GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc4379

Network Working Group K. Kompella Request for Comments: 4379 Juniper Networks, Inc. Updates: 1122 G. Swallow Category: Standards Track Cisco Systems, Inc.

                                                         February 2006
 Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures

Status of This Memo

 This document specifies an Internet standards track protocol for the
 Internet community, and requests discussion and suggestions for
 improvements.  Please refer to the current edition of the "Internet
 Official Protocol Standards" (STD 1) for the standardization state
 and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

 Copyright (C) The Internet Society (2006).

Abstract

 This document describes a simple and efficient mechanism that can be
 used to detect data plane failures in Multi-Protocol Label Switching
 (MPLS) Label Switched Paths (LSPs).  There are two parts to this
 document: information carried in an MPLS "echo request" and "echo
 reply" for the purposes of fault detection and isolation, and
 mechanisms for reliably sending the echo reply.

Table of Contents

 1. Introduction ....................................................2
    1.1. Conventions ................................................3
    1.2. Structure of This Document .................................3
    1.3. Contributors ...............................................3
 2. Motivation ......................................................4
    2.1. Use of Address Range 127/8 .................................4
 3. Packet Format ...................................................6
    3.1. Return Codes ..............................................10
    3.2. Target FEC Stack ..........................................11
         3.2.1. LDP IPv4 Prefix ....................................12
         3.2.2. LDP IPv6 Prefix ....................................13
         3.2.3. RSVP IPv4 LSP ......................................13
         3.2.4. RSVP IPv6 LSP ......................................14
         3.2.5. VPN IPv4 Prefix ....................................14
         3.2.6. VPN IPv6 Prefix ....................................15
         3.2.7. L2 VPN Endpoint ....................................16

Kompella & Swallow Standards Track [Page 1] RFC 4379 Detecting MPLS Data Plane Failures February 2006

         3.2.8. FEC 128 Pseudowire (Deprecated) ....................16
         3.2.9. FEC 128 Pseudowire (Current) .......................17
         3.2.10. FEC 129 Pseudowire ................................18
         3.2.11. BGP Labeled IPv4 Prefix ...........................19
         3.2.12. BGP Labeled IPv6 Prefix ...........................20
         3.2.13. Generic IPv4 Prefix ...............................20
         3.2.14. Generic IPv6 Prefix ...............................21
         3.2.15. Nil FEC ...........................................21
    3.3. Downstream Mapping ........................................22
         3.3.1. Multipath Information Encoding .....................26
         3.3.2. Downstream Router and Interface ....................28
    3.4. Pad TLV ...................................................29
    3.5. Vendor Enterprise Number ..................................29
    3.6. Interface and Label Stack .................................29
    3.7. Errored TLVs ..............................................31
    3.8. Reply TOS Byte TLV ........................................31
 4. Theory of Operation ............................................32
    4.1. Dealing with Equal-Cost Multi-Path (ECMP) .................32
    4.2. Testing LSPs That Are Used to Carry MPLS Payloads .........33
    4.3. Sending an MPLS Echo Request ..............................33
    4.4. Receiving an MPLS Echo Request ............................34
         4.4.1. FEC Validation .....................................40
    4.5. Sending an MPLS Echo Reply ................................41
    4.6. Receiving an MPLS Echo Reply ..............................42
    4.7. Issue with VPN IPv4 and IPv6 Prefixes .....................42
    4.8. Non-compliant Routers .....................................43
 5. References .....................................................43
    5.1. Normative References ......................................43
    5.2. Informative References ....................................44
 6. Security Considerations ........................................44
 7. IANA Considerations ............................................46
    7.1. Message Types, Reply Modes, Return Codes ..................46
    7.2. TLVs ......................................................47
 8. Acknowledgements ...............................................48

1. Introduction

 This document describes a simple and efficient mechanism that can be
 used to detect data plane failures in MPLS Label Switched Paths
 (LSPs).  There are two parts to this document: information carried in
 an MPLS "echo request" and "echo reply", and mechanisms for
 transporting the echo reply.  The first part aims at providing enough
 information to check correct operation of the data plane, as well as
 a mechanism to verify the data plane against the control plane, and
 thereby localize faults.  The second part suggests two methods of
 reliable reply channels for the echo request message for more robust
 fault isolation.

Kompella & Swallow Standards Track [Page 2] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 An important consideration in this design is that MPLS echo requests
 follow the same data path that normal MPLS packets would traverse.
 MPLS echo requests are meant primarily to validate the data plane,
 and secondarily to verify the data plane against the control plane.
 Mechanisms to check the control plane are valuable, but are not
 covered in this document.
 This document makes special use of the address range 127/8.  This is
 an exception to the behavior defined in RFC 1122 [RFC1122] and
 updates that RFC.  The motivation for this change and the details of
 this exceptional use are discussed in section 2.1 below.

1.1. Conventions

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in RFC 2119 [KEYWORDS].
 The term "Must Be Zero" (MBZ) is used in object descriptions for
 reserved fields.  These fields MUST be set to zero when sent and
 ignored on receipt.
 Terminology pertaining to L2 and L3 Virtual Private Networks (VPNs)
 is defined in [RFC4026].
 Since this document refers to the MPLS Time to Live (TTL) far more
 frequently than the IP TTL, the authors have chosen the convention of
 using the unqualified "TTL" to mean "MPLS TTL" and using "IP TTL" for
 the TTL value in the IP header.

1.2. Structure of This Document

 The body of this memo contains four main parts: motivation, MPLS echo
 request/reply packet format, LSP ping operation, and a reliable
 return path.  It is suggested that first-time readers skip the actual
 packet formats and read the Theory of Operation first; the document
 is structured the way it is to avoid forward references.

1.3. Contributors

 The following made vital contributions to all aspects of this
 document, and much of the material came out of debate and discussion
 among this group.
    Ronald P. Bonica, Juniper Networks, Inc.
    Dave Cooper, Global Crossing
    Ping Pan, Hammerhead Systems

Kompella & Swallow Standards Track [Page 3] RFC 4379 Detecting MPLS Data Plane Failures February 2006

    Nischal Sheth, Juniper Networks, Inc.
    Sanjay Wadhwa, Juniper Networks, Inc.

2. Motivation

 When an LSP fails to deliver user traffic, the failure cannot always
 be detected by the MPLS control plane.  There is a need to provide a
 tool that would enable users to detect such traffic "black holes" or
 misrouting within a reasonable period of time, and a mechanism to
 isolate faults.
 In this document, we describe a mechanism that accomplishes these
 goals.  This mechanism is modeled after the ping/traceroute paradigm:
 ping (ICMP echo request [ICMP]) is used for connectivity checks, and
 traceroute is used for hop-by-hop fault localization as well as path
 tracing.  This document specifies a "ping" mode and a "traceroute"
 mode for testing MPLS LSPs.
 The basic idea is to verify that packets that belong to a particular
 Forwarding Equivalence Class (FEC) actually end their MPLS path on a
 Label Switching Router (LSR) that is an egress for that FEC.  This
 document proposes that this test be carried out by sending a packet
 (called an "MPLS echo request") along the same data path as other
 packets belonging to this FEC.  An MPLS echo request also carries
 information about the FEC whose MPLS path is being verified.  This
 echo request is forwarded just like any other packet belonging to
 that FEC.  In "ping" mode (basic connectivity check), the packet
 should reach the end of the path, at which point it is sent to the
 control plane of the egress LSR, which then verifies whether it is
 indeed an egress for the FEC.  In "traceroute" mode (fault
 isolation), the packet is sent to the control plane of each transit
 LSR, which performs various checks that it is indeed a transit LSR
 for this path; this LSR also returns further information that helps
 check the control plane against the data plane, i.e., that forwarding
 matches what the routing protocols determined as the path.
 One way these tools can be used is to periodically ping an FEC to
 ensure connectivity.  If the ping fails, one can then initiate a
 traceroute to determine where the fault lies.  One can also
 periodically traceroute FECs to verify that forwarding matches the
 control plane; however, this places a greater burden on transit LSRs
 and thus should be used with caution.

2.1. Use of Address Range 127/8

 As described above, LSP ping is intended as a diagnostic tool.  It is
 intended to enable providers of an MPLS-based service to isolate
 network faults.  In particular, LSP ping needs to diagnose situations

Kompella & Swallow Standards Track [Page 4] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 where the control and data planes are out of sync.  It performs this
 by routing an MPLS echo request packet based solely on its label
 stack.  That is, the IP destination address is never used in a
 forwarding decision.  In fact, the sender of an MPLS echo request
 packet may not know, a priori, the address of the router at the end
 of the LSP.
 Providers of MPLS-based services also need the ability to trace all
 of the possible paths that an LSP may take.  Since most MPLS services
 are based on IP unicast forwarding, these paths are subject to
 equal-cost multi-path (ECMP) load sharing.
 This leads to the following requirements:
 1. Although the LSP in question may be broken in unknown ways, the
    likelihood of a diagnostic packet being delivered to a user of an
    MPLS service MUST be held to an absolute minimum.
 2. If an LSP is broken in such a way that it prematurely terminates,
    the diagnostic packet MUST NOT be IP forwarded.
 3. A means of varying the diagnostic packets such that they exercise
    all ECMP paths is thus REQUIRED.
 Clearly, using general unicast addresses satisfies neither of the
 first two requirements.  A number of other options for addresses were
 considered, including a portion of the private address space (as
 determined by the network operator) and the newly designated IPv4
 link local addresses.  Use of the private address space was deemed
 ineffective since the leading MPLS-based service is an IPv4 Virtual
 Private Network (VPN).  VPNs often use private addresses.
 The IPv4 link local addresses are more attractive in that the scope
 over which they can be forwarded is limited.  However, if one were to
 use an address from this range, it would still be possible for the
 first recipient of a diagnostic packet that "escaped" from a broken
 LSP to have that address assigned to the interface on which it
 arrived and thus could mistakenly receive such a packet.
 Furthermore, the IPv4 link local address range has only recently been
 allocated.  Many deployed routers would forward a packet with an
 address from that range toward the default route.
 The 127/8 range for IPv4 and that same range embedded in as IPv4-
 mapped IPv6 addresses for IPv6 was chosen for a number of reasons.
 RFC 1122 allocates the 127/8 as "Internal host loopback address" and
 states: "Addresses of this form MUST NOT appear outside a host."
 Thus, the default behavior of hosts is to discard such packets.  This

Kompella & Swallow Standards Track [Page 5] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 helps to ensure that if a diagnostic packet is misdirected to a host,
 it will be silently discarded.
 RFC 1812 [RFC1812] states:
    A router SHOULD NOT forward, except over a loopback interface, any
    packet that has a destination address on network 127.  A router
    MAY have a switch that allows the network manager to disable these
    checks.  If such a switch is provided, it MUST default to
    performing the checks.
 This helps to ensure that diagnostic packets are never IP forwarded.
 The 127/8 address range provides 16M addresses allowing wide
 flexibility in varying addresses to exercise ECMP paths.  Finally, as
 an implementation optimization, the 127/8 provides an easy means of
 identifying possible LSP packets.

3. Packet Format

 An MPLS echo request is a (possibly labeled) IPv4 or IPv6 UDP packet;
 the contents of the UDP packet have the following format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Version Number        |         Global Flags          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Message Type |   Reply mode  |  Return Code  | Return Subcode|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                        Sender's Handle                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                        Sequence Number                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    TimeStamp Sent (seconds)                   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  TimeStamp Sent (microseconds)                |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  TimeStamp Received (seconds)                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                TimeStamp Received (microseconds)              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            TLVs ...                           |
    .                                                               .
    .                                                               .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 6] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 The Version Number is currently 1.  (Note: the version number is to
 be incremented whenever a change is made that affects the ability of
 an implementation to correctly parse or process an MPLS echo
 request/reply.  These changes include any syntactic or semantic
 changes made to any of the fixed fields, or to any Type-Length-Value
 (TLV) or sub-TLV assignment or format that is defined at a certain
 version number.  The version number may not need to be changed if an
 optional TLV or sub-TLV is added.)
 The Global Flags field is a bit vector with the following format:
     0                   1
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             MBZ             |V|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 One flag is defined for now, the V bit; the rest MUST be set to zero
 when sending and ignored on receipt.
 The V (Validate FEC Stack) flag is set to 1 if the sender wants the
 receiver to perform FEC Stack validation; if V is 0, the choice is
 left to the receiver.
 The Message Type is one of the following:
    Value    Meaning
    -----    -------
        1    MPLS echo request
        2    MPLS echo reply
 The Reply Mode can take one of the following values:
    Value    Meaning
    -----    -------
        1    Do not reply
        2    Reply via an IPv4/IPv6 UDP packet
        3    Reply via an IPv4/IPv6 UDP packet with Router Alert
        4    Reply via application level control channel
 An MPLS echo request with 1 (Do not reply) in the Reply Mode field
 may be used for one-way connectivity tests; the receiving router may
 log gaps in the Sequence Numbers and/or maintain delay/jitter
 statistics.  An MPLS echo request would normally have 2 (Reply via an
 IPv4/IPv6 UDP packet) in the Reply Mode field.  If the normal IP
 return path is deemed unreliable, one may use 3 (Reply via an
 IPv4/IPv6 UDP packet with Router Alert).  Note that this requires
 that all intermediate routers understand and know how to forward MPLS

Kompella & Swallow Standards Track [Page 7] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 echo replies.  The echo reply uses the same IP version number as the
 received echo request, i.e., an IPv4 encapsulated echo reply is sent
 in response to an IPv4 encapsulated echo request.
 Some applications support an IP control channel.  One such example is
 the associated control channel defined in Virtual Circuit
 Connectivity Verification (VCCV) [VCCV].  Any application that
 supports an IP control channel between its control entities may set
 the Reply Mode to 4 (Reply via application level control channel) to
 ensure that replies use that same channel.  Further definition of
 this codepoint is application specific and thus beyond the scope of
 this document.
 Return Codes and Subcodes are described in the next section.
 The Sender's Handle is filled in by the sender, and returned
 unchanged by the receiver in the echo reply (if any).  There are no
 semantics associated with this handle, although a sender may find
 this useful for matching up requests with replies.
 The Sequence Number is assigned by the sender of the MPLS echo
 request and can be (for example) used to detect missed replies.
 The TimeStamp Sent is the time-of-day (in seconds and microseconds,
 according to the sender's clock) in NTP format [NTP] when the MPLS
 echo request is sent.  The TimeStamp Received in an echo reply is the
 time-of-day (according to the receiver's clock) in NTP format that
 the corresponding echo request was received.
 TLVs (Type-Length-Value tuples) have the following format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Type              |            Length             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                             Value                             |
    .                                                               .
    .                                                               .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Types are defined below; Length is the length of the Value field in
 octets.  The Value field depends on the Type; it is zero padded to
 align to a 4-octet boundary.  TLVs may be nested within other TLVs,
 in which case the nested TLVs are called sub-TLVs.  Sub-TLVs have
 independent types and MUST also be 4-octet aligned.

Kompella & Swallow Standards Track [Page 8] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Two examples follow.  The Label Distribution Protocol (LDP) IPv4 FEC
 sub-TLV has the following format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |    Type = 1 (LDP IPv4 FEC)    |          Length = 5           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv4 prefix                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 The Length for this TLV is 5.  A Target FEC Stack TLV that contains
 an LDP IPv4 FEC sub-TLV and a VPN IPv4 prefix sub-TLV has the
 following format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |      Type = 1 (FEC TLV)       |          Length = 12          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  sub-Type = 1 (LDP IPv4 FEC)  |          Length = 5           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv4 prefix                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | sub-Type = 6 (VPN IPv4 prefix)|          Length = 13          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Route Distinguisher                      |
    |                          (8 octets)                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         IPv4 prefix                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |                 Must Be Zero                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 9] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 A description of the Types and Values of the top-level TLVs for LSP
 ping are given below:
        Type #                  Value Field
        ------                  -----------
             1                  Target FEC Stack
             2                  Downstream Mapping
             3                  Pad
             4                  Not Assigned
             5                  Vendor Enterprise Number
             6                  Not Assigned
             7                  Interface and Label Stack
             8                  Not Assigned
             9                  Errored TLVs
            10                  Reply TOS Byte
 Types less than 32768 (i.e., with the high-order bit equal to 0) are
 mandatory TLVs that MUST either be supported by an implementation or
 result in the return code of 2 ("One or more of the TLVs was not
 understood") being sent in the echo response.
 Types greater than or equal to 32768 (i.e., with the high-order bit
 equal to 1) are optional TLVs that SHOULD be ignored if the
 implementation does not understand or support them.

3.1. Return Codes

 The Return Code is set to zero by the sender.  The receiver can set
 it to one of the values listed below.  The notation <RSC> refers to
 the Return Subcode.  This field is filled in with the stack-depth for
 those codes that specify that.  For all other codes, the Return
 Subcode MUST be set to zero.
        Value    Meaning
        -----    -------
            0    No return code
            1    Malformed echo request received
            2    One or more of the TLVs was not understood
            3    Replying router is an egress for the FEC at stack-
                 depth <RSC>
            4    Replying router has no mapping for the FEC at stack-
                 depth <RSC>

Kompella & Swallow Standards Track [Page 10] RFC 4379 Detecting MPLS Data Plane Failures February 2006

            5    Downstream Mapping Mismatch (See Note 1)
            6    Upstream Interface Index Unknown (See Note 1)
            7    Reserved
            8    Label switched at stack-depth <RSC>
            9    Label switched but no MPLS forwarding at stack-depth
                 <RSC>
           10    Mapping for this FEC is not the given label at stack-
                 depth <RSC>
           11    No label entry at stack-depth <RSC>
           12    Protocol not associated with interface at FEC stack-
                 depth <RSC>
           13    Premature termination of ping due to label stack
                 shrinking to a single label
 Note 1
    The Return Subcode contains the point in the label stack where
    processing was terminated.  If the RSC is 0, no labels were
    processed.  Otherwise the packet would have been label switched at
    depth RSC.

3.2. Target FEC Stack

 A Target FEC Stack is a list of sub-TLVs.  The number of elements is
 determined by looking at the sub-TLV length fields.
    Sub-Type       Length            Value Field
    --------       ------            -----------
           1            5            LDP IPv4 prefix
           2           17            LDP IPv6 prefix
           3           20            RSVP IPv4 LSP
           4           56            RSVP IPv6 LSP
           5                         Not Assigned
           6           13            VPN IPv4 prefix
           7           25            VPN IPv6 prefix
           8           14            L2 VPN endpoint
           9           10            "FEC 128" Pseudowire (deprecated)
          10           14            "FEC 128" Pseudowire
          11          16+            "FEC 129" Pseudowire
          12            5            BGP labeled IPv4 prefix

Kompella & Swallow Standards Track [Page 11] RFC 4379 Detecting MPLS Data Plane Failures February 2006

          13           17            BGP labeled IPv6 prefix
          14            5            Generic IPv4 prefix
          15           17            Generic IPv6 prefix
          16            4            Nil FEC
 Other FEC Types will be defined as needed.
 Note that this TLV defines a stack of FECs, the first FEC element
 corresponding to the top of the label stack, etc.
 An MPLS echo request MUST have a Target FEC Stack that describes the
 FEC Stack being tested.  For example, if an LSR X has an LDP mapping
 [LDP] for 192.168.1.1 (say, label 1001), then to verify that label
 1001 does indeed reach an egress LSR that announced this prefix via
 LDP, X can send an MPLS echo request with an FEC Stack TLV with one
 FEC in it, namely, of type LDP IPv4 prefix, with prefix
 192.168.1.1/32, and send the echo request with a label of 1001.
 Say LSR X wanted to verify that a label stack of <1001, 23456> is the
 right label stack to use to reach a VPN IPv4 prefix [see section
 3.2.5] of 10/8 in VPN foo.  Say further that LSR Y with loopback
 address 192.168.1.1 announced prefix 10/8 with Route Distinguisher
 RD-foo-Y (which may in general be different from the Route
 Distinguisher that LSR X uses in its own advertisements for VPN foo),
 label 23456 and BGP next hop 192.168.1.1 [BGP].  Finally, suppose
 that LSR X receives a label binding of 1001 for 192.168.1.1 via LDP.
 X has two choices in sending an MPLS echo request: X can send an MPLS
 echo request with an FEC Stack TLV with a single FEC of type VPN IPv4
 prefix with a prefix of 10/8 and a Route Distinguisher of RD-foo-Y.
 Alternatively, X can send an FEC Stack TLV with two FECs, the first
 of type LDP IPv4 with a prefix of 192.168.1.1/32 and the second of
 type of IP VPN with a prefix 10/8 with Route Distinguisher of RD-
 foo-Y.  In either case, the MPLS echo request would have a label
 stack of <1001, 23456>.  (Note: in this example, 1001 is the "outer"
 label and 23456 is the "inner" label.)

3.2.1. LDP IPv4 Prefix

 The IPv4 Prefix FEC is defined in [LDP].  When an LDP IPv4 prefix is
 encoded in a label stack, the following format is used.  The value
 consists of 4 octets of an IPv4 prefix followed by 1 octet of prefix
 length in bits; the format is given below.  The IPv4 prefix is in
 network byte order; if the prefix is shorter than 32 bits, trailing
 bits SHOULD be set to zero.  See [LDP] for an example of a Mapping
 for an IPv4 FEC.

Kompella & Swallow Standards Track [Page 12] RFC 4379 Detecting MPLS Data Plane Failures February 2006

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv4 prefix                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.2. LDP IPv6 Prefix

 The IPv6 Prefix FEC is defined in [LDP].  When an LDP IPv6 prefix is
 encoded in a label stack, the following format is used.  The value
 consists of 16 octets of an IPv6 prefix followed by 1 octet of prefix
 length in bits; the format is given below.  The IPv6 prefix is in
 network byte order; if the prefix is shorter than 128 bits, the
 trailing bits SHOULD be set to zero.  See [LDP] for an example of a
 Mapping for an IPv6 FEC.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv6 prefix                          |
    |                          (16 octets)                          |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.3. RSVP IPv4 LSP

 The value has the format below.  The value fields are taken from RFC
 3209, sections 4.6.1.1 and 4.6.2.1.  See [RSVP-TE].
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                 IPv4 tunnel end point address                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          Must Be Zero         |     Tunnel ID                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                       Extended Tunnel ID                      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   IPv4 tunnel sender address                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          Must Be Zero         |            LSP ID             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 13] RFC 4379 Detecting MPLS Data Plane Failures February 2006

3.2.4. RSVP IPv6 LSP

 The value has the format below.  The value fields are taken from RFC
 3209, sections 4.6.1.2 and 4.6.2.2.  See [RSVP-TE].
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                 IPv6 tunnel end point address                 |
    |                                                               |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          Must Be Zero         |          Tunnel ID            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                       Extended Tunnel ID                      |
    |                                                               |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   IPv6 tunnel sender address                  |
    |                                                               |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          Must Be Zero         |            LSP ID             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.5. VPN IPv4 Prefix

 VPN-IPv4 Network Layer Routing Information (NLRI) is defined in
 [RFC4365].  This document uses the term VPN IPv4 prefix for a VPN-
 IPv4 NLRI that has been advertised with an MPLS label in BGP.  See
 [BGP-LABEL].

Kompella & Swallow Standards Track [Page 14] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 When a VPN IPv4 prefix is encoded in a label stack, the following
 format is used.  The value field consists of the Route Distinguisher
 advertised with the VPN IPv4 prefix, the IPv4 prefix (with trailing 0
 bits to make 32 bits in all), and a prefix length, as follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Route Distinguisher                      |
    |                          (8 octets)                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         IPv4 prefix                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |                 Must Be Zero                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 The Route Distinguisher (RD) is an 8-octet identifier; it does not
 contain any inherent information.  The purpose of the RD is solely to
 allow one to create distinct routes to a common IPv4 address prefix.
 The encoding of the RD is not important here.  When matching this
 field to the local FEC information, it is treated as an opaque value.

3.2.6. VPN IPv6 Prefix

 VPN-IPv6 Network Layer Routing Information (NLRI) is defined in
 [RFC4365].  This document uses the term VPN IPv6 prefix for a VPN-
 IPv6 NLRI that has been advertised with an MPLS label in BGP.  See
 [BGP-LABEL].
 When a VPN IPv6 prefix is encoded in a label stack, the following
 format is used.  The value field consists of the Route Distinguisher
 advertised with the VPN IPv6 prefix, the IPv6 prefix (with trailing 0
 bits to make 128 bits in all), and a prefix length, as follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Route Distinguisher                      |
    |                          (8 octets)                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         IPv6 prefix                           |
    |                                                               |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |                 Must Be Zero                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 15] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 The Route Distinguisher is identical to the VPN IPv4 Prefix RD,
 except that it functions here to allow the creation of distinct
 routes to IPv6 prefixes.  See section 3.2.5.  When matching this
 field to local FEC information, it is treated as an opaque value.

3.2.7. L2 VPN Endpoint

 VPLS stands for Virtual Private LAN Service.  The terms VPLS BGP NLRI
 and VE ID (VPLS Edge Identifier) are defined in [VPLS-BGP].  This
 document uses the simpler term L2 VPN endpoint when referring to a
 VPLS BGP NLRI.  The Route Distinguisher is an 8-octet identifier used
 to distinguish information about various L2 VPNs advertised by a
 node.  The VE ID is a 2-octet identifier used to identify a
 particular node that serves as the service attachment point within a
 VPLS.  The structure of these two identifiers is unimportant here;
 when matching these fields to local FEC information, they are treated
 as opaque values.  The encapsulation type is identical to the PW Type
 in section 3.2.8 below.
 When an L2 VPN endpoint is encoded in a label stack, the following
 format is used.  The value field consists of a Route Distinguisher (8
 octets), the sender (of the ping)'s VE ID (2 octets), the receiver's
 VE ID (2 octets), and an encapsulation type (2 octets), formatted as
 follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Route Distinguisher                      |
    |                          (8 octets)                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Sender's VE ID        |       Receiver's VE ID        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |      Encapsulation Type       |         Must Be Zero          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.8. FEC 128 Pseudowire (Deprecated)

 FEC 128 (0x80) is defined in [PW-CONTROL], as are the terms PW ID
 (Pseudowire ID) and PW Type (Pseudowire Type).  A PW ID is a non-zero
 32-bit connection ID.  The PW Type is a 15-bit number indicating the
 encapsulation type.  It is carried right justified in the field below
 termed encapsulation type with the high-order bit set to zero.  Both
 of these fields are treated in this protocol as opaque values.

Kompella & Swallow Standards Track [Page 16] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 When an FEC 128 is encoded in a label stack, the following format is
 used.  The value field consists of the remote PE address (the
 destination address of the targeted LDP session), the PW ID, and the
 encapsulation type as follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Remote PE Address                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                             PW ID                             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            PW Type            |          Must Be Zero         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 This FEC is deprecated and is retained only for backward
 compatibility.  Implementations of LSP ping SHOULD accept and process
 this TLV, but SHOULD send LSP ping echo requests with the new TLV
 (see next section), unless explicitly configured to use the old TLV.
 An LSR receiving this TLV SHOULD use the source IP address of the LSP
 echo request to infer the sender's PE address.

3.2.9. FEC 128 Pseudowire (Current)

 FEC 128 (0x80) is defined in [PW-CONTROL], as are the terms PW ID
 (Pseudowire ID) and PW Type (Pseudowire Type).  A PW ID is a non-zero
 32-bit connection ID.  The PW Type is a 15-bit number indicating the
 encapsulation type.  It is carried right justified in the field below
 termed encapsulation type with the high-order bit set to zero.
 Both of these fields are treated in this protocol as opaque values.
 When matching these field to the local FEC information, the match
 MUST be exact.

Kompella & Swallow Standards Track [Page 17] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 When an FEC 128 is encoded in a label stack, the following format is
 used.  The value field consists of the sender's PE address (the
 source address of the targeted LDP session), the remote PE address
 (the destination address of the targeted LDP session), the PW ID, and
 the encapsulation type as follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                     Sender's PE Address                       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Remote PE Address                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                             PW ID                             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            PW Type            |          Must Be Zero         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.10. FEC 129 Pseudowire

 FEC 129 (0x81) and the terms PW Type, Attachment Group Identifier
 (AGI), Attachment Group Identifier Type (AGI Type), Attachment
 Individual Identifier Type (AII Type), Source Attachment Individual
 Identifier (SAII), and Target Attachment Individual Identifier (TAII)
 are defined in [PW-CONTROL].  The PW Type is a 15-bit number
 indicating the encapsulation type.  It is carried right justified in
 the field below PW Type with the high-order bit set to zero.  All the
 other fields are treated as opaque values and copied directly from
 the FEC 129 format.  All of these values together uniquely define the
 FEC within the scope of the LDP session identified by the source and
 remote PE addresses.

Kompella & Swallow Standards Track [Page 18] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 When an FEC 129 is encoded in a label stack, the following format is
 used.  The Length of this TLV is 16 + AGI length + SAII length + TAII
 length.  Padding is used to make the total length a multiple of 4;
 the length of the padding is not included in the Length field.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                     Sender's PE Address                       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Remote PE Address                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            PW Type            |   AGI Type    |  AGI Length   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    ~                           AGI Value                           ~
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   AII Type    |  SAII Length  |      SAII Value               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    ~                    SAII Value (continued)                     ~
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   AII Type    |  TAII Length  |      TAII Value               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    ~                    TAII Value (continued)                     ~
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  TAII (cont.) |  0-3 octets of zero padding                   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.11. BGP Labeled IPv4 Prefix

 BGP labeled IPv4 prefixes are defined in [BGP-LABEL].  When a BGP
 labeled IPv4 prefix is encoded in a label stack, the following format
 is used.  The value field consists the IPv4 prefix (with trailing 0
 bits to make 32 bits in all), and the prefix length, as follows:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv4 Prefix                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |                 Must Be Zero                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 19] RFC 4379 Detecting MPLS Data Plane Failures February 2006

3.2.12. BGP Labeled IPv6 Prefix

 BGP labeled IPv6 prefixes are defined in [BGP-LABEL].  When a BGP
 labeled IPv6 prefix is encoded in a label stack, the following format
 is used.  The value consists of 16 octets of an IPv6 prefix followed
 by 1 octet of prefix length in bits; the format is given below.  The
 IPv6 prefix is in network byte order; if the prefix is shorter than
 128 bits, the trailing bits SHOULD be set to zero.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv6 prefix                          |
    |                          (16 octets)                          |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.13. Generic IPv4 Prefix

 The value consists of 4 octets of an IPv4 prefix followed by 1 octet
 of prefix length in bits; the format is given below.  The IPv4 prefix
 is in network byte order; if the prefix is shorter than 32 bits,
 trailing bits SHOULD be set to zero.  This FEC is used if the
 protocol advertising the label is unknown or may change during the
 course of the LSP.  An example is an inter-AS LSP that may be
 signaled by LDP in one Autonomous System (AS), by RSVP-TE [RSVP-TE]
 in another AS, and by BGP between the ASes, such as is common for
 inter-AS VPNs.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv4 prefix                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 20] RFC 4379 Detecting MPLS Data Plane Failures February 2006

3.2.14. Generic IPv6 Prefix

 The value consists of 16 octets of an IPv6 prefix followed by 1 octet
 of prefix length in bits; the format is given below.  The IPv6 prefix
 is in network byte order; if the prefix is shorter than 128 bits, the
 trailing bits SHOULD be set to zero.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          IPv6 prefix                          |
    |                          (16 octets)                          |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Prefix Length |         Must Be Zero                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.2.15. Nil FEC

 At times, labels from the reserved range, e.g., Router Alert and
 Explicit-null, may be added to the label stack for various diagnostic
 purposes such as influencing load-balancing.  These labels may have
 no explicit FEC associated with them.  The Nil FEC Stack is defined
 to allow a Target FEC Stack sub-TLV to be added to the Target FEC
 Stack to account for such labels so that proper validation can still
 be performed.
 The Length is 4.  Labels are 20-bit values treated as numbers.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                 Label                 |          MBZ          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Label is the actual label value inserted in the label stack; the MBZ
 fields MUST be zero when sent and ignored on receipt.

Kompella & Swallow Standards Track [Page 21] RFC 4379 Detecting MPLS Data Plane Failures February 2006

3.3. Downstream Mapping

 The Downstream Mapping object is a TLV that MAY be included in an
 echo request message.  Only one Downstream Mapping object may appear
 in an echo request.  The presence of a Downstream Mapping object is a
 request that Downstream Mapping objects be included in the echo
 reply.  If the replying router is the destination of the FEC, then a
 Downstream Mapping TLV SHOULD NOT be included in the echo reply.
 Otherwise the replying router SHOULD include a Downstream Mapping
 object for each interface over which this FEC could be forwarded.
 For a more precise definition of the notion of "downstream", see
 section 3.3.2, "Downstream Router and Interface".
 The Length is K + M + 4*N octets, where M is the Multipath Length,
 and N is the number of Downstream Labels.  Values for K are found in
 the description of Address Type below.  The Value field of a
 Downstream Mapping has the following format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               MTU             | Address Type  |    DS Flags   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Downstream IP Address (4 or 16 octets)            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Downstream Interface Address (4 or 16 octets)         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Multipath Type| Depth Limit   |        Multipath Length       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                     (Multipath Information)                   .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               Downstream Label                |    Protocol   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               Downstream Label                |    Protocol   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Maximum Transmission Unit (MTU)
    The MTU is the size in octets of the largest MPLS frame (including
    label stack) that fits on the interface to the Downstream LSR.

Kompella & Swallow Standards Track [Page 22] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Address Type
    The Address Type indicates if the interface is numbered or
    unnumbered.  It also determines the length of the Downstream IP
    Address and Downstream Interface fields.  The resulting total for
    the initial part of the TLV is listed in the table below as "K
    Octets".  The Address Type is set to one of the following values:
       Type #        Address Type           K Octets
       ------        ------------           --------
            1        IPv4 Numbered                16
            2        IPv4 Unnumbered              16
            3        IPv6 Numbered                40
            4        IPv6 Unnumbered              28
 DS Flags
    The DS Flags field is a bit vector with the following format:
        0 1 2 3 4 5 6 7
       +-+-+-+-+-+-+-+-+
       | Rsvd(MBZ) |I|N|
       +-+-+-+-+-+-+-+-+
    Two flags are defined currently, I and N.  The remaining flags
    MUST be set to zero when sending and ignored on receipt.
    Flag  Name and Meaning
    ----  ----------------
       I  Interface and Label Stack Object Request
          When this flag is set, it indicates that the replying
          router SHOULD include an Interface and Label Stack
          Object in the echo reply message.
       N  Treat as a Non-IP Packet
          Echo request messages will be used to diagnose non-IP
          flows.  However, these messages are carried in IP
          packets.  For a router that alters its ECMP algorithm
          based on the FEC or deep packet examination, this flag
          requests that the router treat this as it would if the
          determination of an IP payload had failed.

Kompella & Swallow Standards Track [Page 23] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Downstream IP Address and Downstream Interface Address
    IPv4 addresses and interface indices are encoded in 4 octets; IPv6
    addresses are encoded in 16 octets.
    If the interface to the downstream LSR is numbered, then the
    Address Type MUST be set to IPv4 or IPv6, the Downstream IP
    Address MUST be set to either the downstream LSR's Router ID or
    the interface address of the downstream LSR, and the Downstream
    Interface Address MUST be set to the downstream LSR's interface
    address.
    If the interface to the downstream LSR is unnumbered, the Address
    Type MUST be IPv4 Unnumbered or IPv6 Unnumbered, the Downstream IP
    Address MUST be the downstream LSR's Router ID, and the Downstream
    Interface Address MUST be set to the index assigned by the
    upstream LSR to the interface.
    If an LSR does not know the IP address of its neighbor, then it
    MUST set the Address Type to either IPv4 Unnumbered or IPv6
    Unnumbered.  For IPv4, it must set the Downstream IP Address to
    127.0.0.1; for IPv6 the address is set to 0::1.  In both cases,
    the interface index MUST be set to 0.  If an LSR receives an Echo
    Request packet with either of these addresses in the Downstream IP
    Address field, this indicates that it MUST bypass interface
    verification but continue with label validation.
    If the originator of an Echo Request packet wishes to obtain
    Downstream Mapping information but does not know the expected
    label stack, then it SHOULD set the Address Type to either IPv4
    Unnumbered or IPv6 Unnumbered.  For IPv4, it MUST set the
    Downstream IP Address to 224.0.0.2; for IPv6 the address MUST be
    set to FF02::2.  In both cases, the interface index MUST be set to
    0.  If an LSR receives an Echo Request packet with the all-routers
    multicast address, then this indicates that it MUST bypass both
    interface and label stack validation, but return Downstream
    Mapping TLVs using the information provided.

Kompella & Swallow Standards Track [Page 24] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Multipath Type
    The following Multipath Types are defined:
    Key   Type                  Multipath Information
    ---   ----------------      ---------------------
     0    no multipath          Empty (Multipath Length = 0)
     2    IP address            IP addresses
     4    IP address range      low/high address pairs
     8    Bit-masked IP         IP address prefix and bit mask
            address set
     9    Bit-masked label set  Label prefix and bit mask
    Type 0 indicates that all packets will be forwarded out this one
    interface.
    Types 2, 4, 8, and 9 specify that the supplied Multipath
    Information will serve to exercise this path.
 Depth Limit
    The Depth Limit is applicable only to a label stack and is the
    maximum number of labels considered in the hash; this SHOULD be
    set to zero if unspecified or unlimited.
 Multipath Length
    The length in octets of the Multipath Information.
 Multipath Information
    Address or label values encoded according to the Multipath Type.
    See the next section below for encoding details.
 Downstream Label(s)
    The set of labels in the label stack as it would have appeared if
    this router were forwarding the packet through this interface.
    Any Implicit Null labels are explicitly included.  Labels are
    treated as numbers, i.e., they are right justified in the field.
    A Downstream Label is 24 bits, in the same format as an MPLS label
    minus the TTL field, i.e., the MSBit of the label is bit 0, the
    LSBit is bit 19, the EXP bits are bits 20-22, and bit 23 is the S
    bit.  The replying router SHOULD fill in the EXP and S bits; the
    LSR receiving the echo reply MAY choose to ignore these bits.

Kompella & Swallow Standards Track [Page 25] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Protocol
    The Protocol is taken from the following table:
    Protocol #        Signaling Protocol
    ----------        ------------------
             0        Unknown
             1        Static
             2        BGP
             3        LDP
             4        RSVP-TE

3.3.1. Multipath Information Encoding

 The Multipath Information encodes labels or addresses that will
 exercise this path.  The Multipath Information depends on the
 Multipath Type.  The contents of the field are shown in the table
 above.  IPv4 addresses are drawn from the range 127/8; IPv6 addresses
 are drawn from the range 0:0:0:0:0:FFFF:127/104.  Labels are treated
 as numbers, i.e., they are right justified in the field.  For Type 4,
 ranges indicated by Address pairs MUST NOT overlap and MUST be in
 ascending sequence.
 Type 8 allows a more dense encoding of IP addresses.  The IP prefix
 is formatted as a base IP address with the non-prefix low-order bits
 set to zero.  The maximum prefix length is 27.  Following the prefix
 is a mask of length 2^(32-prefix length) bits for IPv4 and 2^(128-
 prefix length) bits for IPv6.  Each bit set to 1 represents a valid
 address.  The address is the base IPv4 address plus the position of
 the bit in the mask where the bits are numbered left to right
 beginning with zero.  For example, the IPv4 addresses 127.2.1.0,
 127.2.1.5-127.2.1.15, and 127.2.1.20-127.2.1.29 would be encoded as
 follows:
  0                   1                   2                   3
  0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 1 1 1 1 1 1 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 26] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Those same addresses embedded in IPv6 would be encoded as follows:
  0                   1                   2                   3
  0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |0 1 1 1 1 1 1 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 |1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0|
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Type 9 allows a more dense encoding of labels.  The label prefix is
 formatted as a base label value with the non-prefix low-order bits
 set to zero.  The maximum prefix (including leading zeros due to
 encoding) length is 27.  Following the prefix is a mask of length
 2^(32-prefix length) bits.  Each bit set to one represents a valid
 label.  The label is the base label plus the position of the bit in
 the mask where the bits are numbered left to right beginning with
 zero.  Label values of all the odd numbers between 1152 and 1279
 would be encoded as follows:
  0                   1                   2                   3
  0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 0
 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0| +-+-+-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 1 0 1
 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1| +-+-+-+-+-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 1 0 1 0 1
 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1| +-+-+-+-+-+-+-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 1 0 1 0 1 0 1
 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1| +-+-+-+-+-+-+-+-+-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 1 0 1 0 1 0 1 0 1
 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1| +-+-+-+-+-+-+-+-+-
 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 If the received Multipath Information is non-null, the labels and IP
 addresses MUST be picked from the set provided.  If none of these
 labels or addresses map to a particular downstream interface, then
 for that interface, the type MUST be set to 0.  If the received
 Multipath Information is null (i.e., Multipath Length = 0, or for
 Types 8 and 9, a mask of all zeros), the type MUST be set to 0.

Kompella & Swallow Standards Track [Page 27] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 For example, suppose LSR X at hop 10 has two downstream LSRs, Y and
 Z, for the FEC in question.  The received X could return Multipath
 Type 4, with low/high IP addresses of 127.1.1.1->127.1.1.255 for
 downstream LSR Y and 127.2.1.1->127.2.1.255 for downstream LSR Z.
 The head end reflects this information to LSR Y.  Y, which has three
 downstream LSRs, U, V, and W, computes that 127.1.1.1->127.1.1.127
 would go to U and 127.1.1.128-> 127.1.1.255 would go to V.  Y would
 then respond with 3 Downstream Mappings: to U, with Multipath Type 4
 (127.1.1.1->127.1.1.127); to V, with Multipath Type 4
 (127.1.1.127->127.1.1.255); and to W, with Multipath Type 0.
 Note that computing Multipath Information may impose a significant
 processing burden on the receiver.  A receiver MAY thus choose to
 process a subset of the received prefixes.  The sender, on receiving
 a reply to a Downstream Mapping with partial information, SHOULD
 assume that the prefixes missing in the reply were skipped by the
 receiver, and MAY re-request information about them in a new echo
 request.

3.3.2. Downstream Router and Interface

 The notion of "downstream router" and "downstream interface" should
 be explained.  Consider an LSR X.  If a packet that was originated
 with TTL n>1 arrived with outermost label L and TTL=1 at LSR X, X
 must be able to compute which LSRs could receive the packet if it was
 originated with TTL=n+1, over which interface the request would
 arrive and what label stack those LSRs would see.  (It is outside the
 scope of this document to specify how this computation is done.)  The
 set of these LSRs/interfaces consists of the downstream
 routers/interfaces (and their corresponding labels) for X with
 respect to L.  Each pair of downstream router and interface requires
 a separate Downstream Mapping to be added to the reply.
 The case where X is the LSR originating the echo request is a special
 case.  X needs to figure out what LSRs would receive the MPLS echo
 request for a given FEC Stack that X originates with TTL=1.
 The set of downstream routers at X may be alternative paths (see the
 discussion below on ECMP) or simultaneous paths (e.g., for MPLS
 multicast).  In the former case, the Multipath Information is used as
 a hint to the sender as to how it may influence the choice of these
 alternatives.

Kompella & Swallow Standards Track [Page 28] RFC 4379 Detecting MPLS Data Plane Failures February 2006

3.4. Pad TLV

 The value part of the Pad TLV contains a variable number (>= 1) of
 octets.  The first octet takes values from the following table; all
 the other octets (if any) are ignored.  The receiver SHOULD verify
 that the TLV is received in its entirety, but otherwise ignores the
 contents of this TLV, apart from the first octet.
    Value        Meaning
    -----        -------
        1        Drop Pad TLV from reply
        2        Copy Pad TLV to reply
    3-255        Reserved for future use

3.5. Vendor Enterprise Number

 SMI Private Enterprise Numbers are maintained by IANA.  The Length is
 always 4; the value is the SMI Private Enterprise code, in network
 octet order, of the vendor with a Vendor Private extension to any of
 the fields in the fixed part of the message, in which case this TLV
 MUST be present.  If none of the fields in the fixed part of the
 message have Vendor Private extensions, inclusion of this TLV is
 OPTIONAL.  Vendor Private ranges for Message Types, Reply Modes, and
 Return Codes have been defined.  When any of these are used, the
 Vendor Enterprise Number TLV MUST be included in the message.

3.6. Interface and Label Stack

 The Interface and Label Stack TLV MAY be included in a reply message
 to report the interface on which the request message was received and
 the label stack that was on the packet when it was received.  Only
 one such object may appear.  The purpose of the object is to allow
 the upstream router to obtain the exact interface and label stack
 information as it appears at the replying LSR.

Kompella & Swallow Standards Track [Page 29] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 The Length is K + 4*N octets; N is the number of labels in the label
 stack.  Values for K are found in the description of Address Type
 below.  The Value field of a Downstream Mapping has the following
 format:
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Address Type  |             Must Be Zero                      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   IP Address (4 or 16 octets)                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   Interface (4 or 16 octets)                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                                                               .
    .                          Label Stack                          .
    .                                                               .
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Address Type
    The Address Type indicates if the interface is numbered or
    unnumbered.  It also determines the length of the IP Address and
    Interface fields.  The resulting total for the initial part of the
    TLV is listed in the table below as "K Octets".  The Address Type
    is set to one of the following values:
       Type #        Address Type           K Octets
       ------        ------------           --------
            1        IPv4 Numbered                12
            2        IPv4 Unnumbered              12
            3        IPv6 Numbered                36
            4        IPv6 Unnumbered              24
 IP Address and Interface
    IPv4 addresses and interface indices are encoded in 4 octets; IPv6
    addresses are encoded in 16 octets.
    If the interface upon which the echo request message was received
    is numbered, then the Address Type MUST be set to IPv4 or IPv6,
    the IP Address MUST be set to either the LSR's Router ID or the
    interface address, and the Interface MUST be set to the interface
    address.

Kompella & Swallow Standards Track [Page 30] RFC 4379 Detecting MPLS Data Plane Failures February 2006

    If the interface is unnumbered, the Address Type MUST be either
    IPv4 Unnumbered or IPv6 Unnumbered, the IP Address MUST be the
    LSR's Router ID, and the Interface MUST be set to the index
    assigned to the interface.
 Label Stack
    The label stack of the received echo request message.  If any TTL
    values have been changed by this router, they SHOULD be restored.

3.7. Errored TLVs

 The following TLV is a TLV that MAY be included in an echo reply to
 inform the sender of an echo request of mandatory TLVs either not
 supported by an implementation or parsed and found to be in error.
 The Value field contains the TLVs that were not understood, encoded
 as sub-TLVs.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Type = 9          |            Length             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                             Value                             |
    .                                                               .
    .                                                               .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.8. Reply TOS Byte TLV

 This TLV MAY be used by the originator of the echo request to request
 that an echo reply be sent with the IP header TOS byte set to the
 value specified in the TLV.  This TLV has a length of 4 with the
 following value field.
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Reply-TOS Byte|                 Must Be Zero                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Kompella & Swallow Standards Track [Page 31] RFC 4379 Detecting MPLS Data Plane Failures February 2006

4. Theory of Operation

 An MPLS echo request is used to test a particular LSP.  The LSP to be
 tested is identified by the "FEC Stack"; for example, if the LSP was
 set up via LDP, and is to an egress IP address of 10.1.1.1, the FEC
 Stack contains a single element, namely, an LDP IPv4 prefix sub-TLV
 with value 10.1.1.1/32.  If the LSP being tested is an RSVP LSP, the
 FEC Stack consists of a single element that captures the RSVP Session
 and Sender Template that uniquely identifies the LSP.
 FEC Stacks can be more complex.  For example, one may wish to test a
 VPN IPv4 prefix of 10.1/8 that is tunneled over an LDP LSP with
 egress 10.10.1.1.  The FEC Stack would then contain two sub-TLVs, the
 bottom being a VPN IPv4 prefix, and the top being an LDP IPv4 prefix.
 If the underlying (LDP) tunnel were not known, or was considered
 irrelevant, the FEC Stack could be a single element with just the VPN
 IPv4 sub-TLV.
 When an MPLS echo request is received, the receiver is expected to
 verify that the control plane and data plane are both healthy (for
 the FEC Stack being pinged) and that the two planes are in sync.  The
 procedures for this are in section 4.4 below.

4.1. Dealing with Equal-Cost Multi-Path (ECMP)

 LSPs need not be simple point-to-point tunnels.  Frequently, a single
 LSP may originate at several ingresses, and terminate at several
 egresses; this is very common with LDP LSPs.  LSPs for a given FEC
 may also have multiple "next hops" at transit LSRs.  At an ingress,
 there may also be several different LSPs to choose from to get to the
 desired endpoint.  Finally, LSPs may have backup paths, detour paths,
 and other alternative paths to take should the primary LSP go down.
 To deal with the last two first: it is assumed that the LSR sourcing
 MPLS echo requests can force the echo request into any desired LSP,
 so choosing among multiple LSPs at the ingress is not an issue.  The
 problem of probing the various flavors of backup paths that will
 typically not be used for forwarding data unless the primary LSP is
 down will not be addressed here.
 Since the actual LSP and path that a given packet may take may not be
 known a priori, it is useful if MPLS echo requests can exercise all
 possible paths.  This, although desirable, may not be practical,
 because the algorithms that a given LSR uses to distribute packets
 over alternative paths may be proprietary.
 To achieve some degree of coverage of alternate paths, there is a
 certain latitude in choosing the destination IP address and source

Kompella & Swallow Standards Track [Page 32] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 UDP port for an MPLS echo request.  This is clearly not sufficient;
 in the case of traceroute, more latitude is offered by means of the
 Multipath Information of the Downstream Mapping TLV.  This is used as
 follows.  An ingress LSR periodically sends an MPLS traceroute
 message to determine whether there are multipaths for a given LSP.
 If so, each hop will provide some information how each of its
 downstream paths can be exercised.  The ingress can then send MPLS
 echo requests that exercise these paths.  If several transit LSRs
 have ECMP, the ingress may attempt to compose these to exercise all
 possible paths.  However, full coverage may not be possible.

4.2. Testing LSPs That Are Used to Carry MPLS Payloads

 To detect certain LSP breakages, it may be necessary to encapsulate
 an MPLS echo request packet with at least one additional label when
 testing LSPs that are used to carry MPLS payloads (such as LSPs used
 to carry L2VPN and L3VPN traffic.  For example, when testing LDP or
 RSVP-TE LSPs, just sending an MPLS echo request packet may not detect
 instances where the router immediately upstream of the destination of
 the LSP ping may forward the MPLS echo request successfully over an
 interface not configured to carry MPLS payloads because of the use of
 penultimate hop popping.  Since the receiving router has no means to
 differentiate whether the IP packet was sent unlabeled or implicitly
 labeled, the addition of labels shimmed above the MPLS echo request
 (using the Nil FEC) will prevent a router from forwarding such a
 packet out unlabeled interfaces.

4.3. Sending an MPLS Echo Request

 An MPLS echo request is a UDP packet.  The IP header is set as
 follows: the source IP address is a routable address of the sender;
 the destination IP address is a (randomly chosen) IPv4 address from
 the range 127/8 or IPv6 address from the range
 0:0:0:0:0:FFFF:127/104.  The IP TTL is set to 1.  The source UDP port
 is chosen by the sender; the destination UDP port is set to 3503
 (assigned by IANA for MPLS echo requests).  The Router Alert option
 MUST be set in the IP header.
 An MPLS echo request is sent with a label stack corresponding to the
 FEC Stack being tested.  Note that further labels could be applied
 if, for example, the normal route to the topmost FEC in the stack is
 via a Traffic Engineered Tunnel [RSVP-TE].  If all of the FECs in the
 stack correspond to Implicit Null labels, the MPLS echo request is
 considered unlabeled even if further labels will be applied in
 sending the packet.
 If the echo request is labeled, one MAY (depending on what is being
 pinged) set the TTL of the innermost label to 1, to prevent the ping

Kompella & Swallow Standards Track [Page 33] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 request going farther than it should.  Examples of where this SHOULD
 be done include pinging a VPN IPv4 or IPv6 prefix, an L2 VPN endpoint
 or a pseudowire.  Preventing the ping request from going too far can
 also be accomplished by inserting a Router Alert label above this
 label; however, this may lead to the undesired side effect that MPLS
 echo requests take a different data path than actual data.  For more
 information on how these mechanisms can be used for pseudowire
 connectivity verification, see [VCCV].
 In "ping" mode (end-to-end connectivity check), the TTL in the
 outermost label is set to 255.  In "traceroute" mode (fault isolation
 mode), the TTL is set successively to 1, 2, and so on.
 The sender chooses a Sender's Handle and a Sequence Number.  When
 sending subsequent MPLS echo requests, the sender SHOULD increment
 the Sequence Number by 1.  However, a sender MAY choose to send a
 group of echo requests with the same Sequence Number to improve the
 chance of arrival of at least one packet with that Sequence Number.
 The TimeStamp Sent is set to the time-of-day (in seconds and
 microseconds) that the echo request is sent.  The TimeStamp Received
 is set to zero.
 An MPLS echo request MUST have an FEC Stack TLV.  Also, the Reply
 Mode must be set to the desired reply mode; the Return Code and
 Subcode are set to zero.  In the "traceroute" mode, the echo request
 SHOULD include a Downstream Mapping TLV.

4.4. Receiving an MPLS Echo Request

 Sending an MPLS echo request to the control plane is triggered by one
 of the following packet processing exceptions: Router Alert option,
 IP TTL expiration, MPLS TTL expiration, MPLS Router Alert label, or
 the destination address in the 127/8 address range.  The control
 plane further identifies it by UDP destination port 3503.
 For reporting purposes the bottom of stack is considered to be
 stack-depth of 1.  This is to establish an absolute reference for the
 case where the actual stack may have more labels than there are FECs
 in the Target FEC Stack.
 Furthermore, in all the error codes listed in this document, a
 stack-depth of 0 means "no value specified".  This allows
 compatibility with existing implementations that do not use the
 Return Subcode field.
 An LSR X that receives an MPLS echo request then processes it as
 follows.

Kompella & Swallow Standards Track [Page 34] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 1. General packet sanity is verified.  If the packet is not well-
    formed, LSR X SHOULD send an MPLS Echo Reply with the Return Code
    set to "Malformed echo request received" and the Subcode to zero.
    If there are any TLVs not marked as "Ignore" that LSR X does not
    understand, LSR X SHOULD send an MPLS "TLV not understood" (as
    appropriate), and the Subcode set to zero.  In the latter case,
    the misunderstood TLVs (only) are included as sub-TLVs in an
    Errored TLVs TLV in the reply.  The header fields Sender's Handle,
    Sequence Number, and Timestamp Sent are not examined, but are
    included in the MPLS echo reply message.
 The algorithm uses the following variables and identifiers:
 Interface-I:       the interface on which the MPLS echo request was
                    received.
 Stack-R:           the label stack on the packet as it was received.
 Stack-D:           the label stack carried in the Downstream Mapping
                    TLV (not always present)
 Label-L:           the label from the actual stack currently being
                    examined.  Requires no initialization.
 Label-stack-depth: the depth of label being verified.  Initialized to
                    the number of labels in the received label stack
                    S.
 FEC-stack-depth:   depth of the FEC in the Target FEC Stack that
                    should be used to verify the current actual label.
                    Requires no initialization.
 Best-return-code:  contains the return code for the echo reply packet
                    as currently best known.  As algorithm progresses,
                    this code may change depending on the results of
                    further checks that it performs.
 Best-rtn-subcode:  similar to Best-return-code, but for the Echo
                    Reply Subcode.
 FEC-status:        result value returned by the FEC Checking
                    algorithm described in section 4.4.1.
 /* Save receive context information */

Kompella & Swallow Standards Track [Page 35] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 2. If the echo request is good, LSR X stores the interface over
    which the echo was received in Interface-I, and the label stack
    with which it came in Stack-R.
 /* The rest of the algorithm iterates over the labels in Stack-R,
    verifies validity of label values, reports associated label
    switching operations (for traceroute), verifies correspondence
    between the Stack-R and the Target FEC Stack description in the
    body of the echo request, and reports any errors. */
 /* The algorithm iterates as follows. */
 3. Label Validation:
    If Label-stack-depth is 0 {
    /* The LSR needs to report its being a tail-end for the LSP */
       Set FEC-stack-depth to 1, set Label-L to 3 (Implicit Null).
       Set Best-return-code to 3 ("Replying router is an egress for
       the FEC at stack depth"), set Best-rtn-subcode to the
       value of FEC-stack-depth (1) and go to step 5 (Egress
       Processing).
    }
    /* This step assumes there is always an entry for well-known
       label values */
    Set Label-L to the value extracted from Stack-R at depth
    Label-stack-depth.  Look up Label-L in the Incoming Label Map
    (ILM) to determine if the label has been allocated and an
    operation is associated with it.
    If there is no entry for L {
    /* Indicates a temporary or permanent label synchronization
       problem the LSR needs to report an error */
       Set Best-return-code to 11 ("No label entry at stack-depth")
       and Best-rtn-subcode to Label-stack-depth.  Go to step 7
       (Send Reply Packet).
    }
    Else {
       Retrieve the associated label operation from the
       corresponding NLFE and proceed to step 4 (Label Operation
       check).

Kompella & Swallow Standards Track [Page 36] RFC 4379 Detecting MPLS Data Plane Failures February 2006

    }
 4. Label Operation Check
    If the label operation is "Pop and Continue Processing" {
    /* Includes Explicit Null and Router Alert label cases */
       Iterate to the next label by decrementing Label-stack-depth
       and loop back to step 3 (Label Validation).
    }
    If the label operation is "Swap or Pop and Switch based on Popped
       Label" {
       Set Best-return-code to 8 ("Label switched at stack-depth")
       and Best-rtn-subcode to Label-stack-depth to report transit
       switching.
       If a Downstream Mapping TLV is present in the received echo
       request {
          If the IP address in the TLV is 127.0.0.1 or 0::1 {
             Set Best-return-code to 6 ("Upstream Interface Index
             Unknown").  An Interface and Label Stack TLV SHOULD be
             included in the reply and filled with Interface-I and
             Stack-R.
          }
          Else {
             Verify that the IP address, interface address, and label
             stack in the Downstream Mapping TLV match Interface-I
             and Stack-R.  If there is a mismatch, set
             Best-return-code to 5, "Downstream Mapping Mismatch".
             An Interface and Label Stack TLV SHOULD be included in
             the reply and filled in based on Interface-I and
             Stack-R.  Go to step 7 (Send Reply Packet).
          }
       }
       For each available downstream ECMP path {
          Retrieve output interface from the NHLFE entry.
          /* Note: this return code is set even if Label-stack-depth
             is one */

Kompella & Swallow Standards Track [Page 37] RFC 4379 Detecting MPLS Data Plane Failures February 2006

          If the output interface is not MPLS enabled {
             Set Best-return-code to Return Code 9, "Label switched
             but no MPLS forwarding at stack-depth" and set
             Best-rtn-subcode to Label-stack-depth and goto
             Send_Reply_Packet.
          }
          If a Downstream Mapping TLV is present {
            A Downstream Mapping TLV SHOULD be included in the echo
            reply (see section 3.3) filled in with information about
            the current ECMP path.
          }
       }
       If no Downstream Mapping TLV is present, or the Downstream IP
          Address is set to the ALLROUTERS multicast address,
             go to step 7 (Send Reply Packet).
       If the "Validate FEC Stack" flag is not set and the LSR is not
       configured to perform FEC checking by default, go to step 7
       (Send Reply Packet).
    /* Validate the Target FEC Stack in the received echo request.
       First determine FEC-stack-depth from the Downstream Mapping
       TLV.  This is done by walking through Stack-D (the Downstream
       labels) from the bottom, decrementing the number of labels
       for each non-Implicit Null label, while incrementing
       FEC-stack-depth for each label.  If the Downstream Mapping TLV
       contains one or more Implicit Null labels, FEC-stack-depth
       may be greater than Label-stack-depth.  To be consistent with
       the above stack-depths, the bottom is considered to entry 1.
       */
       Set FEC-stack-depth to 0.  Set i to Label-stack-depth.
       While (i > 0 ) do {
          ++FEC-stack-depth.
          if Stack-D[FEC-stack-depth] != 3 (Implicit Null)
             --i.
       }
       If the number of labels in the FEC stack is greater
          than or equal to FEC-stack-depth {

Kompella & Swallow Standards Track [Page 38] RFC 4379 Detecting MPLS Data Plane Failures February 2006

          Perform the FEC Checking procedure (see subsection 4.4.1
          below).
          If FEC-status is 2, set Best-return-code to 10 ("Mapping
          for this FEC is not the given label at stack-depth").
          If the return code is 1, set Best-return-code to
          FEC-return-code and Best-rtn-subcode to FEC-stack-depth.
       }
       Go to step 7 (Send Reply Packet).
    }
 5. Egress Processing:
    /* These steps are performed by the LSR that identified itself
       as the tail-end LSR for an LSP. */
    If received echo request contains no Downstream Mapping TLV, or
       the Downstream IP Address is set to 127.0.0.1 or 0::1
          go to step 6 (Egress FEC Validation).
    Verify that the IP address, interface address, and label stack in
    the Downstream Mapping TLV match Interface-I and Stack-R.  If
    not, set Best-return-code to 5, "Downstream Mapping
    Mis-match".  A Received Interface and Label Stack TLV SHOULD be
    created for the echo response packet.  Go to step 7 (Send Reply
    Packet).
 6. Egress FEC Validation:
    /* This is a loop for all entries in the Target FEC Stack
       starting with FEC-stack-depth. */
    Perform FEC checking by following the algorithm described in
    subsection 4.4.1 for Label-L and the FEC at FEC-stack-depth.
    Set Best-return-code to FEC-code and Best-rtn-subcode to the
    value in FEC-stack-depth.
    If FEC-status (the result of the check) is 1,
       go to step 7 (Send Reply Packet).
    /* Iterate to the next FEC entry */
    ++FEC-stack-depth.

Kompella & Swallow Standards Track [Page 39] RFC 4379 Detecting MPLS Data Plane Failures February 2006

    If FEC-stack-depth > the number of FECs in the FEC-stack,
       go to step 7 (Send Reply Packet).
    If FEC-status is 0 {
       ++Label-stack-depth.
       If Label-stack-depth > the number of labels in Stack-R,
          Go to step 7 (Send Reply Packet).
       Label-L = extracted label from Stack-R at depth
          Label-stack-depth.
       Loop back to step 6 (Egress FEC Validation).
    }
 7. Send Reply Packet:
    Send an MPLS echo reply with a Return Code of Best-return-code,
    and a Return Subcode of Best-rtn-subcode.  Include any TLVs
    created during the above process.  The procedures for sending
    the echo reply are found in subsection 4.4.1.

4.4.1. FEC Validation

 /* This subsection describes validation of an FEC entry within the
    Target FEC Stack and accepts an FEC, Label-L, and Interface-I.
    The algorithm performs the following steps. */
 1. Two return values, FEC-status and FEC-return-code, are initialized
    to 0.
 2. If the FEC is the Nil FEC {
       If Label-L is either Explicit_Null or Router_Alert, return.
       Else {
          Set FEC-return-code to 10 ("Mapping for this FEC is not
          the given label at stack-depth").
          Set FEC-status to 1
          Return.
       }
    }
 3. Check the FEC label mapping that describes how traffic received on
    the LSP is further switched or which application it is associated
    with.  If no mapping exists, set FEC-return-code to Return 4,
    "Replying router has no mapping for the FEC at stack-depth".  Set
    FEC-status to 1.  Return.
 4. If the label mapping for FEC is Implicit Null, set FEC-status to 2
    and proceed to step 5.  Otherwise, if the label mapping for FEC is

Kompella & Swallow Standards Track [Page 40] RFC 4379 Detecting MPLS Data Plane Failures February 2006

    Label-L, proceed to step 5.  Otherwise, set FEC-return-code to 10
    ("Mapping for this FEC is not the given label at stack-depth"),
    set FEC-status to 1, and return.
 5. This is a protocol check.  Check what protocol would be used to
    advertise FEC.  If it can be determined that no protocol
    associated with Interface-I would have advertised an FEC of that
    FEC-Type, set FEC-return-code to 12 ("Protocol not associated with
    interface at FEC stack-depth").  Set FEC-status to 1.
 6. Return.

4.5. Sending an MPLS Echo Reply

 An MPLS echo reply is a UDP packet.  It MUST ONLY be sent in response
 to an MPLS echo request.  The source IP address is a routable address
 of the replier; the source port is the well-known UDP port for LSP
 ping.  The destination IP address and UDP port are copied from the
 source IP address and UDP port of the echo request.  The IP TTL is
 set to 255.  If the Reply Mode in the echo request is "Reply via an
 IPv4 UDP packet with Router Alert", then the IP header MUST contain
 the Router Alert IP option.  If the reply is sent over an LSP, the
 topmost label MUST in this case be the Router Alert label (1) (see
 [LABEL-STACK]).
 The format of the echo reply is the same as the echo request.  The
 Sender's Handle, the Sequence Number, and TimeStamp Sent are copied
 from the echo request; the TimeStamp Received is set to the time-of-
 day that the echo request is received (note that this information is
 most useful if the time-of-day clocks on the requester and the
 replier are synchronized).  The FEC Stack TLV from the echo request
 MAY be copied to the reply.
 The replier MUST fill in the Return Code and Subcode, as determined
 in the previous subsection.
 If the echo request contains a Pad TLV, the replier MUST interpret
 the first octet for instructions regarding how to reply.
 If the replying router is the destination of the FEC, then Downstream
 Mapping TLVs SHOULD NOT be included in the echo reply.
 If the echo request contains a Downstream Mapping TLV, and the
 replying router is not the destination of the FEC, the replier SHOULD
 compute its downstream routers and corresponding labels for the
 incoming label, and add Downstream Mapping TLVs for each one to the
 echo reply it sends back.

Kompella & Swallow Standards Track [Page 41] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 If the Downstream Mapping TLV contains Multipath Information
 requiring more processing than the receiving router is willing to
 perform, the responding router MAY choose to respond with only a
 subset of multipaths contained in the echo request Downstream
 Mapping.  (Note: The originator of the echo request MAY send another
 echo request with the Multipath Information that was not included in
 the reply.)
 Except in the case of Reply Mode 4, "Reply via application level
 control channel", echo replies are always sent in the context of the
 IP/MPLS network.

4.6. Receiving an MPLS Echo Reply

 An LSR X should only receive an MPLS echo reply in response to an
 MPLS echo request that it sent.  Thus, on receipt of an MPLS echo
 reply, X should parse the packet to ensure that it is well-formed,
 then attempt to match up the echo reply with an echo request that it
 had previously sent, using the destination UDP port and the Sender's
 Handle.  If no match is found, then X jettisons the echo reply;
 otherwise, it checks the Sequence Number to see if it matches.
 If the echo reply contains Downstream Mappings, and X wishes to
 traceroute further, it SHOULD copy the Downstream Mapping(s) into its
 next echo request(s) (with TTL incremented by one).

4.7. Issue with VPN IPv4 and IPv6 Prefixes

 Typically, an LSP ping for a VPN IPv4 prefix or VPN IPv6 prefix is
 sent with a label stack of depth greater than 1, with the innermost
 label having a TTL of 1.  This is to terminate the ping at the egress
 PE, before it gets sent to the customer device.  However, under
 certain circumstances, the label stack can shrink to a single label
 before the ping hits the egress PE; this will result in the ping
 terminating prematurely.  One such scenario is a multi-AS Carrier's
 Carrier VPN.
 To get around this problem, one approach is for the LSR that receives
 such a ping to realize that the ping terminated prematurely, and send
 back error code 13.  In that case, the initiating LSR can retry the
 ping after incrementing the TTL on the VPN label.  In this fashion,
 the ingress LSR will sequentially try TTL values until it finds one
 that allows the VPN ping to reach the egress PE.

Kompella & Swallow Standards Track [Page 42] RFC 4379 Detecting MPLS Data Plane Failures February 2006

4.8. Non-compliant Routers

 If the egress for the FEC Stack being pinged does not support MPLS
 ping, then no reply will be sent, resulting in possible "false
 negatives".  If in "traceroute" mode, a transit LSR does not support
 LSP ping, then no reply will be forthcoming from that LSR for some
 TTL, say, n.  The LSR originating the echo request SHOULD try sending
 the echo request with TTL=n+1, n+2, ..., n+k to probe LSRs further
 down the path.  In such a case, the echo request for TTL > n SHOULD
 be sent with Downstream Mapping TLV "Downstream IP Address" field set
 to the ALLROUTERs multicast address until a reply is received with a
 Downstream Mapping TLV.  The label stack MAY be omitted from the
 Downstream Mapping TLV.  Furthermore, the "Validate FEC Stack" flag
 SHOULD NOT be set until an echo reply packet with a Downstream
 Mapping TLV is received.

5. References

5.1. Normative References

 [BGP]          Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
                Protocol 4 (BGP-4)", RFC 4271, January 2006.
 [IANA]         Narten, T. and H. Alvestrand, "Guidelines for Writing
                an IANA Considerations Section in RFCs", BCP 26, RFC
                2434, October 1998.
 [KEYWORDS]     Bradner, S., "Key words for use in RFCs to Indicate
                Requirement Levels", BCP 14, RFC 2119, March 1997.
 [LABEL-STACK]  Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
                Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
                Encoding", RFC 3032, January 2001.
 [NTP]          Mills, D., "Simple Network Time Protocol (SNTP)
                Version 4 for IPv4, IPv6 and OSI", RFC 2030, October
                1996.
 [RFC1122]      Braden, R., "Requirements for Internet Hosts -
                Communication Layers", STD 3, RFC 1122, October 1989.
 [RFC1812]      Baker, F., "Requirements for IP Version 4 Routers",
                RFC 1812, June 1995.
 [RFC4026]      Andersson, L. and T. Madsen, "Provider Provisioned
                Virtual Private Network (VPN) Terminology", RFC 4026,
                March 2005.

Kompella & Swallow Standards Track [Page 43] RFC 4379 Detecting MPLS Data Plane Failures February 2006

5.2. Informative References

 [BGP-LABEL]    Rekhter, Y. and E. Rosen, "Carrying Label Information
                in BGP-4", RFC 3107, May 2001.
 [ICMP]         Postel, J., "Internet Control Message Protocol", STD
                5, RFC 792, September 1981.
 [LDP]          Andersson, L., Doolan, P., Feldman, N., Fredette, A.,
                and B. Thomas, "LDP Specification", RFC 3036, January
                2001.
 [PW-CONTROL]   Martini, L., El-Aawar, N., Heron, G., Rosen, E.,
                Tappan, D., and  T. Smith, "Pseudowire Setup and
                Maintenance using the Label Distribution Protocol",
                Work in Progress.
 [RFC4365]      Rosen, E., "Applicability Statement for BGP/MPLS IP
                Virtual Private Networks (VPNs)", RFC 4365, February
                2006.
 [RSVP-TE]      Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan,
                V., and G. Swallow, "RSVP-TE: Extensions to RSVP for
                LSP Tunnels", RFC 3209, December 2001.
 [VCCV]         Nadeau, T. and R. Aggarwal, "Pseudo Wire Virtual
                Circuit Connectivity Verification (VCCV), Work in
                Progress, August 2005.
 [VPLS-BGP]     Kompella, K. and Y. Rekhter, "Virtual Private LAN
                Service", Work in Progress.

6. Security Considerations

 Overall, the security needs for LSP ping are similar to those of ICMP
 ping.
 There are at least three approaches to attacking LSRs using the
 mechanisms defined here.  One is a Denial-of-Service attack, by
 sending MPLS echo requests/replies to LSRs and thereby increasing
 their workload.  The second is obfuscating the state of the MPLS data
 plane liveness by spoofing, hijacking, replaying, or otherwise
 tampering with MPLS echo requests and replies.  The third is an
 unauthorized source using an LSP ping to obtain information about the
 network.

Kompella & Swallow Standards Track [Page 44] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 To avoid potential Denial-of-Service attacks, it is RECOMMENDED that
 implementations regulate the LSP ping traffic going to the control
 plane.  A rate limiter SHOULD be applied to the well-known UDP port
 defined below.
 Unsophisticated replay and spoofing attacks involving faking or
 replaying MPLS echo reply messages are unlikely to be effective.
 These replies would have to match the Sender's Handle and Sequence
 Number of an outstanding MPLS echo request message.  A non-matching
 replay would be discarded as the sequence has moved on, thus a spoof
 has only a small window of opportunity.  However, to provide a
 stronger defense, an implementation MAY also validate the TimeStamp
 Sent by requiring and exact match on this field.
 To protect against unauthorized sources using MPLS echo request
 messages to obtain network information, it is RECOMMENDED that
 implementations provide a means of checking the source addresses of
 MPLS echo request messages against an access list before accepting
 the message.
 It is not clear how to prevent hijacking (non-delivery) of echo
 requests or replies; however, if these messages are indeed hijacked,
 LSP ping will report that the data plane is not working as it should.
 It does not seem vital (at this point) to secure the data carried in
 MPLS echo requests and replies, although knowledge of the state of
 the MPLS data plane may be considered confidential by some.
 Implementations SHOULD, however, provide a means of filtering the
 addresses to which echo reply messages may be sent.
 Although this document makes special use of 127/8 address, these are
 used only in conjunction with the UDP port 3503.  Furthermore, these
 packets are only processed by routers.  All other hosts MUST treat
 all packets with a destination address in the range 127/8 in
 accordance to RFC 1122.  Any packet received by a router with a
 destination address in the range 127/8 without a destination UDP port
 of 3503 MUST be treated in accordance to RFC 1812.  In particular,
 the default behavior is to treat packets destined to a 127/8 address
 as "martians".

Kompella & Swallow Standards Track [Page 45] RFC 4379 Detecting MPLS Data Plane Failures February 2006

7. IANA Considerations

 The TCP and UDP port number 3503 has been allocated by IANA for LSP
 echo requests and replies.
 The following sections detail the new name spaces to be managed by
 IANA.  For each of these name spaces, the space is divided into
 assignment ranges; the following terms are used in describing the
 procedures by which IANA allocates values: "Standards Action" (as
 defined in [IANA]), "Specification Required", and "Vendor Private
 Use".
 Values from "Specification Required" ranges MUST be registered with
 IANA.  The request MUST be made via an Experimental RFC that
 describes the format and procedures for using the code point; the
 actual assignment is made during the IANA actions for the RFC.
 Values from "Vendor Private" ranges MUST NOT be registered with IANA;
 however, the message MUST contain an enterprise code as registered
 with the IANA SMI Private Network Management Private Enterprise
 Numbers.  For each name space that has a Vendor Private range, it
 must be specified where exactly the SMI Private Enterprise Number
 resides; see below for examples.  In this way, several enterprises
 (vendors) can use the same code point without fear of collision.

7.1. Message Types, Reply Modes, Return Codes

 The IANA has created and will maintain registries for Message Types,
 Reply Modes, and Return Codes.  Each of these can take values in the
 range 0-255.  Assignments in the range 0-191 are via Standards
 Action; assignments in the range 192-251 are made via "Specification
 Required"; values in the range 252-255 are for Vendor Private Use,
 and MUST NOT be allocated.
 If any of these fields fall in the Vendor Private range, a top-level
 Vendor Enterprise Number TLV MUST be present in the message.
 Message Types defined in this document are the following:
    Value    Meaning
    -----    -------
        1    MPLS echo request
        2    MPLS echo reply

Kompella & Swallow Standards Track [Page 46] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 Reply Modes defined in this document are the following:
    Value    Meaning
    -----    -------
        1    Do not reply
        2    Reply via an IPv4/IPv6 UDP packet
        3    Reply via an IPv4/IPv6 UDP packet with Router Alert
        4    Reply via application level control channel
 Return Codes defined in this document are listed in section 3.1.

7.2. TLVs

 The IANA has created and will maintain a registry for the Type field
 of top-level TLVs as well as for any associated sub-TLVs.  Note the
 meaning of a sub-TLV is scoped by the TLV.  The number spaces for the
 sub-TLVs of various TLVs are independent.
 The valid range for TLVs and sub-TLVs is 0-65535.  Assignments in the
 range 0-16383 and 32768-49161 are made via Standards Action as
 defined in [IANA]; assignments in the range 16384-31743 and
 49162-64511 are made via "Specification Required" as defined above;
 values in the range 31744-32767 and 64512-65535 are for Vendor
 Private Use, and MUST NOT be allocated.
 If a TLV or sub-TLV has a Type that falls in the range for Vendor
 Private Use, the Length MUST be at least 4, and the first four octets
 MUST be that vendor's SMI Private Enterprise Number, in network octet
 order.  The rest of the Value field is private to the vendor.

Kompella & Swallow Standards Track [Page 47] RFC 4379 Detecting MPLS Data Plane Failures February 2006

 TLVs and sub-TLVs defined in this document are the following:
       Type       Sub-Type        Value Field
       ----       --------        -----------
          1                       Target FEC Stack
                       1          LDP IPv4 prefix
                       2          LDP IPv6 prefix
                       3          RSVP IPv4 LSP
                       4          RSVP IPv6 LSP
                       5          Not Assigned
                       6          VPN IPv4 prefix
                       7          VPN IPv6 prefix
                       8          L2 VPN endpoint
                       9          "FEC 128" Pseudowire (Deprecated)
                      10          "FEC 128" Pseudowire
                      11          "FEC 129" Pseudowire
                      12          BGP labeled IPv4 prefix
                      13          BGP labeled IPv6 prefix
                      14          Generic IPv4 prefix
                      15          Generic IPv6 prefix
                      16          Nil FEC
          2                       Downstream Mapping
          3                       Pad
          4                       Not Assigned
          5                       Vendor Enterprise Number
          6                       Not Assigned
          7                       Interface and Label Stack
          8                       Not Assigned
          9                       Errored TLVs
                  Any value       The TLV not understood
         10                       Reply TOS Byte

8. Acknowledgements

 This document is the outcome of many discussions among many people,
 including Manoj Leelanivas, Paul Traina, Yakov Rekhter, Der-Hwa Gan,
 Brook Bailey, Eric Rosen, Ina Minei, Shivani Aggarwal, and Vanson
 Lim.
 The description of the Multipath Information sub-field of the
 Downstream Mapping TLV was adapted from text suggested by Curtis
 Villamizar.

Kompella & Swallow Standards Track [Page 48] RFC 4379 Detecting MPLS Data Plane Failures February 2006

Authors' Addresses

 Kireeti Kompella
 Juniper Networks
 1194 N.Mathilda Ave
 Sunnyvale, CA 94089
 EMail:  kireeti@juniper.net
 George Swallow
 Cisco Systems
 1414 Massachusetts Ave,
 Boxborough, MA 01719
 Phone:  +1 978 936 1398
 EMail:  swallow@cisco.com

Kompella & Swallow Standards Track [Page 49] RFC 4379 Detecting MPLS Data Plane Failures February 2006

Full Copyright Statement

 Copyright (C) The Internet Society (2006).
 This document is subject to the rights, licenses and restrictions
 contained in BCP 78, and except as set forth therein, the authors
 retain all their rights.
 This document and the information contained herein are provided on an
 "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
 OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
 ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
 INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
 INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
 WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

 The IETF takes no position regarding the validity or scope of any
 Intellectual Property Rights or other rights that might be claimed to
 pertain to the implementation or use of the technology described in
 this document or the extent to which any license under such rights
 might or might not be available; nor does it represent that it has
 made any independent effort to identify any such rights.  Information
 on the procedures with respect to rights in RFC documents can be
 found in BCP 78 and BCP 79.
 Copies of IPR disclosures made to the IETF Secretariat and any
 assurances of licenses to be made available, or the result of an
 attempt made to obtain a general license or permission for the use of
 such proprietary rights by implementers or users of this
 specification can be obtained from the IETF on-line IPR repository at
 http://www.ietf.org/ipr.
 The IETF invites any interested party to bring to its attention any
 copyrights, patents or patent applications, or other proprietary
 rights that may cover technology that may be required to implement
 this standard.  Please address the information to the IETF at
 ietf-ipr@ietf.org.

Acknowledgement

 Funding for the RFC Editor function is provided by the IETF
 Administrative Support Activity (IASA).

Kompella & Swallow Standards Track [Page 50]

/data/webs/external/dokuwiki/data/pages/rfc/rfc4379.txt · Last modified: 2006/02/02 02:05 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki