSP_Num is mapped with
      mplsTunnelInstance.
      Source Global_ID::Node_ID and/or ICC_Operator_ID::Node_ID and
      Destination Global_ID::Node_ID and/or ICC_Operator_ID::Node-ID
      are maintained in the mplsTunnelExtNodeConfigTable.
      mplsTunnelExtNodeConfigLocalId is used to create an entry
      in mplsTunnelTable."

Venkatesan, et al. Standards Track [Page 49] RFC 7453 MPLS-TP MIB February 2015

   REFERENCE
         "MPLS Transport Profile (MPLS-TP) Identifiers, RFC 6370."
   ::= { mplsTeExtObjects 5 }
  mplsTunnelExtEntry OBJECT-TYPE
  SYNTAX        MplsTunnelExtEntry
  MAX-ACCESS    not-accessible
  STATUS        current
  DESCRIPTION
        "An entry in this table represents additional MPLS-TP-
         specific tunnel configurations."
  INDEX {
    mplsTunnelIndex,
    mplsTunnelInstance,
    mplsTunnelIngressLSRId,
    mplsTunnelEgressLSRId
   }
   ::= { mplsTunnelExtTable 1 }
  MplsTunnelExtEntry ::= SEQUENCE {
       mplsTunnelExtOppositeDirPtr          RowPointer,
       mplsTunnelExtOppositeDirTnlValid     TruthValue,
       mplsTunnelExtDestTnlIndex            MplsTunnelIndex,
       mplsTunnelExtDestTnlLspIndex         MplsTunnelInstanceIndex,
       mplsTunnelExtDestTnlValid            TruthValue,
       mplsTunnelExtIngressLSRLocalIdValid  TruthValue,
       mplsTunnelExtEgressLSRLocalIdValid   TruthValue
  }
  mplsTunnelExtOppositeDirPtr  OBJECT-TYPE
     SYNTAX        RowPointer
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "This object points to the opposite-direction tunnel entry."
  ::= { mplsTunnelExtEntry 1 }
  mplsTunnelExtOppositeDirTnlValid  OBJECT-TYPE
     SYNTAX        TruthValue
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "Denotes whether or not this tunnel uses
         mplsTunnelExtOppositeDirPtr for identifying the opposite-
         direction tunnel information.  Note that if this variable
         is set to true, then the mplsTunnelExtOppositeDirPtr should
         point to the first accessible row of the valid opposite-
         direction tunnel."

Venkatesan, et al. Standards Track [Page 50] RFC 7453 MPLS-TP MIB February 2015

     DEFVAL { false }
       ::= { mplsTunnelExtEntry 2 }
  mplsTunnelExtDestTnlIndex  OBJECT-TYPE
     SYNTAX        MplsTunnelIndex
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "This object is applicable only for the bidirectional
         tunnel that has the forward and reverse LSPs in the
         different tunnel entries.
         The values of this object and the
         mplsTunnelExtDestTnlLspIndex object together can be used
         to identify an opposite-direction LSP, i.e., if the
         mplsTunnelIndex and mplsTunnelInstance hold the value
         for forward LSP, this object and
         mplsTunnelExtDestTnlLspIndex can be used to retrieve
         the reverse-direction LSP and vice versa.
         This object and mplsTunnelExtDestTnlLspIndex values
         provide the first two indices of tunnel entry, and
         the remaining indices can be derived as follows:
         the Ingress and Egress Identifiers should be
         swapped in order to index the other direction tunnel."
        ::= { mplsTunnelExtEntry 3 }
  mplsTunnelExtDestTnlLspIndex  OBJECT-TYPE
     SYNTAX        MplsTunnelInstanceIndex
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "This object is applicable only for the bidirectional
         tunnel that has the forward and reverse LSPs in the
         different tunnel entries.  This object holds
         the instance index of the opposite-direction tunnel."
        ::= { mplsTunnelExtEntry 4 }
  mplsTunnelExtDestTnlValid  OBJECT-TYPE
     SYNTAX        TruthValue
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
        "Denotes whether or not this tunnel uses
         mplsTunnelExtDestTnlIndex and
         mplsTunnelExtDestTnlLspIndex for identifying
         the opposite-direction tunnel information.  Note that if
         this variable is set to true, then the

Venkatesan, et al. Standards Track [Page 51] RFC 7453 MPLS-TP MIB February 2015

         mplsTunnelExtDestTnlIndex and
         mplsTunnelExtDestTnlLspIndex objects should have
         the valid opposite-direction tunnel indices."
     DEFVAL { false }
       ::= { mplsTunnelExtEntry 5 }
  mplsTunnelExtIngressLSRLocalIdValid OBJECT-TYPE
     SYNTAX        TruthValue
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
      "This object denotes whether the mplsTunnelIngressLSRId
       contains the local value that is used to reference
       the complete Ingress Global_ID::Node_ID or ICC_Operator_ID
       from the mplsTunnelExtNodeConfigTable.
       If this object is set to FALSE, mplsTunnelExtNodeConfigTable
       will not contain an entry to reference the local identifier
       with Global_ID::Node_ID or ICC_Operator_ID::Node_ID value.
       This object is set to FALSE for legacy implementations like
       MPLS TE tunnels where mplsTunnelIngressId itself provides
       the complete Ingress LSR ID."
     REFERENCE
       "MPLS-TE-STD-MIB (RFC 3812), Section 11.
        mplsTunnelIngressLSRId object in mplsTunnelTable."
     DEFVAL { false }
       ::= { mplsTunnelExtEntry 6 }
  mplsTunnelExtEgressLSRLocalIdValid OBJECT-TYPE
     SYNTAX        TruthValue
     MAX-ACCESS    read-create
     STATUS        current
     DESCRIPTION
      "This object denotes whether the mplsTunnelEgressLSRId
       contains the local value, which is used to reference
       the complete Egress Global_ID::Node_ID or
       ICC_Operator_ID::Node_ID from
       the mplsTunnelExtNodeConfigTable.
       If this object is set to FALSE, mplsTunnelExtNodeConfigTable
       will not contain an entry to reference the local identifier
       with Global_ID::Node_ID or ICC_Operator_ID::Node_ID value.
       This object is set to FALSE for legacy implementations like
       MPLS TE tunnels where mplsTunnelEgressId itself provides
       the complete Egress LSR ID."

Venkatesan, et al. Standards Track [Page 52] RFC 7453 MPLS-TP MIB February 2015

     REFERENCE
       "MPLS-TE-STD-MIB (RFC 3812), Section 11.
        mplsTunnelEgressLSRId object in mplsTunnelTable."
     DEFVAL { false }
       ::= { mplsTunnelExtEntry 7 }
  1. - End of MPLS Tunnel table extension
  1. - Module compliance.
 mplsTeExtCompliances
    OBJECT IDENTIFIER ::= { mplsTeExtConformance 1 }
 mplsTeExtGroups
    OBJECT IDENTIFIER ::= { mplsTeExtConformance 2 }
  1. - Compliance requirement for fully compliant implementations.
 mplsTeExtModuleFullCompliance MODULE-COMPLIANCE
    STATUS current
    DESCRIPTION
         "Compliance statement for agents that provide full
          support the MPLS-TE-EXT-STD-MIB module."
    MODULE -- this module
  1. - The mandatory group has to be implemented by all
  2. - LSRs that originate/terminate MPLS-TP Tunnels.
  3. - In addition, depending on the type of tunnels
  4. - supported, other groups become mandatory as
  5. - explained below.
       MANDATORY-GROUPS    {
          mplsTunnelExtGroup
       }
       GROUP mplsTunnelExtIpOperatorGroup
       DESCRIPTION
           "This group is mandatory for devices that support
            configuration of IP-based identifier tunnels."
       GROUP mplsTunnelExtIccOperatorGroup
       DESCRIPTION
           "This group is mandatory for devices that support
            configuration of ICC based tunnels."
        ::= { mplsTeExtCompliances 1 }

Venkatesan, et al. Standards Track [Page 53] RFC 7453 MPLS-TP MIB February 2015

  1. - Compliance requirement for read-only implementations.
 mplsTeExtModuleReadOnlyCompliance MODULE-COMPLIANCE
    STATUS current
    DESCRIPTION
        "Compliance statement for agents that only provide
         read-only support for the MPLS-TE-EXT-STD-MIB module."
    MODULE -- this module
 MANDATORY-GROUPS    {
    mplsTunnelExtGroup
 }
 GROUP mplsTunnelExtIpOperatorGroup
 DESCRIPTION
     "This group is mandatory for devices that support
      configuration of IP-based identifier tunnels."
 GROUP mplsTunnelExtIccOperatorGroup
 DESCRIPTION
     "This group is mandatory for devices that support
      configuration of ICC-based tunnels."
  1. - mplsTunnelExtTable
 OBJECT      mplsTunnelExtOppositeDirPtr
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtOppositeDirTnlValid
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtDestTnlIndex
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtDestTnlLspIndex
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."

Venkatesan, et al. Standards Track [Page 54] RFC 7453 MPLS-TP MIB February 2015

 OBJECT      mplsTunnelExtDestTnlValid
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtIngressLSRLocalIdValid
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtEgressLSRLocalIdValid
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigGlobalId
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigNodeId
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigStorageType
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigRowStatus
 SYNTAX      RowStatus { active(1) }
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigCcId
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
 OBJECT      mplsTunnelExtNodeConfigIccId
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."

Venkatesan, et al. Standards Track [Page 55] RFC 7453 MPLS-TP MIB February 2015

 OBJECT      mplsTunnelExtNodeConfigIccValid
 MIN-ACCESS  read-only
 DESCRIPTION
       "Write access is not required."
      ::= { mplsTeExtCompliances 2 }
  1. - Units of conformance.
   mplsTunnelExtGroup OBJECT-GROUP
      OBJECTS {
        mplsTunnelExtOppositeDirPtr,
        mplsTunnelExtOppositeDirTnlValid,
        mplsTunnelExtDestTnlIndex,
        mplsTunnelExtDestTnlLspIndex,
        mplsTunnelExtDestTnlValid,
        mplsTunnelExtIngressLSRLocalIdValid,
        mplsTunnelExtEgressLSRLocalIdValid
     }
    STATUS  current
    DESCRIPTION
         "Necessary, but not sufficient, set of objects to
           implement tunnels.  In addition, depending on the
           operating environment, the following groups are
           mandatory."
    ::= { mplsTeExtGroups 1 }
 mplsTunnelExtIpOperatorGroup  OBJECT-GROUP
    OBJECTS { mplsTunnelExtNodeConfigLocalIdNext,
              mplsTunnelExtNodeConfigGlobalId,
              mplsTunnelExtNodeConfigNodeId,
              mplsTunnelExtNodeIpMapLocalId,
              mplsTunnelExtNodeConfigStorageType,
              mplsTunnelExtNodeConfigRowStatus
    }
    STATUS  current
    DESCRIPTION
         "Object(s) needed to implement IP-compatible tunnels."
    ::= { mplsTeExtGroups 2 }
 mplsTunnelExtIccOperatorGroup  OBJECT-GROUP
    OBJECTS { mplsTunnelExtNodeConfigLocalIdNext,
              mplsTunnelExtNodeConfigCcId,
              mplsTunnelExtNodeConfigIccId,
              mplsTunnelExtNodeConfigNodeId,
              mplsTunnelExtNodeConfigIccValid,
              mplsTunnelExtNodeIccMapLocalId,

Venkatesan, et al. Standards Track [Page 56] RFC 7453 MPLS-TP MIB February 2015

              mplsTunnelExtNodeConfigStorageType,
              mplsTunnelExtNodeConfigRowStatus
    }
    STATUS  current
    DESCRIPTION
         "Object(s) needed to implement ICC-based tunnels."
    ::= { mplsTeExtGroups 3 }
  1. - MPLS-TE-EXT-STD-MIB module ends

END

14. Security Considerations

 This document follows the security considerations mentioned in
 Section 12 of [RFC3812].  These security considerations are also
 applicable to the MIB objects and tables defined in this document,
 which are identified as below.
  1. The common objects mplsIdGlobalId, mplsIdNodeId, mplsIdCc, and

mplsIdIcc are used to define the identity of an MPLS-TP node for

      OAM purposes.  If write-access is allowed to these objects it
      offers the possibility for incorrect values to be entered that
      will confuse the information returned by OAM functions and
      possibly prevent OAM from operating correctly.  Furthermore,
      there is the possibility of inducing one node to impersonate
      another with confusing results.
  1. mplsTunnelExtNodeConfigTable, mplsTunnelExtTable and

mplsXCExtTable collectively contain objects to provision MPLS-TP

      Tunnels, tunnel hops, and tunnel resources.
 Some of the readable objects in this MIB module (i.e., objects with a
 MAX-ACCESS other than not-accessible) may be considered sensitive or
 vulnerable in some network environments.  It is thus important to
 control even GET and/or NOTIFY access to these objects and possibly
 to even encrypt the values of these objects when sending them over
 the network via SNMP.  These are the tables and objects and their
 sensitivity/vulnerability:
  1. mplsTunnelExtNodeConfigTable, mplsTunnelExtTable, and

mplsXCExtTable collectively show the characteristics of the

      MPLS-TP tunnel network topology.  If an Administrator does not
      want to reveal this information, then these tables should be
      considered sensitive/vulnerable.
 SNMP versions prior to SNMPv3 did not include adequate security.
 Even if the network itself is secure (for example by using IPsec),
 there is no control as to who on the secure network is allowed to

Venkatesan, et al. Standards Track [Page 57] RFC 7453 MPLS-TP MIB February 2015

 access and GET/SET (read/change/create/delete) the objects in this
 MIB module.
 Implementations SHOULD provide the security features described by the
 SNMPv3 framework (see [RFC3410]), and implementations claiming
 compliance to the SNMPv3 standard MUST include full support for
 authentication and privacy via the User-based Security Model (USM)
 [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
 MAY also provide support for the Transport Security Model (TSM)
 [RFC5591] in combination with a secure transport such as SSH
 [RFC5592] or TLS/DTLS [RFC6353].
 Further, deployment of SNMP versions prior to SNMPv3 is NOT
 RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
 enable cryptographic security.  It is then a customer/operator
 responsibility to ensure that the SNMP entity giving access to an
 instance of this MIB module is properly configured to give access to
 the objects only to those principals (users) that have legitimate
 rights to indeed GET or SET (change/create/delete) them.

15. IANA Considerations

 As described in [RFC4221] and [RFC6639], and as requested in the
 MPLS-TC-STD-MIB [RFC3811], MPLS-related Standards Track MIB modules
 should be rooted under the mplsStdMIB subtree.  There are four MPLS
 MIB modules contained in this document; each of the following
 subsections lists a new assignment made by IANA under the mplsStdMIB
 subtree.  New assignments can only be made via a Standards Action as
 specified in [RFC5226].

15.1. IANA Considerations for MPLS-TC-EXT-STD-MIB

 IANA has assigned the OID { mplsStdMIB 17 } to the
 MPLS-TC-EXT-STD-MIB module specified in this document.

15.2. IANA Considerations for MPLS-ID-STD-MIB

 IANA has assigned the OID { mplsStdMIB 18 } to the MPLS-ID-STD-MIB
 module specified in this document.

15.3. IANA Considerations for MPLS-LSR-EXT-STD-MIB

 IANA has assigned the OID { mplsStdMIB 19 } to the
 MPLS-LSR-EXT-STD-MIB module specified in this document.

Venkatesan, et al. Standards Track [Page 58] RFC 7453 MPLS-TP MIB February 2015

15.4. IANA Considerations for MPLS-TE-EXT-STD-MIB

 IANA has assigned the OID { mplsStdMIB 20 } to the
 MPLS-TE-EXT-STD-MIB module specified in this document.

16. References

16.1. Normative References

 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119, March 1997,
            <http://www.rfc-editor.org/info/rfc2119>.
 [RFC2578]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
            Schoenwaelder, Ed., "Structure of Management Information
            Version 2 (SMIv2)", STD 58, RFC 2578, April 1999,
            <http://www.rfc-editor.org/info/rfc2578>.
 [RFC2579]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
            Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
            58, RFC 2579, April 1999,
            <http://www.rfc-editor.org/info/rfc2579>.
 [RFC2580]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
            Schoenwaelder, Ed., "Conformance Statements for SMIv2",
            STD 58, RFC 2580, April 1999,
            <http://www.rfc-editor.org/info/rfc2580>.
 [RFC3031]  Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
            Label Switching Architecture", RFC 3031, January 2001,
            <http://www.rfc-editor.org/info/rfc3031>.
 [RFC3289]  Baker, F., Chan, K., and A. Smith, "Management Information
            Base for the Differentiated Services Architecture", RFC
            3289, May 2002, <http://www.rfc-editor.org/info/rfc3289>.
 [RFC3811]  Nadeau, T., Ed., and J. Cucchiara, Ed., "Definitions of
            Textual Conventions (TCs) for Multiprotocol Label
            Switching (MPLS) Management", RFC 3811, June 2004,
            <http://www.rfc-editor.org/info/rfc3811>.
 [RFC3812]  Srinivasan, C., Viswanathan, A., and T. Nadeau,
            "Multiprotocol Label Switching (MPLS) Traffic Engineering
            (TE) Management Information Base (MIB)", RFC 3812, June
            2004, <http://www.rfc-editor.org/info/rfc3812>.

Venkatesan, et al. Standards Track [Page 59] RFC 7453 MPLS-TP MIB February 2015

 [RFC3813]  Srinivasan, C., Viswanathan, A., and T. Nadeau,
            "Multiprotocol Label Switching (MPLS) Label Switching
            Router (LSR) Management Information Base (MIB)", RFC 3813,
            June 2004, <http://www.rfc-editor.org/info/rfc3813>.
 [RFC4802]  Nadeau, T., Ed., and A. Farrel, Ed., "Generalized
            Multiprotocol Label Switching (GMPLS) Traffic Engineering
            Management Information Base", RFC 4802, February 2007,
            <http://www.rfc-editor.org/info/rfc4802>.
 [RFC6370]  Bocci, M., Swallow, G., and E. Gray, "MPLS Transport
            Profile (MPLS-TP) Identifiers", RFC 6370, September 2011,
            <http://www.rfc-editor.org/info/rfc6370>.
 [RFC6923]  Winter, R., Gray, E., van Helvoort, H., and M. Betts,
            "MPLS Transport Profile (MPLS-TP) Identifiers Following
            ITU-T Conventions", RFC 6923, May 2013,
            <http://www.rfc-editor.org/info/rfc6923>.
 [T.50]     ITU-T, "International Reference Alphabet (IRA) (Formerly
            International Alphabet No. 5 or IA5) - Information
            technology - 7-bit coded character set for information
            exchange", ITU-T Recommendation T.50, September 1992.

16.2. Informative References

 [RFC3410]  Case, J., Mundy, R., Partain, D., and B. Stewart,
            "Introduction and Applicability Statements for Internet-
            Standard Management Framework", RFC 3410, December 2002,
            <http://www.rfc-editor.org/info/rfc3410>.
 [RFC3414]  Blumenthal, U. and B. Wijnen, "User-based Security Model
            (USM) for version 3 of the Simple Network Management
            Protocol (SNMPv3)", STD 62, RFC 3414, December 2002,
            <http://www.rfc-editor.org/info/rfc3414>.
 [RFC3826]  Blumenthal, U., Maino, F., and K. McCloghrie, "The
            Advanced Encryption Standard (AES) Cipher Algorithm in the
            SNMP User-based Security Model", RFC 3826, June 2004,
            <http://www.rfc-editor.org/info/rfc3826>.
 [RFC4221]  Nadeau, T., Srinivasan, C., and A. Farrel, "Multiprotocol
            Label Switching (MPLS) Management Overview", RFC 4221,
            November 2005, <http://www.rfc-editor.org/info/rfc4221>.
 [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
            IANA Considerations Section in RFCs", BCP 26, RFC 5226,
            May 2008, <http://www.rfc-editor.org/info/rfc5226>.

Venkatesan, et al. Standards Track [Page 60] RFC 7453 MPLS-TP MIB February 2015

 [RFC5591]  Harrington, D. and W. Hardaker, "Transport Security Model
            for the Simple Network Management Protocol (SNMP)", STD
            78, RFC 5591, June 2009,
            <http://www.rfc-editor.org/info/rfc5591>.
 [RFC5592]  Harrington, D., Salowey, J., and W. Hardaker, "Secure
            Shell Transport Model for the Simple Network Management
            Protocol (SNMP)", RFC 5592, June 2009,
            <http://www.rfc-editor.org/info/rfc5592>.
 [RFC5654]  Niven-Jenkins, B., Ed., Brungard, D., Ed., Betts, M., Ed.,
            Sprecher, N., and S. Ueno, "Requirements of an MPLS
            Transport Profile", RFC 5654, September 2009,
            <http://www.rfc-editor.org/info/rfc5654>.
 [RFC6353]  Hardaker, W., "Transport Layer Security (TLS) Transport
            Model for the Simple Network Management Protocol (SNMP)",
            STD 78, RFC 6353, July 2011,
            <http://www.rfc-editor.org/info/rfc6353>.
 [RFC6639]  King, D., Ed., and M. Venkatesan, Ed., "Multiprotocol
            Label Switching Transport Profile (MPLS-TP) MIB-Based
            Management Overview", RFC 6639, June 2012,
            <http://www.rfc-editor.org/info/rfc6639>.

Venkatesan, et al. Standards Track [Page 61] RFC 7453 MPLS-TP MIB February 2015

Acknowledgments

 The authors would like to thank Francesco Fondelli, Josh Littlefield,
 Agrahara Kiran Koushik, Metrri Jain, Muly Ilan, Randy Presuhn, Elwyn
 Davies, Tom Taylor, and Pete Resnick for their valuable reviews and
 comments.  A special thanks to Joan Cucchiara and Adrian Farrel for
 really getting the MIB modules into shape.

Authors' Addresses

 Venkatesan Mahalingam
 Dell Inc.
 5450 Great America Parkway,
 Santa Clara, CA 95054
 United States
 EMail: venkat.mahalingams@gmail.com
 Sam Aldrin
 Huawei Technologies
 2330 Central Express Way,
 Santa Clara, CA 95051
 United States
 EMail:  aldrin.ietf@gmail.com
 Thomas D. Nadeau
 Brocade
 EMail: tnadeau@lucidvision.com
 Kannan KV Sampath
 Redeem
 India
 EMail: kannankvs@gmail.com

Venkatesan, et al. Standards Track [Page 62]

/data/webs/external/dokuwiki/data/pages/rfc/rfc7453.txt · Last modified: 2015/02/25 22:14 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki