rfc:rfc5195
Network Working Group H. Ould-Brahim Request for Comments: 5195 D. Fedyk Category: Standards Track Nortel
Y. Rekhter
Juniper Networks
June 2008
BGP-Based Auto-Discovery for Layer-1 VPNs
Status of This Memo
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Abstract
The purpose of this document is to define a BGP-based auto-discovery mechanism for Layer-1 VPNs (L1VPNs). The auto-discovery mechanism for L1VPNs allows the provider network devices to dynamically discover the set of Provider Edges (PEs) having ports attached to Customer Edge (CE) members of the same VPN. That information is necessary for completing the signaling phase of L1VPN connections. One main objective of a L1VPN auto-discovery mechanism is to support the "single-end provisioning" model, where addition of a new port to a given L1VPN would involve configuration changes only on the PE that has this port and on the CE that is connected to the PE via this port.
1. Introduction
The purpose of this document is to define a BGP-based auto-discovery mechanism for Layer-1 VPNs (L1VPNs) [L1VPN-FRMK]. The auto-discovery mechanism for L1VPNs allows the provider network devices to dynamically discover the set of PEs having ports attached to CE members of the same VPN. That information is necessary for completing the signaling phase of L1VPN connections. One main objective of a L1VPN auto-discovery mechanism is to support the "single-end provisioning" model, where addition of a new port to a given L1VPN would involve configuration changes only on the PE that has this port and on the CE that is connected to the PE via this port.
Ould-Brahim, et al. Standards Track [Page 1] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
The auto-discovery mechanism proceeds by having a PE advertise to other PEs the following information, at a minimum: its own IP address and the list of <private address, provider address> tuples local to that PE. Once that information is received, the remote PEs will identify the list of VPN members they have in common with the advertising PE, and use the information carried within the discovery mechanism to perform address resolution during the signaling phase of Layer-1 VPN connections.
Figure 1 highlights the network reference for using a BGP-based auto-discovery mechanism for Layer-1 VPNs. For the purpose of the auto-discovery mechanism, BGP is running only on the provider network. The PEs maintain per-VPN information tables called Port Information Tables (PITs) related to <private address, provider address> information. More information on the PITs is in Section 2.
PE1 PE2
+---------+ +--------------+
+--------+ | +------+| | +----------+ | +--------+
| VPN-A | | |VPN-A || | | VPN-A | | | VPN-A |
| CE1 |--| |PIT || BGP route | | PIT | |-| CE2 |
+--------+ | | ||<----------->| | | | +--------+
| +------+| Distribution| +----------+ |
| | | |
+--------+ | +------+| | +----------+ | +--------+
| VPN-B | | |VPN-B || -------- | | VPN-B | | | VPN-B |
| CE1 |--| |PIT ||-( GMPLS )-| | PIT | |-| CE2 |
+--------+ | | || (Backbone ) | | | | +--------+
| +------+| --------- | +----------+ |
| | | |
+--------+ | +-----+ | | +----------+ | +--------+
| VPN-C | | |VPN-C| | | | VPN-C | | | VPN-C |
| CE1 |--| |PIT | | | | PIT | |-| CE2 |
+--------+ | | | | | | | | +--------+
| +-----+ | | +----------+ |
+---------+ +--------------+
Figure 1: BGP Auto-Discovery for L1VPN
[L1VPN-FRMK] describes two modes of operation for a L1VPN: the basic mode and the enhanced mode. This document describes an auto- discovery mechanism for the basic mode only.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].
Ould-Brahim, et al. Standards Track [Page 2] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
2. Procedures
In the context of L1VPNs, a CE is connected to a PE via one or more ports, where each port may consist of one or more channels or sub- channels. Each port on a CE that connects the CE to a PE has an identifier that is unique within that L1VPN (but need not be unique across several L1VPNs). We refer to this identifier as the customer port identifier (CPI). Each port on a PE also has an identifier that is unique within the provider network. We refer to this identifier as the provider port identifier (PPI). Note that IP addresses used for CPIs or PPIs could be either IPv4 or IPv6 addresses.
For each L1VPN that has at least one port configured on a PE, the PE maintains a Port Information Table (PIT). A PIT contains a list of <CPI, PPI> tuples for all the ports within its L1VPN. Note that a PIT may also hold routing information (for example, when CPIs are learnt using a routing protocol).
A PIT on a given PE is populated with two types of information.
- Information related to the CEs' ports attached to the ports on the
PE. This information could be locally configured at the PE or
could be received from the CEs.
- Information received from other PEs through the auto-discovery
mechanism.
We refer to the former as local information, and to the latter as remote information. Propagation of local information to other PEs is accomplished by using BGP multiprotocol extensions [RFC4760]. To restrict the flow of this information to only the PITs within a given L1VPN, we use BGP route filtering based on the Route Target Extended Community [BGP-COMM], as follows.
Each PIT on a PE is configured with one or more Route Target Communities, called "export Route Targets", that are used for tagging the local information when it is exported into the provider's BGP. The granularity of such tagging could be as fine as a single <CPI, PPI> pair. In addition, each PIT on a PE is configured (at provisioning time) with one or more Route Target Communities, called "import Route Targets", that restrict the set of routes that could be imported from provider's BGP into the PIT to only the routes that have at least one of these Communities.
Each of the following occurs at provisioning time: if a service
provider adds a new L1VPN port to a particular PE, this port is
associated with a PIT on that PE, and this PIT is associated with
that L1VPN.
Ould-Brahim, et al. Standards Track [Page 3] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
Note that since the protocol used to populate a PIT with remote information is BGP, and since BGP works across multiple autonomous systems (ASs), it follows that the mechanism described in this document could support L1VPNs that span multiple autonomous systems.
Although multi-AS L1VPNs are currently out of scope for the Basic Mode, the mechanisms defined in this document appear to be easily applicable to a multi-AS scenario, should such a need arise in the future. At that time, additional work may be required to examine various aspects including security.
3. Carrying L1VPN Information in BGP
The <CPI, PPI> mapping is carried using the Multiprotocol Extensions to BGP [RFC4760]. [RFC4760] defines the format of two BGP attributes, MP_REACH_NLRI and MP_UNREACH_NLRI, that can be used to announce and withdraw the announcement of reachability information. We introduce a new subsequent address family identifier, called Layer-1 VPN auto-discovery information (value 69), and also a new Network Layer Reachability Information (NLRI) format for carrying the CPI and PPI information.
One or more <PPI, CPI> tuples could be carried in the above mentioned BGP attributes.
The format of the NLRI is described in Figure 2.
+---------------------------------------+
| Length (1 octet) |
+---------------------------------------+
| Auto-discovery info (variable) |
+---------------------------------------+
Figure 2: Encoding of the NLRI
Note that the encoding of the auto-discovery information is described in [L1VPN-BM], and note also that if the value of the Length of the Next Hop field (of the MP_REACH_NLRI attribute) is 4, then the Next Hop contains an IPv4 address. If this value is 16, then the Next Hop contains an IPv6 address.
Ould-Brahim, et al. Standards Track [Page 4] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
4. Carrying L1VPN Traffic Engineering Information in BGP
In addition to reachability information, the auto-discovery mechanism MAY carry Traffic Engineering information used for the purpose of egress path selection. For example, a PE may learn the switching capability and the maximum LSP bandwidth of remote L1VPN interfaces from the remote PEs. This document uses the BGP Traffic Engineering Attribute [BGP-TE-ATTRIBUTE] to carry such information.
5. Scalability
Recall that the Service Provider network consists of (a) PEs, (b) BGP Route Reflectors, (c) P nodes (which are neither PEs nor Route Reflectors), and, in the case of multi-provider VPNs, (d) Autonomous System Border Routers (ASBRs).
A PE router, unless it is a Route Reflector, does not retain L1VPN- related information unless it has at least one VPN with an import Route Target identical to one of the VPN-related information Route Target attributes. If a PE does not have a VPN with a matching import Route Target, it MUST then discard received l1VPN information. Inbound filtering MUST be used to cause such information to be discarded. If a new import Route Target is later added to one of the PE's VPNs (a "VPN Join" operation), it MUST then acquire the VPN- related information it previously has discarded.
In this case, the refresh mechanism described in [BGP-RFSH] MUST be used. The outbound route filtering mechanisms of [BGP-ORF] and [BGP-CONS] can also be used to advantage to make the filtering more dynamic.
Similarly, if a particular import Route Target is no longer present
in any of a PE's VPN (as a result of one or more "VPN Prune"
operations), the PE MAY discard all the L1VPN BGP routes that, as a
result, no longer have any of the PE's PIT's import Route Targets as
one of their Route Target attributes.
Note that "VPN Join" and "VPN Prune" operations are non-disruptive, and do not require any BGP connections to be brought down, as long as the refresh mechanism of [BGP-RFSH] is used.
As a result of these distribution rules, no one PE ever needs to maintain all routes for all L1VPNs; this is an important scalability consideration.
Ould-Brahim, et al. Standards Track [Page 5] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
Route reflectors can be partitioned among VPNs so that each partition carries routes for only a subset of the L1VPNs supported by the Service Provider. Thus, no single route reflector is required to maintain VPN-related information for all VPNs.
For inter-provider VPNs, if multi-hop External BGP (EBGP) is used, then the ASBRs need not maintain and distribute VPN-related information at all. P routers do not maintain any VPN-related information.
As a result, no single component within the Service Provider network has to maintain all the VPN-related information for all the VPNs. So the total capacity of the network to support increasing numbers of VPNs is not limited by the capacity of any individual component.
An important consideration to remember is that one may have any number of INDEPENDENT BGP systems carrying VPN-related information. This is unlike the case of the Internet, where the Internet BGP system MUST carry all the Internet routes. Thus, one significant (but perhaps subtle) distinction between the use of BGP for the Internet routing and the use of BGP for distributing VPN-related information, as described in this document, is that the former is not amenable to partition, while the latter is.
6. Security Considerations
This document describes a BGP-based auto-discovery mechanism that
enables a PE that attaches to a particular L1VPN to discover the set
of other PE routers that attach to the same VPN. Each PE router that
is attached to a given VPN uses BGP to advertise that fact. Other PE
routers that attach to the same VPN receive these BGP advertisements.
This allows that set of PEs to discover each other. Note that a PE
will not always receive these advertisements directly from the remote
PEs; the advertisements can be received from "intermediate" BGP
speakers.
It is of critical importance that a particular PE MUST NOT be "discovered" to be attached to a particular VPN unless that PE really is attached to that VPN, and indeed is properly authorized to be attached to that VPN. If any arbitrary node on the Internet could start sending these BGP advertisements, and if those advertisements were able to reach the PE nodes, and if the PE nodes accepted those advertisements, then anyone could add any site to any L1VPN. Thus, the auto-discovery procedures described here presuppose that a particular PE trusts its BGP peers to be who they appear to be, and further, that it can trust those peers to be properly securing their
Ould-Brahim, et al. Standards Track [Page 6] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
local attachments. (That is, a PE MUST trust that its peers are attached to, and are authorized to be attached to, the L1VPNs to which they claim to be attached.)
If a particular remote PE is a BGP peer of the local PE, then the BGP
authentication procedures of [RFC2385] SHOULD be used to ensure that
the remote PE is who it claims to be, i.e., that it is a PE that is
trusted.
If a particular remote PE is not a BGP peer of the local PE, then the information it is advertising is being distributed to the local PE through a chain of BGP speakers. The local PE MUST trust that its peers only accept information from peers that they trust in turn, and this trust relation MUST be transitive. BGP does not provide a way to determine that any particular piece of received information originated from a BGP speaker that was authorized to advertise that particular piece of information. Hence, the procedures of this document MUST be used only in environments where adequate trust relationships exist among the BGP speakers (such as the case of using the auto-discovery mechanism within a single provider network).
7. IANA Considerations
This document assigns a new SAFI, called Layer-1 VPN auto-discovery information (see Section 3). This assignment has been made in the Subsequent Address Family Identifier (SAFI) registry using the Standards Action allocation procedures. The value is 69.
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760, January
2007.
[BGP-RFSH] Chen, E., "Route Refresh Capability for BGP-4", RFC
2918, September 2000.
8.2. Informative References
[BGP-TE-ATTRIBUTE]
Ould-Brahim, H., Fedyk, D., and Rekhter, Y., "Traffic
Engineering Attribute", Work in Progress, January 2008.
Ould-Brahim, et al. Standards Track [Page 7] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
[BGP-ORF] Chen, E. and Y. Rekhter, "Outbound Route Filtering
Capability for BGP-4", Work in Progress, September 2006.
[BGP-CONS] Marques, P., Bonica, R., Fang, L., Martini, L., Raszuk,
R., Patel, K., and J. Guichard, "Constrained Route
Distribution for Border Gateway Protocol/MultiProtocol
Label Switching (BGP/MPLS) Internet Protocol (IP)
Virtual Private Networks (VPNs)", RFC 4684, November
2006.
[BGP-COMM] Sangli, S., Tappan, D., and Y. Rekhter, "BGP Extended
Communities Attribute", RFC 4360, February 2006.
[L1VPN-FRMK] Takeda, T., Ed., "Framework and Requirements for Layer 1
Virtual Private Networks", RFC 4847, April 2007.
[L1VPN-BM] Fedyk, D., Ed., Rekhter, Y., Ed., Papadimitriou, D.,
Rabbat, R., and L. Berger, "Layer 1 VPN Basic Mode",
Work in Progress, February 2008.
[RFC2385] Heffernan, A., "Protection of BGP Sessions via the TCP
MD5 Signature Option", RFC 2385, August 1998.
9. Acknowledgment
We would like to thank Adrian Farrel for the useful comments.
Ould-Brahim, et al. Standards Track [Page 8] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
Authors' Addresses
Hamid Ould-Brahim Nortel PO Box 3511 Station C Ottawa ON K1Y 4H7 Canada
Phone: +1 (613) 763 4730 EMail: hbrahim@nortel.com
Yakov Rekhter Juniper Networks 1194 N. Mathilda Avenue Sunnyvale, CA 94089 USA
EMail: yakov@juniper.net
Don Fedyk Nortel 600 Technology Park Billerica, MA 01821 USA
Phone: +1 (978) 288 3041 Email: dwfedyk@nortel.com
Ould-Brahim, et al. Standards Track [Page 9] RFC 5195 BGP Auto-Discovery for L1VPNs June 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
Ould-Brahim, et al. Standards Track [Page 10]
/data/webs/external/dokuwiki/data/pages/rfc/rfc5195.txt · Last modified: 2008/06/04 21:42 by 127.0.0.1