GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc4455

Network Working Group M. Hallak-Stamler Request for Comments: 4455 Sanrad Intelligent Storage Category: Standards Track M. Bakke

                                                   Cisco Systems, Inc.
                                                           Y. Lederman
                                                Siliquent Technologies
                                                            M. Krueger
                                                       Hewlett-Packard
                                                         K. McCloghrie
                                                   Cisco Systems, Inc.
                                                            April 2006
          Definition of Managed Objects for Small Computer
                  System Interface (SCSI) Entities

Status of This Memo

 This document specifies an Internet standards track protocol for the
 Internet community, and requests discussion and suggestions for
 improvements.  Please refer to the current edition of the "Internet
 Official Protocol Standards" (STD 1) for the standardization state
 and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

 Copyright (C) The Internet Society (2006).

Abstract

 This memo defines a portion of the Management Information Base (MIB),
 for use with network management protocols in the Internet community.
 In particular, it describes managed objects for Small Computer System
 Interface (SCSI) entities, independently of the interconnect
 subsystem layer.

Table of Contents

 1. The Internet-Standard Management Framework ......................3
 2. Requirements Notation ...........................................3
 3. Overview ........................................................3
    3.1. Introduction ...............................................4
    3.2. SCSI Terminology ...........................................6
         3.2.1. SCSI Application Layer ..............................6
         3.2.2. SCSI Device .........................................6
         3.2.3. SCSI Port ...........................................6
         3.2.4. SCSI Initiator Device ...............................7
         3.2.5. SCSI Initiator Port .................................7

Hallak-Stamler, et al. Standards Track [Page 1] RFC 4455 SCSI MIB April 2006

         3.2.6. SCSI Target Device ..................................7
         3.2.7. SCSI Target Port ....................................7
         3.2.8. Logical Units .......................................7
         3.2.9. Logical Unit Number .................................7
         3.2.10. Interconnect Subsystem .............................7
         3.2.11. Device Server ......................................8
         3.2.12. Task Manager .......................................8
         3.2.13. SCSI Instance ......................................8
    3.3. SCSI MIB Module Implementation .............................8
    3.4. Bridging and Virtualization ...............................10
    3.5. SCSI Command MIB Module ...................................11
 4. Structure of the MIB ...........................................11
    4.1. The SCSI Device Group .....................................11
    4.2. The Initiator Group .......................................11
    4.3. The Target Group ..........................................11
    4.4. The Discovery Group .......................................12
    4.5. The LUN Map Group .........................................12
    4.6. The Target Statistic Group ................................12
    4.7. The Target High Speed Statistic Group .....................12
    4.8. The LUN Map Statistics Group ..............................12
    4.9. The LUN Map Statistics High Speed Group ...................13
    4.10. The Initiator Statistics Group ...........................13
    4.11. The Initiator High Speed Statistic Group .................13
    4.12. The Discovery Statistics Group ...........................13
    4.13. The Discovery Statistics High Speed Group ................14
    4.14. The Device Statistics Group ..............................14
 5. Relationships in This MIB ......................................14
 6. Relationship to Other MIBs .....................................16
    6.1. Host Resource MIB .........................................16
    6.2. iSCSI MIB Module ..........................................16
 7. Miscellaneous Details ..........................................16
    7.1. Names and Identifiers .....................................16
    7.2. Logical Unit Number .......................................16
    7.3. Notifications .............................................16
    7.4. SCSI Domains ..............................................17
    7.5. Counters: 32 Bits and 64 Bits .............................17
    7.6. Local versus Remote Entities ..............................18
 8. Abbreviations ..................................................18
 9. Object Definitions .............................................18
 10. Object Population Example: SCSI Target and Initiator
     Devices on a pSCSI Bus ........................................76
    10.1. scsiInstance Table: ......................................77
    10.2. scsiDevice Table: ........................................77
    10.3. scsiPort Table: ..........................................77
    10.4. scsiTransport Table: .....................................77
    10.5. scsiIntrDev Table: .......................................78
    10.6. scsiInitiatorPort Table: .................................78
    10.7. scsiDscTgt Table: ........................................78

Hallak-Stamler, et al. Standards Track [Page 2] RFC 4455 SCSI MIB April 2006

    10.8. scsiDscLUN: ..............................................78
    10.9. scsiDscLUNIdentifier: ....................................79
    10.10. scsiAttTgtPort Table: ...................................79
    10.11. scsiTgtDev Table: .......................................79
    10.12. scsiTgtPort Table: ......................................80
    10.13. scsiLU Table: ...........................................80
    10.14. scsiLuId Table: .........................................80
    10.15. scsiLunMap Table: .......................................81
    10.16. scsiAuthorizedIntr Table: ...............................81
    10.17. scsiAttIntrPort Table: ..................................81
 11. Security Considerations .......................................81
 12. Acknowledgements ..............................................84
 13. IANA Considerations ...........................................84
 14. References ....................................................84
    14.1. Normative References .....................................84
    14.2. Informative References ...................................85

1. The Internet-Standard Management Framework

 For a detailed overview of the documents that describe the current
 Internet-Standard Management Framework, please refer to section 7 of
 RFC 3410 [RFC3410].
 Managed objects are accessed via a virtual information store, termed
 the Management Information Base or MIB.  MIB objects are generally
 accessed through the Simple Network Management Protocol (SNMP).
 Objects in the MIB are defined using the mechanisms defined in the
 Structure of Management Information (SMI).  This memo specifies a MIB
 module that is compliant to the SMIv2, which is described in STD 58,
 RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
 [RFC2580].

2. Requirements Notation

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in [RFC2119].

3. Overview

 This memo defines a portion of the Management Information Base (MIB)
 for use with network management protocols in the Internet community.
 In particular, it describes a set of managed objects to configure and
 monitor Small Computer System Interface entities (SCSI entities),
 i.e., SCSI target devices and SCSI initiator devices and SCSI ports.

Hallak-Stamler, et al. Standards Track [Page 3] RFC 4455 SCSI MIB April 2006

 SCSI is a client-server protocol in which application clients within
 a SCSI initiator device (client) issue service requests to logical
 units contained in a SCSI target device(server).
 This MIB module is based on documents defined by the ANSI T10
 Technical Committee, specifically the SCSI Architecture Model - 2
 [SAM2] and SCSI Primary Commands - 2 [SPC2].
 The [SAM2] standard is the primary source for the SCSI architecture
 discussion in this document and the terminology used in this MIB
 module.

3.1. Introduction

 In the late 1970s, a firm called Shugart Associates started to have
 some considerable success with a peripheral interface definition in
 what became the PC marketplace, and this interface was adopted and
 extended by an open standards committee to form the Small Computer
 Systems Interface (SCSI).  SCSI defines an 8-bit-wide multi-drop
 "bus" structure, which could interconnect a total of eight
 peripherals and computer systems.
 It is important to realize that initially SCSI standardized only the
 "physical connection", i.e., the connectors, cables, and interface
 signals.  Thus, even though a peripheral could be connected to
 multiple systems, the information that flowed across the interface
 was different in each case.  This was addressed some five years later
 by the definition of a Common Command Set, and with this definition
 in place it was possible for the first time to develop a peripheral
 with both a common interface and common operating firmware for
 connection to multiple systems.
 The physical interface of SCSI continued to be developed throughout
 the 1980s with the addition of fast (up to 10 megabytes/s) and wide
 (16 bits) variants, but the distance supported remained a maximum of
 25 meters (from one end of the bus to another), and indeed some of
 the faster variants supported much less than that distance.  The
 command set development continued, with special commands for tapes,
 printers, and even processors being added to the original disk-
 oriented set.  So successful was SCSI in the 1980s that the majority
 of the available Operating Systems incorporated support for the SCSI
 command set as standard.
 However, at the end of the 1980s the distance, speed, and number of
 devices supported by SCSI were starting to become significant
 impediments to systems design, and although the "information
 explosion" had not yet started in earnest, it was already being
 anticipated.  At the same time, the serial interface technologies

Hallak-Stamler, et al. Standards Track [Page 4] RFC 4455 SCSI MIB April 2006

 developed for Local Area Networks such as Ethernet, and the fibre
 optics technologies that were first deployed in telecommunications
 applications were starting to appear sufficiently rugged and low cost
 for use in peripheral interface applications.  Thus, a standards
 project was begun in 1988 to develop a new serial, fibre-optic
 interface to carry the SCSI command sets and other peripheral
 protocols.  This interface eventually became known as Fibre Channel
 (FC), and it is based on an architecture centered around an
 abstractly defined "fabric", which may be a switch or a loop
 connection.  MIB modules for various FC equipments are already in
 existence.
 In order to support the new interfaces, it was necessary to
 completely reorganize the SCSI standards and definitions.  The
 command sets were separated from the physical interface definitions,
 and a SCSI Architectural Model (SAM) was created to define the
 interaction between the various standards.  It is a key to
 understanding SAM to realize that it was first created approximately
 10 years AFTER the first SCSI products were shipped!
 The most recent development in this saga occurred in 2000 when an
 IETF Working Group was formed to address, among other things, a
 definition for transporting the SCSI command sets directly over a
 TCP/IP infrastructure.  This effort is known as iSCSI [RFC3720], and
 an iSCSI MIB module is already under development [ISCSI].
 Most of the projects are in T10, except Fibre Channel, which is
 defined by T11 and IEEE defines 1394.
 The SCSI MIB module represents the SCSI protocol layer common to all
 SCSI command sets and transports.  It does not represent the command
 sets and transports themselves.  These should appear in other MIB
 modules specific to the transport or command set.  The following
 illustration shows the relationships between the various actual and
 possible SCSI-related MIB modules.

Hallak-Stamler, et al. Standards Track [Page 5] RFC 4455 SCSI MIB April 2006

                   +---------------------------------+
     SCSI Command  | Higher-level MIBs, specific to  |
     Sets          | command sets, disk, tape, etc.  |
                   +---------------------------------+
     SCSI          |             SCSI MIB            |
                   +-------+---------+-------+-------+
     SCSI          | iSCSI |   FCP   |  SPI  | Other |
     Transport     |  MIB  |   MIB   |  MIB  |  MIBs |
     Protocols     |       |         |       |       |
                   +-------+---------+-------+-------+
     SCSI          |  TCP  |  Fibre  |    Other      |
     Interconnect  |  MIB  | Channel | Interconnect  |
                   |       |  MIBs   |    MIBs       |
                   +-------+---------+---------------+
 An iSCSI MIB module [ISCSI] and a Fibre Channel interconnect MIB
 module [RFC4044] are currently being developed.  No development is
 currently planned for standard command-set-specific or device-
 specific MIBs.
 The TCP-MIB [RFC4022] is already a proposed standard RFC 4022.

3.2. SCSI Terminology

 The following sections explain some of the SCSI terminology, which is
 used later in defining the MIB module.  For the authoritative
 definitions of these terms, see SAM-2 [SAM2].

3.2.1. SCSI Application Layer

 The protocols and procedures that implement or invoke SCSI commands
 and task management functions by using services provided by a SCSI
 transport protocol layer.

3.2.2. SCSI Device

 A SCSI device is an entity that contains one or more SCSI ports that
 are connected to a service delivery subsystem and supports a SCSI
 application protocol.

3.2.3. SCSI Port

 A SCSI port is a device-resident entity that connects the application
 client, device server, or task manager to the service delivery
 subsystem through which requests and responses are routed.  A SCSI
 port is synonymous with port and either a SCSI initiator port or a
 SCSI target port.

Hallak-Stamler, et al. Standards Track [Page 6] RFC 4455 SCSI MIB April 2006

3.2.4. SCSI Initiator Device

 A SCSI initiator device contains application clients and SCSI
 initiator ports that originate device service and task management
 requests to be processed by a SCSI target device.  When used, this
 term refers to SCSI initiator devices or SCSI target/initiator
 devices that are using the SCSI target/initiator port as a SCSI
 initiator port.

3.2.5. SCSI Initiator Port

 A SCSI initiator port acts as the connection between application
 clients and the service delivery subsystem through which requests and
 responses are routed.  In all cases when this term is used, it refers
 to an initiator port or a SCSI target/initiator port operating as a
 SCSI initiator port.

3.2.6. SCSI Target Device

 A SCSI target device contains logical units and SCSI target ports
 that receive device service and task management requests for
 processing.  When used, this term refers to SCSI target devices or
 SCSI target/initiator devices that are using the SCSI
 target/initiator port as a SCSI target port.

3.2.7. SCSI Target Port

 A SCSI target port contains a task router and acts as the connection
 between device servers and task managers and the service delivery
 subsystem through which requests and responses are routed.  When this
 term is used, it refers to a SCSI target port or a SCSI
 target/initiator port operating as a SCSI target port.

3.2.8. Logical Units

 A logical unit is an entity residing in the SCSI target device that
 implements a device model and processes SCSI commands sent by an
 application client.

3.2.9. Logical Unit Number

 A Logical Unit Number or LUN is a 64-bit identifier for a logical
 unit.

3.2.10. Interconnect Subsystem

 An interconnect subsystem is one or more interconnects that appear as
 a single path for the transfer of information between SCSI devices.

Hallak-Stamler, et al. Standards Track [Page 7] RFC 4455 SCSI MIB April 2006

3.2.11. Device Server

 A device server is an object within the logical unit that processes
 SCSI tasks according to the rules for task management.

3.2.12. Task Manager

 A task manager is a server within the SCSI target device that
 processes task management functions.

3.2.13. SCSI Instance

 A "SCSI instance" is a distinct SCSI entity within a managed system.
 Whereas most implementations will have just one SCSI instance, the
 MIB module allows for multiple (virtual) instances, such that a large
 system can be "partitioned" into multiple, distinct virtual systems.
 For example, in a host, it allows multiple vendors' implementations
 of the MIB module to co-exist under a single SNMP agent through each
 vendor's implementation being a different SCSI instance.  It also
 allows a single SNMP agent to represent multiple subsystems each of
 which has its own SCSI instance.

3.3. SCSI MIB Module Implementation

 The SCSI MIB module is a basic building block to use in the various
 SCSI management scenarios.  This module is intended to be implemented
 in every SCSI entity in a managed system.  A SCSI entity can be a
 SCSI initiator device, SCSI target device or SCSI initiator and
 Target device.  Since SCSI (storage) networking devices may contain
 more than one SCSI entity, it is possible that more than one SCSI
 instance will reside in a single device.
 In small-scale environments, a single network management station
 (NMS) may have SNMP access to both SCSI initiator devices and SCSI
 target devices.  However, if the SCSI target devices, or virtualized
 target devices, are being provided as a service, it is more likely
 that the provider of the service owns and manages the SCSI target
 devices and that the consumer of the service owns and manages the
 SCSI initiator devices.  In this case, the service provider NMS and
 the consumer NMS may have only allowed SNMP access to the SCSI target
 devices and the SCSI initiator devices, respectively.
 The figures in this chapter describe the location of the SCSI MIB
 module implementations in the various SCSI management scenarios.  The
 locations of the SCSI SNMP agent implementing the SCSI MIB module are
 denoted with '*'.

Hallak-Stamler, et al. Standards Track [Page 8] RFC 4455 SCSI MIB April 2006

  +----------+                                       +---------+
  |SCSI      |          SCSI Transport               |SCSI     |
  |Initiator +---------------------------------------+Target   |
  |Device    |                                       |Device   |
  |     *    |                                       |    *    |
  +----------+                                       +---------+
        |                                                 |
        |                                                 |
        |                                                 |
        |                                                 |
        |                                                 |
        |      SNMP        +----------+     SNMP          |
        +------------------|SCSI      |-------------------+
                           |Management|
                           | (NMS)    |
                           +----------+
   Figure 1.  Single SCSI Initiator Device and
              Single SCSI Target Device
 Figure 1 describes a simple SCSI management scenario of a SCSI
 initiator device, a SCSI target device, and a management station.  In
 this scenario, there are two SNMP agents, each containing its SCSI
 instance and its respective objects.  As the SCSI target device and
 SCSI initiator device are interconnected, their target and initiator
 port objects will be complementary.
 +-----------+
 |  +--------+-+          SCSI Transport               +---------+
 |  | SCSI     |---------------------------------------+ SCSI    |
 |* | Initiator+---------------------------------------+ Target  |
 +--| Device   |          SCSI Transport               | Device  |
  | |     *    |                                       |    *    |
  | +----------+                                       +---------+
  |       |                                                 |
  |       |                                                 |
  |       |                                                 |
  |       |                                                 |
  |       |                                                 |
  |SNMP   |      SNMP        +----------+     SNMP          |
  +-------+------------------|SCSI      |-------------------+
                             |Management|
                             | (NMS)    |
                             +----------+
   Figure 2.  Multiple Hosts and a Single Target Device

Hallak-Stamler, et al. Standards Track [Page 9] RFC 4455 SCSI MIB April 2006

 Figure 2 adds another SCSI initiator device, to the SCSI network,
 which connects to the same SCSI target device.  The additional SCSI
 initiator device also has an SNMP agent implementing the SCSI MIB
 module.  In this case, the SCSI target device's MIB module will show
 that two SCSI initiator devices are attached to it.
 +-----------+                                          +----------+
 |  +----------+              +---------------+       +-+-------+  |
 |  |SCSI      |--------------| Virtualization|       | SCSI    |  |
 |* |Initiator +--------------| Device        +-------+ Target  |  |
 +--|Device    | SCSI         |               |       | Device  | *|
  | |     *    |              |            *  |       |    *    |--+
  | +----------+ Transport    +------------+--+       +---------+ |
  |       |                                |              |       |
  |       |                                |              |       |
  |       |                                |              |       |
  |       |                                |              |       |
  |       |                                |              |       |
  |       |      SNMP        +-----------+ |   SNMP       |       |
  +-------+------------------+ SCSI      + +-+------------+-------+
                             | Management|
                             | (NMS)     |
                             +-----------+
   Figure 3.  Multiple Hosts, Virtualization Device and Multiple SCSI
              Target Devices
 Figure 3 adds an in-band virtualization device that encapsulates, and
 possibly modifies, the SCSI target devices' representation to the
 SCSI Initiator devices.  It is common practice for an in-band
 virtualization device to include both SCSI target and initiator
 device functionality.  Therefore, its SCSI MIB module implementation
 includes both the SCSI Target device and Initiator device objects.
 It should be noted that the Virtualization device might implement
 additional proprietary MIB modules, as the SCSI MIB module does not
 distinguish between physical and virtual SCSI entities.

3.4. Bridging and Virtualization

 Storage virtualization is a concept that abstracts storage resources
 in such a way that, storage entities are provided as pool of logical
 entities.
 Usually, the virtualization process is transparent to the storage
 users (i.e., hosts).  Virtualization normally affects the SCSI
 entities represented to SCSI initiator devices.  However, the SCSI
 MIB module enables the representation of SCSI entities and their
 respective status, including error and performance-monitoring

Hallak-Stamler, et al. Standards Track [Page 10] RFC 4455 SCSI MIB April 2006

 statistics.  It should be possible to perform a limited number of
 configuration modification and diagnostic actions.
 The SCSI entities embodied in the bridging and virtualization devices
 can be represented by the SCSI MIB module.  However, the
 configuration of bridging and virtualization devices is beyond the
 above-described scope and therefore should be provided through other
 MIB modules.

3.5. SCSI Command MIB Module

 The management of SCSI commands is beyond the scope of this MIB
 module.  Future SCSI Command MIB module can link to this MIB module,
 through the use of Object Identifiers (OIDs) or INDEX values of
 appropriate tables.

4. Structure of the MIB

 This MIB module contains fourteen conformance groups:

4.1. The SCSI Device Group

 The scsiDeviceGroup group contains the objects general to each SCSI
 instance: instance, device, and port objects.  It contains also the
 objects referring to the transport(s) used by those SCSI instances.
 This group is mandatory for all SCSI managed system.
 Alias objects are provided for SCSI instances and SCSI devices to
 enable administrators to identify them.  These objects contain
 human-readable administrative text strings, and hence use the
 SnmpAdminString textual convention from [RFC3411].

4.2. The Initiator Group

 The scsiInitiatorDeviceGroup contains all the managed information
 related to a local SCSI initiator device and port.  In addition, it
 contains the managed objects referring to the monitored attached SCSI
 target devices.  Any managed system acting as a SCSI initiator or
 target/initiator device and port MUST support this group.

4.3. The Target Group

 The scsiTargetDeviceGroup contains all the managed objects related to
 a local SCSI target device, a local SCSI target port, monitored
 attached initiator ports, logical units, and logical unit
 identifiers.

Hallak-Stamler, et al. Standards Track [Page 11] RFC 4455 SCSI MIB April 2006

 Managed systems acting as a SCSI target or target/initiator device
 and port must support this group.

4.4. The Discovery Group

 The scsiDiscoveryGroup group is a collection of managed objects
 referring to remote SCSI target devices, remote SCSI target ports,
 remote logical units, and remote logical unit identifiers discovered
 by or configured to a managed system acting as a SCSI initiator
 device.
 Managed systems acting as a SCSI initiator device and port and
 supporting remote SCSI target devices or ports configuration or
 discovery should implement this group.

4.5. The LUN Map Group

 The scsiLunMapGroup group is a collection of managed objects allowing
 mapping between SCSI target devices, logical units, and logical unit
 numbers in one side to remote authorized SCSI initiator devices or
 ports in another side.
 Managed systems supporting this mapping should implement the
 scsiLunMapGroup.

4.6. The Target Statistic Group

 The scsiTargetDevStatsGroup group is a collection of managed objects
 representing various statistics referring to a SCSI target device or
 port.  Managed systems acting as a SCSI target device and port
 supporting statistics should implement this group.

4.7. The Target High Speed Statistic Group

 The scsiTargetDevHSStatsGroup group is a collection of managed
 objects representing various statistics referring to a SCSI target
 device or port.  It provides support for systems that can quickly
 generate countable information because they run at high speed.
 Managed systems acting as a SCSI target device and port and running
 at high speed supporting should implement this group.

4.8. The LUN Map Statistics Group

 The scsiLunMapStatsGroup group is a collection of managed objects
 representing various statistics referring to remote authorized SCSI
 initiator devices or ports.

Hallak-Stamler, et al. Standards Track [Page 12] RFC 4455 SCSI MIB April 2006

 Managed systems acting as a SCSI target device and port and able to
 gather statistics on remote SCSI initiator devices or ports should
 implement this group.

4.9. The LUN Map Statistics High Speed Group

 The scsiLunMapHSStatsGroup group is a collection of managed objects
 representing various statistics referring to remote authorized SSCI
 initiator devices or ports.  It provides support for systems that can
 quickly generate countable information because they run at high
 speed.
 Managed systems acting as a SCSI target device and port and able to
 gather statistics on remote SCSI initiator devices or ports and
 running at high speed should implement this group.

4.10. The Initiator Statistics Group

 The scsiInitiatorDevStatsGroup group is a collection of managed
 objects representing various statistics referring to a SCSI initiator
 device or port.
 Managed systems acting as a SCSI initiator device and port supporting
 statistics should implement this group.

4.11. The Initiator High Speed Statistic Group

 The scsiInitiatorDevHSStatsGroup group is a collection of managed
 objects representing various statistics referring to a SCSI initiator
 device or port.  It provides support for systems that can quickly
 generate countable information because they run at high speed.
 Managed systems acting as a SCSI initiator device and port and
 running at high speed supporting should implement this group.

4.12. The Discovery Statistics Group

 The scsiDiscoveryStatsGroup group is a collection of managed objects
 representing various statistics referring to remote discovered or
 configured SCSI target devices or ports.
 Managed systems acting as a SCSI initiator device and port and able
 to gather statistics on remote SCSI target devices or ports should
 implement this group.

Hallak-Stamler, et al. Standards Track [Page 13] RFC 4455 SCSI MIB April 2006

4.13. The Discovery Statistics High Speed Group

 The scsiDiscoveryHSStatsGroup group is a collection of managed
 objects representing various statistics referring to remote
 discovered or configured SCSI target devices or ports.  It provides
 support for systems that can quickly generate countable information
 because they run at high speed.
 Managed systems acting as a SCSI initiator device and port and able
 to gather statistics on remote SCSI target devices or ports and
 running at high speed should implement this group.

4.14. The Device Statistics Group

 The scsiDeviceStatGroup group is a collection of managed objects
 representing various statistics referring to a SCSI device.
 Managed systems able to gather device statistics should implement
 this group.

5. Relationships in This MIB

 This section outlines the functionality and the dependency between
 the MIB tables providing the required management functionality for
 SCSI initiator and target devices.  For specific usage of these
 tables, the reader should refer to the description of the tables and
 their respective table entries and attributes.
 Following is a list of required SCSI initiator-related features, and
 the respective tables facilitating this functionality:
 o  List all the SCSI initiator ports that should be managed through
    this MIB module.  The table scsiIntrPortTable maintains all the
    SCSI initiator ports for the SCSI initiator devices in the MIB
    module.
 o  Provide a list of all SCSI target ports or SCSI target devices to
    which a SCSI initiator port can attach.  This should prevent a
    SCSI initiator device or port from attaching to SCSI target
    devices that should be either invisible or inaccessible to it.
    The entries in this list can be created either manually or by
    automatic discovery mechanisms (e.g., SLP, iSNS).  The
    ScsiDscTgtTable provides this information.  The entries in this
    table point to the SCSI initiator port, and indicate that the SCSI
    initiator port can only attach to SCSI target ports or SCSI target
    devices provided in the respective entries of the ScsiDscTgtTable.

Hallak-Stamler, et al. Standards Track [Page 14] RFC 4455 SCSI MIB April 2006

    This MIB module permits, but does not require, this table to be
    written via SNMP.  There are significant security considerations
    in allowing writes to this table; see Section 11.
 o  The information, for the aforementioned SCSI target ports or SCSI
    target devices, about the LUs and their respective LUN Ids should
    be provided.  The scsiDscLunTable and scsiDscLunIdTable maintain
    this information.
 o  The scsiAttTgtPortTable provides the information about the SCSI
    target ports each SCSI initiator port is currently communicating
    with.  This table should be dynamically updated to reflect those
    connections.
 Following is a list of required SCSI target device-related features,
 and the respective tables facilitating this functionality:
 o  List all the SCSI target ports that should be managed through this
    MIB module.  The table scsiTgtPortTable maintains all the SCSI
    target ports for the SCSI target devices in the MIB module.
 o  Provide a list of valid SCSI initiator ports or SCSI initiator
    devices authorized to attach to a SCSI target port.  This list
    should feature the concept of "access lists", which are common in
    IP routers and switches.  The ScsiAuthorizedIntr table provides
    this information.  This MIB module permits, but does not require
    this table to be written via SNMP.  There are significant security
    considerations in allowing writes to this table; see Section 11.
 o  It should be possible to specify the list of LUNs exposed to each
    SCSI initiator port or device, when it is attached to the SCSI
    target device.  SCSI target devices must provide a default list of
    LUNs.  This list of LUNs can either be a unique list for each SCSI
    initiator device or be the default list.  For each entry in the
    ScsiAuthorizedIntr table, a pointer, named
    scsiAuthIntrLunMapIndex, indexing the ScsiLunMapTable facilitates
    this feature.
 o  Provide means to monitor all the SCSI initiator ports currently
    attached to this SCSI target port.  The scsiAttIntrPortTable
    provides this information.  This table should be dynamically
    updated to reflect those connections.

Hallak-Stamler, et al. Standards Track [Page 15] RFC 4455 SCSI MIB April 2006

6. Relationship to Other MIBs

6.1. Host Resource MIB

 The SCSI MIB module extends objects defined in the host resource MIB
 module to SCSI-specific entities but does not contain information on
 software modules such as device drivers.  If MIB objects are required
 for installed packages of SCSI software, then the hrSWInstalledGroup
 of the Host Resources MIB [RFC2790] are the standard MIB objects to
 use.

6.2. iSCSI MIB Module

 The SCSI MIB module defines managed objects for the SCSI protocol
 layer.  The SCSI layer can run on top of several transport layers;
 iSCSI is one of them.  The ISCSI-MIB [ISCSI] is the MIB portion
 defining the managed objects for the transport called iSCSI.  In the
 same way, a fibre channel or parallel SCSI MIB module would define
 managed objects for a transport called, respectively, fibre channel
 or parallel SCSI.
 The relationship between the SCSI MIB module and any valid transport
 MIB module is determined via the SCSI port managed table that has an
 object pointing to the corresponding row, if any, of the relevant
 table in a transport MIB module.

7. Miscellaneous Details

7.1. Names and Identifiers

 The names and the identifiers of the SCSI devices, ports, and logical
 units depend on the underlying transport protocols; their format and
 length vary accordingly.  Please refer to SAM-2 [SAM2] for more
 details.

7.2. Logical Unit Number

 The Logical Unit Number is a 64-bit integer.  This type does not
 exist in SMI and therefore, this MIB contains a textual convention
 defining LUN as an OCTET STRING.

7.3. Notifications

 Separate SNMP notifications may be enabled/disabled to notify of a
 change in any of the SCSI device status variables.  A notification
 will be generated theoretically for each occurrence (see restriction

Hallak-Stamler, et al. Standards Track [Page 16] RFC 4455 SCSI MIB April 2006

 below) of the abnormal status (e.g., if the SCSI device's current
 status is abnormal and another logical unit changes its status from
 available to abnormal another notification will occur).
 To avoid sending an excessive number of notifications due to multiple
 errors counted, an SNMP agent implementing the SCSI MIB module should
 not send more than three SCSI notifications in any 10-second period.
 The 3-in-10 rule was chosen because one notification every three
 seconds was deemed often enough, but if and when two or three
 different notifications happen at the same time, it would not be
 desirable to suppress them.  Three notifications in 10 seconds is a
 happy medium, where a short burst of notifications is allowed,
 without inundating the network and/or destination host with a large
 number of notifications.
 The ultimate control on sending of notifications is in command of the
 notification generator module specified in [RFC3413].

7.4. SCSI Domains

 SAM-2 [SAM2] specifies that devices belong to a domain.  However, it
 is not usually possible to determine this from within a system, so
 domains are not represented within this MIB module.

7.5. Counters: 32 Bits and 64 Bits

 Some counters, in (newer) high-performance systems, can increase at a
 fast enough rate such that their representation as Counter32s can
 cause them to "wrap" in less than an hour.  The SMIv2 provides
 Counter64 as the syntax for such counters.  However, (older) SNMPv1
 implementations cannot support Counter64s.  Thus, this MIB module
 defines such counters as both Counter32s and Counter64's.
 The counters in this MIB module that count data are defined in terms
 of megabytes (i.e., as the number of megabytes of data), such that
 Counter64s are not required.
 However, the counters in this MIB module that count commands, when in
 use at 5 GBit/second with 512-byte read/write operations, could wrap
 within an hour.  Therefore, each of these counters will be defined as
 both a Counter32 and a Counter64, with the latter being mandatory,
 for system speeds of 4 Gbit/second or higher.
 A possible (but not required) implementation strategy is to have the
 value of each Counter32 be the same value as the low-order 32 bits of
 the corresponding Counter64.

Hallak-Stamler, et al. Standards Track [Page 17] RFC 4455 SCSI MIB April 2006

7.6. Local versus Remote Entities

 This MIB module qualifies often SCSI entities as local or remote.
 The local entities are the ones for which the agent is reporting.
 The remote entities are the ones that the local entities are in
 communication with via the SCSI protocol.

8. Abbreviations

 This MIB module will use the following abbreviations:
    Inst = Instance
    Dev = SCSI Device
    Tgt = SCSI Target Device
    Intr = SCSI Initiator Device
    Att = Attached
    Id = Identifier
    Dsc = Discovered
    pSCSI = Parallel SCSI

9. Object Definitions

 SCSI-MIB DEFINITIONS ::= BEGIN
    IMPORTS
    MODULE-IDENTITY, OBJECT-IDENTITY, OBJECT-TYPE,
    NOTIFICATION-TYPE, Integer32, Unsigned32, Counter32,
    Counter64, Gauge32,
    mib-2                                     FROM SNMPv2-SMI
    TEXTUAL-CONVENTION, TimeStamp, TruthValue,
    RowStatus, RowPointer, AutonomousType,
    StorageType                               FROM SNMPv2-TC
    MODULE-COMPLIANCE, OBJECT-GROUP,
    NOTIFICATION-GROUP                        FROM SNMPv2-CONF
    SnmpAdminString                  FROM SNMP-FRAMEWORK-MIB;
 scsiMIB MODULE-IDENTITY
      LAST-UPDATED "200603300000Z"        -- 30th March 2006
      ORGANIZATION "IETF"
      CONTACT-INFO "
           Michele Hallak-Stamler

Hallak-Stamler, et al. Standards Track [Page 18] RFC 4455 SCSI MIB April 2006

           Sanrad Intelligent Network
           27 Habarzel Street
           Tel Aviv, Israel
           Phone: +972 3 7674809
           E-mail: michele@sanrad.com
           Yaron Lederman
           Siliquent Technologies Ltd.
           21 Etzel Street
           Ramat Gan, Israel
           Phone: +972 54 5308833
           E-mail: yaronled@bezeqint.net
           Mark Bakke
           Postal: Cisco Systems, Inc
           7900 International Drive, Suite 400
           Bloomington, MN
           USA 55425
           E-mail: mbakke@cisco.com
           Marjorie Krueger
           Postal: Hewlett-Packard
           8000 Foothills Blvd.
           Roseville, CA 95747
           E-mail: marjorie_krueger@hp.com
           Keith McCloghrie
           Cisco Systems, Inc.
           Postal: 170 West Tasman Drive
           San Jose, CA USA 95134
           Phone: +1 408 526-5260
           E-mail: kzm@cisco.com
          "
      DESCRIPTION
           "The SCSI MIB Module.
           Copyright (C) The Internet Society (2006).  This version of
           this MIB module is part of RFC 4455; see the RFC
           itself for full legal notices."
  1. - Revision History
      REVISION     "200603300000Z"
      DESCRIPTION  " Initial version published as RFC 4455."
 ::= { mib-2 139}
  1. - Textual Conventions

ScsiLUN ::= TEXTUAL-CONVENTION

Hallak-Stamler, et al. Standards Track [Page 19] RFC 4455 SCSI MIB April 2006

      STATUS current
      DESCRIPTION
         "This textual convention represents a SCSI Logical Unit
         Number (LUN).  The format of a LUN is documented in Tables
         A.2 and A.3 of SAM-2 [SAM2]."
      REFERENCE
       "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003,
       T10 Project 1157-D, 12 September 2002 - Annex A [SAM2]"
      SYNTAX OCTET STRING (SIZE ( 2 | 8))
 ScsiIndexValue ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
         "An arbitrary integer value, greater than zero, for use
         as a unique index value."
      SYNTAX Unsigned32 (1..4294967295)
 ScsiPortIndexValueOrZero ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
       "This textual convention is an extension of the ScsiIndexValue
        convention.  The latter defines a greater than zero value used
        to identify an index.  This extension permits the additional
        value of zero and is applicable only to indices of SCSI port.
        Usage of the zero is object-specific and must therefore be
        defined as part of the description of any object that uses
        this syntax.  Examples of the usage of zero might include
        situations where the index was unknown, or when none or all
        indices need to be referenced."
      SYNTAX Unsigned32 (0..4294967295)
 ScsiIndexValueOrZero ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
       "This textual convention is an extension of the ScsiIndexValue
        convention.  The latter defines a greater than zero value used
        to identify an index.  This extension permits the additional
        value of zero.  Usage of the zero is object-specific and must
        therefore be defined as part of the description of any object
        that uses this syntax.  Examples of the usage of zero might
        include situations where index was unknown, or when none or
        all indices need to be referenced."
      SYNTAX Unsigned32 (0..4294967295)
 ScsiIdentifier ::= TEXTUAL-CONVENTION

Hallak-Stamler, et al. Standards Track [Page 20] RFC 4455 SCSI MIB April 2006

      STATUS current
      DESCRIPTION
        "This textual convention represents a generic SCSI port
        identifier.
        The format depends on the transport used and is documented
        in Tables A.2 and A.3 of SAM-2 [SAM2]."
      REFERENCE
       "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003,
       T10 Project 1157-D, 12 September 2002 - Annex A [SAM2]"
      SYNTAX OCTET STRING (SIZE (0..262))
 ScsiName ::= TEXTUAL-CONVENTION
      STATUS current
      DESCRIPTION
        "This textual convention represents the name of a SCSI
        initiator device, a SCSI target device, a SCSI initiator port
        or a SCSI target port.
        The format depends on the transport used and is documented
        in Tables A.4 and A.5 of SAM-2 [SAM2].
       Every object defined using this syntax must define whether it
       is
       a) always used for a port,
       b) always used for a device, or
       c) the circumstances under which it is used for a port or
       device."
      REFERENCE
       "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003,
       T10 Project 1157-D, 12 September 2002 - Annex A [SAM2]"
      SYNTAX OCTET STRING (SIZE (0..262))
 ScsiLuNameOrZero  ::= TEXTUAL-CONVENTION
      STATUS current
      DESCRIPTION
        "This textual convention represents either the name of a SCSI
        logical unit or a zero-length string.  Objects defined with
        this syntax must specify the meaning of the zero-length
        string.
        The format of the name of a LU is defined as:
        - a zero-length octet string or
        - a string of eight bytes."
      REFERENCE
       "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003,
       T10 Project 1157-D, 12 September 2002 - Annex A [SAM2]"
      SYNTAX OCTET STRING (SIZE (0 | 8))
 ScsiDeviceOrPort ::= TEXTUAL-CONVENTION

Hallak-Stamler, et al. Standards Track [Page 21] RFC 4455 SCSI MIB April 2006

      STATUS current
      DESCRIPTION
        "This type specifies whether a particular configuration is
        applicable to a port or to a device."
      SYNTAX INTEGER  {
          device(1),
          port(2),
          other(3)
       }
 ScsiIdCodeSet ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
        "This textual convention specifies the code set for the
        identifier contained in an Identification Descriptor returned
        in a logical unit's Device Identification Page, and is
        formatted as defined in T10 SPC-2 (see REFERENCE) Table 172 -
        Code Set"
      REFERENCE
        "ANSI - SCSI Primary Commands - 2 (SPC-2),
        ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4,
        Vital Product Data Parameters [SPC2]"
      SYNTAX Unsigned32 (0..15)
 ScsiIdAssociation ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
        "This textual convention specifies what the identifier is
        associated with (e.g., with the addressed physical/logical
        device or with a particular port) for the identifier
        contained in an Identification Descriptor returned in a
        logical unit's Device Identification Page, and is
        formatted as defined in T10 SPC-2 (see REFERENCE)
        Table 173 - Association."
      REFERENCE
        "ANSI - SCSI Primary Commands - 2 (SPC-2),
        ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4,
        Vital Product Data Parameters [SPC2]"
      SYNTAX Unsigned32 (0..3)
 ScsiIdType ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
       "This textual convention specifies the type for the identifier
        contained in an Identification Descriptor returned in a

Hallak-Stamler, et al. Standards Track [Page 22] RFC 4455 SCSI MIB April 2006

        logical unit's Device Identification Page, and is formatted
        as defined in T10 SPC-2 (see REFERENCE) table 174 - Identifier
        Type."
      REFERENCE
        "ANSI - SCSI Primary Commands - 2 (SPC-2),
        ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4,
        Vital Product Data Parameters [SPC2]"
      SYNTAX Unsigned32 (0..15)
 ScsiIdValue ::= TEXTUAL-CONVENTION
      STATUS current
      DESCRIPTION
       "This textual convention represents an identifier.  The objects
        of type ScsiIdCodeSet, ScsiIdAssociation, ScsiIdType define
        together the format.
        The format is the same as contained in an Identification
        Descriptor returned in a logical unit's Device Identification
        Page, and is formatted as defined in T10 SPC-2
        (see REFERENCE)."
     REFERENCE
        "ANSI - SCSI Primary Commands - 2 (SPC-2),
        ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4,
        Vital Product Data Parameters [SPC2]"
      SYNTAX OCTET STRING (SIZE (0..255))
 ScsiHrSWInstalledIndexOrZero ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS current
      DESCRIPTION
        "The index value for a software module's row in the Host
        Resources MIBs hrSWInstalledTable.  A zero value indicates
        that no row in the hrSWInstalledTable is applicable."
      REFERENCE
        "hrSWInstalledTable is defined in the Host Resources MIB,
        [RFC2790]."
      SYNTAX   Integer32 (0..2147483647)
  1. - Structure of the MIB

scsiNotifications OBJECT IDENTIFIER ::= { scsiMIB 0 }

 scsiAdmin         OBJECT IDENTIFIER ::= { scsiMIB 1 }
 scsiObjects       OBJECT IDENTIFIER ::= { scsiMIB 2 }
 scsiConformance   OBJECT IDENTIFIER ::= { scsiMIB 3 }
 scsiTransportTypes   OBJECT IDENTIFIER ::= { scsiAdmin 1 }
 scsiGeneral          OBJECT IDENTIFIER ::= { scsiObjects 1 }
 scsiInitiatorDevice  OBJECT IDENTIFIER ::= { scsiObjects 2 }
 scsiTargetDevice     OBJECT IDENTIFIER ::= { scsiObjects 3 }

Hallak-Stamler, et al. Standards Track [Page 23] RFC 4455 SCSI MIB April 2006

 scsiLogicalUnit      OBJECT IDENTIFIER ::= { scsiObjects 4 }
  1. - Transport Types *
  2. - The following object identifiers allow determining the different
  3. - transports (service delivery subsystems) in use under the SCSI
  4. - layer.
 scsiTransportOther   OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies a transport that has no identity; it
      might happen because the transport is unknown or might not
      have been defined when this MIB module was created."
 ::= { scsiTransportTypes 1 }
 scsiTransportSPI     OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies a parallel SCSI transport."
    REFERENCE
      "T10 - SCSI Parallel Interface - 4 (SPI-4)
      - ANSI INCITS 362-2002 [SPI4]"
 ::= { scsiTransportTypes 2 }
 scsiTransportFCP     OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies a Fibre Channel Protocol for SCSI,
      Second Version."
    REFERENCE
      "T10 - SCSI Fibre Channel Protocol - 2 (FCP-2)
      - ANSI INCITS 350-2003 [FCP2]"
 ::= { scsiTransportTypes 3 }
 scsiTransportSRP  OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies a protocol for transporting SCSI over
      Remote Direct Memory Access (RDMA) interfaces, e.g., InfiniBand
      (tm)."
    REFERENCE
      "T10 - SCSI RDMA Protocol (SRP)
       - ANSI INCITS 365-2002 [SRP]."
 ::= { scsiTransportTypes 4 }
 scsiTransportISCSI   OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION

Hallak-Stamler, et al. Standards Track [Page 24] RFC 4455 SCSI MIB April 2006

      "This identity identifies an iSCSI transport."
    REFERENCE
      "IETF IPS WG - Internet Small Computer Systems Interface
       (iSCSI) [RFC3720] "
 ::= { scsiTransportTypes 5 }
 scsiTransportSBP  OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies the Serial Bus Protocol 3."
    REFERENCE
      "T10 - Serial Bus Protocol 3 (SBP-3)
      - ANSI INCITS 375-2004 [SBP3]."
 ::= { scsiTransportTypes 6 }
 scsiTransportSAS  OBJECT-IDENTITY
    STATUS   current
    DESCRIPTION
      "This identity identifies the Serial Attach SCSI Protocol."
    REFERENCE
      "T10 - Serial Attached SCSI - 1.1 (SAS - 1.1)
      - #1601-D Rev-10 [SAS-1.1]."
 ::= { scsiTransportTypes 7 }
  1. - Instance Table * scsiInstanceTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SCSI instances present on the system. The SCSI instance is the top-level entity, to which everything else belongs. An SNMP agent could represent more than one instance if it represents either a stack of devices, or virtual partitions of a larger device, or a host running multiple SCSI implementations from different vendors." ::= { scsiGeneral 1 } scsiInstanceEntry OBJECT-TYPE SYNTAX ScsiInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular SCSI instance." INDEX { scsiInstIndex } ::= { scsiInstanceTable 1 } Hallak-Stamler, et al. Standards Track [Page 25] RFC 4455 SCSI MIB April 2006 ScsiInstanceEntry ::= SEQUENCE { scsiInstIndex ScsiIndexValue, scsiInstAlias SnmpAdminString, scsiInstSoftwareIndex ScsiHrSWInstalledIndexOrZero, scsiInstVendorVersion SnmpAdminString, scsiInstScsiNotificationsEnable TruthValue, scsiInstStorageType StorageType } scsiInstIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary integer used to uniquely identify a particular SCSI instance." ::= { scsiInstanceEntry 1 } scsiInstAlias OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..79)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents an administrative string, configured by the administrator. It can be a zero-length string." ::= { scsiInstanceEntry 2 } scsiInstSoftwareIndex OBJECT-TYPE SYNTAX ScsiHrSWInstalledIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "If this management instance corresponds to an installed software module, then this object's value is the value of the hrSWInstalledIndex of that module. If there is no correspondence to an installed software module (or no module that has an hrSWInstalledIndex value), then the value of this object is zero." REFERENCE "hrSWInstalledIndex is defined in the Host Resources MIB, [RFC2790]." ::= { scsiInstanceEntry 3 } scsiInstVendorVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION Hallak-Stamler, et al. Standards Track [Page 26] RFC 4455 SCSI MIB April 2006 "This object represents a text string set by the manufacturer describing the version of this instance. The format of this string is determined solely by the manufacturer and is for informational purposes only. It is unrelated to the SCSI specification version numbers." ::= { scsiInstanceEntry 4 } scsiInstScsiNotificationsEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether notifications defined in this MIB module will be generated." DEFVAL { true } ::= { scsiInstanceEntry 5 } scsiInstStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the memory realization for this SCSI entity. Specifically, each row in the following tables: scsiIntrDevTable scsiDscTgtTable scsiAuthorizedIntrTable scsiLunMapTable has a StorageType as specified by the instance of this object that is INDEXed by the same value of scsiInstIndex. This value of this object is also used to indicate the persistence across reboots of writable values in its row of the scsiInstanceTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row, nor to any object belonging to a table whose entry is INDEXed by the same value of scsiInstIndex." DEFVAL { nonVolatile } ::= { scsiInstanceEntry 6 } – Device Table scsiDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiDeviceEntry Hallak-Stamler, et al. Standards Track [Page 27] RFC 4455 SCSI MIB April 2006 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SCSI devices contained in each of the SCSI manageable instances that this agent is reporting." ::= { scsiGeneral 2 } scsiDeviceEntry OBJECT-TYPE SYNTAX ScsiDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular SCSI device included in this SCSI manageable instance identifiable by the value of scsiInstIndex." INDEX {scsiInstIndex, scsiDeviceIndex} ::= { scsiDeviceTable 1 } ScsiDeviceEntry ::= SEQUENCE { scsiDeviceIndex ScsiIndexValue, scsiDeviceAlias SnmpAdminString, scsiDeviceRole BITS, scsiDevicePortNumber Unsigned32 } scsiDeviceIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is an arbitrary integer used to uniquely identify a particular device within a particular SCSI instance." ::= { scsiDeviceEntry 1 } scsiDeviceAlias OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..79)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains an administrative name for this device. If no name is assigned, the value of this object is the zero-length string. The StorageType of this object is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex." ::= { scsiDeviceEntry 2 } scsiDeviceRole OBJECT-TYPE Hallak-Stamler, et al. Standards Track [Page 28] RFC 4455 SCSI MIB April 2006 SYNTAX BITS { target(0), initiator(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object determines whether this device is acting as a SCSI initiator device, or as a SCSI target device, or as both." ::= { scsiDeviceEntry 3 } scsiDevicePortNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of ports contained in this device." ::= { scsiDeviceEntry 4 } – Port Table

scsiPortTable OBJECT-TYPE

    SYNTAX  SEQUENCE OF ScsiPortEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
      "A list of SCSI ports for each SCSI device in each instance."
 ::= { scsiGeneral 3 }
 scsiPortEntry OBJECT-TYPE
    SYNTAX            ScsiPortEntry
    MAX-ACCESS        not-accessible
    STATUS            current
    DESCRIPTION
      "An entry (row) containing management information applicable to
      a particular SCSI port of a particular SCSI device in a
      particular SCSI instance."
    INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex }
 ::= { scsiPortTable  1 }
 ScsiPortEntry ::= SEQUENCE {
    scsiPortIndex        ScsiIndexValue,
    scsiPortRole         BITS,
    scsiPortTransportPtr    RowPointer,
    scsiPortBusyStatuses Counter32
 }

Hallak-Stamler, et al. Standards Track [Page 29] RFC 4455 SCSI MIB April 2006

 scsiPortIndex OBJECT-TYPE
    SYNTAX      ScsiIndexValue
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "An arbitrary integer used to uniquely identify a particular
      port of a given device within a particular SCSI instance."
 ::= { scsiPortEntry 1 }
 scsiPortRole OBJECT-TYPE
    SYNTAX      BITS {
          target(0),
          initiator(1)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object indicates whether this port is acting as a
      SCSI initiator port, or as a SCSI target port or as both."
 ::= { scsiPortEntry 2 }
 scsiPortTransportPtr OBJECT-TYPE
    SYNTAX      RowPointer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object is a pointer to the corresponding row in the
      scsiTransportTable.  This row contains information on the
      transport such as transport type and port name."
 ::= { scsiPortEntry 3 }
 scsiPortBusyStatuses OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the number of port busy statuses sent or
      received by this port.  Note: Initiator ports only receive busy
      status and SCSI target ports only send busy status.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
 ::= { scsiPortEntry 4 }
  1. - Table of supported transports * scsiTransportTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiTransportEntry MAX-ACCESS not-accessible Hallak-Stamler, et al. Standards Track [Page 30] RFC 4455 SCSI MIB April 2006 STATUS current DESCRIPTION "This table contains the device transport-specific information for each transport connected to each device in scsiDeviceTable." ::= { scsiGeneral 5 } scsiTransportEntry OBJECT-TYPE SYNTAX ScsiTransportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing parameters applicable to a transport used by a particular device of a particular SCSI manageable instance." INDEX { scsiInstIndex, scsiDeviceIndex, scsiTransportIndex} ::= { scsiTransportTable 1 } ScsiTransportEntry ::= SEQUENCE { scsiTransportIndex ScsiIndexValue, scsiTransportType AutonomousType, scsiTransportPointer RowPointer, scsiTransportDevName ScsiName } scsiTransportIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular transport within a given device within a particular SCSI instance." ::= { scsiTransportEntry 1 } scsiTransportType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the transport type of this row of the transport table. For example, if this object has the value scsiTransportFCP, then the identified transport is FCP." ::= { scsiTransportEntry 2 } scsiTransportPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only Hallak-Stamler, et al. Standards Track [Page 31] RFC 4455 SCSI MIB April 2006 STATUS current DESCRIPTION "This object represents a pointer to a conceptual row in a 'transport' MIB module allowing a manager to get useful information for the transport described by this entry. For example, if the transport of this device is iSCSI, this object will point to the iSCSI Instance of the iSCSI MIB module. If there is no MIB for this transport, this object has the value 0.0." ::= { scsiTransportEntry 3 } scsiTransportDevName OBJECT-TYPE SYNTAX ScsiName MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of this device in one of the format(s) appropriate for this type of transport." ::= { scsiTransportEntry 4 } – SCSI Initiator Device Table *

scsiIntrDevTable OBJECT-TYPE

    SYNTAX           SEQUENCE OF ScsiIntrDevEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
      "This table contains information for each local SCSI initiator
      device in each instance."
 ::= { scsiInitiatorDevice 1}
 scsiIntrDevEntry OBJECT-TYPE
    SYNTAX           ScsiIntrDevEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
      "An entry (row) containing information applicable to a SCSI
      initiator device within a particular SCSI instance."
    INDEX { scsiInstIndex, scsiDeviceIndex }
 ::= { scsiIntrDevTable  1 }
 ScsiIntrDevEntry ::= SEQUENCE {
    scsiIntrDevTgtAccessMode   INTEGER,
    scsiIntrDevOutResets       Counter32
 }
 scsiIntrDevTgtAccessMode   OBJECT-TYPE
    SYNTAX      INTEGER {

Hallak-Stamler, et al. Standards Track [Page 32] RFC 4455 SCSI MIB April 2006

          unknown(1),
          autoEnable(2),
          manualEnable(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "This object controls whether or not a discovered SCSI target
      device is immediately authorized:
          - autoEnable (2) means that when a SCSI initiator device
          discovers a SCSI target device, it can use it immediately.
          - manualEnable (3) means that the SCSI initiator device
          must wait for an operator to set scsiIntrDscTgtConfigured
          = true before it is authorized.
      The StorageType of this object is specified by the instance
      of scsiInstStorageType that is INDEXed by the same value of
      scsiInstIndex."
 ::= { scsiIntrDevEntry 1 }
 scsiIntrDevOutResets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the total number of times that this SCSI
      initiator device has issued
      - a LOGICAL UNIT RESET or TARGET RESET task management request,
        or
      - any other SCSI transport protocol-specific action or event
        that causes a Logical Unit Reset or a Hard Reset at one or
        more SCSI target ports ([SAM2] chapters 5.9.6, 5.9.7).
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
    REFERENCE
       "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003,
       T10 Project 1157-D, 12 September 2002
       Chapters 5.9.6 & 5.9.7 [SAM2]"
 ::= { scsiIntrDevEntry 2 }
  1. - The following section describes managed objects related to
  2. - SCSI initiator ports.
 scsiIntrPortTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF ScsiIntrPortEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION

Hallak-Stamler, et al. Standards Track [Page 33] RFC 4455 SCSI MIB April 2006

      "This table contains all the SCSI initiator ports for each
      local SCSI initiator or target/initiator devices in each SCSI
      instance."
 ::= { scsiInitiatorDevice 2 }
 scsiIntrPortEntry OBJECT-TYPE
    SYNTAX          ScsiIntrPortEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
      "An entry (row) containing information applicable to a
      particular SCSI initiator port of a particular SCSI device
      within a SCSI instance."
    INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex }
 ::= { scsiIntrPortTable 1 }
 ScsiIntrPortEntry ::= SEQUENCE {
    scsiIntrPortName           ScsiName,
    scsiIntrPortIdentifier     ScsiIdentifier,
    scsiIntrPortOutCommands    Counter32,
    scsiIntrPortWrittenMegaBytes  Counter32,
    scsiIntrPortReadMegaBytes  Counter32,
    scsiIntrPortHSOutCommands  Counter64
 }
 scsiIntrPortName OBJECT-TYPE
    SYNTAX      ScsiName
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the name of the port assigned for use
      by the SCSI protocol.  The format will depend on the type of
      transport this port is using."
 ::= { scsiIntrPortEntry 1 }
 scsiIntrPortIdentifier OBJECT-TYPE
    SYNTAX      ScsiIdentifier
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the identifier of the port in one of
      the format(s) appropriate for the type of transport in use."
 ::= { scsiIntrPortEntry 2 }
 scsiIntrPortOutCommands OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "commands"

Hallak-Stamler, et al. Standards Track [Page 34] RFC 4455 SCSI MIB April 2006

    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the number of commands sent by this
      SCSI initiator port.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
 ::= { scsiIntrPortEntry 3 }
 scsiIntrPortWrittenMegaBytes  OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "Megabytes"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the amount of data in megabytes sent
      by this SCSI initiator port.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
 ::= { scsiIntrPortEntry 4 }
 scsiIntrPortReadMegaBytes  OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "Megabytes"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the amount of data in megabytes
      received by this SCSI initiator port.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
 ::= { scsiIntrPortEntry 5 }
 scsiIntrPortHSOutCommands  OBJECT-TYPE
    SYNTAX      Counter64
    UNITS       "commands"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the number of commands sent by this
      SCSI initiator port.  This object provides support for systems
      that can quickly generate a large number of commands because
      they run at high speed.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system."
 ::= { scsiIntrPortEntry 6 }

Hallak-Stamler, et al. Standards Track [Page 35] RFC 4455 SCSI MIB April 2006

  1. - Discovered SCSI Target Device group

scsiRemoteTgtDev OBJECT IDENTIFIER ::= { scsiInitiatorDevice 3 }

  1. - SCSI target device discovered or authorized to attach each of the
  2. - SCSI initiator ports of each SCSI initiator device of each
  3. - instance.
 scsiDscTgtTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF ScsiDscTgtEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "This table includes all the remote (not in the local system)
      SCSI target ports that are authorized to attach to each local
      SCSI initiator port of this SCSI instance."
 ::= { scsiRemoteTgtDev 1 }
 scsiDscTgtEntry OBJECT-TYPE
    SYNTAX         ScsiDscTgtEntry
    MAX-ACCESS     not-accessible
    STATUS         current
    DESCRIPTION
      "Each entry (row) contains information about the SCSI target
      device or port to which this SCSI initiator port (or all SCSI
      initiator ports in the SCSI initiator entry indexed by
      scsiInstIndex, scsiDeviceIndex) will attempt to attach.  The
      entry is either for all local ports (if scsiDscTgtIntrPortIndex
      is zero) or only for the specific SCSI initiator port
      identified by scsiDscTgtIntrPortIndex.  Note that if an entry in
      this table is deleted, any corresponding entries in the
      scsiDscLunsTable must be deleted as well.
      The StorageType of a row in this table is specified by the
      instance of scsiInstStorageType that is INDEXed by the same
      value of scsiInstIndex."
    INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex,
    scsiDscTgtIndex }
 ::= { scsiDscTgtTable 1 }
 ScsiDscTgtEntry ::= SEQUENCE {
    scsiDscTgtIntrPortIndex ScsiPortIndexValueOrZero,
    scsiDscTgtIndex         ScsiIndexValue,
    scsiDscTgtDevOrPort     ScsiDeviceOrPort,
    scsiDscTgtName          ScsiName,
    scsiDscTgtConfigured    TruthValue,
    scsiDscTgtDiscovered    TruthValue,
    scsiDscTgtInCommands    Counter32,
    scsiDscTgtWrittenMegaBytes Counter32,
    scsiDscTgtReadMegaBytes Counter32,

Hallak-Stamler, et al. Standards Track [Page 36] RFC 4455 SCSI MIB April 2006

    scsiDscTgtHSInCommands  Counter64,
    scsiDscTgtLastCreation  TimeStamp,
    scsiDscTgtRowStatus     RowStatus
 }
 scsiDscTgtIntrPortIndex OBJECT-TYPE
    SYNTAX      ScsiPortIndexValueOrZero
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "This object relates to a particular local device within a
      particular SCSI instance and specifies
      - the index of the local SCSI initiator port,
      - or zero, if this entry refers to the local device and
      therefore refers to all the local SCSI initiator ports."
 ::= { scsiDscTgtEntry 1 }
 scsiDscTgtIndex OBJECT-TYPE
    SYNTAX      ScsiIndexValue
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "This object is an arbitrary integer used to uniquely identify
      a particular SCSI target device either discovered by, or
      configured for use with, one or more ports scsiDscTgtName of
      a particular device within a particular SCSI instance."
 ::= { scsiDscTgtEntry 2 }
 scsiDscTgtDevOrPort OBJECT-TYPE
    SYNTAX      ScsiDeviceOrPort
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
      "This object indicates whether this entry describes a
      configured SCSI target device name (and applies to all ports
      on the identified SCSI target device) or an individual SCSI
      target port."
 ::= { scsiDscTgtEntry 3 }
 scsiDscTgtName OBJECT-TYPE
    SYNTAX      ScsiName
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
      "This object represents the name of this configured or
      discovered SCSI target device or port depending on the value
      of scsiDscTgtDevOrPort."
    ::= { scsiDscTgtEntry 4 }

Hallak-Stamler, et al. Standards Track [Page 37] RFC 4455 SCSI MIB April 2006

 scsiDscTgtConfigured OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
      "This object means
       -true(1): this entry has been configured by an administrator.
       -false(2): this entry has been added from a discovery
      mechanism (e.g., SendTargets, SLP, iSNS).
      An administrator can modify this value from false to true."
    DEFVAL { true }
 ::= { scsiDscTgtEntry 5 }
 scsiDscTgtDiscovered OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object means
       -true(1): this entry has been discovered by the SCSI instance
       as result of an automatic discovery process.
       -false(2):this entry has been added by manual configuration.
      This entry is read-only because an administrator cannot change
      it.
      Note that it is an implementation decision to determine how
      long to retain a row with configured=false, such as when the
      SCSI target device is no longer visible/accessible to the local
      SCSI initiator device."
 ::= { scsiDscTgtEntry 6 }
 scsiDscTgtInCommands OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "commands"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "This object represents the number of commands received from
       this SCSI target port or device.
       Discontinuities in the value of this counter can occur at re-
       initialization of the management system, and at other times as
       indicated by the value of scsiDscTgtLastCreation."
 ::= { scsiDscTgtEntry 7 }
 scsiDscTgtWrittenMegaBytes OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "Megabytes"
    MAX-ACCESS  read-only
    STATUS      current

Hallak-Stamler, et al. Standards Track [Page 38] RFC 4455 SCSI MIB April 2006

    DESCRIPTION
      "This object represents the amount of megabytes of data sent as
      the result of WRITE commands to this SCSI target port or device.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system, and at other times as
      indicated by the value of scsiDscTgtLastCreation."
 ::= { scsiDscTgtEntry 8 }
 scsiDscTgtReadMegaBytes OBJECT-TYPE
    SYNTAX      Counter32
    UNITS       "Megabytes"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the amount of megabytes received as the
      result of READ commands to this SCSI target port or device.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system, and at other times as
      indicated by the value of scsiDscTgtLastCreation."
 ::= { scsiDscTgtEntry 9 }
 scsiDscTgtHSInCommands OBJECT-TYPE
    SYNTAX      Counter64
    UNITS       "commands"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the number of commands received by this
      SCSI target port or device.  This object provides support for
      system that can quickly generate a large number of commands
      because they run at high speed.
      Discontinuities in the value of this counter can occur at re-
      initialization of the management system, and at other times as
      indicated by the value of scsiDscTgtLastCreation."
 ::= { scsiDscTgtEntry 10 }
 scsiDscTgtLastCreation OBJECT-TYPE
    SYNTAX      TimeStamp
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object represents the value of sysUpTime when this row
      was created."
 ::= { scsiDscTgtEntry 11 }
 scsiDscTgtRowStatus OBJECT-TYPE
    SYNTAX      RowStatus
    MAX-ACCESS  read-create

Hallak-Stamler, et al. Standards Track [Page 39] RFC 4455 SCSI MIB April 2006

    STATUS      current
    DESCRIPTION
      "This object allows an administrator to configure dynamically a
      new entry in this table via SNMP or eventually delete it.
      An administrator is not allowed to delete an entry for which
      the value of the object scsiIntrDscTgtDiscovered is equal to
      true.
      Note that when an entry in this table is deleted, then any
      corresponding entries in the scsiDscLunsTable must also be
      automatically deleted.
      A newly created row cannot be made active until a value has
      been set for scsiDscTgtName.  In this case, the value of the
      corresponding instance of the scsiDscTgtRowStatus column will
      stay 'notReady'.
      The RowStatus TC [RFC2579] requires that this DESCRIPTION
      clause states under which circumstances other objects in this
      row can be modified:
      The value of this object has no effect on whether other objects
      in this conceptual row can be modified."
 ::= { scsiDscTgtEntry 12 }
  1. - LUNs discovered *

scsiDscLunTable OBJECT-TYPE

    SYNTAX          SEQUENCE OF ScsiDscLunEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
      "This table includes all the remote (not in the local system)
      logical unit numbers (LUNs) discovered via each local SCSI
      initiator port of each local device within a particular SCSI
      instance."
 ::= { scsiRemoteTgtDev 2 }
 scsiDscLunEntry OBJECT-TYPE
    SYNTAX          ScsiDscLunEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
      "An entry (row) represents a discovered LUN at a particular
      SCSI target device (scsiDscTgtIndex), where the LUN was
      discovered by a particular local SCSI initiator device within a
      particular SCSI instance, possibly via a particular local
      SCSI initiator port.
      Note that when an entry in the scsiDscTgtTable is deleted,
      all corresponding entries in this table should automatically be
      deleted."

Hallak-Stamler, et al. Standards Track [Page 40] RFC 4455 SCSI MIB April 2006

    INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex,
    scsiDscTgtIndex, scsiDscLunIndex }
 ::= { scsiDscLunTable 1 }
 ScsiDscLunEntry ::= SEQUENCE {
    scsiDscLunIndex   ScsiIndexValue,
    scsiDscLunLun     ScsiLUN
 }
 scsiDscLunIndex OBJECT-TYPE
    SYNTAX      ScsiIndexValue
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "This object is an arbitrary integer used to uniquely identify
      a particular LUN discovered by a particular SCSI initiator port
      or a particular SCSI initiator device within a particular SCSI
      instance.
      Entries in the scsiDscLunIdTable are associated with a LUN by
      having the value of this object in their INDEX."
 ::= { scsiDscLunEntry 1 }
 scsiDscLunLun  OBJECT-TYPE
    SYNTAX      ScsiLUN
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This object contains the Logical Unit Number (LUN) of the
      discovered logical unit."
 ::= { scsiDscLunEntry 2 }
  1. - LU Identifiers discovered * scsiDscLunIdTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiDscLunIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes all the known LU identifiers of the remote (not in the local system) logical units discovered via each local SCSI initiator port or device of this SCSI instance." ::= { scsiRemoteTgtDev 3 } scsiDscLunIdEntry OBJECT-TYPE SYNTAX ScsiDscLunIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Hallak-Stamler, et al. Standards Track [Page 41] RFC 4455 SCSI MIB April 2006 "An entry (row) represents the LU identifier of a discovered LUN at a particular SCSI target device (scsiDscTgtIndex), where the LUN was discovered by a particular local SCSI initiator device within a particular SCSI instance, possibly via a particular local SCSI initiator port." INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex, scsiDscTgtIndex, scsiDscLunIndex, scsiDscLunIdIndex } ::= { scsiDscLunIdTable 1 } ScsiDscLunIdEntry ::= SEQUENCE { scsiDscLunIdIndex ScsiIndexValue, scsiDscLunIdCodeSet ScsiIdCodeSet, scsiDscLunIdAssociation ScsiIdAssociation, scsiDscLunIdType ScsiIdType, scsiDscLunIdValue ScsiIdValue } scsiDscLunIdIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is an arbitrary integer used to uniquely identify a particular LUN identifier discovered by each SCSI initiator device or particular SCSI initiator port within a particular SCSI instance." ::= { scsiDscLunIdEntry 1 } scsiDscLunIdCodeSet OBJECT-TYPE SYNTAX ScsiIdCodeSet MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the code set in use with this identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page." REFERENCE "ANSI - SCSI Primary Commands - 2 (SPC-2), ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4, Vital Product Data Parameters [SPC2]" ::= { scsiDscLunIdEntry 2 } scsiDscLunIdAssociation OBJECT-TYPE SYNTAX ScsiIdAssociation MAX-ACCESS read-only STATUS current DESCRIPTION Hallak-Stamler, et al. Standards Track [Page 42] RFC 4455 SCSI MIB April 2006 "This object specifies what the identifier is associated with (e.g., with the addressed physical/logical device or with a particular port). The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page." REFERENCE "ANSI - SCSI Primary Commands - 2 (SPC-2), ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4, Vital Product Data Parameters [SPC2]" ::= { scsiDscLunIdEntry 3 } scsiDscLunIdType OBJECT-TYPE SYNTAX ScsiIdType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the type of the identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page." REFERENCE "ANSI - SCSI Primary Commands - 2 (SPC-2), ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4, Vital Product Data Parameters [SPC2]" ::= { scsiDscLunIdEntry 4 } scsiDscLunIdValue OBJECT-TYPE SYNTAX ScsiIdValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the actual value of this identifier. The format is defined by the objects scsiDscLunIdCodeSet, scsiDscLunIdAssociation, scsiDscLunIdType. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page." REFERENCE "ANSI - SCSI Primary Commands - 2 (SPC-2), ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4, Vital Product Data Parameters [SPC2]" ::= { scsiDscLunIdEntry 5 } –* Table of SCSI Target Device Attached to local SCSI –* Initiator Ports scsiAttTgtPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiAttTgtPortEntry MAX-ACCESS not-accessible Hallak-Stamler, et al. Standards Track [Page 43] RFC 4455 SCSI MIB April 2006 STATUS current DESCRIPTION "This table includes all the remote (not in the local system) SCSI target ports that are currently attached to each local SCSI initiator port of this SCSI instance." ::= { scsiRemoteTgtDev 4 } scsiAttTgtPortEntry OBJECT-TYPE SYNTAX ScsiAttTgtPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) represents a remote SCSI target port (scsiAttTgtPortIndex) currently attached to a particular SCSI initiator port (scsiPortIndex) of a particular SCSI initiator device within a particular SCSI instance." INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex, scsiAttTgtPortIndex } ::= { scsiAttTgtPortTable 1 } ScsiAttTgtPortEntry ::= SEQUENCE { scsiAttTgtPortIndex ScsiIndexValue, scsiAttTgtPortDscTgtIdx ScsiIndexValueOrZero, scsiAttTgtPortName ScsiName, scsiAttTgtPortIdentifier ScsiIdentifier } scsiAttTgtPortIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular SCSI target currently attached to a particular SCSI initiator port of a particular SCSI initiator device within a particular SCSI instance." ::= { scsiAttTgtPortEntry 1 } scsiAttTgtPortDscTgtIdx OBJECT-TYPE SYNTAX ScsiIndexValueOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the scsiDscTgtIntrPortIndex index variable for the row in the scsiDscTgtTable representing this currently attached SCSI target port. If the currently attached SCSI target port is not represented in the scsiDscTgtTable, then the value of this object is zero." Hallak-Stamler, et al. Standards Track [Page 44] RFC 4455 SCSI MIB April 2006 ::= { scsiAttTgtPortEntry 2 } scsiAttTgtPortName OBJECT-TYPE SYNTAX ScsiName MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the attached SCSI target port." ::= { scsiAttTgtPortEntry 3 } scsiAttTgtPortIdentifier OBJECT-TYPE SYNTAX ScsiIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the identifier of the attached SCSI target port." ::= { scsiAttTgtPortEntry 4 } – * – * Table of SCSI Target devices – scsiTgtDevTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiTgtDevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about each local SCSI target device." ::= { scsiTargetDevice 1 } scsiTgtDevEntry OBJECT-TYPE SYNTAX ScsiTgtDevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing information applicable to a particular local SCSI target device within a particular SCSI instance." INDEX { scsiInstIndex, scsiDeviceIndex } ::= { scsiTgtDevTable 1 } ScsiTgtDevEntry ::= SEQUENCE { scsiTgtDevNumberOfLUs Gauge32, scsiTgtDeviceStatus INTEGER, scsiTgtDevNonAccessibleLUs Gauge32, scsiTgtDevResets Counter32 Hallak-Stamler, et al. Standards Track [Page 45] RFC 4455 SCSI MIB April 2006 } scsiTgtDevNumberOfLUs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the number of logical units accessible via this local SCSI target device." ::= { scsiTgtDevEntry 1 } scsiTgtDeviceStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), available(2), broken(3), readying(4), abnormal(5), nonAddrFailure(6), nonAddrFailReadying(7), nonAddrFailAbnormal(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the status of this SCSI device, summarizing the state of both the addressable devices (i.e., the logical units) and the non-addressable devices within this SCSI device: - unknown(1): This value is used when the status cannot be determined - available(2): All addressable and non-addressable devices within the SCSI device are fully operational (i.e., no logical units have an abnormal status). - broken(3): The SCSI device is not operational and cannot be made operational without external intervention. - readying(4): One or more logical units within the SCSI device are being initialized and access to the SCSI device is temporarily limited (i.e., one or more of the logical units have a readying status). - abnormal(5): One or more addressable devices within the SCSI device are indicating a status other than available; nevertheless, the SCSI device is operational (i.e., one or more of the logical units have an abnormal status). - nonAddrFailure(6): One or more non-addressable devices within the SCSI device have failed; nevertheless, the SCSI device is operational (i.e., no logical units have an abnormal or readying status). Hallak-Stamler, et al. Standards Track [Page 46] RFC 4455 SCSI MIB April 2006 - nonAddrFailReadying(7): One or more non-addressable devices within the SCSI device have failed; nevertheless, one or more logical units within the SCSI device are being initialized and access to the SCSI device is temporarily limited. - nonAddrFailAbnormal(8): One or more non-addressable devices within the SCSI device have failed and one or more addressable devices within the SCSI device are indicating a status other than available; however, the SCSI device is operational. " REFERENCE "SCSI Controller Commands-2 (SCC-2) ANSI INCITS 318-1998 6.3.1.8 REPORT STATES service action [SCC2]" ::= { scsiTgtDevEntry 2} scsiTgtDevNonAccessibleLUs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the number of logical units existing but not currently accessible via this local SCSI target device." ::= { scsiTgtDevEntry 3 } scsiTgtDevResets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of hard resets encountered by this SCSI target device. Discontinuities in the value of this counter can occur at re- initialization of the management system." REFERENCE "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003, T10 Project 1157-D, 12 September 2002 - Chapter 5.9.7 [SAM2]" ::= { scsiTgtDevEntry 4 } – SCSI Target Port Table * scsiTgtPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiTgtPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes all the local SCSI target ports of all the local SCSI target devices." Hallak-Stamler, et al. Standards Track [Page 47] RFC 4455 SCSI MIB April 2006 ::= { scsiTargetDevice 2 } scsiTgtPortEntry OBJECT-TYPE SYNTAX ScsiTgtPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing information applicable to a particular local SCSI target port of a particular local SCSI target device within a particular SCSI instance." INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex} ::= { scsiTgtPortTable 1 } ScsiTgtPortEntry ::= SEQUENCE { scsiTgtPortName ScsiName, scsiTgtPortIdentifier ScsiIdentifier, scsiTgtPortInCommands Counter32, scsiTgtPortWrittenMegaBytes Counter32, scsiTgtPortReadMegaBytes Counter32, scsiTgtPortHSInCommands Counter64 } scsiTgtPortName OBJECT-TYPE SYNTAX ScsiName MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the port assigned for use in the SCSI protocol." ::= { scsiTgtPortEntry 1 } scsiTgtPortIdentifier OBJECT-TYPE SYNTAX ScsiIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the identifier of the port in one of the format(s) appropriate for the type of transport." ::= { scsiTgtPortEntry 2 } scsiTgtPortInCommands OBJECT-TYPE SYNTAX Counter32 UNITS "commands" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of commands received by this SCSI target port. Hallak-Stamler, et al. Standards Track [Page 48] RFC 4455 SCSI MIB April 2006 Discontinuities in the value of this counter can occur at re- initialization of the management system." ::= { scsiTgtPortEntry 3 } scsiTgtPortWrittenMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the amount of data written in megabytes by this SCSI target port. Discontinuities in the value of this counter can occur at re- initialization of the management system." ::= { scsiTgtPortEntry 4 } scsiTgtPortReadMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the amount of data read in megabytes by this SCSI target port. Discontinuities in the value of this counter can occur at re- initialization of the management system." ::= { scsiTgtPortEntry 5 } scsiTgtPortHSInCommands OBJECT-TYPE SYNTAX Counter64 UNITS "commands" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of commands received. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system." ::= { scsiTgtPortEntry 6 } scsiRemoteIntrDev OBJECT IDENTIFIER ::= { scsiTargetDevice 3 } – The scsiAuthorizedIntrTable contains the list of remote initiator – ports that are authorized to be attached to specific SCSI target – ports and on which an administrator would like to keep permanent – information and long term statistics even when not currently – attached. Hallak-Stamler, et al. Standards Track [Page 49] RFC 4455 SCSI MIB April 2006 scsiAuthorizedIntrTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiAuthorizedIntrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes all the authorized SCSI initiator devices or ports that may attach a SCSI target device (ScsiAuthIntrTgtPortIndex = 0) or port (ScsiAuthIntrTgtPortIndex different than 0) of the local SCSI instance. Statistics are kept for each such authorization; thus, the authorizations should be configured in the manner that will cause the desired set of statistics to be collected and that will determine the correct LUN map." ::= { scsiRemoteIntrDev 1 } scsiAuthorizedIntrEntry OBJECT-TYPE SYNTAX ScsiAuthorizedIntrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) represents a remote SCSI initiator port or remote SCSI initiator device that may attach to the local SCSI target port or device within a particular SCSI instance. The StorageType of a row in this table is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex." INDEX { scsiInstIndex, scsiDeviceIndex, scsiAuthIntrTgtPortIndex, scsiAuthIntrIndex } ::= { scsiAuthorizedIntrTable 1 } ScsiAuthorizedIntrEntry ::= SEQUENCE { scsiAuthIntrTgtPortIndex ScsiPortIndexValueOrZero, scsiAuthIntrIndex ScsiIndexValue, scsiAuthIntrDevOrPort ScsiDeviceOrPort, scsiAuthIntrName ScsiName, scsiAuthIntrLunMapIndex ScsiIndexValueOrZero, scsiAuthIntrAttachedTimes Counter32, scsiAuthIntrOutCommands Counter32, scsiAuthIntrReadMegaBytes Counter32, scsiAuthIntrWrittenMegaBytes Counter32, scsiAuthIntrHSOutCommands Counter64, scsiAuthIntrLastCreation TimeStamp, scsiAuthIntrRowStatus RowStatus } scsiAuthIntrTgtPortIndex OBJECT-TYPE SYNTAX ScsiPortIndexValueOrZero Hallak-Stamler, et al. Standards Track [Page 50] RFC 4455 SCSI MIB April 2006 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains either the index of the port or zero, to indicate any port, on the particular local SCSI target device." ::= { scsiAuthorizedIntrEntry 1 } scsiAuthIntrIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is an arbitrary integer used to uniquely identify a SCSI initiator device or port that is authorized to attach to a particular local SCSI target device or port of a particular SCSI instance." ::= { scsiAuthorizedIntrEntry 2 } scsiAuthIntrDevOrPort OBJECT-TYPE SYNTAX ScsiDeviceOrPort MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether this entry refers to a remote SCSI initiator port or to a SCSI initiator device. A value of device(1) means that the authorized remote initiator is a SCSI initiator device and includes all of its ports. A value of port(2) means that the authorized remote initiator is a SCSI initiator port." ::= { scsiAuthorizedIntrEntry 3 } scsiAuthIntrName OBJECT-TYPE SYNTAX ScsiName MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the name of the remote SCSI initiator device or port authorized by this row." ::= { scsiAuthorizedIntrEntry 4 } scsiAuthIntrLunMapIndex OBJECT-TYPE SYNTAX ScsiIndexValueOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the set of entries in the scsiLunMapTable for which scsiLunMapIndex has the same value as the value of this object. The identified set of entries Hallak-Stamler, et al. Standards Track [Page 51] RFC 4455 SCSI MIB April 2006 constitutes the LUN map to be used for accessing logical units when the remote SCSI initiator port or device corresponding to this entry is attached to any local SCSI target port or device corresponding to this entry. Note that this object has a value of zero if this entry should use the default LUN map." ::= { scsiAuthorizedIntrEntry 5 } scsiAuthIntrAttachedTimes OBJECT-TYPE SYNTAX Counter32 UNITS "Times" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of times that this remote SCSI initiator device or port has transitioned from unattached to attached to this local SCSI target device or port. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation." ::= { scsiAuthorizedIntrEntry 6 } scsiAuthIntrOutCommands OBJECT-TYPE SYNTAX Counter32 UNITS "commands" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of commands that the remote SCSI initiator device or port corresponding to this entry has sent to the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation." ::= { scsiAuthorizedIntrEntry 7 } scsiAuthIntrReadMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the amount of data in megabytes that the remote SCSI initiator device or port corresponding to this entry has read from the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- Hallak-Stamler, et al. Standards Track [Page 52] RFC 4455 SCSI MIB April 2006 initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation." ::= { scsiAuthorizedIntrEntry 8 } scsiAuthIntrWrittenMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the amount of data in megabytes that the remote SCSI initiator device or port corresponding to this entry has written to the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation." ::= { scsiAuthorizedIntrEntry 9} scsiAuthIntrHSOutCommands OBJECT-TYPE SYNTAX Counter64 UNITS "commands" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of commands sent by the remote SCSI initiator device or port corresponding to this entry to the local SCSI target device or port corresponding to this entry. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation." ::= { scsiAuthorizedIntrEntry 10 } scsiAuthIntrLastCreation OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of sysUpTime when this row was last created." ::= { scsiAuthorizedIntrEntry 11 } scsiAuthIntrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create Hallak-Stamler, et al. Standards Track [Page 53] RFC 4455 SCSI MIB April 2006 STATUS current DESCRIPTION "This object allows an administrator to create or delete this entry. A newly created row cannot be made active until a value has been set for scsiAuthIntrName. In this case, the value of the corresponding instance of the scsiAuthIntrRowStatus column will stay 'notReady'. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { scsiAuthorizedIntrEntry 12 } – Table of SCSI initiator devices or ports attached to local – SCSI target ports – scsiAttIntrPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiAttIntrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes all the remote SCSI initiator ports that are currently attached to a local SCSI target port of all local devices within all SCSI instances." ::= { scsiRemoteIntrDev 2 } scsiAttIntrPortEntry OBJECT-TYPE SYNTAX ScsiAttIntrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) represents a remote SCSI initiator port currently attached to a particular local SCSI target port of a particular SCSI target device of a particular SCSI instance." INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex, scsiAttIntrPortIndex } ::= { scsiAttIntrPortTable 1 } ScsiAttIntrPortEntry ::= SEQUENCE { scsiAttIntrPortIndex ScsiIndexValue, scsiAttIntrPortAuthIntrIdx ScsiIndexValueOrZero, scsiAttIntrPortName ScsiName, scsiAttIntrPortIdentifier ScsiIdentifier } Hallak-Stamler, et al. Standards Track [Page 54] RFC 4455 SCSI MIB April 2006 scsiAttIntrPortIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary integer used to uniquely identify a particular attached remote initiator port to a particular SCSI target port within a particular SCSI target device within a particular SCSI instance." ::= { scsiAttIntrPortEntry 1 } scsiAttIntrPortAuthIntrIdx OBJECT-TYPE SYNTAX ScsiIndexValueOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the corresponding index in the scsiAuthorizedIntrTable for this current attached remote SCSI initiator device or zero if this remote attached SCSI initiator device is not configured in that table." ::= { scsiAttIntrPortEntry 2 } scsiAttIntrPortName OBJECT-TYPE SYNTAX ScsiName MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the remote SCSI initiator device attached to this local SCSI target port." ::= { scsiAttIntrPortEntry 3 } scsiAttIntrPortIdentifier OBJECT-TYPE SYNTAX ScsiIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the identifier of the remote SCSI initiator device attached to this local SCSI target port." ::= { scsiAttIntrPortEntry 4 } – Managed Objects regarding logical units * scsiLuTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiLuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the logical units exposed by local SCSI target devices. Hallak-Stamler, et al. Standards Track [Page 55] RFC 4455 SCSI MIB April 2006 It includes attributes for the World Wide Name (WWN), scsiLuVendorId, scsiLuProductId, and scsiLuRevisionId, which may also appear in the scsiLuIdTable. If an implementation exposes a WWN as a LuIdTable entry, it must match the scsiLuWwnName in this table. If an implementation exposes a (vendor, product, revision) identifier as an LuIdTable entry, each of these fields must match the scsiLuVendorId, scsiLuProductId, and scsiLuRevisionId attributes in this table." ::= { scsiLogicalUnit 1 } scsiLuEntry OBJECT-TYPE SYNTAX ScsiLuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) contains information applicable to a particular logical unit of a particular local SCSI target device within a particular SCSI instance." INDEX { scsiInstIndex, scsiDeviceIndex, scsiLuIndex} ::= { scsiLuTable 1 } ScsiLuEntry ::= SEQUENCE { scsiLuIndex ScsiIndexValue, scsiLuDefaultLun ScsiLUN, scsiLuWwnName ScsiLuNameOrZero, scsiLuVendorId SnmpAdminString, scsiLuProductId SnmpAdminString, scsiLuRevisionId SnmpAdminString, scsiLuPeripheralType Unsigned32, scsiLuStatus INTEGER, scsiLuState BITS, scsiLuInCommands Counter32, scsiLuReadMegaBytes Counter32, scsiLuWrittenMegaBytes Counter32, scsiLuInResets Counter32, scsiLuOutTaskSetFullStatus Counter32, scsiLuHSInCommands Counter64, scsiLuLastCreation TimeStamp } scsiLuIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary integer used to uniquely identify a particular logical unit within a particular SCSI target device within a particular SCSI instance." Hallak-Stamler, et al. Standards Track [Page 56] RFC 4455 SCSI MIB April 2006 ::= { scsiLuEntry 1 } scsiLuDefaultLun OBJECT-TYPE SYNTAX ScsiLUN MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the default Logical Unit Number (LUN) for this logical unit; if a SCSI initiator device has not been configured to view this logical unit via an entry in the ScsiLunMapTable, the LU will be visible as scsiLuDefaultLun. If this logical unit does not have a default LUN, it will only be visible if specified via the ScsiLunMapTable, and this object will contain a zero-length string." ::= { scsiLuEntry 2 } scsiLuWwnName OBJECT-TYPE SYNTAX ScsiLuNameOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the World Wide Name of this LU that is the device identifier of the Vital Product Data (VPD) page name; if there is no WWN for this LU, this object will contain a zero-length string. If there is more than one identifier, they will be listed in the scsiLuIdTable and this object will contain a zero-length string." ::= { scsiLuEntry 3 } scsiLuVendorId OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents a string identifying the vendor of this LU as reported in the Standard INQUIRY data." ::= { scsiLuEntry 4 } scsiLuProductId OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents a string identifying the product for this LU as reported in the Standard INQUIRY data." ::= { scsiLuEntry 5 } scsiLuRevisionId OBJECT-TYPE Hallak-Stamler, et al. Standards Track [Page 57] RFC 4455 SCSI MIB April 2006 SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents a string defining the product revision of this LU as reported in the Standard INQUIRY data." ::= { scsiLuEntry 6 } scsiLuPeripheralType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the value returned by SCSI Standard INQUIRY data. It can be: direct-access device, sequential-access device, printer, communication device and so on. The values that can be returned here are defined in SCSI Primary Commands -2." REFERENCE "ANSI - SCSI Primary Commands - 2 (SPC-2), ANSI INCITS 351-2001,11 July 2001 [SPC2]- Table 48." ::= { scsiLuEntry 7 } scsiLuStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), available(2), notAvailable(3), broken(4), readying(5), abnormal(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the status of this logical unit: - unknown(1): The status of this logical unit cannot be determined. - available(2): The logical unit is fully operational (i.e., accepts media access SCSI commands and has no state information to report). - notAvailable(3): The logical unit is capable of being supported but is not available (i.e., no logical unit is currently present or the logical unit is present but not configured for use). - broken(4): The logical unit has failed and cannot respond to SCSI commands. - readying(5): The logical unit is being initialized and Hallak-Stamler, et al. Standards Track [Page 58] RFC 4455 SCSI MIB April 2006 access is temporarily limited. - abnormal(6): The logical unit has state information available that indicates it is operating with limits. The scsiLuState indicates what those limits are. " REFERENCE "SCSI Controller Commands-2 (SCC-2) ANSI INCITS 318-1998 6.3.1.8 REPORT STATES service action [SCC2]" ::= { scsiLuEntry 8 } scsiLuState OBJECT-TYPE SYNTAX BITS { dataLost(0), dynamicReconfigurationInProgress(1), exposed(2), fractionallyExposed(3), partiallyExposed(4), protectedRebuild(5), protectionDisabled(6), rebuild(7), recalculate(8), spareInUse(9), verifyInProgress(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the state of a logical unit and its meaning according to the bit position: 0 Data lost: Within the logical unit data has been lost. 1 Dynamic reconfiguration in progress: The logical unit is being reconfigured. In this state all data is still protected. 2 Exposed: Within the logical unit data is not protected. In this state all data is still valid; however, loss of data or data availability is unavoidable in the event of a failure. 3 Fractionally exposed: Within the logical unit part of the data is not protected. In this state all data is still valid; however, a failure may cause a loss of data or a loss of data availability. 4 Partially exposed: Within the logical unit one or more underlying storage devices have failed. In this state all data is still protected. 5 Protected rebuild: The logical unit is in the process of a rebuild operation. In this state all data is protected. 6 Protection disabled: Within the logical unit the data Hallak-Stamler, et al. Standards Track [Page 59] RFC 4455 SCSI MIB April 2006 protection method has been disabled. In this state all data is still valid; however, loss of data or data availability is unavoidable in the event of a failure. 7 Rebuild: The data protection method is in the process of rebuilding data. In this state data is not protected. 8 Recalculate: The logical unit is in the process of a recalculate operation. 9 Spare in use: Within the logical unit a storage device in full or part is being used to store data. In this state all data is still protected. 10 Verify in progress: Within the logical unit data is being verified." REFERENCE "SCSI Controller Commands-2 (SCC-2) ANSI INCITS 318-1998 6.3.1.8 REPORT STATES service action [SCC2]" ::= { scsiLuEntry 9 } scsiLuInCommands OBJECT-TYPE SYNTAX Counter32 UNITS "commands" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of commands received by this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." ::= { scsiLuEntry 10 } scsiLuReadMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the amount of data in megabytes read from this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." ::= { scsiLuEntry 11 } scsiLuWrittenMegaBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Megabytes" MAX-ACCESS read-only Hallak-Stamler, et al. Standards Track [Page 60] RFC 4455 SCSI MIB April 2006 STATUS current DESCRIPTION "This object represents the amount of data in megabytes written to this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." ::= { scsiLuEntry 12 } scsiLuInResets OBJECT-TYPE SYNTAX Counter32 UNITS "resets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of times that this logical unit received - a LOGICAL UNIT RESET or TARGET RESET task management request, or - any other SCSI transport protocol-specific action or event that causes a Logical Unit Reset or a Hard Reset at a SCSI target port of the containing device ([SAM2] Chapters 5.9.6, 5.9.7). Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." REFERENCE "SCSI Architecture Model-2 (SAM-2), ANSI INCITS 366-2003, T10 Project 1157-D, 12 September 2002 - Chapter 5.9.7 [SAM2]" ::= { scsiLuEntry 13 } scsiLuOutTaskSetFullStatus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of Task Set full statuses issued for this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." ::= { scsiLuEntry 14 } scsiLuHSInCommands OBJECT-TYPE SYNTAX Counter64 UNITS "commands" MAX-ACCESS read-only STATUS current Hallak-Stamler, et al. Standards Track [Page 61] RFC 4455 SCSI MIB April 2006 DESCRIPTION "This object represents the number of commands received by this logical unit. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation." ::= { scsiLuEntry 15 } scsiLuLastCreation OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of sysUpTime when this row was last created." ::= { scsiLuEntry 16 } – Logical Unit Identifier Table *

scsiLuIdTable OBJECT-TYPE

    SYNTAX  SEQUENCE OF ScsiLuIdEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
       "A table of identifiers for all logical units exposed by the
       local SCSI target device."
 ::= { scsiLogicalUnit 2 }
 scsiLuIdEntry OBJECT-TYPE
    SYNTAX      ScsiLuIdEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "An entry (row) containing information applicable to a
      particular identifier for a particular logical unit of a
      particular SCSI target device within a particular SCSI
      instance."
    INDEX {scsiInstIndex, scsiDeviceIndex, scsiLuIndex, scsiLuIdIndex}
 ::= { scsiLuIdTable 1 }
 ScsiLuIdEntry ::= SEQUENCE {
    scsiLuIdIndex        ScsiIndexValue,
    scsiLuIdCodeSet      ScsiIdCodeSet,
    scsiLuIdAssociation  ScsiIdAssociation,
    scsiLuIdType         ScsiIdType,
    scsiLuIdValue        ScsiIdValue
 }

Hallak-Stamler, et al. Standards Track [Page 62] RFC 4455 SCSI MIB April 2006

 scsiLuIdIndex  OBJECT-TYPE
    SYNTAX          ScsiIndexValue
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
      "This object represents an arbitrary integer used to uniquely
      identify a particular LU identifier within a particular logical
      unit within a particular SCSI target device within a particular
      SCSI instance."
 ::= { scsiLuIdEntry 1 }
 scsiLuIdCodeSet OBJECT-TYPE
    SYNTAX           ScsiIdCodeSet
    MAX-ACCESS       read-only
    STATUS           current
    DESCRIPTION
      "This object specifies the code set in use with this
      identifier.  The value is represented in the same format as is
      contained in the identifier's Identification Descriptor within
      the logical unit's Device Identification Page."
    REFERENCE
      "ANSI - SCSI Primary Commands - 2 (SPC-2),
      ANSI INCITS 351-2001, 11 July 2001 Chapter 8: section 8.4.4,
      Vital Product Data Parameters [SPC2]"
 ::= { scsiLuIdEntry 2 }
 scsiLuIdAssociation OBJECT-TYPE
    SYNTAX           ScsiIdAssociation
    MAX-ACCESS       read-only
    STATUS           current
    DESCRIPTION
      "This object specifies what the identifier is associated with
      (e.g., with the addressed physical/logical device or with a
      particular port).  The value is represented in the same format
      as is contained in the identifier's Identification Descriptor
      within the logical unit's Device Identification Page."
    REFERENCE
      "ANSI - SCSI Primary Commands - 2 (SPC-2),
      ANSI INCITS 351-2001, 11 July 2001, Chapter 8: section 8.4.4,
      Vital Product Data Parameters [SPC2]"
 ::= { scsiLuIdEntry 3 }
 scsiLuIdType   OBJECT-TYPE
    SYNTAX           ScsiIdType
    MAX-ACCESS       read-only
    STATUS           current
    DESCRIPTION
      "This object specifies the type of the identifier.

Hallak-Stamler, et al. Standards Track [Page 63] RFC 4455 SCSI MIB April 2006

      The value is represented in the same format as is contained in
      the identifier's Identification Descriptor within the logical
      unit's Device Identification Page."
    REFERENCE
      "ANSI - SCSI Primary Commands - 2 (SPC-2),
      ANSI INCITS 351-2001, 11 July 2001, Chapter 8: section 8.4.4,
      Vital Product Data Parameters [SPC2]"
 ::= { scsiLuIdEntry 4 }
 scsiLuIdValue OBJECT-TYPE
    SYNTAX         ScsiIdValue
    MAX-ACCESS     read-only
    STATUS         current
    DESCRIPTION
      "This object represents the actual value of this identifier.
      The format is defined by the objects scsiLuIdCodeSet,
      scsiLuIdAssociation, scsiLuIdType.
      The value is represented in the same format as is contained in
      the identifier's Identification Descriptor within the logical
      unit's Device Identification Page."
    REFERENCE
      "ANSI - SCSI Primary Commands - 2 (SPC-2),
      ANSI INCITS 351-2001, 11 July 2001, Chapter 8: section 8.4.4,
      Vital Product Data Parameters [SPC2]"
 ::= { scsiLuIdEntry 5 }
  1. -* The LUN Map Table scsiLunMapTable OBJECT-TYPE SYNTAX SEQUENCE OF ScsiLunMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the ability to present a logical unit using different Logical Unit Numbers for different SCSI initiator devices. This table provides a mapping between a logical unit and a Logical Unit Number, and can be referenced by a ScsiAuthorizedIntrEntry to specify the LUN map for that initiator." ::= { scsiLogicalUnit 3 } scsiLunMapEntry OBJECT-TYPE SYNTAX ScsiLunMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about the mapping of a Hallak-Stamler, et al. Standards Track [Page 64] RFC 4455 SCSI MIB April 2006 particular logical unit to a particular LUN. The set of entries that all have the same values of scsiInstIndex, scsiDeviceIndex and scsiLunMapIndex constitutes a LUN map within a particular SCSI instance. The StorageType of a row in this table is specified by the instance of scsiInstStorageType that is INDEX-ed by the same value of scsiInstIndex." INDEX { scsiInstIndex, scsiDeviceIndex, scsiLunMapIndex, scsiLunMapLun} ::= { scsiLunMapTable 1 } ScsiLunMapEntry ::= SEQUENCE { scsiLunMapIndex ScsiIndexValue, scsiLunMapLun ScsiLUN, scsiLunMapLuIndex ScsiIndexValue, scsiLunMapRowStatus RowStatus } scsiLunMapIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary integer used to uniquely identify a particular LunMap within a particular SCSI target device within a particular SCSI instance." ::= { scsiLunMapEntry 1 } scsiLunMapLun OBJECT-TYPE SYNTAX ScsiLUN MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Logical Unit Number, to which a logical unit is mapped by this row." ::= { scsiLunMapEntry 2 } scsiLunMapLuIndex OBJECT-TYPE SYNTAX ScsiIndexValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the logical unit for which the value of scsiLuIndex is the same as the value of this object. The identified logical unit is the one mapped to a LUN by this row." ::= { scsiLunMapEntry 3 } Hallak-Stamler, et al. Standards Track [Page 65] RFC 4455 SCSI MIB April 2006 scsiLunMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows an administrator to create and delete this entry." ::= { scsiLunMapEntry 4 } – Notifications – scsiNotifications OBJECT IDENTIFIER ::= { scsiMIB 2 } scsiNotificationsPrefix OBJECT IDENTIFIER ::= { scsiNotifications 0 } scsiTgtDeviceStatusChanged NOTIFICATION-TYPE OBJECTS { scsiTgtDeviceStatus } STATUS current DESCRIPTION "This notification will be generated for each occurrence of the abnormal status (e.g., if the SCSI target device's current status is abnormal) providing that the SCSI instance's value of scsiInstScsiNotificationsEnable is enabled. An SNMP agent implementing the SCSI MIB module should not send more than three SCSI identical notifications in any 10-second period." ::= { scsiNotificationsPrefix 1 } scsiLuStatusChanged NOTIFICATION-TYPE OBJECTS { scsiLuStatus } STATUS current DESCRIPTION "This notification will be generated each time that scsiLuStatus changes providing that the SCSI instance's value of scsiInstScsiNotificationsEnable is enabled. An SNMP agent implementing the SCSI MIB module should not send more than three SCSI identical notifications in any 10-second period." ::= { scsiNotificationsPrefix 2 } –
  2. - The next part defines the conformance groups in use
  3. - for SCSI MIB module.

scsiCompliances OBJECT IDENTIFIER ::= { scsiConformance 1 }

 scsiCompliance MODULE-COMPLIANCE

Hallak-Stamler, et al. Standards Track [Page 66] RFC 4455 SCSI MIB April 2006

    STATUS current
    DESCRIPTION
      "Describes the requirements for compliance to this SCSI MIB
       module.
      If an implementation can be both a SCSI target device and a SCSI
      initiator device, all groups are mandatory."
    MODULE  -- this module
       MANDATORY-GROUPS {
          scsiDeviceGroup
      }
      OBJECT scsiInstAlias
      MIN-ACCESS read-only
      DESCRIPTION
         "Write access is not mandatory."
      OBJECT scsiInstScsiNotificationsEnable
      MIN-ACCESS read-only
      DESCRIPTION
         "Write access is not mandatory."
      OBJECT scsiDeviceAlias
      MIN-ACCESS read-only
      DESCRIPTION
         "Write access is not mandatory."
      OBJECT scsiInstStorageType
      MIN-ACCESS   read-only
      DESCRIPTION
         "Write access is not required."
  1. - Conditionally mandatory groups to be included with
  2. - the mandatory groups when the implementation has
  3. - SCSI target device.
      GROUP scsiTargetDeviceGroup
      DESCRIPTION
         "This group is mandatory for all SCSI implementations that
         have SCSI target devices."
      GROUP scsiLunMapGroup
      DESCRIPTION
        "This group is mandatory for systems having the capabilities
         of mapping local SCSI target devices and logical units
         according to remote SCSI initiator devices."
      OBJECT scsiAuthIntrDevOrPort
      MIN-ACCESS   read-only
      DESCRIPTION

Hallak-Stamler, et al. Standards Track [Page 67] RFC 4455 SCSI MIB April 2006

       "Write access is not required."
      OBJECT scsiAuthIntrName
      MIN-ACCESS   read-only
      DESCRIPTION
       "Write access is not required."
      OBJECT scsiAuthIntrLunMapIndex
      MIN-ACCESS   read-only
      DESCRIPTION
       "Write access is not required."
      OBJECT scsiAuthIntrRowStatus
      SYNTAX RowStatus { active(1) }
      MIN-ACCESS   read-only
      DESCRIPTION
        "Write access is not required, and only one of the six
        enumerated values for the RowStatus textual convention need
        be supported, specifically: active(1)."
      GROUP scsiTgtDevLuNotificationsGroup
      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        have SCSI target devices and are able to report status
        changes."
  1. - Conditionally mandatory groups to be included with
  2. - the mandatory groups when the implementation has
  3. - SCSI initiator device.
      GROUP scsiInitiatorDeviceGroup
      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        have SCSI initiator devices."
       OBJECT scsiIntrDevTgtAccessMode
       MIN-ACCESS read-only
       DESCRIPTION "Write access is not mandatory."
       GROUP scsiDiscoveryGroup
       DESCRIPTION
         "This group is mandatory for systems having the capabilities
         of discovering remote SCSI target devices via local SCSI
         initiator devices."
       OBJECT scsiLunMapLuIndex
       MIN-ACCESS read-only

Hallak-Stamler, et al. Standards Track [Page 68] RFC 4455 SCSI MIB April 2006

       DESCRIPTION
         "Write access is not mandatory."
       OBJECT scsiLunMapRowStatus
       SYNTAX RowStatus { active(1) }
       MIN-ACCESS read-only
       DESCRIPTION
         "Write access is not required, and only one of the six
         enumerated values for the RowStatus textual convention need
         be supported, specifically: active(1)."
       OBJECT scsiDscTgtDevOrPort
       MIN-ACCESS read-only
       DESCRIPTION
         "Write access is not mandatory."
       OBJECT scsiDscTgtName
       MIN-ACCESS read-only
       DESCRIPTION "Write access is not mandatory."
       OBJECT scsiDscTgtConfigured
       SYNTAX TruthValue { false(2) }
       MIN-ACCESS read-only
       DESCRIPTION
         "The value of true(1) is not mandatory neither is the write
         access."
       OBJECT scsiDscTgtRowStatus
       SYNTAX RowStatus { active(1) }
       MIN-ACCESS read-only
       DESCRIPTION
         "Write access is not required, and only one of the six
         enumerated values for the RowStatus textual convention need
         be supported, specifically: active(1)."
  1. - Conditionally mandatory groups to be included with the mandatory
  2. - groups when the implementation can gather statistics.
      GROUP scsiDeviceStatGroup
      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        can gather statistics."
  1. - Conditionally mandatory groups to be included with the mandatory
  2. - groups when the implementation can gather statistics at the SCSI
  3. - initiator device side.
      GROUP scsiInitiatorDevStatsGroup

Hallak-Stamler, et al. Standards Track [Page 69] RFC 4455 SCSI MIB April 2006

      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        can gather statistics at SCSI initiator device side."
      GROUP scsiDiscoveryStatsGroup
      DESCRIPTION
        "This group is mandatory for system having the capabilities
        of gathering statistics regarding remote SCSI target devices
        via local SCSI initiator devices."
  1. - Conditionally mandatory groups to be included with the mandatory
  2. - groups when the implementation can gather statistics at the SCSI
  3. - target side.
      GROUP scsiTargetDevStatsGroup
      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        can gather statistics at SCSI target devices."
      GROUP scsiLunMapStatsGroup
      DESCRIPTION
        "This group is mandatory for SCSI implementations able to map
        local SCSI target devices and logical units according to
        remote SCSI initiator devices."
  1. - Conditionally mandatory groups to be included with the mandatory
  2. - groups when the implementation is running at high speed and can
  3. - gather statistics at the SCSI initiator device side.
      GROUP scsiInitiatorDevHSStatsGroup
      DESCRIPTION
        "This group is mandatory for all SCSI implementations that
        can gather statistics at the SCSI initiator device side and
        are running at high speed, meaning speed of 4 Gbit/second or
        higher."
      GROUP scsiDiscoveryHSStatsGroup
      DESCRIPTION
        "This group is mandatory for systems having the capabilities
        of gathering statistics regarding remote SCSI target devices
        via local SCSI initiator devices and are running at high
        speed, meaning speed of 4 Gbit/second or higher."
  1. - Conditionally mandatory groups to be included with the mandatory
  2. - groups when the implementation is running at high speed and can
  3. - gather statistics at the SCSI target side.

GROUP scsiTargetDevHSStatsGroup

      DESCRIPTION

Hallak-Stamler, et al. Standards Track [Page 70] RFC 4455 SCSI MIB April 2006

        "This group is mandatory for all SCSI implementations that
        can gather statistics at SCSI target devices in high speed
        systems, meaning speed of 4 Gbit/second or higher."
      GROUP scsiLunMapHSStatsGroup
      DESCRIPTION
        "This group is mandatory for SCSI implementations able to map
        local SCSI target devices and logical units according to
        remote SCSI initiator devices in a high speed system, meaning
        speed of 4 Gbit/second or higher."
 ::= { scsiCompliances 1 }
 scsiGroups OBJECT IDENTIFIER ::= { scsiConformance 2 }
 scsiDeviceGroup OBJECT-GROUP
    OBJECTS {
       scsiInstAlias,
       scsiInstSoftwareIndex,
       scsiInstVendorVersion,
       scsiInstScsiNotificationsEnable,
       scsiInstStorageType,
       scsiDeviceAlias,
       scsiDeviceRole,
       scsiDevicePortNumber,
       scsiPortRole,
       scsiPortTransportPtr,
       scsiTransportType,
       scsiTransportPointer,
       scsiTransportDevName
    }
    STATUS current
    DESCRIPTION
      "A collection of objects providing information about SCSI
      instances, devices, and ports."
 ::= { scsiGroups 1 }
 scsiInitiatorDeviceGroup OBJECT-GROUP
    OBJECTS {
       scsiIntrDevTgtAccessMode,
       scsiIntrPortName,
       scsiIntrPortIdentifier,
       scsiAttTgtPortDscTgtIdx,
       scsiAttTgtPortName,
       scsiAttTgtPortIdentifier
    }
    STATUS current
    DESCRIPTION
      "This group is relevant for s SCSI initiator device and port."

Hallak-Stamler, et al. Standards Track [Page 71] RFC 4455 SCSI MIB April 2006

 ::= { scsiGroups 2 }
 scsiDiscoveryGroup OBJECT-GROUP
    OBJECTS {
       scsiDscTgtDevOrPort,
       scsiDscTgtName,
       scsiDscTgtConfigured,
       scsiDscTgtDiscovered,
       scsiDscTgtRowStatus,
       scsiDscTgtLastCreation,
       scsiDscLunLun,
       scsiDscLunIdCodeSet,
       scsiDscLunIdAssociation,
       scsiDscLunIdType,
       scsiDscLunIdValue
    }
    STATUS current
    DESCRIPTION
      "This group is relevant for the discovered SCSI target devices
      by a SCSI initiator port."
 ::= { scsiGroups 3 }
 scsiTargetDeviceGroup OBJECT-GROUP
    OBJECTS {
       scsiTgtDevNumberOfLUs,
       scsiTgtDeviceStatus,
       scsiTgtDevNonAccessibleLUs,
       scsiTgtPortName,
       scsiTgtPortIdentifier,
       scsiAttIntrPortAuthIntrIdx,
       scsiAttIntrPortName,
       scsiAttIntrPortIdentifier,
       scsiLuDefaultLun,
       scsiLuWwnName,
       scsiLuVendorId,
       scsiLuProductId,
       scsiLuRevisionId,
       scsiLuPeripheralType,
       scsiLuStatus,
       scsiLuState,
       scsiLuLastCreation,
       scsiLuIdCodeSet,
       scsiLuIdAssociation,
       scsiLuIdType,
       scsiLuIdValue
    }
    STATUS current
    DESCRIPTION

Hallak-Stamler, et al. Standards Track [Page 72] RFC 4455 SCSI MIB April 2006

      "This group is relevant for a SCSI target device and port."
 ::= { scsiGroups 4 }
 scsiLunMapGroup OBJECT-GROUP
    OBJECTS {
       scsiLunMapLuIndex,
       scsiLunMapRowStatus,
       scsiAuthIntrDevOrPort,
       scsiAuthIntrName,
       scsiAuthIntrLunMapIndex,
       scsiAuthIntrLastCreation,
       scsiAuthIntrRowStatus
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of attributes regarding the mapping
      between Logical Unit Number, logical unit, and target device."
 ::= { scsiGroups 5}
 scsiTargetDevStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiTgtDevResets,
       scsiTgtPortInCommands,
       scsiTgtPortWrittenMegaBytes,
       scsiTgtPortReadMegaBytes,
       scsiLuInCommands,
       scsiLuReadMegaBytes,
       scsiLuWrittenMegaBytes,
       scsiLuInResets,
       scsiLuOutTaskSetFullStatus
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of statistics for all
      implementations of the SCSI MIB module that contain SCSI target
      devices."
 ::= { scsiGroups 6}
 scsiTargetDevHSStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiTgtPortHSInCommands,
       scsiLuHSInCommands
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of high speed statistics for all
      implementations of the SCSI MIB module that contain SCSI target
      devices."

Hallak-Stamler, et al. Standards Track [Page 73] RFC 4455 SCSI MIB April 2006

 ::= { scsiGroups 7}
 scsiLunMapStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiAuthIntrAttachedTimes,
       scsiAuthIntrOutCommands,
       scsiAuthIntrReadMegaBytes,
       scsiAuthIntrWrittenMegaBytes
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of statistics regarding SCSI
      initiator devices authorized to attach local logical unit and
      SCSI target device."
 ::= { scsiGroups 8}
 scsiLunMapHSStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiAuthIntrHSOutCommands
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of high speed statistics regarding
      SCSI initiator devices authorized to attach local logical unit
      and SCSI target device."
 ::= { scsiGroups 9}
 scsiInitiatorDevStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiIntrDevOutResets,
       scsiIntrPortOutCommands,
       scsiIntrPortWrittenMegaBytes,
       scsiIntrPortReadMegaBytes
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of statistics for all
      implementations of the SCSI MIB module that contain SCSI
      initiator devices."
 ::= { scsiGroups 10}
 scsiInitiatorDevHSStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiIntrPortHSOutCommands
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of high speed statistics for all

Hallak-Stamler, et al. Standards Track [Page 74] RFC 4455 SCSI MIB April 2006

      implementations of the SCSI MIB module that contain SCSI
      initiator devices."
 ::= { scsiGroups 11}
 scsiDiscoveryStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiDscTgtInCommands,
       scsiDscTgtReadMegaBytes,
       scsiDscTgtWrittenMegaBytes
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of statistics for all
      implementations of the SCSI MIB module that contain discovered
      SCSI initiator devices."
 ::= { scsiGroups 12}
 scsiDiscoveryHSStatsGroup OBJECT-GROUP
    OBJECTS {
       scsiDscTgtHSInCommands
    }
    STATUS current
    DESCRIPTION
      "This group is a collection of high speed statistics for all
      implementations of the SCSI MIB module that contain discovered
      SCSI initiator devices."
 ::= { scsiGroups 13}
 scsiDeviceStatGroup OBJECT-GROUP
    OBJECTS {
       scsiPortBusyStatuses
    }
    STATUS current
    DESCRIPTION
      "A collection of statistics regarding SCSI devices and
      ports."
 ::= { scsiGroups 14 }
 scsiTgtDevLuNotificationsGroup NOTIFICATION-GROUP
    NOTIFICATIONS {
       scsiTgtDeviceStatusChanged,
       scsiLuStatusChanged
    }
    STATUS current
    DESCRIPTION
      "A collection of notifications regarding status change of SCSI
      target devices and logical units."
 ::= { scsiGroups 15 }

Hallak-Stamler, et al. Standards Track [Page 75] RFC 4455 SCSI MIB April 2006

 END

10. Object Population Example: SCSI Target and Initiator Devices on a

   pSCSI Bus
 This section provides a sample set of values for a parallel SCSI
 scenario in which a SCSI MIB module can be implemented.  The example
 shown below is not a normative part of this document and makes some
 assumptions about the underlying implementation, which are not based
 on actual implementations.
 The respective sections describe the sequence of object
 instantiations and attempts to explain non-typical values for
 attributes that are unique to the scenario.
 Note: While populating the objects, the population of statistics is
 not considered.
 This scenario deals with a SCSI target and initiator devices attached
 to a parallel SCSI bus, defined by one of the SCSI-3 Parallel
 Interface standards (the version referenced in the MIB module is the
 4th generation, called SPI-4).  We assume that the SCSI initiator
 device is a Host Bus Adaptor (HBA), and the SCSI target device is a
 physical disk.  We assume that the SCSI target device has one
 integrated logical unit, identified by a Logical Unit Number (LUN) of
 0, which is the default LUN.  The parallel SCSI transport only
 supports port identifiers, and not port names.  The transport pointer
 is set to 0 since there is no MIB module defined for SPI-4.
 We assume an HBA as the SCSI initiator device and a disk as the SCSI
 target device.  We assume that the SCSI target device has one logical
 unit, addressed by Logical Unit Number set to 0 (LUN0), which is the
 default LUN.  Parallel SCSI has only port identifiers, no port names.
 The transport pointer for parallel SCSI is set to 0 since there is no
 reference transport (SPI) MIB module.
 Once the SCSI system is initialized, an SNMP agent should be able to
 view the values of variables populated in the ScsiDevice,
 ScsiInitiatorDevice, ScsiTargetDevice, ScsiPort, ScsiTargetPort,
 ScsiInitiatorPort, ScsiLogicalUnit, ScsiLUIdentifier objects.
 The ScsiAuthorizedIntr population depends on the transport and the
 implementation.  As this example scenario is parallel SCSI, we deal
 with the ports.  Hence the ScsiPortIndexOrZero is the index of the
 SCSI target port and ScsiAuthIntrDevOrPort is "port".  Same is the
 case with the variables in scsiDscTgtDevOrPort.
 Note that "" means zero-length string.

Hallak-Stamler, et al. Standards Track [Page 76] RFC 4455 SCSI MIB April 2006

10.1. scsiInstance Table:

       Attribute                         Value
       ----------                        ------
       scsiInstIndex                      1
       scsiInstAlias                      "pSCSI-1"
       scsiInstSoftwareIndex              1000
       scsiInstVendorVersion              "1.0a"
       scsiInstScsiNotificationsEnable    true
       scsiInstStorageType                nonVolatile

10.2. scsiDevice Table:

       Attribute                Value
       ----------               ------
       scsiInstIndex            1                1
       scsiDeviceIndex          1                2
       scsiDeviceAlias          "pSCSI-HBA"      "pSCSI-Disk1"
       scsiDeviceRole           initiator(1)     target(0)
       scsiDevicePortNumber     1                1

10.3. scsiPort Table:

       Attribute                Value
       ----------               ------
       scsiInstIndex            1                1
       scsiDeviceIndex          1                2
       scsiPortIndex            1                2
       scsiPortRole             initiator(1)     target(0)
       scsiPortTransportPtr     1                2

10.4. scsiTransport Table:

       Attribute                Value
       ----------               ------
       scsiInstIndex            1                   1
       scsiDeviceIndex          1                   2
       scsiTransportIndex       1                   2
       scsiTransportType        scsiTransportSPI    scsiTransportSPI
       scsiTransportPointer     0.0                 0.0
       scsiTransportDevName     ""                  ""

Hallak-Stamler, et al. Standards Track [Page 77] RFC 4455 SCSI MIB April 2006

10.5. scsiIntrDev Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiIntrDevTgtAccessMode      autoEnable(2)

10.6. scsiInitiatorPort Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiPortIndex                 1
       scsiIntrPortName              ""
       scsiIntrPortIdentifier *1     0001b
  • 1 Port Identifier for SCSI is represented by 4 bits.

10.7. scsiDscTgt Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiDscTgtIntrPortIndex       1
       scsiDscTgtIndex               1
       scsiDscTgtDevOrPort           port(2)
       scsiDscTgtName                ""
       scsiDscTgtConfigured          false(2)
       scsiDscTgtDiscovered          true(1)
       scsiDscTgtRowStatus           active(1)

10.8. scsiDscLUN:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiDscTgtIntrPortIndex       1
       scsiDscTgtIndex               1
       scsiDscLunIndex               1
       scsiDscLunLun                 0

Hallak-Stamler, et al. Standards Track [Page 78] RFC 4455 SCSI MIB April 2006

10.9. scsiDscLUNIdentifier:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiDscLunIndex               1
       scsiDscLunIdIndex             1
       scsiDscLunIdCodeSet *1        2
       scsiDscLunIdAssociation *2    1
       scsiDscLunIdType        *3    1
       scsiDscLunIdValue             ASPENsl318203-001
  • 1 - The identifier field will have ASCII graphic codes.
  • 2 - The identifier is associated with the port that received

the request.

  • 3 - As defined in SPC. (This value specifies that the

scsiDscLunIdValue contains a vendorID in the first 8 bytes

      concatenated with the product identifier field and product
      serial number.)

10.10. scsiAttTgtPort Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               1
       scsiPortIndex                 1
       scsiAttTgtPortIndex           1
       scsiAttTgtPortDscTgtIdx       1
       scsiAttTgtPortName            ""
       scsiAttTgtPortId              0011b

10.11. scsiTgtDev Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiTgtDevNumberOfLUs         1
       scsiTgtDeviceStatus           available(2)
       scsiTgtDevNonAccessibleLUs    0

Hallak-Stamler, et al. Standards Track [Page 79] RFC 4455 SCSI MIB April 2006

10.12. scsiTgtPort Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiPortIndex                 2
       scsiPortName                  ""
       scsiTgtPortIdentifier         0010b

10.13. scsiLU Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiLuIndex                   1
       scsiLuDefaultLun              0
       scsiLuWwnName                 ""
       scsiLuVendorId                "xyz-corp"
       scsiLuProductId               "super turbo disk"
       scsiRevisionId                02
       scsiLUPeripheralType          00
       scsiLUStatus                  available(2)
       scsiLuState                   exposed(3)

10.14. scsiLuId Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiLuIndex                   1
       scsiLuIdIndex                 1
       scsiLuIdCodeSet *1            2
       scsiLuIdAssociation *2        1
       scsiLuIdType *3               1
       scsiLuIdValue                 ASPENsl318203-0004
  • 1 - The identifier field will have ASCII graphic codes.
  • 2 - The identifier is associated with the port that received

the request.

  • 3 - As defined in SPC. (This value specifies that the

LuIdValue contains a vendorID in the first 8 bytes concatenated

      with the product identifier field and product serial number.)

Hallak-Stamler, et al. Standards Track [Page 80] RFC 4455 SCSI MIB April 2006

10.15. scsiLunMap Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiLunMapIndex               1
       scsiLunMapLun                 0
       scsiLunMapLuIndex             1
       scsiLunMapLunRowStatus        active(1)

10.16. scsiAuthorizedIntr Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiAuthIntrTgtPortIndex      2
       scsiAuthIntrIndex             1
       scsiAuthIntrDevOrPort         port(2)
       scsiAuthIntrName              ""
       scsiAuthIntrLunMapIndex       1
       scsiAuthIntrRowStatus         active(1)

10.17. scsiAttIntrPort Table:

       Attribute                     Value
       ----------                    ------
       scsiInstIndex                 1
       scsiDeviceIndex               2
       scsiPortIndex                 2
       scsiAttIntrPortIdx            1
       scsiAttIntrPortAuthIntrIdx    1
       scsiAttIntrPortName           ""
       scsiAttIntrPortIdentifier     0011b

11. Security Considerations

 There are a number of management objects defined in this MIB module
 that have a MAX-ACCESS clause of read-write and/or read-create.  Such
 objects may be considered sensitive or vulnerable in some network
 environments.  The support for SET operations in a non-secure
 environment without proper protection can have a negative effect on
 network operations.  These are the following:
 o  scsiInstAlias, scsiInstScsiNotificationsEnable,
    scsiInstStorageType and scsiDeviceAlias: these objects can be
    manipulated to affect the management of a SCSI instance and its

Hallak-Stamler, et al. Standards Track [Page 81] RFC 4455 SCSI MIB April 2006

    devices; specifically, the SCSI instance's administrative alias,
    whether it generates notifications, whether its non-default
    parameter settings are retained over restarts, and the
    administrative alias for each of its devices.
 o  scsiIntrDevTgtAccessMode: this object can be manipulated to allow
    immediate access by local SCSI initiator devices to discovered
    SCSI target devices without waiting for administrator approval,
    where such approval might not be forthcoming.
 o  scsiDscTgtTable: the objects in this table can be manipulated to
    remove administrator-specified controls on access by local SCSI
    initiator devices to discovered SCSI target devices.
 o  scsiAuthorizedIntrTable: the objects in this table can be
    manipulated to remove administrator-specified controls on access
    by remote SCSI initiator devices to local SCSI target devices.
 o  scsiLunMapTable: the objects in this table can be manipulated to
    provide access by a remote SCSI initiator device to logical units
    that an administrator has configured as not accessible to said
    initiator.
 In each of the last four cases, the objects in the tables can also be
 manipulated to cause a denial of service attack, by preventing
 administrator-authorized access.
 Some of the readable objects in this MIB module (i.e., objects with a
 MAX-ACCESS other than not-accessible) may be considered sensitive or
 vulnerable in some network environments.  It is thus important to
 control even GET and/or NOTIFY access to these objects and possibly
 to even encrypt the values of these objects when sending them over
 the network via SNMP.  All seventeen of the tables in this MIB module
 contain information which might be considered sensitive to read
 access in some environments, e.g.,
 o  the settings of all read-write/read-create parameter objects
    mentioned above,
 o  scsiInstSoftwareIndex, scsiInstVendorVersion
    --which version of which software is running;
 o  scsiDeviceRole, scsiPortRole, scsiTransportType,
    scsiTransportPointer, scsiTransportDevName, scsiDscLunIdCodeSet,
    scsiDscLunIdAssociation, scsiDscLunIdType, scsiDscLunIdValue plus
    information in several tables: scsiTgtDevTable, scsiLuTable,
    scsiLuIdTable, scsiLunMapTable

Hallak-Stamler, et al. Standards Track [Page 82] RFC 4455 SCSI MIB April 2006

  1. -topology information indicating which devices/ports are targets,

about the transport protocols they use, and more specific

    information about such targets, including detailed information
    about the LUNs they expose and how they are mapped onto logical
    units;
 o  scsiIntrPortOutCommands,
    scsiIntrPortWrittenMegaBytes, scsiIntrPortReadMegaBytes,
    scsiIntrPortHSOutCommands scsiDscTgtInCommands,
    scsiDscTgtWrittenMegaBytes, scsiDscTgtReadMegaBytes,
    scsiDscTgtHSInCommands, scsiTgtPortInCommands,
    scsiTgtPortWrittenMegaBytes, scsiTgtPortReadMegaBytes,
    scsiTgtPortHSInCommands, scsiAuthIntrAttachedTimes,
    scsiAuthIntrOutCommands, scsiAuthIntrReadMegaBytes,
    scsiAuthIntrWrittenMegaBytes, scsiAuthIntrHSOutCommands,
    scsiLuInCommands, scsiLuReadMegaBytes, scsiLuWrittenMegaBytes,
    scsiLuHSInCommands
    -- statistics that could be used for traffic analysis.
 o  scsiAttTgtPortTable
    -- information on which initiators are connected to which targets
    that could be used for traffic analysis.
 o  scsiAuthorizedIntrTable and scsiAttIntrPortTable tables
    -- information about which initiators are authorized to connect to
    that targets.
 These information may need to be kept private in sensitive
 environments.
 SNMP versions prior to SNMPv3 did not include adequate security.
 Even if the network itself is secure (for example, by using IPsec),
 even then, there is no control as to who on the secure network is
 allowed to access and GET/SET (read/change/create/delete) the objects
 in this MIB module.
 It is RECOMMENDED that implementers consider the security features as
 provided by the SNMPv3 framework (see [RFC3410], section 8),
 including full support for the SNMPv3 cryptographic mechanisms (for
 authentication and privacy).
 Further, deployment of SNMP versions prior to SNMPv3 is NOT
 RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
 enable cryptographic security.  It is then a customer/operator
 responsibility to ensure that the SNMP entity giving access to an
 instance of this MIB module is properly configured to give access to
 the objects only to those principals (users) that have legitimate
 rights to indeed GET or SET (change/create/delete) them.

Hallak-Stamler, et al. Standards Track [Page 83] RFC 4455 SCSI MIB April 2006

12. Acknowledgements

 This document is the result of the work of the SCSI MIB Group.  In
 particular, the contributions of Sajay Selvaraj (HCL Technologies),
 George Penokie (IBM), and Roger Cummings (Veritas Software) were
 critical to the formulation of this specification.

13. IANA Considerations

 IANA has made a MIB OID assignment under the mib-2 branch for the
 SCSI-MIB.

14. References

14.1. Normative References

 [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
            Requirement Levels", BCP 14, RFC 2119, March 1997.
 [RFC2578]  McCloghrie, K., Perkins, D., and J. Schoenwaelder,
            "Structure of Management Information Version 2 (SMIv2)",
            STD 58, RFC 2578, April 1999.
 [RFC2579]  McCloghrie, K., Perkins, D., and J. Schoenwaelder,
            "Textual Conventions for SMIv2", STD 58, RFC 2579, April
            1999.
 [RFC2580]  McCloghrie, K., Perkins, D., and J. Schoenwaelder,
            "Conformance Statements for SMIv2", STD 58, RFC 2580,
            April 1999.
 [RFC2790]  Waldbusser, S. and P. Grillo, "Host Resources MIB", RFC
            2790, March 2000.
 [RFC3411]  Harrington, D., Presuhn, R., and B. Wijnen, "An
            Architecture for Describing Simple Network Management
            Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
            December 2002.
 [RFC3413]  Levi, D., Meyer, P., and B. Stewart, "Simple Network
            Management Protocol (SNMP) Applications", STD 62, RFC
            3413, December 2002.
 [SAM2]     ANSI INCITS 366-2003, "SCSI Architecture Model-2 (SAM-2)",
            SAM-2 Revision 24, September 2002.
 [SPC2]     ANSI INCITS 351-2001, "SCSI Primary Commands - 2 (SPC-2)",
            SPC-2 Revision 20, July 2001.

Hallak-Stamler, et al. Standards Track [Page 84] RFC 4455 SCSI MIB April 2006

14.2. Informative References

 [FCP2]     ANSI INCITS 350-2003, "Fibre Channel Protocol for SCSI
            (FCP-2)", FCP-2 Revision 08, September 2002.
 [ISCSI]    Bakke, M., "Definitions of Managed Objects for iSCSI",
            Work in Progress, October 2005.
 [RFC3410]  Case, J., Mundy, R., Partain, D., and B. Stewart,
            "Introduction and Applicability Statements for Internet-
            Standard Management Framework", RFC 3410, December 2002.
 [RFC3720]  Satran, J., Meth, K., Sapuntzakis, C., Chadalapaka, M.,
            and E. Zeidner, "Internet Small Computer Systems Interface
            (iSCSI)", RFC 3720, April 2004.
 [RFC4022]  Raghunarayan, R., "Management Information Base for the
            Transmission Control Protocol (TCP)", RFC 4022, March
            2005.
 [RFC4044]  McCloghrie, K., "Fibre Channel Management MIB", RFC 4044,
            May 2005.
 [SAS-1.1]  T10 Project #1601-D, "Serial Attached SCSI - 1.1 (SAS-
            1.1)", SAS-1.1 Revision 10, September 2005.
 [SBP3]     ANSI INCITS 375-2004, "Serial Bus Protocol 3 (SBP-3)",
            SBP-3 Revision 05, September 2003.
 [SCC2]     ANSI INCITS 318-1998, "SCSI Controller Commands - 2 (SCC-
            2)", SCC-2 Revision 04, September 1997.
 [SPI4]     ANSI INCITS 362-2002, "SCSI Parallel Interface-4 (SPI4)",
            SPI-4 Revision 10, May 2002.
 [SRP]      ANSI INCITS 365-2002, "SCSI RDMA Protocol (SRP)", SRP
            Revision 16a, July 2002.

Hallak-Stamler, et al. Standards Track [Page 85] RFC 4455 SCSI MIB April 2006

Authors' Addresses

 Michele Hallak-Stamler
 Sanrad Intelligent Storage
 27 Habarzel Street
 Tel Aviv  69710
 IL
 Phone: +972 3 7674809
 EMail: michele@sanrad.com
 URI:   http://www.sanrad.com/
 Mark Bakke
 Cisco Systems, Inc.
 7900 International Drive, Suite 400
 Bloomington, MN  55425
 USA
 EMail: mbakke@cisco.com
 URI:   http://www.cisco.com/
 Yaron Lederman
 Siliquent Technologies
 21 Etzel Street
 Ramat Gan
 IL
 Phone: +972 54 5308833
 EMail: yaronled@bezeqint.net
 Marjorie Krueger
 Hewlett-Packard
 8000 Foothills Blvd
 Roseville, CA  95747
 US
 Phone: +1 916-785-2656
 EMail: marjorie_krueger@hp.com

Hallak-Stamler, et al. Standards Track [Page 86] RFC 4455 SCSI MIB April 2006

 Keith McCloghrie
 Cisco Systems, Inc.
 170 West Tasman Drive
 San Jose, CA  95134
 US
 Phone: +1 408 526-5260
 EMail: kzm@cisco.com

Hallak-Stamler, et al. Standards Track [Page 87] RFC 4455 SCSI MIB April 2006

Full Copyright Statement

 Copyright (C) The Internet Society (2006).
 This document is subject to the rights, licenses and restrictions
 contained in BCP 78, and except as set forth therein, the authors
 retain all their rights.
 This document and the information contained herein are provided on an
 "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
 OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
 ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
 INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
 INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
 WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

 The IETF takes no position regarding the validity or scope of any
 Intellectual Property Rights or other rights that might be claimed to
 pertain to the implementation or use of the technology described in
 this document or the extent to which any license under such rights
 might or might not be available; nor does it represent that it has
 made any independent effort to identify any such rights.  Information
 on the procedures with respect to rights in RFC documents can be
 found in BCP 78 and BCP 79.
 Copies of IPR disclosures made to the IETF Secretariat and any
 assurances of licenses to be made available, or the result of an
 attempt made to obtain a general license or permission for the use of
 such proprietary rights by implementers or users of this
 specification can be obtained from the IETF on-line IPR repository at
 http://www.ietf.org/ipr.
 The IETF invites any interested party to bring to its attention any
 copyrights, patents or patent applications, or other proprietary
 rights that may cover technology that may be required to implement
 this standard.  Please address the information to the IETF at
 ietf-ipr@ietf.org.

Acknowledgement

 Funding for the RFC Editor function is provided by the IETF
 Administrative Support Activity (IASA).

Hallak-Stamler, et al. Standards Track [Page 88]

/data/webs/external/dokuwiki/data/pages/rfc/rfc4455.txt · Last modified: 2006/04/06 23:15 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki