rfc:rfc4561
Network Working Group J.-P. Vasseur, Ed. Request for Comments: 4561 Z. Ali Category: Standards Track S. Sivabalan
Cisco Systems, Inc.
June 2006
Definition of a Record Route Object (RRO) Node-Id Sub-Object
Status of This Memo
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
In the context of MPLS TE Fast Reroute, the Merge Point (MP) address is required at the Point of Local Repair (PLR) in order to select a backup tunnel intersecting a fast reroutable Traffic Engineering Label Switched Path (TE LSP) on a downstream Label Switching Router (LSR). However, existing protocol mechanisms are not sufficient to find an MP address in multi-domain routing networks where a domain is defined as an Interior Gateway Protocol (IGP) area or an Autonomous System (AS). Hence, the current MPLS Fast Reroute mechanism cannot be used in order to protect inter-domain TE LSPs from a failure of an Area Border Router (ABR) or Autonomous System Border Router (ASBR). This document specifies the use of existing Record Route Object (RRO) IPv4 and IPv6 sub-objects (with a new flag defined) thus defining the node-id sub-object in order to solve this issue. The MPLS Fast Reroute mechanism mentioned in this document refers to the "Facility backup" MPLS TE Fast Reroute method.
Vasseur, et al. Standards Track [Page 1] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
Table of Contents
1. Introduction ....................................................2
2. Terminology .....................................................4
2.1. Conventions Used in This Document ..........................5
3. Signaling Node-Ids in RROs ......................................5
4. Finding Merge Point .............................................6
5. Security Considerations .........................................7
6. Acknowledgements ................................................7
7. References ......................................................7
7.1. Normative References .......................................7
7.2. Informative References .....................................8
1. Introduction
MPLS Fast Reroute (FRR) [FAST-REROUTE] is a fast recovery local protection technique used to protect Traffic Engineering LSPs from link/node/Shared Risk Link Group (SRLG) failure. One or more backup tunnels are pre-established to protect against the failure of a link/node/SRLG. In case of failure, every protected TE LSP traversing the failed resource is rerouted onto the appropriate backup tunnel.
There are several requirements on the backup tunnel path that must be satisfied. First, the backup tunnel must not traverse the element that it protects. In addition, a primary tunnel and its associated backup tunnel should intersect at least at two points (nodes): Point of Local Repair (PLR) and Merge Point (MP). The former is the head- end LSR of the backup tunnel, and the latter is the tail-end LSR of the backup tunnel. The PLR is where FRR is triggered when link/node/SRLG failure happens.
There are different methods for computing paths for backup tunnels at a given PLR. Specifically, a user can statically configure one or more backup tunnels at the PLR with an explicitly configured path, or the PLR can be configured to automatically compute a backup path or to send a path computation request to a PCE (see [PCE-ARCH]).
Consider the following scenario (Figure 1).
Assumptions:
- A multi-area network made of three areas: 0, 1, and 2.
- A fast reroutable TE LSP T1 (TE LSP signaled with the "Local
Protection Desired" bit set in the SESSION-ATTRIBUTE object or the
FAST-REROUTE object) from R0 to R3.
Vasseur, et al. Standards Track [Page 2] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
- A backup tunnel B1 from R1 to R2, not traversing ABR1, and
following the R1-ABR3-R2 path.
- The PLR R1 reroutes any protected TE LSP traversing ABR1 onto the
backup tunnel B1 in case of ABR1's failure.
<--- area 1 --><---area 0---><---area 2--->
R0-----R1-ABR1--R2------ABR2--------R3
\ /
\ /
ABR3
Figure 1: Use of Fast Reroute to protect a TE LSP against an ABR
failure with MPLS Traffic Engineering Fast Reroute
When T1 is first signaled, the PLR R1 needs to dynamically select an appropriate backup tunnel intersecting T1 on a downstream LSR. However, existing protocol mechanisms are not sufficient to unambiguously find the MP address in a network with inter-domain TE LSP. This document addresses these limitations.
R1 needs to select an existing backup tunnel with the following properties:
1. The backup tunnel intersects with the primary tunnel at the MP.
For the sake of illustration, in Figure 1, R1 needs to
determine that T1 and B1 intersect at the node R2.
2. The backup tunnel satisfies the primary LSP's request with
respect to the bandwidth protection request (i.e., bandwidth
guaranteed for the primary tunnel during failure), and the type
of protection (link or node failure), as specified in
[FAST-REROUTE].
One technique for the PLR to ensure that condition (1) is met consists of examining the Record Route Object (RRO) of the primary tunnel to see whether any of the addresses specified in the RRO correspond to the MP. That said, as per [RSVP-TE], the addresses specified in the RRO IPv4 or IPv6 sub-objects sent in Resv messages can be node-ids and/or interface addresses. Hence, in Figure 1, router R2 may specify interface addresses in the RROs for T1 and B1. Note that these interface addresses are different in this example.
The problem of finding the MP using the interface addresses or node- ids can be easily solved in the case of a single IGP area. Specifically, in the case of a single IGP area, the PLR has the knowledge of all the interfaces attached to the tail-end of the backup tunnel. This information is available in PLR's IGP topology
Vasseur, et al. Standards Track [Page 3] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
database. Thus, the PLR can unambiguously determine whether a backup
tunnel intersecting a protected TE LSP on a downstream node exists
and can also find the MP address regardless of how the addresses
carried in the RRO IPv4 or IPv6 sub-objects are specified (i.e.,
whether using the interface addresses or the node-ids). However,
such routing information is not available in the case of inter-domain
environments. Hence, unambiguously making sure that condition (1)
above is met in the case of inter-domain TE LSPs is not possible with
existing mechanisms.
In this document, we define extensions to and describe the use of Resource Reservation Protocol (RSVP) [RSVP, RSVP-TE] to solve the above-mentioned problem. Note that the requirement for the support of the fast recovery technique specified in [FAST-REROUTE] to inter- domain TE LSPs has been specified in [INTER-AREA-TE-REQS] and [INTER-AS-TE-REQS].
2. Terminology
Area Border Routers (ABRs): Border routers used to connect two Interior Gateway Protocol (IGP) areas (areas in OSPF or levels in IS-IS).
Autonomous System Border Router (ASBRs): Border routers used to connect to another AS of a different or the same Service Provider via one or more links inter-connecting between ASes.
Backup Tunnel: The LSP that is used to back up one of the many LSPs in many-to-one backup.
Inter-AS TE LSP: A TE LSP that crosses an AS boundary.
Inter-area TE LSP: A TE LSP that crosses an IGP area.
LSR: Label Switching Router.
LSP: Label Switched Path.
Local Repair: Techniques used to repair TE LSPs quickly when a link, an SRLG, or a node along the TE LSP fails.
PCE: Path Computation Element. An entity (component, application, or network node) that is capable of computing a network path or route based on a network graph and applying computational constraints.
MP: Merge Point. The LSR where one or more backup tunnels rejoin the path of the protected LSP downstream of the potential failure.
Vasseur, et al. Standards Track [Page 4] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
Protected LSP: An LSP is said to be protected at a given hop if it has one or multiple associated backup tunnels originating at that hop.
PLR: Point of Local Repair. The head-end of a backup tunnel.
Reroutable LSP: Any LSP for which the "Local Protection Desired" bit is set in the Flag field of the SESSION_ATTRIBUTE object of its Path messages.
TE LSP: Traffic Engineering Label Switched Path.
2.1. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].
3. Signaling Node-Ids in RROs
As mentioned above, the limitation that we need to address is the generality of the contents of the RRO IPv4 and IPv6 sub-objects, as defined in [RSVP-TE]. [RSVP-TE] defines the IPv4 and IPv6 RRO sub- objects. Moreover, two additional flags are defined in [FAST-REROUTE]: the "Local Protection Available" and "Local Protection in Use" bits.
In this document, we define the following new flag:
Node-id: 0x20
When set, this indicates that the address specified in the RRO's
IPv4 or IPv6 sub-object is a node-id address, which refers to the
"Router Address" as defined in [OSPF-TE], or "Traffic Engineering
Router ID" as defined in [ISIS-TE]. A node MUST use the same
address consistently. Once an address is used in the RRO's IPv4
or IPv6 sub-object, it SHOULD always be used for the lifetime of
the TE LSP.
An IPv4 or IPv6 RRO sub-object with the node-id flag set is also called a node-id sub-object. The problem of finding an MP address in a network with inter-domain TE LSP is solved by inserting a node-id sub-object (an RRO "IPv4" and "IPv6" sub-object with the 0x20 flag set) in the RRO object carried in the RSVP Resv message.
Vasseur, et al. Standards Track [Page 5] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
An implementation may decide to either:
1) Add the node-id sub-object in the RRO carried in an RSVP Resv
message and, when required, also add another IPv4/IPv6 sub-object
to record interface address.
Example: an inter-domain fast reroutable TE LSP would have the
following two sub-objects in the RRO carried in Resv message: a
node-id sub-object and a label sub-object. If recording the
interface address is required, then an additional IPv4/IPv6 sub-
object is added.
or
2) Add an IPv4/IPv6 sub-object recording the interface address and,
when required, add a node-id sub-object in the RRO.
Example: an inter-domain fast reroutable TE LSP would have the
following three sub-objects in the RRO carried in Resv message: an
IPv4/IPv6 sub-object recording interface address, a label sub-
object, and a node-id sub-object.
Note also that the node-id sub-object may have other applications than Fast Reroute backup tunnel selection. Moreover, it is RECOMMENDED that an LSR recording a node-id address in an IPv4/IPv6 RRO sub-object also set the node-id flag.
4. Finding Merge Point
Two cases should be considered:
- Case 1: If the backup tunnel destination is the MP's node-id, then
a PLR can find the MP and suitable backup tunnel by simply
comparing the backup tunnel's destination address with the node-id included in the RRO of the primary tunnel.
- Case 2: If the backup tunnel terminates at an address different
from the MP's node-id, then a node-id sub-object MUST also be
included in the RRO of the backup tunnel. A PLR can find the MP and suitable backup tunnel by simply comparing the node-ids present in the RROs of both the primary and backup tunnels.
It must be noted that although the technique described in this document for selecting an appropriate backup tunnel using the node-id sub-object applies to the case of Inter-area and Inter-AS, in the case of Inter-AS, the assumption is made that the MP's node-id (of the downstream domain) does not overlap with any LSR's node-id present in the PLR's AS.
Vasseur, et al. Standards Track [Page 6] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
When both IPv4 node-id and IPv6 node-id sub-objects are present, a PLR may use any or both of them in finding the MP address.
5. Security Considerations
This document does not introduce new security issues. The security considerations pertaining to [RSVP] and [RSVP-TE] remain relevant.
6. Acknowledgements
We would like to acknowledge input and helpful comments from Carol Iturralde, Anca Zamfir, Reshad Rahman, Rob Goguen, and Philip Matthews. A special thanks to Adrian Farrel for his thorough review of this document.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to
Indicate Requirement Levels", BCP 14, RFC 2119,
March 1997.
[RSVP] Braden, R., Zhang, L., Berson, S., Herzog, S.,
and S. Jamin, "Resource ReSerVation Protocol
(RSVP) -- Version 1 Functional Specification",
RFC 2205, September 1997.
[RSVP-TE] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[FAST-REROUTE] Pan, P., Swallow, G., and A. Atlas, "Fast
Reroute Extensions to RSVP-TE for LSP Tunnels",
RFC 4090, May 2005.
[OSPF-TE] Katz, D., Kompella, K., and D. Yeung, "Traffic
Engineering (TE) Extensions to OSPF Version 2",
RFC 3630, September 2003.
[ISIS-TE] Smit, H. and T. Li, "Intermediate System to
Intermediate System (IS-IS) Extensions for
Traffic Engineering (TE)", RFC 3784, June 2004.
Vasseur, et al. Standards Track [Page 7] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
7.2. Informative References
[INTER-AREA-TE-REQS] Le Roux, J.-L., Vasseur, J.-P., and J. Boyle,
"Requirements for Inter-Area MPLS Traffic
Engineering", RFC 4105, June 2005.
[INTER-AS-TE-REQS] Zhang, R. and J.-P. Vasseur, "MPLS Inter-
Autonomous System (AS) Traffic Engineering (TE)
Requirements", RFC 4216, November 2005.
[PCE-ARCH] Farrel, A., Vasseur, J.-P., and J. Ash, "A Path
Computation Element (PCE) Based Architecture",
Work in Progress, April 2006.
Vasseur, et al. Standards Track [Page 8] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
Authors' Addresses
J.-P. Vasseur (Editor) Cisco Systems, Inc. 1414 Massachusetts Avenue Boxborough , MA - 01719 USA
EMail: jpv@cisco.com
Zafar Ali Cisco Systems, Inc. 100 South Main St. #200 Ann Arbor, MI 48104 USA
EMail: zali@cisco.com
Siva Sivabalan Cisco Systems, Inc. 2000 Innovation Drive Kanata, Ontario, K2K 3E8 Canada
EMail: msiva@cisco.com
Vasseur, et al. Standards Track [Page 9] RFC 4561 Definition of RRO Node-Id Sub-Object June 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA).
Vasseur, et al. Standards Track [Page 10]
/data/webs/external/dokuwiki/data/pages/rfc/rfc4561.txt · Last modified: 2006/06/14 16:46 by 127.0.0.1