GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc5072

Network Working Group S. Varada, Ed. Request for Comments: 5072 Transwitch Obsoletes: 2472 D. Haskins Category: Standards Track E. Allen

                                                        September 2007
                       IP Version 6 over PPP

Status of This Memo

 This document specifies an Internet standards track protocol for the
 Internet community, and requests discussion and suggestions for
 improvements.  Please refer to the current edition of the "Internet
 Official Protocol Standards" (STD 1) for the standardization state
 and status of this protocol.  Distribution of this memo is unlimited.

Abstract

 The Point-to-Point Protocol (PPP) provides a standard method of
 encapsulating network-layer protocol information over point-to-point
 links.  PPP also defines an extensible Link Control Protocol, and
 proposes a family of Network Control Protocols (NCPs) for
 establishing and configuring different network-layer protocols.
 This document defines the method for sending IPv6 packets over PPP
 links, the NCP for establishing and configuring the IPv6 over PPP,
 and the method for forming IPv6 link-local addresses on PPP links.
 It also specifies the conditions for performing Duplicate Address
 Detection on IPv6 global unicast addresses configured for PPP links
 either through stateful or stateless address autoconfiguration.
 This document obsoletes RFC 2472.

Varada, et al. Standards Track [Page 1] RFC 5072 IP Version 6 over PPP September 2007

Table of Contents

 1. Introduction ....................................................2
    1.1. Specification of Requirements ..............................3
 2. Sending IPv6 Datagrams ..........................................3
 3. A PPP Network Control Protocol for IPv6 .........................3
 4. IPV6CP Configuration Options ....................................4
    4.1. Interface Identifier .......................................4
 5. Stateless Autoconfiguration and Link-Local Addresses ............9
 6. Security Considerations ........................................11
 7. IANA Considerations ............................................11
 8. Acknowledgments ................................................11
 9. References .....................................................12
    9.1. Normative References ......................................12
    9.2. Informative references ....................................12
 Appendix A:  Global Scope Addresses................................14
 Appendix B:  Changes from RFC-2472.................................14

1. Introduction

 PPP has three main components:
 1) A method for encapsulating datagrams over serial links.
 2) A Link Control Protocol (LCP) for establishing, configuring, and
    testing the data-link connection.
 3) A family of Network Control Protocols (NCPs) for establishing and
    configuring different network-layer protocols.
 In order to establish communications over a point-to-point link, each
 end of the PPP link must first send LCP packets to configure and test
 the data link.  After the link has been established and optional
 facilities have been negotiated as needed by the LCP, PPP must send
 NCP packets to choose and configure one or more network-layer
 protocols.  Once each of the chosen network-layer protocols has been
 configured, datagrams from each network-layer protocol can be sent
 over the link.
 In this document, the NCP for establishing and configuring the IPv6
 over PPP is referred to as the IPv6 Control Protocol (IPV6CP).
 The link will remain configured for communications until explicit LCP
 or NCP packets close the link down, or until some external event
 occurs (power failure at the other end, carrier drop, etc.).
 This document obsoletes the earlier specification from RFC 2472 [7].
 Changes from RFC 2472 are listed in Appendix B.

Varada, et al. Standards Track [Page 2] RFC 5072 IP Version 6 over PPP September 2007

1.1. Specification of Requirements

 In this document, several words are used to signify the requirements
 of the specification.
 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in [6].

2. Sending IPv6 Datagrams

 Before any IPv6 packets may be communicated, PPP MUST reach the
 network-layer protocol phase, and the IPv6 Control Protocol MUST
 reach the Opened state.
 Exactly one IPv6 packet is encapsulated in the Information field of
 PPP Data Link Layer frames where the Protocol field indicates Type
 hex 0057 (Internet Protocol Version 6).
 The maximum length of an IPv6 packet transmitted over a PPP link is
 the same as the maximum length of the Information field of a PPP data
 link layer frame.  PPP links supporting IPv6 MUST allow the
 information field to be at least as large as the minimum link MTU
 size required for IPv6 [2].

3. A PPP Network Control Protocol for IPv6

 The IPv6 Control Protocol (IPV6CP) is responsible for configuring,
 enabling, and disabling the IPv6 protocol modules on both ends of the
 point-to-point link.  IPV6CP uses the same packet exchange mechanism
 as the LCP.  IPV6CP packets may not be exchanged until PPP has
 reached the network-layer protocol phase.  IPV6CP packets that are
 received before this phase is reached should be silently discarded.
 The IPv6 Control Protocol is exactly the same as the LCP [1] with the
 following exceptions:
    Data Link Layer Protocol Field
       Exactly one IPV6CP packet is encapsulated in the Information
       field of PPP Data Link Layer frames where the Protocol field
       indicates type hex 8057 (IPv6 Control Protocol).

Varada, et al. Standards Track [Page 3] RFC 5072 IP Version 6 over PPP September 2007

    Code field
       Only Codes 1 through 7 (Configure-Request, Configure-Ack,
       Configure-Nak, Configure-Reject, Terminate-Request, Terminate-
       Ack and Code-Reject) are used.  Other Codes should be treated
       as unrecognized and should result in Code-Rejects.
    Timeouts
       IPV6CP packets may not be exchanged until PPP has reached the
       network-layer protocol phase.  An implementation should be
       prepared to wait for Authentication and Link Quality
       Determination to finish before timing out waiting for a
       Configure-Ack or other response.  It is suggested that an
       implementation give up only after user intervention or a
       configurable amount of time.
    Configuration Option Types
       IPV6CP has a distinct set of Configuration Options.

4. IPV6CP Configuration Options

 IPV6CP Configuration Options allow negotiation of desirable IPv6
 parameters.  IPV6CP uses the same Configuration Option format defined
 for LCP [1] but with a separate set of Options.  If a Configuration
 Option is not included in a Configure-Request packet, the default
 value for that Configuration Option is assumed.
 Up-to-date values of the IPV6CP Option Type field are specified in
 the online database of "Assigned Numbers" maintained at IANA [9].
 The current value assignment is as follows:
    1 Interface-Identifier
 The only IPV6CP option defined in this document is the interface
 identifier.  Any other IPV6CP configuration options that can be
 defined over time are to be defined in separate documents.

4.1. Interface Identifier

 Description
 This Configuration Option provides a way to negotiate a unique, 64-
 bit interface identifier to be used for the address autoconfiguration
 [3] at the local end of the link (see Section 5).  A Configure-
 Request MUST contain exactly one instance of the interface-identifier
 option [1].  The interface identifier MUST be unique within the PPP

Varada, et al. Standards Track [Page 4] RFC 5072 IP Version 6 over PPP September 2007

 link; i.e., upon completion of the negotiation, different interface-
 identifier values are to be selected for the ends of the PPP link.
 The interface identifier may also be unique over a broader scope.
 Before this Configuration Option is requested, an implementation
 chooses its tentative interface identifier.  The non-zero value of
 the tentative interface identifier SHOULD be chosen such that the
 value is unique to the link and, preferably, consistently
 reproducible across initializations of the IPV6CP finite state
 machine (administrative Close and reOpen, reboots, etc.).  The
 rationale for preferring a consistently reproducible unique interface
 identifier to a completely random interface identifier is to provide
 stability to global scope addresses (see Appendix A) that can be
 formed from the interface identifier.
 Assuming that interface identifier bits are numbered from 0 to 63 in
 canonical bit order, where the most significant bit is the bit number
 0, the bit number 6 is the "u" bit (universal/local bit in  IEEE
 EUI-64 [4] terminology), which indicates whether or not the interface
 identifier is based on a globally unique IEEE identifier (EUI-48 or
 EUI-64 [4])(see case 1 below).  It is set to one (1) if a globally
 unique IEEE identifier is used to derive the interface identifier,
 and it is set to zero (0) otherwise.
 The following are methods for choosing the tentative interface
 identifier in the preference order:
 1) If an IEEE global identifier (EUI-48 or EUI-64) is available
    anywhere on the node, it should be used to construct the tentative
    interface identifier due to its uniqueness properties.  When
    extracting an IEEE global identifier from another device on the
    node, care should be taken that the extracted identifier is
    presented in canonical ordering [14].
    The only transformation from an EUI-64 identifier is to invert the
    "u" bit (universal/local bit in IEEE EUI-64 terminology).
    For example, for a globally unique EUI-64 identifier of the form:
 most-significant                                    least-significant
 bit                                                               bit
 |0              1|1              3|3              4|4              6|
 |0              5|6              1|2              7|8              3|
 +----------------+----------------+----------------+----------------+
 |cccccc0gcccccccc|cccccccceeeeeeee|eeeeeeeeeeeeeeee|eeeeeeeeeeeeeeee|
 +----------------+----------------+----------------+----------------+

Varada, et al. Standards Track [Page 5] RFC 5072 IP Version 6 over PPP September 2007

    where "c" are the bits of the assigned company_id, "0" is the
    value of the universal/local bit to indicate global scope, "g" is
    the group/individual bit, and "e" are the bits of the extension
    identifier, the IPv6 interface identifier would be of the form:
 most-significant                                    least-significant
 bit                                                               bit
 |0              1|1              3|3              4|4              6|
 |0              5|6              1|2              7|8              3|
 +----------------+----------------+----------------+----------------+
 |cccccc1gcccccccc|cccccccceeeeeeee|eeeeeeeeeeeeeeee|eeeeeeeeeeeeeeee|
 +----------------+----------------+----------------+----------------+
    The only change is inverting the value of the universal/local bit.
    In the case of a EUI-48 identifier, it is first converted to the
    EUI-64 format by inserting two bytes, with hexa-decimal values of
    0xFF and 0xFE, in the middle of the 48-bit MAC (between the
    company_id and extension identifier portions of the EUI-48 value).
    For example, for a globally unique 48-bit EUI-48 identifier of the
    form:
    most-significant                   least-significant
    bit                                              bit
    |0              1|1              3|3              4|
    |0              5|6              1|2              7|
    +----------------+----------------+----------------+
    |cccccc0gcccccccc|cccccccceeeeeeee|eeeeeeeeeeeeeeee|
    +----------------+----------------+----------------+
    where "c" are the bits of the assigned company_id, "0" is the
    value of the universal/local bit to indicate global scope, "g" is
    the group/individual bit, and "e" are the bits of the extension
    identifier, the IPv6 interface identifier would be of the form:
 most-significant                                    least-significant
 bit                                                               bit
 |0              1|1              3|3              4|4              6|
 |0              5|6              1|2              7|8              3|
 +----------------+----------------+----------------+----------------+
 |cccccc1gcccccccc|cccccccc11111111|11111110eeeeeeee|eeeeeeeeeeeeeeee|
 +----------------+----------------+----------------+----------------+
 2) If an IEEE global identifier is not available, a different source
    of uniqueness should be used.  Suggested sources of uniqueness
    include link-layer addresses, machine serial numbers, et cetera.

Varada, et al. Standards Track [Page 6] RFC 5072 IP Version 6 over PPP September 2007

    In this case, the "u" bit of the interface identifier MUST be set
    to zero (0).
 3) If a good source of uniqueness cannot be found, it is recommended
    that a random number be generated.  In this case, the "u" bit of
    the interface identifier MUST be set to zero (0).
 Good sources [1] of uniqueness or randomness are required for the
 interface identifier negotiation to succeed.  If neither a unique
 number nor a random number can be generated, it is recommended that a
 zero value be used for the interface identifier transmitted in the
 Configure-Request.  In this case, the PPP peer may provide a valid
 non-zero interface identifier in its response as described below.
 Note that if at least one of the PPP peers is able to generate
 separate non-zero numbers for itself and its peer, the identifier
 negotiation will succeed.
 When a Configure-Request is received with the Interface-Identifier
 Configuration Option and the receiving peer implements this option,
 the received interface identifier is compared with the interface
 identifier of the last Configure-Request sent to the peer.  Depending
 on the result of the comparison, an implementation MUST respond in
 one of the following ways:
 If the two interface identifiers are different but the received
 interface identifier is zero, a Configure-Nak is sent with a non-zero
 interface-identifier value suggested for use by the remote peer.
 Such a suggested interface identifier MUST be different from the
 interface identifier of the last Configure-Request sent to the peer.
 It is recommended that the value suggested be consistently
 reproducible across initializations of the IPV6CP finite state
 machine (administrative Close and reOpen, reboots, etc).  The "u"
 (universal/local) bit of the suggested identifier MUST be set to zero
 (0) regardless of its source unless the globally unique EUI-48/EUI-64
 derived identifier is provided for the exclusive use by the remote
 peer.
 If the two interface identifiers are different and the received
 interface identifier is not zero, the interface identifier MUST be
 acknowledged, i.e., a Configure-Ack is sent with the requested
 interface identifier, meaning that the responding peer agrees with
 the interface identifier requested.
 If the two interface identifiers are equal and are not zero,
 Configure-Nak MUST be sent specifying a different non-zero
 interface-identifier value suggested for use by the remote peer.  It
 is recommended that the value suggested be consistently reproducible
 across initializations of the IPV6CP finite state machine

Varada, et al. Standards Track [Page 7] RFC 5072 IP Version 6 over PPP September 2007

 (administrative Close and reOpen, reboots, etc).  The "u"
 (universal/local) bit of the suggested identifier MUST be set to zero
 (0) regardless of its source unless the globally unique EUI-48/EUI-64
 derived identifier is provided for the exclusive use by the remote
 peer.
 If the two interface identifiers are equal to zero, the interface
 identifier's negotiation MUST be terminated by transmitting the
 Configure-Reject with the interface-identifier value set to zero.  In
 this case, a unique interface identifier cannot be negotiated.
 If a Configure-Request is received with the Interface-Identifier
 Configuration Option and the receiving peer does not implement this
 option, Configure-Reject is sent.
 A new Configure-Request SHOULD NOT be sent to the peer until normal
 processing would cause it to be sent (that is, until a Configure-Nak
 is received or the Restart timer runs out [1]).
 A new Configure-Request MUST NOT contain the interface-identifier
 option if a valid Interface-Identifier Configure-Reject is received.
 Reception of a Configure-Nak with a suggested interface identifier
 different from that of the last Configure-Nak sent to the peer
 indicates a unique interface identifier.  In this case, a new
 Configure-Request MUST be sent with the identifier value suggested in
 the last Configure-Nak from the peer.  But if the received interface
 identifier is equal to the one sent in the last Configure-Nak, a new
 interface identifier MUST be chosen.  In this case, a new Configure-
 Request SHOULD be sent with the new tentative interface identifier.
 This sequence (transmit Configure-Request, receive Configure-Request,
 transmit Configure-Nak, receive Configure-Nak) might occur a few
 times, but it is extremely unlikely to occur repeatedly.  More
 likely, the interface identifiers chosen at either end will quickly
 diverge, terminating the sequence.
 If negotiation of the interface identifier is required, and the peer
 did not provide the option in its Configure-Request, the option
 SHOULD be appended to a Configure-Nak.  The tentative value of the
 interface identifier given must be acceptable as the remote interface
 identifier; i.e., it should be different from the identifier value
 selected for the local end of the PPP link.  The next Configure-
 Request from the peer may include this option.  If the next
 Configure-Request does not include this option, the peer MUST NOT
 send another Configure-Nak with this option included.  It should
 assume that the peer's implementation does not support this option.

Varada, et al. Standards Track [Page 8] RFC 5072 IP Version 6 over PPP September 2007

 By default, an implementation SHOULD attempt to negotiate the
 interface identifier for its end of the PPP connection.
 A summary of the Interface-Identifier Configuration Option format is
 shown below.  The fields are transmitted from left to right.
 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |     Type      |    Length     | Interface-Identifier (MS Bytes)
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                      Interface-Identifier (cont)
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Interface-Identifier (LS Bytes) |
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    Type
       1
    Length
       10
    Interface-Identifier
       The 64-bit interface identifier, which is very likely to be
       unique on the link, or zero if a good source of uniqueness
       cannot be found.
    Default
       If no valid interface identifier can be successfully
       negotiated, no default interface-identifier value should be
       assumed.  The procedures for recovering from such a case are
       unspecified.  One approach is to manually configure the
       interface identifier of the interface.

5. Stateless Autoconfiguration and Link-Local Addresses

 The interface identifier of IPv6 unicast addresses [5] of a PPP
 interface SHOULD be negotiated in the IPV6CP phase of the PPP
 connection setup (see Section 4.1).  If no valid interface identifier
 has been successfully negotiated, procedures for recovering from such
 a case are unspecified.  One approach is to manually configure the
 interface identifier of the interface.

Varada, et al. Standards Track [Page 9] RFC 5072 IP Version 6 over PPP September 2007

 The negotiated interface identifier is used by the local end of the
 PPP link to autoconfigure an IPv6 link-local unicast address for the
 PPP interface.  However, it SHOULD NOT be assumed that the same
 interface identifier is used in configuring global unicast addresses
 for the PPP interface using IPv6 stateless address autoconfiguration
 [3].  The PPP peer MAY generate one or more interface identifiers,
 for instance, using a method described in [8], to autoconfigure one
 or more global unicast addresses.
 As long as the interface identifier is negotiated in the IPV6CP phase
 of the PPP connection setup, it is redundant to perform duplicate
 address detection (DAD) as a part of the IPv6 Stateless Address
 Autoconfiguration protocol [3] on the IPv6 link-local address
 generated by the PPP peer.  It may also be redundant to perform DAD
 on any global unicast addresses configured (using an interface
 identifier that is either negotiated during IPV6CP or generated, for
 instance, as per [8]) for the interface as part of the IPv6 Stateless
 Address Autoconfiguration protocol [3] provided that the following
 two conditions are met:
    1) The prefixes advertised through the Router Advertisement
       messages by the access router terminating the PPP link are
       exclusive to the PPP link.
    2) The access router terminating the PPP link does not
       autoconfigure any IPv6 global unicast addresses from the
       prefixes that it advertises.
 Therefore, it is RECOMMENDED that for PPP links with the IPV6CP
 interface-identifier option enabled and satisfying the aforementioned
 two conditions, the default value of the DupAddrDetectTransmits
 autoconfiguration variable [3] is set to zero by the system
 management.  3GPP2 networks are an example of a technology that uses
 PPP to enable a host to obtain an IPv6 global unicast address and
 satisfies the aforementioned two conditions [10].  3GPP networks are
 another example ([11] [13]).
 Link-local addresses
 Link-local addresses of PPP interfaces have the following format:
 | 10 bits  |        54 bits         |          64 bits            |
 +----------+------------------------+-----------------------------+
 |1111111010|           0            |    Interface-Identifier     |
 +----------+------------------------+-----------------------------+

Varada, et al. Standards Track [Page 10] RFC 5072 IP Version 6 over PPP September 2007

 The most significant 10 bits of the address is the Link-Local prefix
 FE80::.  54 zero bits pad out the address between the Link-Local
 prefix and the interface-identifier fields.

6. Security Considerations

 Lack of link security, such as authentication, trigger the security
 concerns raised in [3] when the stateless address autoconfiguration
 method is employed for the generation of global unicast IPv6
 addresses out of interface identifiers that are either negotiated
 through the IPV6CP or generated, for instance, using a method
 described in [8].  Thus, the mechanisms that are appropriate for
 ensuring PPP link security are addressed below, together with the
 reference to a generic threat model.
 The mechanisms that are appropriate for ensuring PPP link Security
 are: 1) Access Control Lists that apply filters on traffic received
 over the link for enforcing admission policy, 2) an Authentication
 protocol that facilitates negotiations between peers [15] to select
 an authentication method (e.g., MD5 [16]) for validation of the peer,
 and 3) an Encryption protocol that facilitates negotiations between
 peers to select encryption algorithms (or crypto-suites) to ensure
 data confidentiality [17].
 There are certain threats associated with peer interactions on a PPP
 link even with one or more of the above security measures in place.
 For instance, using the MD5 authentication method [16] exposes one to
 replay attack, where an attacker could intercept and replay a
 station's identity and password hash to get access to a network.  The
 user of this specification is advised to refer to [15], which
 presents a generic threat model, for an understanding of the threats
 posed to the security of a link.  The reference [15] also gives a
 framework to specify requirements for the selection of an
 authentication method for a given application.

7. IANA Considerations

 The IANA has assigned value 1 for the Type field of the IPv6 datagram
 interface-identifier option specified in this document.  The current
 assignment is up-to-date at [9].

8. Acknowledgments

 This document borrows from the Magic-Number LCP option and as such is
 partially based on previous work done by the PPP working group.
 The editor is grateful for the input provided by members of the IPv6
 community in the spirit of updating RFC 2472.  Thanks, in particular,

Varada, et al. Standards Track [Page 11] RFC 5072 IP Version 6 over PPP September 2007

 go to Pete Barany and Karim El Malki for their technical
 contributions.  Also, thanks to Alex Conta for a thorough review,
 Stephen Kent for helping with security aspects, and Spencer Dawkins
 and Pekka Savola for the nits.  Finally, the author is grateful to
 Jari Arkko for his initiation to bring closure to this specification.

9. References

9.1. Normative References

 [1]   Simpson, W., Ed., "The Point-to-Point Protocol (PPP)", STD 51,
       RFC 1661, July 1994.
 [2]   Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
       Specification", RFC 2460, December 1998.
 [3]   Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address
       Autoconfiguration", RFC 4862, September 2007.
 [4]   IEEE, "Guidelines For 64-bit Global Identifier (EUI-64)",
       http://standards.ieee.org/regauth/oui/tutorials/EUI64.html
 [5]   Hinden, R. and S. Deering, "IP Version 6 Addressing
       Architecture", RFC 4291, February 2006.
 [6]   Bradner, S., "Key words for use in RFCs to Indicate Requirement
       Levels", BCP 14, RFC 2119, March 1997.
 [7]   Haskin, D. and E. Allen, "IP Version 6 over PPP", RFC 2472,
       December 1998.
 [8]   Narten T., Draves, R., and S. Krishnan, "Privacy Extensions for
       Stateless Address Autoconfiguration in IPv6", RFC 4941,
       September 2007.

9.2. Informative references

 [9]   IANA, "Assigned Numbers," http://www.iana.org/numbers.html
 [10]  3GPP2 X.S0011-002-C v1.0, "cdma2000 Wireless IP Network
       Standard: Simple IP and Mobile IP Access Services," September
       2003.
 [11]  3GPP TS 29.061 V6.4.0, "Interworking between the Public Land
       Mobile Network (PLMN) Supporting packet based services and
       Packet Data Networks (PDN) (Release 6)," April 2005.

Varada, et al. Standards Track [Page 12] RFC 5072 IP Version 6 over PPP September 2007

 [12]  Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins, C.,
       and M. Carney, "Dynamic Host Configuration Protocol for IPv6
       (DHCPv6)", RFC 3315, July 2003.
 [13]  3GPP TS 23.060 v6.8.0, "General Packet Radio Service (GPRS);
       Service description; Stage 2 (Release 6)," March 2005.
 [14]  Narten, T. and C. Burton, "A Caution On The Canonical Ordering
       Of Link-Layer Addresses", RFC 2469, December 1998.
 [15]  Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
       Levkowetz, Ed., "Extensible Authentication Protocol (EAP)", RFC
       3748, June 2004.
 [16]  Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321, April
       1992.
 [17]  Meyer, G., "The PPP Encryption Control Protocol (ECP)", RFC
       1968, June 1996.

Varada, et al. Standards Track [Page 13] RFC 5072 IP Version 6 over PPP September 2007

Appendix A: Global Scope Addresses

 A node on the PPP link creates global unicast addresses either
 through stateless or stateful address autoconfiguration mechanisms.
 In the stateless address autoconfiguration [3], the node relies on
 sub-net prefixes advertised by the router via the Router
 Advertisement messages to obtain global unicast addresses from an
 interface identifier.  In the stateful address autoconfiguration, the
 host relies on a Stateful Server, like DHCPv6 [12], to obtain global
 unicast addresses.

Appendix B: Changes from RFC 2472

 The following changes were made from RFC 2472 "IPv6 over PPP":
  1. Minor updates to Sections 3 and 4
  1. Updated the text in Section 4.1 to include the reference to

Appendix A and minor text clarifications.

  1. Removed Section 4.2 on IPv6-Compression-Protocol based on IESG

recommendation, and created a new standards-track document to

    cover negotiation of the IPv6 datagram compression protocol using
    IPV6CP.
  1. Updated the text in Section 5 to: (a) allow the use of one or more

interface identifiers generated by a peer, in addition to the use

    of interface identifier negotiated between peers of the link, in
    the creation of global unicast addresses for the local PPP
    interface, and (b) identify cases against the DAD of created non-
    link-local addresses.
  1. Added new and updated references.
  1. Added Appendix A

Varada, et al. Standards Track [Page 14] RFC 5072 IP Version 6 over PPP September 2007

Authors' Addresses

 Dimitry Haskin
 Ed Allen
 Srihari Varada (Editor)
 TranSwitch Corporation
 3 Enterprise Dr.
 Shelton, CT 06484. US.
 Phone: +1 203 929 8810
 EMail: varada@ieee.org

Varada, et al. Standards Track [Page 15] RFC 5072 IP Version 6 over PPP September 2007

Full Copyright Statement

 Copyright (C) The IETF Trust (2007).
 This document is subject to the rights, licenses and restrictions
 contained in BCP 78, and except as set forth therein, the authors
 retain all their rights.
 This document and the information contained herein are provided on an
 "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
 OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
 THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
 OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
 THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
 WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

 The IETF takes no position regarding the validity or scope of any
 Intellectual Property Rights or other rights that might be claimed to
 pertain to the implementation or use of the technology described in
 this document or the extent to which any license under such rights
 might or might not be available; nor does it represent that it has
 made any independent effort to identify any such rights.  Information
 on the procedures with respect to rights in RFC documents can be
 found in BCP 78 and BCP 79.
 Copies of IPR disclosures made to the IETF Secretariat and any
 assurances of licenses to be made available, or the result of an
 attempt made to obtain a general license or permission for the use of
 such proprietary rights by implementers or users of this
 specification can be obtained from the IETF on-line IPR repository at
 http://www.ietf.org/ipr.
 The IETF invites any interested party to bring to its attention any
 copyrights, patents or patent applications, or other proprietary
 rights that may cover technology that may be required to implement
 this standard.  Please address the information to the IETF at
 ietf-ipr@ietf.org.

Varada, et al. Standards Track [Page 16]

/data/webs/external/dokuwiki/data/pages/rfc/rfc5072.txt · Last modified: 2007/09/21 18:55 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki