GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc6416

Internet Engineering Task Force (IETF) M. Schmidt Request for Comments: 6416 Dolby Laboratories Obsoletes: 3016 F. de Bont Category: Standards Track Philips Electronics ISSN: 2070-1721 S. Doehla

                                                        Fraunhofer IIS
                                                                J. Kim
                                                   LG Electronics Inc.
                                                          October 2011
         RTP Payload Format for MPEG-4 Audio/Visual Streams

Abstract

 This document describes Real-time Transport Protocol (RTP) payload
 formats for carrying each of MPEG-4 Audio and MPEG-4 Visual
 bitstreams without using MPEG-4 Systems.  This document obsoletes RFC
 3016.  It contains a summary of changes from RFC 3016 and discusses
 backward compatibility to RFC 3016.  It is a necessary revision of
 RFC 3016 in order to correct misalignments with the 3GPP Packet-
 switched Streaming Service (PSS) specification regarding the RTP
 payload format for MPEG-4 Audio.
 For the purpose of directly mapping MPEG-4 Audio/Visual bitstreams
 onto RTP packets, this document provides specifications for the use
 of RTP header fields and also specifies fragmentation rules.  It also
 provides specifications for Media Type registration and the use of
 the Session Description Protocol (SDP).  The audio payload format
 described in this document has some limitations related to the
 signaling of audio codec parameters for the required multiplexing
 format.  Therefore, new system designs should utilize RFC 3640, which
 does not have these restrictions.  Nevertheless, this revision of RFC
 3016 is provided to update and complete the specification and to
 enable interoperable implementations.

Status of This Memo

 This is an Internet Standards Track document.
 This document is a product of the Internet Engineering Task Force
 (IETF).  It represents the consensus of the IETF community.  It has
 received public review and has been approved for publication by the
 Internet Engineering Steering Group (IESG).  Further information on
 Internet Standards is available in Section 2 of RFC 5741.

Schmidt, et al. Standards Track [Page 1] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 Information about the current status of this document, any errata,
 and how to provide feedback on it may be obtained at
 http://www.rfc-editor.org/info/rfc6416.

Copyright Notice

 Copyright (c) 2011 IETF Trust and the persons identified as the
 document authors.  All rights reserved.
 This document is subject to BCP 78 and the IETF Trust's Legal
 Provisions Relating to IETF Documents
 (http://trustee.ietf.org/license-info) in effect on the date of
 publication of this document.  Please review these documents
 carefully, as they describe your rights and restrictions with respect
 to this document.  Code Components extracted from this document must
 include Simplified BSD License text as described in Section 4.e of
 the Trust Legal Provisions and are provided without warranty as
 described in the Simplified BSD License.
 This document may contain material from IETF Documents or IETF
 Contributions published or made publicly available before November
 10, 2008.  The person(s) controlling the copyright in some of this
 material may not have granted the IETF Trust the right to allow
 modifications of such material outside the IETF Standards Process.
 Without obtaining an adequate license from the person(s) controlling
 the copyright in such materials, this document may not be modified
 outside the IETF Standards Process, and derivative works of it may
 not be created outside the IETF Standards Process, except to format
 it for publication as an RFC or to translate it into languages other
 than English.

Schmidt, et al. Standards Track [Page 2] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

Table of Contents

 1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
   1.1.  MPEG-4 Visual RTP Payload Format . . . . . . . . . . . . .  4
   1.2.  MPEG-4 Audio RTP Payload Format  . . . . . . . . . . . . .  5
   1.3.  Interoperability with RFC 3016 . . . . . . . . . . . . . .  6
   1.4.  Relation with RFC 3640 . . . . . . . . . . . . . . . . . .  6
 2.  Definitions and Abbreviations  . . . . . . . . . . . . . . . .  6
 3.  Clarifications on Specifying Codec Configurations for
     MPEG-4 Audio . . . . . . . . . . . . . . . . . . . . . . . . .  7
 4.  LATM Restrictions for RTP Packetization of MPEG-4 Audio
     Bitstreams . . . . . . . . . . . . . . . . . . . . . . . . . .  7
 5.  RTP Packetization of MPEG-4 Visual Bitstreams  . . . . . . . .  8
   5.1.  Use of RTP Header Fields for MPEG-4 Visual . . . . . . . .  9
   5.2.  Fragmentation of MPEG-4 Visual Bitstream . . . . . . . . . 10
   5.3.  Examples of Packetized MPEG-4 Visual Bitstream . . . . . . 11
 6.  RTP Packetization of MPEG-4 Audio Bitstreams . . . . . . . . . 15
   6.1.  RTP Packet Format  . . . . . . . . . . . . . . . . . . . . 15
   6.2.  Use of RTP Header Fields for MPEG-4 Audio  . . . . . . . . 16
   6.3.  Fragmentation of MPEG-4 Audio Bitstream  . . . . . . . . . 17
 7.  Media Type Registration for MPEG-4 Audio/Visual Streams  . . . 17
   7.1.  Media Type Registration for MPEG-4 Visual  . . . . . . . . 17
   7.2.  Mapping to SDP for MPEG-4 Visual . . . . . . . . . . . . . 20
     7.2.1.  Declarative SDP Usage for MPEG-4 Visual  . . . . . . . 20
   7.3.  Media Type Registration for MPEG-4 Audio . . . . . . . . . 21
   7.4.  Mapping to SDP for MPEG-4 Audio  . . . . . . . . . . . . . 24
     7.4.1.  Declarative SDP Usage for MPEG-4 Audio . . . . . . . . 25
       7.4.1.1.  Example: In-Band Configuration . . . . . . . . . . 25
       7.4.1.2.  Example: 6 kbit/s CELP . . . . . . . . . . . . . . 25
       7.4.1.3.  Example: 64 kbit/s AAC LC Stereo . . . . . . . . . 26
       7.4.1.4.  Example: Use of the "SBR-enabled" Parameter  . . . 26
       7.4.1.5.  Example: Hierarchical Signaling of SBR . . . . . . 27
       7.4.1.6.  Example: HE AAC v2 Signaling . . . . . . . . . . . 27
       7.4.1.7.  Example: Hierarchical Signaling of PS  . . . . . . 28
       7.4.1.8.  Example: MPEG Surround . . . . . . . . . . . . . . 28
       7.4.1.9.  Example: MPEG Surround with Extended SDP
                 Parameters . . . . . . . . . . . . . . . . . . . . 28
       7.4.1.10. Example: MPEG Surround with Single-Layer
                 Configuration  . . . . . . . . . . . . . . . . . . 29
 8.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 29
 9.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 30
 10. Security Considerations  . . . . . . . . . . . . . . . . . . . 30
 11. Differences to RFC 3016  . . . . . . . . . . . . . . . . . . . 31
 12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 32
   12.1. Normative References . . . . . . . . . . . . . . . . . . . 32
   12.2. Informative References . . . . . . . . . . . . . . . . . . 33

Schmidt, et al. Standards Track [Page 3] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

1. Introduction

 The RTP payload formats described in this document specify how MPEG-4
 Audio [14496-3] and MPEG-4 Visual streams [14496-2] are to be
 fragmented and mapped directly onto RTP packets.
 These RTP payload formats enable transport of MPEG-4 Audio/Visual
 streams without using the synchronization and stream management
 functionality of MPEG-4 Systems [14496-1].  Such RTP payload formats
 will be used in systems that have intrinsic stream management
 functionality and thus require no such functionality from MPEG-4
 Systems.  H.323 [H323] terminals are an example of such systems,
 where MPEG-4 Audio/Visual streams are not managed by MPEG-4 Systems
 Object Descriptors but by H.245 [H245].  The streams are directly
 mapped onto RTP packets without using the MPEG-4 Systems Sync Layer.
 Other examples are the Session Initiation Protocol (SIP) [RFC3261]
 and Real Time Streaming Protocol (RTSP) where media type and SDP are
 used.  Media type and SDP usages of the RTP payload formats described
 in this document are defined to directly specify the attribute of
 Audio/Visual streams (e.g., media type, packetization format, and
 codec configuration) without using MPEG-4 Systems.  The obvious
 benefit is that these MPEG-4 Audio/Visual RTP payload formats can be
 handled in a unified way together with those formats defined for non-
 MPEG-4 codecs.  The disadvantage is that interoperability with
 environments using MPEG-4 Systems may be difficult; hence, other
 payload formats may be better suited to those applications.
 The semantics of RTP headers in such cases need to be clearly
 defined, including the association with MPEG-4 Audio/Visual data
 elements.  In addition, it is beneficial to define the fragmentation
 rules of RTP packets for MPEG-4 Video streams so as to enhance error
 resiliency by utilizing the error resiliency tools provided inside
 the MPEG-4 Video stream.

1.1. MPEG-4 Visual RTP Payload Format

 MPEG-4 Visual is a visual coding standard with many features,
 including: high coding efficiency; high error resiliency; and
 multiple, arbitrary shape object-based coding [14496-2].  It covers a
 wide range of bitrates from scores of kbit/s to several Mbit/s.  It
 also covers a wide variety of networks, ranging from those guaranteed
 to be almost error-free to mobile networks with high error rates.
 With respect to the fragmentation rules for an MPEG-4 Visual
 bitstream defined in this document, since MPEG-4 Visual is used for a
 wide variety of networks, it is desirable not to apply too much
 restriction on fragmentation, and a fragmentation rule such as "a
 single video packet shall always be mapped on a single RTP packet"

Schmidt, et al. Standards Track [Page 4] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 may be inappropriate.  On the other hand, careless, media-unaware
 fragmentation may cause degradation in error resiliency and bandwidth
 efficiency.  The fragmentation rules described in this document are
 flexible but manage to define the minimum rules for preventing
 meaningless fragmentation while utilizing the error resiliency
 functionalities of MPEG-4 Visual.
 The fragmentation rule "Different Video Object Planes (VOPs) SHOULD
 be fragmented into different RTP packets" is made so that the RTP
 timestamp uniquely indicates the VOP time framing.  On the other
 hand, MPEG-4 video may generate VOPs of very small size, in cases
 with an empty VOP (vop_coded=0) containing only VOP header or an
 arbitrary shaped VOP with a small number of coding blocks.  To reduce
 the overhead for such cases, the fragmentation rule permits
 concatenating multiple VOPs in an RTP packet.  (See fragmentation
 rule (4) in Section 5.2 and the descriptions of marker bit and
 timestamp in Section 5.1.)
 While the additional media-specific RTP header defined for such video
 coding tools as H.261 [H261] or MPEG-1/2 is effective in helping to
 recover picture headers corrupted by packet losses, MPEG-4 Visual
 already has error resiliency functionalities for recovering corrupt
 headers, and these can be used on RTP/IP networks as well as on other
 networks (H.223/mobile, MPEG-2 Transport Stream, etc.).  Therefore,
 no extra RTP header fields are defined in this MPEG-4 Visual RTP
 payload format.

1.2. MPEG-4 Audio RTP Payload Format

 MPEG-4 Audio is an audio standard that integrates many different
 types of audio coding tools.  Low-overhead MPEG-4 Audio Transport
 Multiplex (LATM) manages the sequences of audio data with relatively
 small overhead.  In audio-only applications, then, it is desirable
 for LATM-based MPEG-4 Audio bitstreams to be directly mapped onto RTP
 packets without using MPEG-4 Systems.
 For MPEG-4 Audio coding tools, as is true for other audio coders, if
 the payload is a single audio frame, packet loss will not impair the
 decodability of adjacent packets.  Therefore, the additional media-
 specific header for recovering errors will not be required for MPEG-4
 Audio.  Existing RTP protection mechanisms, such as Generic Forward
 Error Correction [RFC5109] and Redundant Audio Data [RFC2198], MAY be
 applied to improve error resiliency.

Schmidt, et al. Standards Track [Page 5] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

1.3. Interoperability with RFC 3016

 This specification is not backwards compatible with [RFC3016], as a
 binary incompatible LATM version is mandated.  Existing
 implementations of RFC 3016 that use a recent LATM version may
 already comply to this specification and must be considered as not
 compliant with RFC 3016.  The 3GPP PSS service [3GPP] is such an
 example, as a more recent LATM version is mandated in the 3GPP PSS
 specification.  Existing implementations that use the LATM version as
 specified in RFC 3016 MUST be updated to comply with this
 specification.

1.4. Relation with RFC 3640

 In this document a payload format for the transport of MPEG-4
 Elementary Streams is specified.  For MPEG-4 Audio streams "out-of-
 band" signaling is defined such that a receiver is not obliged to
 decode the payload data to determine the audio codec and its
 configuration.  The signaling capabilities specified in this document
 are less explicit than those defined in [RFC3640].  But, the use of
 the MPEG-4 LATM in various transmission standards justifies its right
 to exist; see also Section 1.2.

2. Definitions and Abbreviations

 This document makes use of terms, specified in [14496-2], [14496-3],
 and [23003-1].  In addition, the following terms are used in this
 document and have specific meaning within the context of this
 document.
 Abbreviations:
    AAC: Advanced Audio Coding
    ASC: AudioSpecificConfig
    HE AAC: High Efficiency AAC
    LATM: Low-overhead MPEG-4 Audio Transport Multiplex
    PS: Parametric Stereo
    SBR: Spectral Band Replication
    VOP: Video Object Plane

Schmidt, et al. Standards Track [Page 6] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in [RFC2119].

3. Clarifications on Specifying Codec Configurations for MPEG-4 Audio

 For MPEG-4 Audio [14496-3] streams, the decoder output configuration
 can differ from the core codec configuration depending of use of the
 SBR and PS tools.
 The core codec sampling rate is the default audio codec sampling
 rate.  When SBR is used, typically the double value of the core codec
 sampling rate will be regarded as the definitive sampling rate (i.e.,
 the decoder's output sampling rate)
 Note: The exception is down-sampled SBR mode, in which case the SBR
 sampling rate and core codec sampling rate are identical.
 The core codec channel configuration is the default audio codec
 channel configuration.  When PS is used, the core codec channel
 configuration indicates one channel (i.e., mono) whereas the
 definitive channel configuration is two channels (i.e. stereo).  When
 MPEG Surround is used, the definitive channel configuration depends
 on the output of the MPEG Surround decoder.

4. LATM Restrictions for RTP Packetization of MPEG-4 Audio Bitstreams

 LATM has several multiplexing features as follows:
 o  carrying configuration information with audio data,
 o  concatenating multiple audio frames in one audio stream,
 o  multiplexing multiple objects (programs), and
 o  multiplexing scalable layers,
 However, in RTP transmission, there is no need for the last two
 features.  Therefore, these two features MUST NOT be used in
 applications based on RTP packetization specified by this document.
 Since LATM has been developed for only natural audio coding tools,
 i.e., not for synthesis tools, it seems difficult to transmit
 Structured Audio (SA) data and Text-to-Speech Interface (TTSI) data
 by LATM.  Therefore, SA data and TTSI data MUST NOT be transported by
 the RTP packetization in this document.

Schmidt, et al. Standards Track [Page 7] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 For transmission of scalable streams, audio data of each layer SHOULD
 be packetized onto different RTP streams allowing for the different
 layers to be treated differently at the IP level, for example, via
 some means of differentiated service.  On the other hand, all
 configuration data of the scalable streams are contained in one LATM
 configuration data "StreamMuxConfig", and every scalable layer shares
 the StreamMuxConfig.  The mapping between each layer and its
 configuration data is achieved by LATM header information attached to
 the audio data.  In order to indicate the dependency information of
 the scalable streams, the signaling mechanism as specified in
 [RFC5583] SHOULD be used (see Section 6.2).

5. RTP Packetization of MPEG-4 Visual Bitstreams

 This section specifies RTP packetization rules for MPEG-4 Visual
 content.  An MPEG-4 Visual bitstream is mapped directly onto RTP
 packets without the addition of extra header fields or any removal of
 Visual syntax elements.  The Combined Configuration/Elementary stream
 mode MUST be used so that configuration information will be carried
 to the same RTP port as the elementary stream.  (See Subclause 6.2.1,
 "Start codes", of [14496-2].)  The configuration information MAY
 additionally be specified by some out-of-band means.  If needed by
 systems using media type parameters and SDP parameters, e.g., SIP and
 RTSP, the optional parameter "config" MUST be used to specify the
 configuration information (see Sections 7.1 and 7.2).
 When the short video header mode is used, the RTP payload format for
 H.263 SHOULD be used.  (The format defined in [RFC4629] is
 RECOMMENDED, but the [RFC4628] format MAY be used for compatibility
 with older implementations.)

Schmidt, et al. Standards Track [Page 8] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

V=2PX CC M PT sequence number

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

timestamp

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

synchronization source (SSRC) identifier

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+

contributing source (CSRC) identifiers
….

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+

MPEG-4 Visual stream (byte aligned)
:…OPTIONAL RTP padding

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 1: An RTP Packet for MPEG-4 Visual Stream

5.1. Use of RTP Header Fields for MPEG-4 Visual

 Payload Type (PT): The assignment of an RTP payload type for this
 packet format is outside the scope of this document and will not be
 specified here.  It is expected that the RTP profile for a particular
 class of applications will assign a payload type for this encoding,
 or if that is not done, then a payload type in the dynamic range
 SHALL be chosen by means of an out-of-band signaling protocol (e.g.,
 H.245, SIP).
 Extension (X) bit: Defined by the RTP profile used.
 Sequence Number: Incremented by 1 for each RTP data packet sent,
 starting, for security reasons, with a random initial value.
 Marker (M) bit: The marker bit is set to 1 to indicate the last RTP
 packet (or only RTP packet) of a VOP.  When multiple VOPs are carried
 in the same RTP packet, the marker bit is set to 1.
 Timestamp: The timestamp indicates the sampling instance of the VOP
 contained in the RTP packet.  A constant offset, which is random, is
 added for security reasons.

Schmidt, et al. Standards Track [Page 9] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 o  When multiple VOPs are carried in the same RTP packet, the
    timestamp indicates the earliest of the VOP times within the VOPs
    carried in the RTP packet.  Timestamp information of the rest of
    the VOPs is derived from the timestamp fields in the VOP header
    (modulo_time_base and vop_time_increment).
 o  If the RTP packet contains only configuration information and/or
    Group_of_VideoObjectPlane() fields, the timestamp of the next VOP
    in the coding order is used.
 o  If the RTP packet contains only visual_object_sequence_end_code
    information, the timestamp of the immediately preceding VOP in the
    coding order is used.
 The resolution of the timestamp is set to its default value of 90
 kHz, unless specified by out-of-band means (e.g., SDP parameter or
 media type parameter as defined in Section 7).
 Other header fields are used as described in [RFC3550].

5.2. Fragmentation of MPEG-4 Visual Bitstream

 A fragmented MPEG-4 Visual bitstream is mapped directly onto the RTP
 payload without any addition of extra header fields or any removal of
 Visual syntax elements.
 In the following, header means one of the following:
 o  Configuration information (Visual Object Sequence Header, Visual
    Object Header, and Video Object Layer Header)
 o  visual_object_sequence_end_code
 o  The header of the entry point function for an elementary stream
    (Group_of_VideoObjectPlane() or the header of VideoObjectPlane(),
    video_plane_with_short_header(), MeshObject(), or FaceObject())
 o  The video packet header (video_packet_header() excluding
    next_resync_marker())
 o  The header of gob_layer()
 o  See Subclause 6.2.1 ("Start codes") of [14496-2] for the
    definition of the configuration information and the entry point
    functions.

Schmidt, et al. Standards Track [Page 10] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 The Combined Configuration/Elementary streams mode is used.  The
 following rules apply for the fragmentation.
 (1)  Configuration information and Group_of_VideoObjectPlane() fields
      SHALL be placed at the beginning of the RTP payload (just after
      the RTP header) or just after the header of the syntactically
      upper-layer function.
 (2)  If one or more headers exist in the RTP payload, the RTP payload
      SHALL begin with the header of the syntactically highest
      function.  Note: The visual_object_sequence_end_code is regarded
      as the lowest function.
 (3)  A header SHALL NOT be split into a plurality of RTP packets.
 (4)  Different VOPs SHOULD be fragmented into different RTP packets
      so that one RTP packet consists of the data bytes associated
      with a unique VOP time instance (that is indicated in the
      timestamp field in the RTP packet header), with the exception
      that multiple consecutive VOPs MAY be carried within one RTP
      packet in the decoding order if the size of the VOPs is small.
      Note: When multiple VOPs are carried in one RTP payload, the
      timestamp of the VOPs after the first one may be calculated by
      the decoder.  This operation is necessary only for RTP packets
      in which the marker bit equals to 1 and the beginning of the RTP
      payload corresponds to a start code.  (See the descriptions of
      timestamp and marker bit in Section 5.1.)
 (5)  It is RECOMMENDED that a single video packet is sent as a single
      RTP packet.  The size of a video packet SHOULD be adjusted in
      such a way that the resulting RTP packet is not larger than the
      Path MTU.  If the video packet is disabled by the coder
      configuration (by setting resync_marker_disable in the VOL
      header to 1), or in coding tools where the video packet is not
      supported, a VOP MAY be split at arbitrary byte positions.
      The video packet starts with the VOP header or the video packet
      header, followed by motion_shape_texture(), and ends with
      next_resync_marker() or next_start_code().

5.3. Examples of Packetized MPEG-4 Visual Bitstream

 Figure 2 shows examples of RTP packets generated based on the
 criteria described in Section 5.2

Schmidt, et al. Standards Track [Page 11] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 (a) is an example of the first RTP packet or the random access point
 of an MPEG-4 Visual bitstream containing the configuration
 information.  According to criterion (1), the Visual Object Sequence
 Header (VS header) is placed at the beginning of the RTP payload,
 preceding the Visual Object Header and the Video Object Layer Header
 (VO header, VOL header).  Since the fragmentation rule defined in
 Section 5.2 guarantees that the configuration information, starting
 with visual_object_sequence_start_code, is always placed at the
 beginning of the RTP payload, RTP receivers can detect the random
 access point by checking if the first 32-bit field of the RTP payload
 is visual_object_sequence_start_code.
 (b) is another example of the RTP packet containing the configuration
 information.  It differs from example (a) in that the RTP packet also
 contains a VOP header and a video packet in the VOP following the
 configuration information.  Since the length of the configuration
 information is relatively short (typically scores of bytes) and an
 RTP packet containing only the configuration information may thus
 increase the overhead, the configuration information and the
 subsequent VOP can be packetized into a single RTP packet.
 (c) is an example of an RTP packet that contains
 Group_of_VideoObjectPlane (GOV).  Following criterion (1), the GOV is
 placed at the beginning of the RTP payload.  It would be a waste of
 RTP/IP header overhead to generate an RTP packet containing only a
 GOV whose length is 7 bytes.  Therefore, the following VOP (or a part
 of it) can be placed in the same RTP packet as shown in (c).
 (d) is an example of the case where one video packet is packetized
 into one RTP packet.  When the packet-loss rate of the underlying
 network is high, this kind of packetization is recommended.  Even
 when the RTP packet containing the VOP header is discarded by a
 packet loss, the other RTP packets can be decoded by using the HEC
 (Header Extension Code) information in the video packet header.  No
 extra RTP header field is necessary.
 (e) is an example of the case where more than one video packet is
 packetized into one RTP packet.  This kind of packetization is
 effective to save the overhead of RTP/IP headers when the bitrate of
 the underlying network is low.  However, it will decrease the packet-
 loss resiliency because multiple video packets are discarded by a
 single RTP packet loss.  The optimal number of video packets in an
 RTP packet and the length of the RTP packet can be determined by
 considering the packet-loss rate and the bitrate of the underlying
 network.

Schmidt, et al. Standards Track [Page 12] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 (f) is an example of the case when the video packet is disabled by
 setting resync_marker_disable in the VOL header to 1.  In this case,
 a VOP may be split into a plurality of RTP packets at arbitrary byte
 positions.  For example, it is possible to split a VOP into fixed-
 length packets.  This kind of coder configuration and RTP packet
 fragmentation may be used when the underlying network is guaranteed
 to be error-free.
 Figure 3 shows examples of RTP packets prohibited by the criteria of
 Section 5.2.
 Fragmentation of a header into multiple RTP packets, as in Figure
 3(a), will not only increase the overhead of RTP/IP headers but also
 decrease the error resiliency.  Therefore, it is prohibited by
 criterion (3).
 When concatenating more than one video packet into an RTP packet, the
 VOP header or video_packet_header() is not allowed to be placed in
 the middle of the RTP payload.  The packetization as in Figure 2(b)
 is not allowed by criterion (2) due to the aspect of the error
 resiliency.  Comparing this example with Figure 2(d), although two
 video packets are mapped onto two RTP packets in both cases, the
 packet-loss resiliency is not identical.  Namely, if the second RTP
 packet is lost, both video packets 1 and 2 are lost in the case of
 Figure 3(b), whereas only video packet 2 is lost in the case of
 Figure 2(d).

Schmidt, et al. Standards Track [Page 13] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

  +------+------+------+------+

(a) | RTP | VS | VO | VOL |

  |header|header|header|header|
  +------+------+------+------+
  +------+------+------+------+------+------------+

(b) | RTP | VS | VO | VOL | VOP |Video Packet|

  |header|header|header|header|header|            |
  +------+------+------+------+------+------------+
  +------+-----+------------------+

© | RTP | GOV |Video Object Plane|

  |header|     |                  |
  +------+-----+------------------+
  +------+------+------------+  +------+------+------------+

(d) | RTP | VOP |Video Packet| | RTP | VP |Video Packet|

  |header|header|    (1)     |  |header|header|    (2)     |
  +------+------+------------+  +------+------+------------+
  +------+------+------------+------+------------+------+------------+

(e) | RTP | VP |Video Packet| VP |Video Packet| VP |Video Packet|

  |header|header|     (1)    |header|    (2)     |header|    (3)     |
  +------+------+------------+------+------------+------+------------+
  +------+------+------------+  +------+------------+

(f) | RTP | VOP |VOP fragment| | RTP |VOP fragment|

  |header|header|    (1)     |  |header|    (2)     | . . .
  +------+------+------------+  +------+------------+
     Figure 2: Examples of RTP Packetized MPEG-4 Visual Bitstream
    +------+-------------+  +------+------------+------------+
(a) | RTP  |First half of|  | RTP  |Last half of|Video Packet|
    |header|  VP header  |  |header|  VP header |            |
    +------+-------------+  +------+------------+------------+
    +------+------+----------+  +------+---------+------+------------+
(b) | RTP  | VOP  |First half|  | RTP  |Last half|  VP  |Video Packet|
    |header|header| of VP(1) |  |header| of VP(1)|header|    (2)     |
    +------+------+----------+  +------+---------+------+------------+
 Figure 3: Examples of Prohibited RTP Packetization for MPEG-4 Visual

Schmidt, et al. Standards Track [Page 14] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

6. RTP Packetization of MPEG-4 Audio Bitstreams

 This section specifies RTP packetization rules for MPEG-4 Audio
 bitstreams.  MPEG-4 Audio streams MUST be formatted LATM (Low-
 overhead MPEG-4 Audio Transport Multiplex) [14496-3] streams, and the
 LATM-based streams are then mapped onto RTP packets as described in
 the sections below.

6.1. RTP Packet Format

 LATM-based streams consist of a sequence of audioMuxElements that
 include one or more PayloadMux elements that carry the audio frames.
 A complete audioMuxElement or a part of one SHALL be mapped directly
 onto an RTP payload without any removal of audioMuxElement syntax
 elements (see Figure 4).  The first byte of each audioMuxElement
 SHALL be located at the first payload location in an RTP packet.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

V=2PX CC M PT sequence number

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

timestamp

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

synchronization source (SSRC) identifier

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+

contributing source (CSRC) identifiers
….

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+

: audioMuxElement (byte aligned) :Payload

:…OPTIONAL RTP padding

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 4 - An RTP packet for MPEG-4 Audio
 In order to decode the audioMuxElement, the following
 muxConfigPresent information is required to be indicated by out-of-
 band means.  When SDP is utilized for this indication, the media type
 parameter "cpresent" corresponds to the muxConfigPresent information
 (see Section 7.3).  The following restrictions apply:

Schmidt, et al. Standards Track [Page 15] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 o  In the out-of-band configuration case, the number of PayloadMux
    elements contained in each audioMuxElement can only be set once.
    If more than one PayloadMux element is contained in each
    audioMuxElement, special care is required to ensure that the last
    RTP packet remains decodable.
 o  To construct the audioMuxElement in the in-band configuration
    case, non-octet-aligned configuration data is inserted immediately
    before the one or more PayloadMux elements.  Since the generation
    of RTP payloads with non-octet-aligned data is not possible with
    RTP hint tracks, as defined by the MP4 file format [14496-12]
    [14496-14], this document does not support RTP hint tracks for the
    in-band configuration case.
 muxConfigPresent: If this value is set to 1 (in-band mode), the
 audioMuxElement SHALL include an indication bit "useSameStreamMux"
 and MAY include the configuration information for audio compression
 "StreamMuxConfig".  The useSameStreamMux bit indicates whether the
 StreamMuxConfig element in the previous frame is applied in the
 current frame.  If the useSameStreamMux bit indicates to use the
 StreamMuxConfig from the previous frame, but if the previous frame
 has been lost, the current frame may not be decodable.  Therefore, in
 case of in-band mode, the StreamMuxConfig element SHOULD be
 transmitted repeatedly depending on the network condition.  On the
 other hand, if muxConfigPresent is set to 0 (out-of-band mode), the
 StreamMuxConfig element is required to be transmitted by an out-of-
 band means.  In case of SDP, the media type parameter "config" is
 utilized (see Section 7.3).

6.2. Use of RTP Header Fields for MPEG-4 Audio

 Payload Type (PT): The assignment of an RTP payload type for this
 packet format is outside the scope of this document and will only be
 restricted here.  It is expected that the RTP profile for a
 particular class of applications will assign a payload type for this
 encoding, or if that is not done, then a payload type in the dynamic
 range shall be chosen by means of an out-of-band signaling protocol
 (e.g., H.245, SIP).  In the dynamic assignment of RTP payload types
 for scalable streams, the server SHALL assign a different value to
 each layer.  The dependency relationships between the enhanced layer
 and the base layer MUST be signaled as specified in [RFC5583].  An
 example of the use of such signaling for scalable audio streams can
 be found in [RFC5691].
 Marker (M) bit: The marker bit indicates audioMuxElement boundaries.
 It is set to 1 to indicate that the RTP packet contains a complete
 audioMuxElement or the last fragment of an audioMuxElement.

Schmidt, et al. Standards Track [Page 16] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 Timestamp: The timestamp indicates the sampling instance of the first
 audio frame contained in the RTP packet.  Timestamps are RECOMMENDED
 to start at a random value for security reasons.
 Unless specified by an out-of-band means, the resolution of the
 timestamp is set to its default value of 90 kHz.
 Sequence Number: Incremented by 1 for each RTP packet sent, starting,
 for security reasons, with a random value.
 Other header fields are used as described in [RFC3550].

6.3. Fragmentation of MPEG-4 Audio Bitstream

 It is RECOMMENDED to put one audioMuxElement in each RTP packet.  If
 the size of an audioMuxElement can be kept small enough that the size
 of the RTP packet containing it does not exceed the size of the Path
 MTU, this will be no problem.  If it cannot, the audioMuxElement
 SHALL be fragmented and spread across multiple packets.

7. Media Type Registration for MPEG-4 Audio/Visual Streams

 The following sections describe the media type registrations for
 MPEG-4 Audio/Visual streams, which are registered in accordance with
 [RFC4855] and use the template of [RFC4288].  Media type registration
 and SDP usage for the MPEG-4 Visual stream are described in Sections
 7.1 and 7.2, respectively, while media type registration and SDP
 usage for MPEG-4 Audio stream are described in Sections 7.3 and 7.4,
 respectively.

7.1. Media Type Registration for MPEG-4 Visual

 The receiver MUST ignore any unspecified parameter in order to ensure
 that additional parameters can be added in any future revision of
 this specification.
 Type name: video
 Subtype name: MP4V-ES
 Required parameters: none
 Optional parameters:
    "rate": This parameter is used only for RTP transport.  It
    indicates the resolution of the timestamp field in the RTP header.
    If this parameter is not specified, its default value of 90000 (90
    kHz) is used.

Schmidt, et al. Standards Track [Page 17] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

    "profile-level-id": A decimal representation of MPEG-4 Visual
    Profile and Level indication value (profile_and_level_indication)
    defined in Table G-1 of [14496-2].  This parameter MAY be used in
    the capability exchange or session setup procedure to indicate the
    MPEG-4 Visual Profile and Level combination of which the MPEG-4
    Visual codec is capable.  If this parameter is not specified by
    the procedure, its default value of 1 (Simple Profile/Level 1) is
    used.
    "config": This parameter SHALL be used to indicate the
    configuration of the corresponding MPEG-4 Visual bitstream.  It
    SHALL NOT be used to indicate the codec capability in the
    capability exchange procedure.  It is a hexadecimal representation
    of an octet string that expresses the MPEG-4 Visual configuration
    information, as defined in Subclause 6.2.1 ("Start codes") of
    [14496-2].  The configuration information is mapped onto the octet
    string most significant bit (MSB) first.  The first bit of the
    configuration information SHALL be located at the MSB of the first
    octet.  The configuration information indicated by this parameter
    SHALL be the same as the configuration information in the
    corresponding MPEG-4 Visual stream, except for
    first_half_vbv_occupancy and latter_half_vbv_occupancy (if they
    exist), which may vary in the repeated configuration information
    inside an MPEG-4 Visual stream.  (See Subclause 6.2.1, "Start
    codes", of [14496-2].)
 Published specification:
    The specifications for MPEG-4 Visual streams are presented in
    [14496-2].  The RTP payload format is described in [RFC6416].
 Encoding considerations:
    Video bitstreams MUST be generated according to MPEG-4 Visual
    specifications [14496-2].  A video bitstream is binary data and
    MUST be encoded for non-binary transport (for email, the Base64
    encoding is sufficient).  This type is also defined for transfer
    via RTP.  The RTP packets MUST be packetized according to the
    MPEG-4 Visual RTP payload format defined in [RFC6416].
 Security considerations:
    See Section 10 of [RFC6416].

Schmidt, et al. Standards Track [Page 18] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 Interoperability considerations:
    MPEG-4 Visual provides a large and rich set of tools for the
    coding of visual objects.  For effective implementation of the
    standard, subsets of the MPEG-4 Visual tool sets have been
    provided for use in specific applications.  These subsets, called
    'Profiles', limit the size of the tool set a decoder is required
    to implement.  In order to restrict computational complexity, one
    or more Levels are set for each Profile.  A Profile@Level
    combination allows:
  • a codec builder to implement only the subset of the standard he

needs, while maintaining interworking with other MPEG-4 devices

       included in the same combination, and
  • checking whether MPEG-4 devices comply with the standard

('conformance testing').

    The visual stream SHALL be compliant with the MPEG-4 Visual
    Profile@Level specified by the parameter "profile-level-id".
    Interoperability between a sender and a receiver may be achieved
    by specifying the parameter "profile-level-id" or by arranging a
    capability exchange/announcement procedure for this parameter.
 Applications that use this media type:
    Audio and visual streaming and conferencing tools
 Additional information: none
 Person and email address to contact for further information:
    See Authors' Addresses section at the end of [RFC6416].
 Intended usage: COMMON
 Author:
    See Authors' Addresses section at the end of [RFC6416].
 Change controller:
    IETF Audio/Video Transport Payloads working group delegated from
    the IESG.

Schmidt, et al. Standards Track [Page 19] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

7.2. Mapping to SDP for MPEG-4 Visual

 The media type video/MP4V-ES string is mapped to fields in SDP
 [RFC4566], as follows:
 o  The media type (video) goes in SDP "m=" as the media name.
 o  The Media subtype (MP4V-ES) goes in SDP "a=rtpmap" as the encoding
    name.
 o  The optional parameter "rate" goes in "a=rtpmap" as the "clock
    rate".
 o  The optional parameter "profile-level-id" and "config" go in the
    "a=fmtp" line to indicate the coder capability and configuration,
    respectively.  These parameters are expressed as a string, in the
    form of a semicolon-separated list of parameter=value pairs.
    Example usages for the "profile-level-id" parameter are:
    1  : MPEG-4 Visual Simple Profile/Level 1
    34 : MPEG-4 Visual Core Profile/Level 2
    145: MPEG-4 Visual Advanced Real Time Simple Profile/Level 1

7.2.1. Declarative SDP Usage for MPEG-4 Visual

 The following are some examples of media representations in SDP:
 Simple Profile/Level 1, rate=90000(90 kHz), "profile-level-id" and
 "config" are present in "a=fmtp" line:
   m=video 49170/2 RTP/AVP 98
   a=rtpmap:98 MP4V-ES/90000
   a=fmtp:98 profile-level-id=1;config=000001B001000001B50900000100000
      00120008440FA282C2090A21F
 Core Profile/Level 2, rate=90000(90 kHz), "profile-level-id" is
 present in "a=fmtp" line:
   m=video 49170/2 RTP/AVP 98
   a=rtpmap:98 MP4V-ES/90000
   a=fmtp:98 profile-level-id=34
 Advance Real Time Simple Profile/Level 1, rate=90000(90 kHz),
 "profile-level-id" is present in "a=fmtp" line:
   m=video 49170/2 RTP/AVP 98
   a=rtpmap:98 MP4V-ES/90000
   a=fmtp:98 profile-level-id=145

Schmidt, et al. Standards Track [Page 20] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

7.3. Media Type Registration for MPEG-4 Audio

 The receiver MUST ignore any unspecified parameter, to ensure that
 additional parameters can be added in any future revision of this
 specification.
 Type name: audio
 Subtype name: MP4A-LATM
 Required parameters:
    "rate": the "rate" parameter indicates the RTP timestamp "clock
    rate".  The default value is 90000.  Other rates MAY be indicated
    only if they are set to the same value as the audio sampling rate
    (number of samples per second).
    In the presence of SBR, the sampling rates for the core encoder/
    decoder and the SBR tool are different in most cases.  Therefore,
    this parameter SHALL NOT be considered as the definitive sampling
    rate.  If this parameter is used, the server must follow the rules
    below:
  • When the presence of SBR is not explicitly signaled by the

optional SDP parameters such as "object", "profile-level-id",

       or "config", this parameter SHALL be set to the core codec
       sampling rate.
  • When the presence of SBR is explicitly signaled by the optional

SDP parameters such as "object", "profile-level-id", or

       "config", this parameter SHALL be set to the SBR sampling rate.
    NOTE: The optional parameter "SBR-enabled" in SDP "a=fmtp" is
    useful for implicit HE AAC / HE AAC v2 signaling.  But the
    "SBR-enabled" parameter can also be used in the case of explicit
    HE AAC / HE AAC v2 signaling.  Therefore, its existence (in
    itself) is not the criteria to determine whether or HE AAC / HE
    AAC v2 signaling is explicit.
 Optional parameters:
    "profile-level-id": a decimal representation of MPEG-4 Audio
    Profile Level indication value defined in [14496-3].  This
    parameter indicates which MPEG-4 Audio tool subsets the decoder is
    capable of using.  If this parameter is not specified in the
    capability exchange or session setup procedure, its default value
    of 30 (Natural Audio Profile/Level 1) is used.

Schmidt, et al. Standards Track [Page 21] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

    "MPS-profile-level-id": a decimal representation of the MPEG
    Surround Profile Level indication as defined in [14496-3].  This
    parameter indicates the support of the MPEG Surround profile and
    level by the decoder to be capable to decode the stream.
    "object": a decimal representation of the MPEG-4 Audio Object Type
    value defined in [14496-3].  This parameter specifies the tool to
    be used by the decoder.  It CAN be used to limit the capability
    within the specified "profile-level-id".
    "bitrate": the data rate for the audio bitstream.
    "cpresent": a boolean parameter that indicates whether audio
    payload configuration data has been multiplexed into an RTP
    payload (see Section 6.1).  A 0 indicates the configuration data
    has not been multiplexed into an RTP payload, and in that case,
    the "config" parameter MUST be present; a 1 indicates that it has
    been multiplexed.  The default if the parameter is omitted is 1.
    If this parameter is set to 1 and the "config" parameter is
    present, the multiplexed configuration data and the value of the
    "config" parameter SHALL be consistent.
    "config": a hexadecimal representation of an octet string that
    expresses the audio payload configuration data "StreamMuxConfig",
    as defined in [14496-3].  Configuration data is mapped onto the
    octet string in an MSB-first basis.  The first bit of the
    configuration data SHALL be located at the MSB of the first octet.
    In the last octet, zero-padding bits, if necessary, SHALL follow
    the configuration data.  Senders MUST set the StreamMuxConfig
    elements taraBufferFullness and latmBufferFullness to their
    largest respective value, indicating that buffer fullness measures
    are not used in SDP.  Receivers MUST ignore the value of these two
    elements contained in the "config" parameter.
    "MPS-asc": a hexadecimal representation of an octet string that
    expresses audio payload configuration data "AudioSpecificConfig",
    as defined in [14496-3].  If this parameter is not present, the
    relevant signaling is performed by other means (e.g., in-band or
    contained in the "config" string).
    The same mapping rules as for the "config" parameter apply.
    "ptime": duration of each packet in milliseconds.

Schmidt, et al. Standards Track [Page 22] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

    "SBR-enabled": a boolean parameter that indicates whether SBR-data
    can be expected in the RTP-payload of a stream.  This parameter is
    relevant for an SBR-capable decoder if the presence of SBR cannot
    be detected from an out-of-band decoder configuration (e.g.,
    contained in the "config" string).
    If this parameter is set to 0, a decoder MAY expect that SBR is
    not used.  If this parameter is set to 1, a decoder CAN up-sample
    the audio data with the SBR tool, regardless of whether or not SBR
    data is present in the stream.
    If the presence of SBR cannot be detected from out-of-band
    configuration and the "SBR-enabled" parameter is not present, the
    parameter defaults to 1 for an SBR-capable decoder.  If the
    resulting output sampling rate or the computational complexity is
    not supported, the SBR tool can be disabled or run in down-sampled
    mode.
    The timestamp resolution at the RTP layer is determined by the
    "rate" parameter.
 Published specification:
    Encoding specifications are provided in [14496-3].  The RTP
    payload format specification is described in [RFC6416].
 Encoding considerations:
    This type is only defined for transfer via RTP.
 Security considerations:
    See Section 10 of [RFC6416].
 Interoperability considerations:
    MPEG-4 Audio provides a large and rich set of tools for the coding
    of audio objects.  For effective implementation of the standard,
    subsets of the MPEG-4 Audio tool sets similar to those used in
    MPEG-4 Visual have been provided (see Section 7.1).
    The audio stream SHALL be compliant with the MPEG-4 Audio Profile@
    Level specified by the parameters "profile-level-id" and
    "MPS-profile-level-id".  Interoperability between a sender and a
    receiver may be achieved by specifying the parameters
    "profile-level-id" and "MPS-profile-level-id" or by arranging in
    the capability exchange procedure to set this parameter mutually

Schmidt, et al. Standards Track [Page 23] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

    to the same value.  Furthermore, the "object" parameter can be
    used to limit the capability within the specified Profile@Level in
    the capability exchange.
 Applications that use this media type:
    Audio and video streaming and conferencing tools.
 Additional information: none
 Personal and email address to contact for further information:
    See Authors' Addresses section at the end of [RFC6416].
 Intended usage: COMMON
 Author:
    See Authors' Addresses section at the end of [RFC6416].
 Change controller:
    IETF Audio/Video Transport Payloads working group delegated from
    the IESG.

7.4. Mapping to SDP for MPEG-4 Audio

 The media type audio/MP4A-LATM string is mapped to fields in SDP
 [RFC4566], as follows:
 o  The media type (audio) goes in SDP "m=" as the media name.
 o  The Media subtype (MP4A-LATM) goes in SDP "a=rtpmap" as the
    encoding name.
 o  The required parameter "rate" goes in "a=rtpmap" as the "clock
    rate".
 o  The optional parameter "ptime" goes in SDP "a=ptime" attribute.
 o  The optional parameters "profile-level-id",
    "MPS-profile-level-id", and "object" go in the "a=fmtp" line to
    indicate the coder capability.

Schmidt, et al. Standards Track [Page 24] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

    The following are some examples of the "profile-level-id" value:
    1 : Main Audio Profile Level 1
    9 : Speech Audio Profile Level 1
    15: High Quality Audio Profile Level 2
    30: Natural Audio Profile Level 1
    44: High Efficiency AAC Profile Level 2
    48: High Efficiency AAC v2 Profile Level 2
    55: Baseline MPEG Surround Profile (see ISO/IEC 23003-1) Level 3
 The optional payload-format-specific parameters "bitrate",
 "cpresent", "config", "MPS-asc", and "SBR-enabled" also go in the
 "a=fmtp" line.  These parameters are expressed as a string, in the
 form of a semicolon-separated list of parameter=value pairs.

7.4.1. Declarative SDP Usage for MPEG-4 Audio

 The following sections contain some examples of the media
 representation in SDP.
 Note that the "a=fmtp" line in some of the examples has been wrapped
 to fit the page; they would comprise a single line in the SDP file.

7.4.1.1. Example: In-Band Configuration

 In this example, the audio configuration data appears in the RTP
 payload exclusively (i.e., the MPEG-4 audio configuration is known
 when a StreamMuxConfig element appears within the RTP payload).
    m=audio 49230 RTP/AVP 96
    a=rtpmap:96 MP4A-LATM/90000
    a=fmtp:96 object=2; cpresent=1
 The "clock rate" is set to 90 kHz.  This is the default value, and
 the real audio sampling rate is known when the audio configuration
 data is received.

7.4.1.2. Example: 6 kbit/s CELP

 This example shows a 6 kbit/s CELP (Code-Excited Linear Prediction)
 bitstream (with an audio sampling rate of 8 kHz).
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/8000
   a=fmtp:96 profile-level-id=9; object=8; cpresent=0;
     config=40008B18388380
   a=ptime:20

Schmidt, et al. Standards Track [Page 25] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 In this example, audio configuration data is not multiplexed into the
 RTP payload and is described only in SDP.  Furthermore, the "clock
 rate" is set to the audio sampling rate.

7.4.1.3. Example: 64 kbit/s AAC LC Stereo

 This example shows a 64 kbit/s AAC LC stereo bitstream (with an audio
 sampling rate of 24 kHz).
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/24000/2
   a=fmtp:96 profile-level-id=1; bitrate=64000; cpresent=0;
     object=2; config=400026203fc0
 In this example, audio configuration data is not multiplexed into the
 RTP payload and is described only in SDP.  Furthermore, the "clock
 rate" is set to the audio sampling rate.
 In this example, the presence of SBR cannot be determined by the SDP
 parameter set.  The "clock rate" represents the core codec sampling
 rate.  An SBR-enabled decoder can use the SBR tool to up-sample the
 audio data if the complexity and resulting output sampling rate
 permit.

7.4.1.4. Example: Use of the "SBR-enabled" Parameter

 These two examples are identical to the example above with the
 exception of the "SBR-enabled" parameter.  The presence of SBR is not
 signaled by the SDP parameters "object", "profile-level-id", and
 "config", but instead the "SBR-enabled" parameter is present.  The
 "rate" parameter and the StreamMuxConfig contain the core codec
 sampling rate.
 This example shows "SBR-enabled=0", with definitive and core codec
 sampling rates of 24 kHz.
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/24000/2
   a=fmtp:96 profile-level-id=1; bitrate=64000; cpresent=0;
     SBR-enabled=0; config=400026203fc0
 This example shows "SBR-enabled=1", with core codec sampling rate of
 24 kHz, and definitive and SBR sampling rates of 48 kHz:
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/24000/2
   a=fmtp:96 profile-level-id=1; bitrate=64000; cpresent=0;
     SBR-enabled=1; config=400026203fc0

Schmidt, et al. Standards Track [Page 26] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 In this example, the "clock rate" is still 24000, and this
 information is used for RTP timestamp calculation.  The value of
 24000 is used to support old AAC decoders.  This makes the decoder
 supporting only AAC understand the HE AAC coded data, although only
 plain AAC is supported.  A HE AAC decoder is able to generate output
 data with the SBR sampling rate.

7.4.1.5. Example: Hierarchical Signaling of SBR

 When the presence of SBR is explicitly signaled by the SDP parameters
 "object", "profile-level-id", or "config", as in the example below,
 the StreamMuxConfig contains both the core codec sampling rate and
 the SBR sampling rate.
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/48000/2
   a=fmtp:96 profile-level-id=44; bitrate=64000; cpresent=0;
     config=40005623101fe0; SBR-enabled=1
 This "config" string uses the explicit signaling mode 2.A
 (hierarchical signaling; see [14496-3].  This means that the AOT
 (Audio Object Type) is SBR (5) and SFI (Sampling Frequency Index) is
 6 (24000 Hz), which refers to the underlying core codec sampling
 frequency.  CC (Channel Configuration) is stereo (2), and the ESFI
 (Extension Sampling Frequency Index)=3 (48000) is referring to the
 sampling frequency of the extension tool (SBR).

7.4.1.6. Example: HE AAC v2 Signaling

 HE AAC v2 decoders are required to always produce a stereo signal
 from a mono signal.  Hence, there is no parameter necessary to signal
 the presence of PS.
 This example shows "SBR-enabled=1" with 1 channel signaled in the
 "a=rtpmap" line and within the "config" parameter.  The core codec
 sampling rate is 24 kHz; the definitive and SBR sampling rates are 48
 kHz.  The core codec channel configuration is mono; the PS channel
 configuration is stereo.
   m=audio 49230 RTP/AVP 110
   a=rtpmap:110 MP4A-LATM/24000/1
   a=fmtp:110 profile-level-id=15; object=2; cpresent=0;
     config=400026103fc0; SBR-enabled=1

Schmidt, et al. Standards Track [Page 27] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

7.4.1.7. Example: Hierarchical Signaling of PS

 This example shows 48 kHz stereo audio input.
   m=audio 49230 RTP/AVP 110
   a=rtpmap:110 MP4A-LATM/48000/2
   a=fmtp:110 profile-level-id=48; cpresent=0; config=4001d613101fe0
 The "config" parameter indicates explicit hierarchical signaling of
 PS and SBR.  This configuration method is not supported by legacy AAC
 an HE AAC decoders, and these are therefore unable to decode the
 coded data.

7.4.1.8. Example: MPEG Surround

 The following examples show how MPEG Surround configuration data can
 be signaled using SDP.  The configuration is carried within the
 "config" string in the first example by using two different layers.
 The general parameters in this example are: AudioMuxVersion=1;
 allStreamsSameTimeFraming=1; numSubFrames=0; numProgram=0;
 numLayer=1.  The first layer describes the HE AAC payload and signals
 the following parameters: ascLen=25; audioObjectType=2 (AAC LC);
 extensionAudioObjectType=5 (SBR); samplingFrequencyIndex=6 (24 kHz);
 extensionSamplingFrequencyIndex=3 (48 kHz); channelConfiguration=2
 (2.0 channels).  The second layer describes the MPEG Surround payload
 and specifies the following parameters: ascLen=110;
 AudioObjectType=30 (MPEG Surround); samplingFrequencyIndex=3 (48
 kHz); channelConfiguration=6 (5.1 channels); sacPayloadEmbedding=1;
 SpatialSpecificConfig=(48 kHz; 32 slots; 525 tree; ResCoding=1;
 ResBands=[7,7,7,7]).
 In this example, the signaling is carried by using two different LATM
 layers.  The MPEG Surround payload is carried together with the AAC
 payload in a single layer as indicated by the sacPayloadEmbedding
 Flag.
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/48000
   a=fmtp:96 profile-level-id=1; bitrate=64000; cpresent=0;
     SBR-enabled=1;
     config=8FF8004192B11880FF0DDE3699F2408C00536C02313CF3CE0FF0

7.4.1.9. Example: MPEG Surround with Extended SDP Parameters

 The following example is an extension of the configuration given
 above by the MPEG-Surround-specific parameters.  The "MPS-asc"
 parameter specifies the MPEG Surround Baseline Profile at Level 3
 (PLI55), and the "MPS-asc" string contains the hexadecimal

Schmidt, et al. Standards Track [Page 28] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 representation of the MPEG Surround ASC [audioObjectType=30 (MPEG
 Surround); samplingFrequencyIndex=0x3 (48 kHz);
 channelConfiguration=6 (5.1 channels); sacPayloadEmbedding=1;
 SpatialSpecificConfig=(48 kHz; 32 slots; 525 tree; ResCoding=1;
 ResBands=[0,13,13,13])].
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/48000
   a=fmtp:96 profile-level-id=44; bitrate=64000; cpresent=0;
     config=40005623101fe0; MPS-profile-level-id=55;
     MPS-asc=F1B4CF920442029B501185B6DA00;

7.4.1.10. Example: MPEG Surround with Single-Layer Configuration

 The following example shows how MPEG Surround configuration data can
 be signaled using the SDP "config" parameter.  The configuration is
 carried within the "config" string using a single layer.  The general
 parameters in this example are: AudioMuxVersion=1;
 allStreamsSameTimeFraming=1; numSubFrames=0; numProgram=0;
 numLayer=0.  The single layer describes the combination of HE AAC and
 MPEG Surround payload and signals the following parameters:
 ascLen=101; audioObjectType=2 (AAC LC); extensionAudioObjectType=5
 (SBR); samplingFrequencyIndex=7 (22.05 kHz);
 extensionSamplingFrequencyIndex=7 (44.1 kHz); channelConfiguration=2
 (2.0 channels).  A backward-compatible extension according to
 [14496-3/Amd.1] signals the presence of MPEG Surround payload data
 and specifies the following parameters: SpatialSpecificConfig=(44.1
 kHz; 32 slots; 525 tree; ResCoding=0).
 In this example, the signaling is carried by using a single LATM
 layer.  The MPEG Surround payload is carried together with the HE AAC
 payload in a single layer.
   m=audio 49230 RTP/AVP 96
   a=rtpmap:96 MP4A-LATM/44100
   a=fmtp:96 profile-level-id=44; bitrate=64000; cpresent=0;
     SBR-enabled=1; config=8FF8000652B920876A83A1F440884053620FF0;
     MPS-profile-level-id=55

8. IANA Considerations

 This document updates the media subtypes "MP4A-LATM" and "MP4V-ES"
 from RFC 3016.  The new registrations are in Sections 7.1 and 7.3 of
 this document.

Schmidt, et al. Standards Track [Page 29] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

9. Acknowledgements

 The authors would like to thank Yoshihiro Kikuchi, Yoshinori Matsui,
 Toshiyuki Nomura, Shigeru Fukunaga, and Hideaki Kimata for their work
 on RFC 3016, and Ali Begen, Keith Drage, Roni Even, and Qin Wu for
 their valuable input and comments on this document.

10. Security Considerations

 RTP packets using the payload format defined in this specification
 are subject to the security considerations discussed in the RTP
 specification [RFC3550] and in any applicable RTP profile.  The main
 security considerations for the RTP packet carrying the RTP payload
 format defined within this document are confidentiality, integrity,
 and source authenticity.  Confidentiality is achieved by encryption
 of the RTP payload, and integrity of the RTP packets is achieved
 through a suitable cryptographic integrity protection mechanism.  A
 cryptographic system may also allow the authentication of the source
 of the payload.  A suitable security mechanism for this RTP payload
 format should provide confidentiality, integrity protection, and (at
 least) source authentication capable of determining whether or not an
 RTP packet is from a member of the RTP session.
 Note that most MPEG-4 codecs define an extension mechanism to
 transmit extra data within a stream that is gracefully skipped by
 decoders that do not support this extra data.  This may be used to
 transmit unwanted data in an otherwise valid stream.
 The appropriate mechanism to provide security to RTP and payloads
 following this may vary.  It is dependent on the application, the
 transport, and the signaling protocol employed.  Therefore, a single
 mechanism is not sufficient, although, if suitable, the usage of the
 Secure Real-time Transport Protocol (SRTP) [RFC3711] is recommended.
 Other mechanisms that may be used are IPsec [RFC4301] and Transport
 Layer Security (TLS) [RFC5246] (e.g., for RTP over TCP), but other
 alternatives may also exist.
 This RTP payload format and its media decoder do not exhibit any
 significant non-uniformity in the receiver-side computational
 complexity for packet processing, and thus are unlikely to pose a
 denial-of-service threat due to the receipt of pathological data.
 The complete MPEG-4 System allows for transport of a wide range of
 content, including Java applets (MPEG-J) and scripts.  Since this
 payload format is restricted to audio and video streams, it is not
 possible to transport such active content in this format.

Schmidt, et al. Standards Track [Page 30] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

11. Differences to RFC 3016

 The RTP payload format for MPEG-4 Audio as specified in RFC 3016 is
 used by the 3GPP PSS service [3GPP].  However, there are some
 misalignments between RFC 3016 and the 3GPP PSS specification that
 are addressed by this update:
 o  The audio payload format (LATM) referenced in this document is the
    newer format specified in [14496-3], which is binary compatible to
    the format used in [3GPP].  This newer format is not binary
    compatible with the LATM referenced in RFC 3016, which is
    specified in [14496-3:1999/Amd.1:2000].
 o  The audio signaling format (StreamMuxConfig) referenced in this
    document is binary compatible to the format used in [3GPP].  The
    StreamMuxConfig element has also been revised by MPEG since RFC
    3016.
 o  The use of an audio parameter "SBR-enabled" is now defined in this
    document, which is used by 3GPP implementations [3GPP].  RFC 3016
    does not define this parameter.
 o  The "rate" parameter is defined unambiguously in this document for
    the case of presence of SBR (Spectral Band Replication).  In RFC
    3016, the definition of the "rate" parameter is ambiguous.
 o  The number of audio channels parameter is defined unambiguously in
    this document for the case of presence of PS (Parametric Stereo).
    At the time RFC 3016 was written, PS was not yet defined.
 Furthermore, some comments have been addressed and signaling support
 for MPEG Surround [23003-1] was added.
 Below is a summary of the changes in requirements by this update:
 o  In the dynamic assignment of RTP payload types for scalable MPEG-4
    Audio streams, the server SHALL assign a different value to each
    layer.
 o  The dependency relationships between the enhanced layer and the
    base layer for scalable MPEG-4 Audio streams MUST be signaled as
    specified in [RFC5583].
 o  If the size of an audioMuxElement is so large that the size of the
    RTP packet containing it does exceed the size of the Path MTU, the
    audioMuxElement SHALL be fragmented and spread across multiple
    packets.

Schmidt, et al. Standards Track [Page 31] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 o  The receiver MUST ignore any unspecified parameter in order to
    ensure that additional parameters can be added in any future
    revision of this specification.

12. References

12.1. Normative References

 [14496-2]  MPEG, "ISO/IEC International Standard 14496-2 - Coding of
            audio-visual objects, Part 2: Visual", 2003.
 [14496-3]  MPEG, "ISO/IEC International Standard 14496-3 - Coding of
            audio-visual objects, Part 3 Audio", 2009.
 [14496-3/Amd.1]
            MPEG, "ISO/IEC International Standard 14496-3 - Coding of
            audio-visual objects, Part 3: Audio, Amendment 1: HD-AAC
            profile and MPEG Surround signaling", 2009.
 [23003-1]  MPEG, "ISO/IEC International Standard 23003-1 - MPEG
            Surround (MPEG D)", 2007.
 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119, March 1997.
 [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
            Jacobson, "RTP: A Transport Protocol for Real-Time
            Applications", STD 64, RFC 3550, July 2003.
 [RFC4288]  Freed, N. and J. Klensin, "Media Type Specifications and
            Registration Procedures", BCP 13, RFC 4288, December 2005.
 [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
            Description Protocol", RFC 4566, July 2006.
 [RFC4629]  Ott, H., Bormann, C., Sullivan, G., Wenger, S., and R.
            Even, "RTP Payload Format for ITU-T Rec", RFC 4629,
            January 2007.
 [RFC4855]  Casner, S., "Media Type Registration of RTP Payload
            Formats", RFC 4855, February 2007.
 [RFC5583]  Schierl, T. and S. Wenger, "Signaling Media Decoding
            Dependency in the Session Description Protocol (SDP)",
            RFC 5583, July 2009.

Schmidt, et al. Standards Track [Page 32] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

12.2. Informative References

 [14496-1]  MPEG, "ISO/IEC International Standard 14496-1 - Coding of
            audio-visual objects, Part 1 Systems", 2004.
 [14496-12] MPEG, "ISO/IEC International Standard 14496-12 - Coding of
            audio-visual objects, Part 12 ISO base media file format".
 [14496-14] MPEG, "ISO/IEC International Standard 14496-14 - Coding of
            audio-visual objects, Part 12 MP4 file format".
 [14496-3:1999/Amd.1:2000]
            MPEG, "ISO/IEC International Standard 14496-3 - Coding of
            audio-visual objects, Part 3 Audio, Amendment 1: Audio
            extensions", 2000.
 [3GPP]     3GPP, "3rd Generation Partnership Project; Technical
            Specification Group Services and System Aspects;
            Transparent end-to-end Packet-switched Streaming Service
            (PSS); Protocols and codecs (Release 9)", 3GPP TS 26.234
            V9.5.0, December 2010.
 [H245]     International Telecommunication Union, "Control protocol
            for multimedia communication", ITU Recommendation H.245,
            December 2009.
 [H261]     International Telecommunication Union, "Video codec for
            audiovisual services at p x 64 kbit/s", ITU
            Recommendation H.261, March 1993.
 [H323]     International Telecommunication Union, "Packet-based
            multimedia communications systems", ITU
            Recommendation H.323, December 2009.
 [RFC2198]  Perkins, C., Kouvelas, I., Hodson, O., Hardman, V.,
            Handley, M., Bolot, J., Vega-Garcia, A., and S. Fosse-
            Parisis, "RTP Payload for Redundant Audio Data", RFC 2198,
            September 1997.
 [RFC3016]  Kikuchi, Y., Nomura, T., Fukunaga, S., Matsui, Y., and H.
            Kimata, "RTP Payload Format for MPEG-4 Audio/Visual
            Streams", RFC 3016, November 2000.
 [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
            A., Peterson, J., Sparks, R., Handley, M., and E.
            Schooler, "SIP: Session Initiation Protocol", RFC 3261,
            June 2002.

Schmidt, et al. Standards Track [Page 33] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

 [RFC3640]  van der Meer, J., Mackie, D., Swaminathan, V., Singer, D.,
            and P. Gentric, "RTP Payload Format for Transport of
            MPEG-4 Elementary Streams", RFC 3640, November 2003.
 [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
            Norrman, "The Secure Real-time Transport Protocol (SRTP)",
            RFC 3711, March 2004.
 [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
            Internet Protocol", RFC 4301, December 2005.
 [RFC4628]  Even, R., "RTP Payload Format for H.263 Moving RFC 2190 to
            Historic Status", RFC 4628, January 2007.
 [RFC5109]  Li, A., "RTP Payload Format for Generic Forward Error
            Correction", RFC 5109, December 2007.
 [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
            (TLS) Protocol Version 1.2", RFC 5246, August 2008.
 [RFC5691]  de Bont, F., Doehla, S., Schmidt, M., and R.
            Sperschneider, "RTP Payload Format for Elementary Streams
            with MPEG Surround Multi-Channel Audio", RFC 5691,
            October 2009.

Schmidt, et al. Standards Track [Page 34] RFC 6416 RTP Payload Format for MPEG-4 Streams October 2011

Authors' Addresses

 Malte Schmidt
 Dolby Laboratories
 Deutschherrnstr. 15-19
 90537 Nuernberg
 DE
 Phone: +49 911 928 91 42
 EMail: malte.schmidt@dolby.com
 Frans de Bont
 Philips Electronics
 High Tech Campus 36
 5656 AE Eindhoven
 NL
 Phone: +31 40 2740234
 EMail: frans.de.bont@philips.com
 Stefan Doehla
 Fraunhofer IIS
 Am Wolfmantel 33
 91058 Erlangen
 DE
 Phone: +49 9131 776 6042
 EMail: stefan.doehla@iis.fraunhofer.de
 Jaehwan Kim
 LG Electronics Inc.
 VCS/HE, 16Fl. LG Twin Towers
 Yoido-Dong, YoungDungPo-Gu,
 Seoul 150-721
 Korea
 Phone: +82 10 6225 0619
 EMail: kjh1905m@naver.com

Schmidt, et al. Standards Track [Page 35]

/data/webs/external/dokuwiki/data/pages/rfc/rfc6416.txt · Last modified: 2011/10/18 18:26 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki