GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc4356

Network Working Group R. Gellens Request for Comments: 4356 Qualcomm Category: Standards Track January 2006

       Mapping Between the Multimedia Messaging Service (MMS)
                         and Internet Mail

Status of This Memo

 This document specifies an Internet standards track protocol for the
 Internet community, and requests discussion and suggestions for
 improvements.  Please refer to the current edition of the "Internet
 Official Protocol Standards" (STD 1) for the standardization state
 and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

 Copyright (C) The Internet Society (2006).

Abstract

 The cellular telephone industry has defined a service known as the
 Multimedia Messaging Service (MMS).  This service uses formats and
 protocols that are similar to, but differ in key ways from, those
 used in Internet mail.
 One important difference between MMS and Internet Mail is that MMS
 uses headers that start with "X-Mms-" to carry a variety of user
 agent- and server-related information elements.
 This document specifies how to exchange messages between these two
 services, including mapping information elements as used in MMS
 X-Mms-* headers as well as delivery and disposition reports, to and
 from that used in SMTP and Internet message headers.

Gellens Standards Track [Page 1] RFC 4356 Mapping Between MMS and Internet Mail January 2006

Table of Contents

 1. Introduction ....................................................2
    1.1. Scope ......................................................2
    1.2. Conventions Used in This Document ..........................3
    1.3. Definitions ................................................3
    1.4. Abbreviations ..............................................4
    1.5. Assumptions ................................................4
 2. Mapping Between MMS and Internet Mail ...........................4
    2.1. Mapping Specification ......................................5
         2.1.1. MMS to Internet Mail ................................5
         2.1.2. Internet Mail to MMS ................................5
         2.1.3. MMS Information Element Mappings ....................6
         2.1.4. Report Generation and Conversion ...................20
         2.1.5. Message Delivery ...................................27
 3. Security Considerations ........................................27
 4. IANA Considerations ............................................27
 5. Acknowledgements ...............................................27
 6. Normative References ...........................................27
 7. Informative References .........................................29

1. Introduction

1.1. Scope

 This document describes how to exchange messages between Multimedia
 Messaging Service (MMS) systems (as defined by [3GPP][3GPP2][OMA])
 and Internet mail systems (that is, [SMTP] and [Msg-Fmt]).  This
 includes the translation of message formats, message header elements,
 message delivery reports [DSN-Msg], and message disposition reports
 [MDN].
 The MMS architecture [Stage_2] and specifications [Stage_3] refer to
 interfaces as reference points named MMx.  For example, MM1 is the
 client-server interface, MM4 is the server-server interface, and MM3
 is an interface to "external" or non-MMS systems.  The specification
 in this document can be used for message exchange between any system
 that uses Internet message formats and protocols and an MMS system;
 from the perspective of the MMS system, reference point MM3 is used.
 This document includes support for voice messages specified by the
 Voice Profile for Internet Mail [VPIM].  The VPIM specification
 allows voice messages to be exchanged between voice mail systems
 using the Internet mail format [Msg-Fmt] and transported via [SMTP].
 Thus, the MMS MM3 interface supports the ability to exchange voice
 messages between an MMS system and a voice mail system.  Note that
 such use is distinct from voice media being part of a user-composed
 multimedia message.

Gellens Standards Track [Page 2] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Note that MM3 can also be used for interworking with "external"
 (non-MMS) systems other than Internet mail, such as Short Messaging
 Service (SMS) and access to external mail stores (such as a voice
 mail system).  This specification does not address these other uses
 or sub-interfaces of MM3; it is only concerned with Internet mail
 interworking and specifically exchange of messages.
 All MM3 Stage 2 [Stage_2] functions are supported except for reply
 charging and sender address hiding.

1.2. Conventions Used in This Document

 The key words "REQUIRED", "MUST", "MUST NOT", "SHOULD", "SHOULD NOT",
 and "MAY" in this document are to be interpreted as described in "Key
 Words for Use in RFCs to Indicate Requirement Levels" [KEYWORDS].

1.3. Definitions

  1. ——————-|———————————————-

Body |The portion of an [SMTP] message's Content

                     |following the Header (that is, following the
                     |first blank line).  The Body may contain
                     |structured parts and sub-parts, each of which
                     |may have its own Header and Body.  The Body
                     |contains information intended for the message
                     |recipient (human or software).
 --------------------|----------------------------------------------
 Content             |The portion of an SMTP message that is
                     |delivered.  The Content consists of a Header
                     |and a Body.
 --------------------|----------------------------------------------
 Disposition Report  |Feedback information to an originator User
                     |Agent by a recipient User Agent about
 Message Disposition |handling of an original message.  This may
    Notification     |include notification that the message was or
                     |was not read, was deleted unread, etc.
 --------------------|----------------------------------------------
 Envelope            |The portion of an SMTP message not included in
                     |the Content, that is, not in the Header or in
                     |the Body.  While some of it may be copied into
                     |the Content on delivery, envelope information
                     |exists only while the message is in transit,
                     |and contains information used by SMTP agents
                     |(Mail Transfer Agents (MTAs)).
 --------------------|----------------------------------------------
 Gateway             |See [SMTP], Section 2.3.8.
 --------------------|----------------------------------------------

Gellens Standards Track [Page 3] RFC 4356 Mapping Between MMS and Internet Mail January 2006

  1. ——————-|———————————————-

Header |The first part of an SMTP message's Content.

                     |The Header is separated from the Body by a
                     |blank line.  The Header consists of Fields
                     |(such as "To:"), also known as Header Fields
                     |or Headers.  The message Header contains
                     |information used by User Agents.
 --------------------|----------------------------------------------
 Relay/Server        |An MMS server.  See [Stage_2].  For purposes
                     |of this document, an MMS Relay/Server acts as
                     |a gateway when it receives or sends messages
                     |via Internet mail.
 --------------------|----------------------------------------------
 User Agent          |An MMS or email user agent.
 --------------------|----------------------------------------------

1.4. Abbreviations

  1. ——-|———————————————————-

MSA |Message Submission Agent. A server that accepts messages

         |from User Agents and processes them, either delivering
         |them locally or relaying to an MTA.  See [Submission].
 --------|----------------------------------------------------------
 MTA     |Mail Transfer Agent.  A server that implements [SMTP].
 --------|----------------------------------------------------------

1.5. Assumptions

 It is assumed that the reader is already familiar with the contents
 of the 3GPP2 MMS Specification Overview [Overview], MMS Stage 1
 (requirements) [Stage_1] and Stage 2 (architecture and abstract
 messages) [Stage_2], and 3GPP/3GPP2 Stage 3 (protocols) [Stage_3]
 documents.  It is also assumed that the reader is familiar with
 Internet mail, especially RFC 2821 [SMTP] and RFC 2822 [Msg-Fmt].

2. Mapping Between MMS and Internet Mail

 This section defines the interworking between MMS Relay/Servers and
 External Servers using native [SMTP].  That is, information elements
 are exchanged using standard Internet message [Msg-Fmt] header
 fields, such as those in [Hdrs], and standard [SMTP] elements.
 SMTP and Internet mail extensions are used for features such as
 delivery reports, message expiration, and discovery of server support
 for optional features.

Gellens Standards Track [Page 4] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1. Mapping Specification

2.1.1. MMS to Internet Mail

 When sending a message to an Internet mail system, the MMS
 Relay/Server MUST convert the MM if required, and MUST comply with
 the requirements of [SMTP].
 The MMS Relay/Server SHOULD use the information elements associated
 with the MM to define the control information (Internet message
 header fields and SMTP envelope values) needed for the transfer
 protocol.
 Section 2.1.3 lists the mappings between X-Mms-* headers and Internet
 message header fields and SMTP values.
 Delivery and read report MMs SHOULD be converted to standard Internet
 message report format (multipart/report).  In addition to converting
 Internet Message reports, the MMS Relay/Server MUST generate delivery
 and read report MMs for received messages as appropriate.  See
 Section 2.1.4 for more information.

2.1.2. Internet Mail to MMS

 When receiving a message from an Internet mail system, the MMS
 Relay/Server converts incoming messages to the MM format used within
 the receiving system.
 The MMS Relay/Server converts control information received from the
 Internet mail server into appropriate information elements of an MM.
 Section 2.1.3 lists the mappings between X-Mms-* headers and Internet
 message header fields and SMTP values.
 Standard Internet message report format (multipart/report) messages
 MAY be converted to delivery or read report MMs, as appropriate.  In
 addition to converting report MMs, implementations conforming to this
 document MUST generate standard Internet message delivery and
 disposition reports for received Internet messages as appropriate.
 See Section 2.1.4 for more information.

Gellens Standards Track [Page 5] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1.3. MMS Information Element Mappings

 The mappings between MMS elements and SMTP/Internet message elements
 ([SMTP] parameters, [Msg-Fmt] headers, and [DSN-Msg] fields) are
 summarized in table 1 below, and detailed in subsequent sections.
 The "MMS Headers" are from [OMA-MMS].  Note that only information
 elements that need to be mapped are listed. [Msg-Fmt] headers not
 listed here SHOULD be passed unaltered.

2.1.3.1. Table 1: Information Element Mappings

 =================|=================|================|==============
 Information Elem |[SMTP] Element   |[Msg-Fmt] Header|MMS Header
 =================|=================|================|==============
 3GPP MMS Version |N/A              |N/A             |X-Mms-3GPP-MMS
                  |                 |                |   -Version:
 _________________|_________________|________________|______________
 Message Type     |N/A              |N/A             |X-Mms-Message-
 (of PDU)         |                 |                |   Type:
 _________________|_________________|________________|______________
 Transaction ID   |N/A              |N/A             |X-Mms-Transact
                  |                 |                |   ion-Id:
 _________________|_________________|________________|______________
 Message ID       |N/A              |Message-ID:     |Message-ID:
 _________________|_________________|________________|______________
 Recipient        |RCPT TO          |To:, Cc:, or    |To:, Cc:, Bcc:
 address(es)      |address(es)      |omitted (Bcc)   |
 _________________|_________________|________________|______________
 Sender's address |MAIL FROM        |From:           |From:
                  |address if       |                |
                  |user-originated; |                |
                  |MUST set MAIL    |                |
                  |FROM to null     |                |
                  |("<>") for all   |                |
                  |automatically-   |                |
                  |generated MMs    |                |
 _________________|_________________|________________|______________
 Content type     |N/A              |Content-Type:   |Content-type:
                  |                 |                |
                  |                 |For voice mes-  |
                  |                 |sages compliant |
                  |                 |to [VPIM], see  |
                  |                 |Note 2          |
 _________________|_________________|________________|______________

Gellens Standards Track [Page 6] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 =================|=================|================|==============
 Information Elem |[SMTP] Element   |[Msg-Fmt] Header|MMS Header
 =================|=================|================|==============
 Message class    |Class=auto:      |MAY set 'Prece  |X-Mms-Message-
                  |MUST set MAIL    |   dence: bulk' |   Class:
                  |FROM to null     |on class=auto   |
                  |("<>").          |                |
 _________________|_________________|________________|______________
 Date and time    |N/A              |Date:           |Date:
 of submission    |                 |                |
 _________________|_________________|________________|______________
 Time of expiry   |DELIVER-BY       |N/A             |X-Mms-Expiry:
                  |[Deliver-By]     |                |
 _________________|_________________|________________|______________
 Earliest deliv-  |(only for submis-|N/A             |X-Mms-Delivery
 ery time         |sion; not relay) |                |   -Time:
 _________________|_________________|________________|______________
 Delivery report  |DSN [DSN-SMTP]   |N/A             |X-Mms-Delivery
 request          |SHOULD also      |                |   -Report:
                  |specify recip-   |                |
                  |ient address as  |                |
                  |ORCPT; SHOULD    |                |
                  |also specify     |                |
                  |ENVID            |                |
 _________________|_________________|________________|______________
 Importance (a/k/a|N/A              |Importance:     |X-Mms-
 "priority")      |                 |                |   Priority:
                  |                 |                |
                  |                 |                |
 _________________|_________________|________________|______________
 Sender visib-    |(not currently   |(not currently  |X-Mms-Sender-
 ility            |supported)       |supported)      |   Visibility:
 _________________|_________________|________________|______________
 Read reply       |N/A              |Disposition-    |X-Mms-Read-
 request          |                 |   Notification |   Reply:
                  |                 |   -To: [MDN]   |
 _________________|_________________|________________|______________
 Reply-charging   |(not currently   |(not currently  |X-Mms-Reply-
 permission       |supported)       |supported)      |   Charging:
 _________________|_________________|________________|______________
 Reply-charging   |(not currently   |(not currently  |X-Mms-Reply-
 permission       |supported)       |supported)      |   Charging-
 deadline         |                 |                |   Deadline:
 _________________|_________________|________________|______________
 Reply-charging   |(not currently   |(not currently  |X-Mms-Reply-
 permission       |supported)       |supported)      |   Charging-
 limitation       |                 |                |   Size:
 _________________|_________________|________________|______________

Gellens Standards Track [Page 7] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 =================|=================|================|==============
 Information Elem |[SMTP] Element   |[Msg-Fmt] Header|MMS Header
 =================|=================|================|==============
 Reply charging   |(not currently   |(not currently  |X-Mms-Reply-
 usage request    |supported)       |supported)      |   Charging-
                  |                 |                |   Id:
 _________________|_________________|________________|______________
 Reply charging   |(not currently   |(not currently  |X-Mms-Reply-
 usage reference  |supported)       |supported)      |   Charging:
 _________________|_________________|________________|______________
 Subject          |N/A              |Subject:        |Subject:
 _________________|_________________|________________|______________
 Previously-sent  |N/A              |Resent-From:    |X-Mms-Previous
 by               |                 |                |   ly-Sent-By:
 _________________|_________________|________________|______________
 Previously-sent  |N/A              |Resent-Date:    |X-Mms-
 date             |                 |                |   Previously-
                  |                 |                |   Sent-Date-
                  |                 |                |   and-Time:
 _________________|_________________|________________|______________
 Hop/host trace   |N/A              |Received:       |(Not sup-
                  |                 |                |ported)
 _________________|_________________|________________|______________
 Sensitivity      |N/A              |Sensitivity: see|N/A
                  |                 |Note 1          |
 _________________|_________________|________________|______________
 Content          |N/A              |<message body>  |<message body>
 =================|=================|================|==============
 Note 1:  The [VPIM] 'Sensitivity' header element indicates the
 privacy requested by the message originator (values are "personal" or
 "private"); per [VPIM], a message recipient MUST NOT forward a
 message with a 'Sensitivity' header.  Since sensitivity is not an MMS
 feature, any messages that contain a 'Sensitivity:' header SHOULD NOT
 be sent to an MMS system.
 Note 2: [VPIM] specifies how conforming messages are identified.

2.1.3.2. Conversion of Messages from MMS to Internet Format

 3GPP MMS Version
 The 'X-Mms-3GPP-MMS-Version:' header, if present, SHOULD be removed.
 Message Type (of PDU)
 The 'X-Mms-Message-Type:' header, if present, SHOULD be removed.

Gellens Standards Track [Page 8] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Transaction ID
 The 'X-Mms-Transaction-Id:' header, if present, SHOULD be removed.
 Message ID
 The 'Message-Id:' header MUST be retained.  If not present, it MUST
 be created, with a unique value, per [Msg-Fmt].
 To facilitate the case where an MMS message traverses the Internet
 prior to returning to an MMS system, implementations might wish to
 retain the 'X-Mms-Message-Id:' header.  Such systems should be aware
 that headers that begin with "X-" might be removed during transit
 through Internet MTAs.
 Recipient(s) address
 The address of each recipient MUST be transmitted in the [SMTP]
 envelope as a RCPT TO value.  All disclosed recipients SHOULD also
 appear in a 'To:' or 'Cc:' header.  At least one 'To:', 'Cc:', or
 'Bcc:' header MUST be present.  If none are present, a 'To:' header
 SHOULD be created using empty group syntax whose name gives an
 indication to a human reader, for example, 'To:  undisclosed-
 recipients:;'.
 The 'To:' header SHOULD NOT appear more than once.  The 'Cc:' header
 SHOULD NOT appear more than once.
 Each recipient address MUST obey the length restrictions per [SMTP].
 Current Internet Message format requires that only 7-bit US-ASCII
 characters be present in headers.  Non-7-bit characters in an address
 domain must be encoded with [IDN].  If there are any non-7-bit
 characters in the local part of an address, the message MUST be
 rejected.  Non-7-bit characters elsewhere in a header MUST be encoded
 according to [Hdr-Enc].
 All recipient addresses in the [SMTP] envelope must be fully-
 qualified in accordance with [SMTP].  In particular, messages MUST
 NOT be sent to an Internet mail system with an unqualified E.164
 number (i.e., a number with no domain) instead of a fully-qualified
 domain name.
 All addresses in 'To:', 'Cc:', and 'Bcc:' headers MUST be in the form
 of fully-qualified domains.  Unqualified E.164 numbers MUST NOT be
 used.

Gellens Standards Track [Page 9] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Sender address
 The address of the message sender SHOULD appear in the 'From:'
 header.
 The address of the message sender for all user-generated messages
 ('X-Mms-Message-Class:  Personal') SHOULD be transmitted in the
 [SMTP] envelope as the MAIL FROM value.
 The return addresses in the [SMTP] envelope must be fully-qualified
 in accordance with [SMTP].  In particular, messages MUST NOT be sent
 to an Internet mail system with an E.164 number instead of a fully-
 qualified domain name.  Note that qualified E.164 numbers, that is,
 those that contain an E.164 number as the local-part of an address
 that also includes a domain, are acceptable.
 The address(es) in the 'From:' header SHOULD be in the form of
 fully-qualified domains.  Unqualified E.164 numbers SHOULD NOT be
 used.
 Because of the risk of mail loops, it is critical that the MAIL FROM
 be set to null ("<>") for all automatically-generated MMs (such as
 'X-Mms-Message-Class:  Auto').  The MAIL FROM value MUST be set to
 null for all automatically-generated messages.  This includes
 reports, "out-of-office" replies, etc.
 Current Internet message format requires that only 7-bit US-ASCII
 characters be present in headers.  Non-7-bit characters in an address
 domain must be encoded with [IDN].  If there are any Non-7-bit
 characters in the local part of an address, the message MUST be
 rejected.  Non-7-bit characters elsewhere in a header MUST be encoded
 according to [Hdr-Enc].  Note that it would be possible to define an
 [SMTP] extension to permit transmission of unencoded 8-bit
 characters, but in the absence of such an extension [Hdr-Enc] MUST be
 used.
 The sender address MUST obey the length restrictions of [SMTP].
 Content type
 The 'Content-Type:' header SHOULD be preserved.

Gellens Standards Track [Page 10] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Message class
 The 'X-Mms-Message-Class:' header MAY be retained in order to provide
 information on the source of the message.  A 'Precedence:  bulk'
 header MAY be inserted for class=auto or class=advertisement.  See
 'Sender Address' above. (Class=personal and class=informational do
 not require special handling.)
 Time of Expiry
 The 'X-Mms-Expiry:' header, if present, SHOULD be removed.
 The remaining time until the message is considered expired SHOULD be
 transmitted in the [SMTP] envelope by using the DELIVER-BY extension
 with a by-mode of "R", as specified in [Deliver-By].
 Note that the [SMTP] DELIVER-BY extension carries time remaining
 until expiration; each server decrements the value by the amount of
 time it has possessed the message.  The 'X-Mms-Expiry:' header may
 contain either the absolute time at which the message is considered
 expired or the relative time until the message is considered expired.
 Earliest delivery time
 The 'X-Mms-Delivery-Time:' header, if present, SHOULD be removed.
 Future delivery is a message submission (e.g., [Submission]), not
 message relay feature.
 Delivery report request
 Requests for delivery status notifications (DSNs) SHOULD be
 transmitted in the [SMTP] envelope by using the DSN extension as
 specified in [DSN-SMTP] to request "success" or "none" notification
 (depending on the value of the 'X-Mms-Delivery-Report' header).  When
 the NOTIFY extension is used, the unaltered recipient address SHOULD
 be transmitted as the ORCPT value.
 The 'X-Mms-Delivery-Report:' header, if present, SHOULD be removed.
 Importance
 The message sender's importance value (also called "priority",
 although this can be confused with class-of-service values) SHOULD be
 transmitted using an 'Importance:' header.
 Suggested mappings are shown in Table 2:

Gellens Standards Track [Page 11] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1.3.2.1. Table 2: Importance Mappings (MMS to Internet Message)

  1. ————————–|——————

'X-Mms-Priority: High' |'Importance: High'

  1. ————————–|——————

'X-Mms-Priority: Normal' |[omit]

  1. ————————–|——————

'X-Mms-Priority: Low' |'Importance: Low'

  1. ————————–|——————
 Normal importance messages should omit the 'Importance:' header.
 The 'X-Mms-Priority:' header, if present, SHOULD be removed.
 Sender visibility
 Support for sender address hiding is not currently supported.
 A message that contains an 'X-Mms-Sender-Visibility:' header with a
 value of 'Hide' SHOULD be rejected.
 The 'X-Mms-Sender-Visibility:' header, if present, SHOULD be removed.
 Read reply request
 A request for a read reply SHOULD be transmitted using a
 'Disposition-Notification-To:' header as specified in [MDN].
 The 'X-Mms-Read-Reply:' header, if present, SHOULD be removed.
 Reply charging
 Reply charging permission and acceptance are complex issues requiring
 both user agent and server support.  Misapplied reply charging may
 cause incorrect billing.  Until the security issues have been
 properly addressed, reply charging SHOULD NOT be honored when using
 this interface.
 The 'X-Mms-Reply-Charging:', 'X-Mms-Reply-Charging-Deadline:', 'X-
 Mms-Reply-Charging-Size:', and 'X-Mms-Reply-Charging-Id:' headers MAY
 be removed.  Messages containing a reply-charging usage request ('X-
 Mms-Reply-Charging-Id:' and 'X-Mms-Reply-Charging: accepted' or 'X-
 Mms-Reply-Charging: accepted (text only)' headers) SHOULD be
 rejected.

Gellens Standards Track [Page 12] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Subject
 The 'Subject:' header MUST be preserved.  The current Internet
 message format requires that only 7-bit US-ASCII characters be
 present.  Other characters MUST be encoded according to [Hdr-Enc].
 Note that it is possible for an [SMTP] extension to be defined that
 would permit transmission of unencoded 8-bit characters, but in the
 absence of such an extension, [Hdr-Enc] MUST be used.
 Resending
 A message may be resent to one or more new recipients.  It may be
 resent more than once, each time new 'Resent-' headers are added at
 the top of the existing headers.  Thus, if more than one series of
 'Resent-' headers are present, the original series is the last; the
 most recent is the first.
 Forward counter
 An 'X-Mms-Forward-Counter:' header, if present, SHOULD be removed.
 The 'Resent-Count:' header is NOT RECOMMENDED.  Loop control is
 usually done by counting 'Received' headers, which are more general
 than 'Resent-' headers.
 Previously-Sent Information
 MMS lists the resending history of a message in two headers:  'X-
 Mms-Previously-Sent-By:' and 'X-Mms-Previously-Sent-Date-and-Time:'.
 'X-Mms-Previously-Sent-By:'  contains a number followed by one or
 more addresses.  'X-Mms-Previously-Sent-Date-and-Time:' contains a
 number followed by a date-time.  With both headers, the number "0" is
 used for the entry that corresponds to the original submission of the
 message, with higher values being used for each subsequent resending.
 The final (most recent) resending information is in the 'From:' and
 'Date:' headers.  There is also an 'X-Mms-Forward-Counter:' that
 indicates how many times the message has been resent.
 Any 'X-Mms-Previously-Sent-By:', 'X-Mms-Previously-Sent-Date-and-
 Time:', and 'X-Mms-Forward-Counter:'  headers, if present, SHOULD be
 removed.  The information contained in them SHOULD be translated into
 [Msg-Fmt] headers as follows:
 The 'X-Mms-Previously-Sent-Date-and-Time:' header whose value starts
 with "0" SHOULD be used to create a 'Date:' header, converting the
 date and time from HTTP-date [HTTP] to date-time [Msg-Fmt].  The 'X-
 Mms-Previously-Sent-By:' header whose value starts with "0" SHOULD be
 used to create a 'From:' header.

Gellens Standards Track [Page 13] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 A 'To:' header SHOULD be created using list syntax with a value of
 "unrecoverable-recipients" and no mailboxes.
 A 'Message-ID:' header SHOULD be created.
 Any 'X-Mms-Previously-Sent-Date-and-Time:' headers whose value starts
 with "1" or a larger value are mapped to 'Resent-Date:'  headers.
 Any 'X-Mms-Previously-Sent-By:' headers whose value starts with "1"
 or a larger value are mapped to 'Resent-By:' headers.
 The 'From:', 'To:', 'Date:', and 'Message-ID:' headers are mapped to
 'Resent-From:', 'Resent-To:', 'Resent-Date:', and 'Resent-Message-
 ID:' headers in the top-most block of 'Resent-*' headers.
 Example:
 The MMS message:
 X-Mms-Forward-Counter: 2
 X-Mms-Previously-Sent-Date-and-Time: 0, Fri, 01 Apr 2005 06:02:03 GMT
 X-Mms-Previously-Sent-By:   0, General Failure <mfail@example.mil>
 X-Mms-Previously-Sent-Date-and-Time: 1, Fri, 01 Apr 2005 08:02:03 GMT
 X-Mms-Previously-Sent-By:   1, Colonel Corn <gcorn@example.mil>
 Date:               Fri, 1 Apr 2005 18:02:03 -0800
 From:               L. Eva Message <lem@example.org>
 To:                 b1ff@mms.example.com
 Message-ID:         <99887766.112233@mail.example.org>
 is mapped to an Internet mail message:
 Resent-Date: Fri, 1 Apr 2005 18:02:03 -0800
 Resent-From: L. Eva Message <lem@example.org>
 Resent-To:   b1ff@mms.example.com
 Resent-Message-ID:  <99887766.112233@mail.example.org>
 Resent-Date: Fri, 1 Apr 2005 08:02:03 +0000
 Resent-From: Colonel Corn <gcorn@example.mil>
 Date:        Fri, 1 Apr 2005 06:02:03 +0000
 From:        General Failure <mfail@example.mil>
 To:          Colonel Corn <gcorn@example.mil>
 Message-ID:  <000.000.000@gateway.example.org>
 'Received:' Headers
 When a message is gatewayed from MMS to Internet mail, a 'Received:'
 header MUST be added as per [SMTP].  The "with" clause should specify
 "MMS".

Gellens Standards Track [Page 14] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 A message MAY be rejected if the number of 'Received:' headers
 exceeds a locally-defined maximum, which MUST conform to [SMTP]
 Section 6.2 and SHOULD be no less than 100.
 Privacy
 Note that MMS systems do not currently support the 'Privacy' header
 field as described by [VPIM].
 Content
 The message content appears in the message body.  Note that Internet
 message format requires that line endings be encoded as US-ASCII CR
 LF octets; thus, charset encodings that do not have this property
 cannot be used in text/* body parts.  (They may be used in other body
 parts, but only when they are suitably encoded or when binary
 transmission has been negotiated, e.g., [BINARY].)  In particular,
 MMS allows UTF-16, whereas the Internet message format does not.
 UTF-16 encoding MUST be translated to UTF-8 or another charset and
 encoding that is suitable for use in Internet message
 format/protocols.

2.1.3.3. Conversion of Messages from Internet to MMS Format

 3GPP MMS Version
 An 'X-Mms-3GPP-MMS-Version:' header SHOULD be added.
 Message Type (of PDU)
 An 'X-Mms-Message-Type:' header SHOULD be used in accordance with the
 specific MMS interface (e.g., MM1, MM4).
 Transaction ID
 An 'X-Mms-Transaction-Id:' header SHOULD be used in accordance with
 the specific MMS interface (e.g., MM1, MM4).
 Message ID
 The 'Message-Id:' header MUST be retained.  If not present, it MUST
 be created, with a unique value.
 Recipient(s) address
 'To:' and 'Cc:' headers MUST be retained.

Gellens Standards Track [Page 15] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Each recipient contained in the [SMTP] envelope (RCPT TO values) MUST
 be considered a recipient of the message.  Recipients who appear in
 address headers but not the [SMTP] envelope MUST be ignored.
 Recipients who appear in the [SMTP] envelope but do not appear in
 headers are considered "blind" (Bcc) recipients; such recipients MUST
 NOT be added to message headers (including address and trace headers)
 unless there is only one recipient total.
 Sender address
 The 'From:' header MUST be retained.
 Content type
 The complete 'Content-Type:' header (including any parameters) SHOULD
 be preserved.
 Message class
 An 'X-Mms-Message-Class: personal' header MAY be created for all
 received messages with a non-null return path (MAIL FROM value in the
 SMTP envelope).  An 'X-Mms-Message-Class: auto' header MAY be created
 for messages with a null return path.
 Time of Expiry
 An 'X-Mms-Expiry:' header SHOULD be created if the message contains a
 relative time to expiration in the DELIVER-BY extension with a by-
 mode of "R", as specified in [Deliver-By].
 If the by-mode is "N", a "relayed" DSN MUST be issued per
 [Deliver-By] and an 'X-Mms-Expiry:' header SHOULD NOT be created.
 Delivery report request
 An 'X-Mms-Delivery-Report:' header SHOULD be created for messages
 that request 'success' or 'none' delivery status notification by use
 of the DSN extension as specified in [DSN-SMTP].  Requests for
 'delay' notifications or non-default actions, such as that only the
 message headers should be returned, cannot be mapped onto MMS headers
 and thus SHOULD be ignored.

Gellens Standards Track [Page 16] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Importance
 The message sender's importance value (also called "priority",
 although this can be confused with class-of-service values) is
 expressed with an 'Importance:' header.  Historically, some clients
 used the older and non-standard 'X-Priority:' header for this
 purpose.  As a result, some clients generate both.
 An 'X-Priority:' or 'Importance:' header, if present, SHOULD be
 replaced with an 'X-Mms-Priority:' header.  If both headers are
 present, 'Importance:' SHOULD be used.  Suggested mappings are shown
 in Table 3:

2.1.3.3.1. Table 3: Priority Mappings (Internet Message to MMS)

  1. ——————————|———————-

'X-Priority: 1 (highest)' |'X-Mms-Priority: High'

  1. ——————————|———————-

'X-Priority: 2 (high)' |'X-Mms-Priority: High'

  1. ——————————|———————-

'Importance: High' |'X-Mms-Priority: High'

  1. ——————————|———————-

'X-Priority: 3 (normal)' | [omitted]

  1. ——————————|———————-

'Importance: Normal' | [omitted]

  1. ——————————|———————-

'X-Priority: 4 (low)' |'X-Mms-Priority: Low'

  1. ——————————|———————-

'Importance: Low' |'X-Mms-Priority: Low'

  1. ——————————|———————-

'X-Priority: 5 (lowest)' |'X-Mms-Priority: Low'

  1. ——————————|———————-
 Normal importance messages SHOULD omit the 'X-Mms-Priority:' header.
 Sender visibility
 Support for sender address hiding is not currently supported.
 Read reply request
 A request for a read reply contained in a 'Disposition-Notification-
 To:' header as specified in [MDN] SHOULD be replaced with an 'X-Mms-
 Read-Reply:' header.
 Subject
 The 'Subject:' header MUST be preserved.

Gellens Standards Track [Page 17] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Resending
 Mapping from 'Resent-' and other [Msg-Fmt] headers to 'X-Mms-
 Previously-Sent-' headers SHOULD be done as follows:
 The original 'From:' header is mapped to an 'X-Mms-Previously-Sent-
 By:' header with a leading "0" value.  The value of the top-most
 'Resent-From:' header is mapped to the 'From:'  header.  The value of
 each subsequent 'Resent-From:' header is mapped to an 'X-Mms-
 Previously-Sent-By:' header with the next larger leading value.
 The original 'Date:' header is mapped to an 'X-Mms-Previously-Sent-
 Date-and-Time:' header with a leading "0" value.  Note that the value
 is also converted from date-time syntax [Msg-Fmt] to HTTP-date syntax
 [HTTP].  The value of the top-most 'Resent-Date:' header is mapped to
 the 'Date:' header.  The value of each subsequent 'Date:' header is
 mapped to an 'X-Mms-Previously-Sent-Date-and-Time:' header with the
 next larger leading value.
 If one or more 'Resent-Message-ID:' headers are present, the top-most
 one SHOULD be mapped to 'Message-ID:'; otherwise, the 'Message-ID:'
 header should be retained.
 An 'X-Mms-Forward-Counter:' header SHOULD be created when 'Resent-'
 headers have been mapped to 'X-Mms-Previously-Sent-' headers.  Its
 value SHOULD be the number of 'Resent-' blocks that existed prior to
 mapping.
 Example:
 The original message:
 Date:        Fri, 1 Apr 2005 14:02:03 -0800
 From:        General Failure <mfail@example.mil>
 To:          Colonel Corn <gcorn@example.mil>
 Message-ID:  <msg123@mail.example.mil>
 Is resent by Colonel Corn to L. Eva Message:
 Resent-Date: Fri, 1 Apr 2005 16:02:03 -0800
 Resent-From: Colonel Corn <gcorn@example.mil>
 Resent-To:   L. Eva Message <lem@example.org>
 Resent-Message-ID:  <msg234@mail.example.mil>
 Date:        Fri, 1 Apr 2005 14:02:03 -0800
 From:        General Failure <mfail@example.mil>
 To:          Colonel Corn <gcorn@example.mil>
 Message-ID:  <msg123@mail.example.mil>

Gellens Standards Track [Page 18] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 L. Eva then resends to her MMS device:
 Resent-Date: Fri, 1 Apr 2005 18:02:03 -0800
 Resent-From: L. Eva Message <lem@example.org>
 Resent-To:   b1ff@mms.example.com
 Resent-Message-ID:  <99887766.112233@mail.example.org>
 Resent-Date: Fri, 1 Apr 2005 16:02:03 -0800
 Resent-From: Colonel Corn <gcorn@example.mil>
 Resent-To:   L. Eva Message <lem@example.org>
 Resent-Message-ID:  <msg234@mail.example.mil>
 Date:        Fri, 1 Apr 2005 14:02:03 -0800
 From:        General Failure <mfail@example.mil>
 To:          Colonel Corn <gcorn@example.mil>
 Message-ID:  <msg123@mail.example.mil>
 This would be mapped to an MMS message as:
 X-Mms-Forward-Counter: 2
 X-Mms-Previously-Sent-Date-and-Time: 0, Fri, 01 Apr 2005 06:02:03 GMT
 X-Mms-Previously-Sent-By:   0, General Failure <mfail@example.mil>
 X-Mms-Previously-Sent-Date-and-Time: 1, Fri, 01 Apr 2005 08:02:03 GMT
 X-Mms-Previously-Sent-By:   1, Colonel Corn <gcorn@example.mil>
 Date:               Fri, 1 Apr 2005 18:02:03 -0800
 From:               L. Eva Message <lem@example.org>
 To:                 b1ff@mms.example.com
 Message-ID:         <99887766.112233@mail.example.org>
 Note that the original 'From:' and 'Date:' values were moved to 'X-
 Mms-Previously-Sent-By:' and 'X-Mms-Previously-Sent-Date-and-Time:'
 headers with a leading "0" value.  The first 'Resent-From:' and
 'Resent-Date:' values were moved to a second set of 'X-Mms-
 Previously-Sent-' headers, with a leading "1" value.  The third set
 of 'Resent-' headers were moved to the 'Date:', 'To:', and 'From:'
 headers.
 Note also that the format of the date and time differs between the
 'Date:' / 'Resent-Date:' and the 'X-Mms-Previously-Sent-Date-and-
 Time:' headers, in that the latter use HTTP-date [HTTP] instead of
 date-time [Msg-Fmt].
 'Received:' Headers
 Each system that processes a message SHOULD add a 'Received:' header
 as per [SMTP].  A message MAY be rejected if the number of
 'Received:' headers exceeds a locally-defined maximum, which MUST
 conform to [SMTP] Section 6.2 and SHOULD be no less than 100.

Gellens Standards Track [Page 19] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 Sensitivity
 The 'Sensitivity:' header field (value = "personal" or "private")
 [VPIM] indicates the desire of a voice message originator to send the
 message contents to the original recipient list with assurance that
 the message will not be forwarded further by either the messaging
 system or the actual message recipient(s).  Since sensitivity is not
 an MMS feature, any messages that contain a 'Sensitivity:' header
 MUST NOT be sent to an MMS system.  The associated negative delivery
 status report MUST include the extended status code [RESP] 5.6.0 as
 specified in [VPIM] ("Other or undefined protocol status") indicating
 that privacy could not be ensured.
 Content
 The message content appears in the message body.

2.1.4. Report Generation and Conversion

 Internet message systems use the multipart/report MIME type for
 delivery and disposition reports as specified in [Report-Fmt].  This
 format is a two- or three-part MIME message; one part is a structured
 format describing the event being reported in an easy-to-parse
 format.  Specific reports have a format that is built on
 [Report-Fmt].  Delivery reports are specified in [DSN-Msg].  Message
 disposition reports, which include read reports, are specified in
 [MDN].
 By contrast, MMS reports are plain text, with no defined structure
 specified.  This makes it difficult to convert from an MMS report to
 a standard Internet report.
 An implementation conforming to this specification MUST convert
 reports received from one side (MMS or Internet mail) destined for
 the other.  In addition, reports MUST be generated as appropriate for
 messages received from either side.  For example, if an MM to be sent
 via Internet mail is not deliverable, a delivery status MM shall be
 generated.  Likewise, if an Internet message is received that cannot
 be further relayed or delivered, a delivery status report [DSN-Msg]
 MUST be generated.
 When creating delivery or disposition reports from MMS reports, the
 MMS report should be parsed to determine the reported event and time,
 status, and the headers of the referenced (original) message.  These
 elements, once determined, are used to populate the subparts of the
 delivery or disposition report.  The first subpart is of type
 text/plain, and contains a human-readable explanation of the event.
 This text may include a statement that the report was synthesized

Gellens Standards Track [Page 20] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 based on an MMS report.  The second subpart is of type
 report/delivery-status (for delivery reports) or report/disposition-
 notification (for disposition reports).  This second part contains a
 structured itemization of the event.  The optional third subpart is
 of type message/rfc822 and includes the headers and optionally the
 body of the referenced (original) message.  Note that, per [DSN-Msg],
 the 'DSN-Gateway:' field in delivery reports MUST be created.

2.1.4.1. Delivery Report Mapping from MMS to Internet Message

 Below, Table 4 maps information elements from MMS delivery reports to
 the format specified in [DSN-Msg].

2.1.4.1.1. Table 4: Delivery Report Mappings (MMS to Internet Message)

|============|

Information Element |MMS Delivery|[DSN-Msg] Element

                    |Report Elem |

|============|

ID of message whose |Message-Id: |'Message-ID:' preserved in third delivery status is | |subpart of delivery report. being reported | | ———————-|————|———————————– Recipient address of |From: |'Final-Recipient' field of the the original message | |per-recipient section. (object of delivery | | report) | | ———————-|————|———————————– Destination address of|To: |'To:' header field value of top- report | |level. ———————-|————|———————————– Date and time the |Date: |'Date:' header field value of top- message was handled | |level. ———————-|————|———————————–

Gellens Standards Track [Page 21] RFC 4356 Mapping Between MMS and Internet Mail January 2006

|============|

Information Element |MMS Delivery|[DSN-Msg] Element

                    |Report Elem |

|============|

Delivery status of |X-Mms- |Action and Status fields of original message to | Status: |per-recipient section. each recipient | |

                    |            |The 'Action' field indicates if the
                    |            |message was delivered.
                    |            |
                    |            |For failed delivery, an appropriate
                    |            |'Status' value shall be included
                    |            |per [DSN-Msg].
                    |            |
                    |            |The Action field is set to one of
                    |            |the following values:
                    |            |
                    |            |* delivered (used for MMS status
                    |            |values 'retrieved' and 'rejected',
                    |            |depending on 'Status' code).
                    |            |
                    |            |* failed (used for MMS status
                    |            |values 'expired' and 'unreachable')
                    |            |
                    |            |* delayed MAY be used for MMS
                    |            |status value 'deferred'
                    |            |
                    |            |* relayed (used for MMS status
                    |            |value 'indeterminate')
                    |            |
                    |            |* expanded (SHOULD NOT be used)

———————-|————|———————————– Status Text | |Text in first part (human-readable

                    |            |part).

———————-|————|———————————–

 When an MMS Relay/Server generates a [DSN-Msg] in response to a
 message received using [SMTP] on MM3:
  • Top-level header field 'To:' SHOULD be the [SMTP] return-path of

the message whose status is being reported.

  • Top-level header field 'From:' SHOULD be the address of the

recipient that the delivery-report concerns.

  • The first part of the [DSN-Msg] SHOULD include the MM Status Text

field that would have been generated for an MM1 delivery-report.

Gellens Standards Track [Page 22] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1.4.2 Delivery Report Mapping from Internet Message to MMS

 Below, Table 5 maps information elements from a delivery report as
 specified in [DSN-Msg] to the format of an MMS delivery report.  Note
 that a single DSN that reports multiple recipients will result in
 several MMS delivery reports.

2.1.4.2.1. Table 5: Delivery Report Mappings (Internet Message to MMS)

|==================|

Information Element|MMS Delivery |[DSN-Msg] Element

                 |Report Element    |

|==================|

ID of the original |Message-Id: |'Message-ID:' header preserved message (object of | |in third sub-part of report. delivery report) | | ——————-|——————|——————————– Recipient address |From: |If available, the 'Original of the original | |-Recipient' field of the per- message (object of | |recipient section should be delivery report) | |used; otherwise, the 'Final-

                 |                  |Recipient' field of the per-
                 |                  |recipient section is used.

——————-|——————|——————————– Destination address|To: |'To:' header field value of of report | |top-level.

                 |                  |
                 |                  |Value taken from [SMTP] envelope
                 |                  |return-path of message being
                 |                  |reported, not its 'From:' header
                 |                  |field.

——————-|——————|——————————– Date and time the |Date: |'Date:' header field value of message was handled| |top-level. ——————-|——————|——————————–

Gellens Standards Track [Page 23] RFC 4356 Mapping Between MMS and Internet Mail January 2006

|==================|

Information Element|MMS Delivery |[DSN-Msg] Element

                 |Report Element    |

|==================|

Delivery status of |X-Mms-Status: |'Action' and 'Status' fields of original message | |per-recipient section.

                 |Set to one of the |
                 |following values: |
                 |                  |
                 |'retrieved' (used |
                 |for 'Action' value|
                 |'delivered').     |
                 |                  |
                 |'unreachable'     |
                 |(used for 'Action'|
                 |value 'failed')   |
                 |                  |
                 |'forwarded' (used |
                 |for 'Action' value|
                 |'relayed')        |
                 |                  |
                 |'deferred' MUST   |
                 |NOT be used       |
                 |(ignore DSNs with |
                 |'Action' value    |
                 |'delayed')        |

——————-|——————|——————————– Status Text | |Text in first part (human-

                 |                  |readable part).

|==================|

2.1.4.3. Read Report Mapping from MMS to Internet Message

 Below, Table 6 maps information elements from MMS read reports to the
 format specified in [MDN].

2.1.4.3.1. Table 6: Read Report Mappings (MMS to Internet Message)

|============|

Information Element |MMS Delivery|[MDN] Element

                    |Report Elem |

|============|

ID of the original |Message-Id: |'Message-ID:' header preserved in message (object of | |third part of report. read report) | | ———————-|————|———————————– Recipient address of |From: |'Final-Recipient' field. the original message | |

Gellens Standards Track [Page 24] RFC 4356 Mapping Between MMS and Internet Mail January 2006

|============|

Information Element |MMS Delivery|[MDN] Element

                    |Report Elem |

|============|

Destination address of|To: |'To:' header field value of top- report | |level.

                    |            |
                    |            |Value taken from 'Disposition-
                    |            |Notification-To:' header field of
                    |            |message being reported, not its
                    |            |'From:' header field.

———————-|————|———————————– Date and time the |Date: |'Date:' header field value of top- message was handled | |level. ———————-|————|———————————– Disposition of message|X-Mms-Read- |Disposition-field being reported | Status: |

                    |            |For X-MMS-Read-Status value 'read',
                    |            |use 'disposition-type' value
                    |            |'displayed'; for X-MMS-Read-Status
                    |            |value 'Deleted without being read',
                    |            |use 'disposition-type' value
                    |            |'deleted').

———————-|————|———————————– Status Text | |Text in first part (human-readable

                    |            |part).

|============|

 When an MMS Relay/Server generates an [MDN] in response to a message
 received using [SMTP] on MM3:
  • Top-level header field 'To:' SHOULD be the value of the

'Disposition-Notification-To:' header field of the message whose

   disposition is being reported.
  • Top-level header field 'From:' SHOULD be the address of the

recipient that the read report concerns.

2.1.4.4. Disposition Report Mapping from Internet Message to MMS

 Below, Table 7 maps information elements from a disposition report as
 specified in [MDN] to the format of an MMS read report.

Gellens Standards Track [Page 25] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1.4.4.1. Table 7: Disposition Report Mappings

                    (Internet Message to MMS)

|==================|

Information Element|MMS Read Report |[MDN] Element

                 |Element           |

|==================|

ID of the original |Message-Id: |'Message-ID:' header preserved message (object of | |in third subpart of report. disposition report)| | ——————-|——————|——————————– Recipient address |From: |'Final-Recipient' field. of the original | | message | | ——————-|——————|——————————– Destination address|To: |'To:' header field value of of report | |top-level.

                 |                  |
                 |                  |Value taken from 'Disposition-
                 |                  |Notification-To:' header field
                 |                  |of message being reported, not
                 |                  |its 'From:' header field.

——————-|——————|——————————– Date and time the |Date: |'Date:' header field value of message was handled| |top-level. ——————-|——————|——————————– Disposition of |X-Mms-Read-Status:|disposition-field. message being | | reported |Set to one of the |

                 |following values: |
                 |                  |
                 |'read' (used for  |
                 |disposition-type  |
                 |value 'displayed')|
                 |                  |
                 |'Deleted without  |
                 |being read' (used |
                 |for disposition-  |
                 |types 'deleted',  |
                 |'denied' and      |
                 |'failed' when     |
                 |action-mode is    |
                 |'automatic-       |
                 |action')          |

——————-|——————|——————————– Status Text | |Text in first part (human-

                 |                  |readable part).

|==================|

Gellens Standards Track [Page 26] RFC 4356 Mapping Between MMS and Internet Mail January 2006

2.1.5. Message Delivery

 Within Internet mail, when [SMTP] is used and delivery reports are
 requested [DSN-SMTP], delivery is considered to be acceptance of a
 message by the final server, that is, the server closest to the
 recipient.  When an MMS Relay/Server receives a message using [SMTP]
 and a delivery report is requested, the MMS Relay/Server MAY consider
 the message delivered when it has been sent to the MMS User Agent.

3. Security Considerations

 Both MMS and Internet mail have their own set of security risks and
 considerations.  This document specifies how to exchange messages
 between these two environments, so it is only appropriate to discuss
 considerations specific to this functionality, not those inherent in
 either environment.
 When a message uses end-to-end security mechanisms such as [PGP] or
 S/MIME [SMIME], servers MUST be careful not to accidently destroy the
 integrity of the protected content (for example, by altering any text
 within the region covered by a signature while mapping between MMS
 and email).  [Mime-Sec-gw] discusses issues with use of such
 mechanisms in gateways.
 Some MMS features contain inherently more risk than others, including
 reply charging and sender address hiding.  Support for these
 mechanisms is not included in this document.

4. IANA Considerations

 IANA has added "MMS" as one of the "WITH protocol types" under its
 "MAIL Parameters" registry.  The description is "Multimedia Messaging
 Service"; the reference is to this document.

5. Acknowledgements

 A number of people contributed to this document, especially the
 members of the IETF Lemonade working group, including Greg Vaudreuil.
 John Klensin did a very thorough and helpful review.  Greg White
 caught a large number of nits.  Ted Hardie was very helpful.  Alexey
 Melnikov and Chris Newman sent very useful and detailed comments.

6. Normative References

 [DSN-Msg]     Moore, K. and G. Vaudreuil, "An Extensible Message
               Format for Delivery Status Notifications", RFC 3464,
               January 2003.

Gellens Standards Track [Page 27] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 [DSN-SMTP]    Moore, K., "Simple Mail Transfer Protocol (SMTP)
               Service Extension for Delivery Status Notifications
               (DSNs)", RFC 3461, January 2003.
 [Hdr-Enc]     Moore, K., "MIME (Multipurpose Internet Mail
               Extensions) Part Three: Message Header Extensions for
               Non-ASCII Text ", RFC 2047, November 1996.
 [HTTP]        Fielding,  R., Gettys, J., Mogul, J., Frystyk, H.,
               Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext
               Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999.
 [IDN]         Faltstrom, P., Hoffman, P., and A. Costello,
               "Internationalizing Domain Names in Applications
               (IDNA)", RFC 3490, March 2003.
 [KEYWORDS]    Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.
 [MDN]         Hansen, T. and G. Vaudreuil, "Message Disposition
               Notification", RFC 3798, May 2004.
 [Msg-Fmt]     Resnick, P., "Internet Message Format", RFC 2822, April
               2001.
 [Report-Fmt]  Vaudreuil, G., "The Multipart/Report Content Type for
               the Reporting of Mail System Administrative Messages",
               RFC 3462, January 2003.
 [RESP]        Vaudreuil, G., "Enhanced Mail System Status Codes", RFC
               3463, January 2003.
 [SMTP]        Klensin, J., "Simple Mail Transfer Protocol", RFC 2821,
               April 2001.
 [OMA]         OMA specifications are available at the OMA web site
               <http://www.openmobilealliance.org>.
 [OMA-MMS]     OMA-WAP-MMS-ENC-V1_2-20040323-C
 [3GPP2]       3GPP2 specifications are available at the 3GPP2 (Third
               Generation Partnership Project 2) web site
               <http://www.3gpp2.org>.
 [3GPP]        3GPP specifications are available at the 3GPP (Third
               Generation Partnership Project) web site
               <http://www.3gpp.org>

Gellens Standards Track [Page 28] RFC 4356 Mapping Between MMS and Internet Mail January 2006

 [Stage_3]     "MMS MM1 Stage 3 using OMA/WAP", X.S0016-310
               "MMS MM4 Stage 3 Inter-Carrier Interworking", X.S0016-
               340
               "Multimedia Messaging Service:  Functional description;
               Stage 2", TS 23.140 Release 5.

7. Informative References

 [BINARY]      Vaudreuil, G., "SMTP Service Extensions for
               Transmission of Large and Binary MIME Messages", RFC
               3030, December 2000.
 [Deliver-By]  Newman, D., "Deliver By SMTP Service Extension", RFC
               2852, June 2000.
 [Hdrs]        Palme, J., "Common Internet Message Headers", RFC 2076,
               February 1997.
 [Mime-Sec-gw] Freed, N., "Gateways and MIME Security Multiparts", RFC
               2480, January 1999.
 [PGP]         Elkins, M., Del Torto, D., Levien, R., and T. Roessler,
               "MIME Security with OpenPGP", RFC 3156, August 2001.
 [SMIME]       Ramsdell, B., "Secure/Multipurpose Internet Mail
               Extensions (S/MIME) Version 3.1 Message Specification",
               RFC 3851, July 2004.
 [Submission]  Gellens, R. and J. Klensin, "Message Submission", RFC
               2476, December 1998.
 [VPIM]        Vaudreuil, G. and G. Parsons, "Voice Profile for
               Internet Mail - version 2 (VPIMv2)", RFC 3801, June
               2004.
 [Overview]    "Multimedia Messaging Services (MMS) Overview",
               X.S0016-000
 [Stage_1]     "Multimedia Messaging Services (MMS); Stage 1",
               Requirements, October 2002, S.R0064-0.
 [Stage_2]     "Multimedia Messaging Service (MMS); Stage 2",
               Functional Specification, April 2003, X.S0016-200.
               "Multimedia Messaging Service; Media formats and
               codecs", TS26.140Release 5.

Gellens Standards Track [Page 29] RFC 4356 Mapping Between MMS and Internet Mail January 2006

Author's Address

 Randall Gellens
 QUALCOMM Incorporated
 5775 Morehouse Drive
 San Diego, CA  92121
 EMail: randy@qualcomm.com

Gellens Standards Track [Page 30] RFC 4356 Mapping Between MMS and Internet Mail January 2006

Full Copyright Statement

 Copyright (C) The Internet Society (2006).
 This document is subject to the rights, licenses and restrictions
 contained in BCP 78, and except as set forth therein, the authors
 retain all their rights.
 This document and the information contained herein are provided on an
 "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
 OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
 ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
 INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
 INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
 WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

 The IETF takes no position regarding the validity or scope of any
 Intellectual Property Rights or other rights that might be claimed to
 pertain to the implementation or use of the technology described in
 this document or the extent to which any license under such rights
 might or might not be available; nor does it represent that it has
 made any independent effort to identify any such rights.  Information
 on the procedures with respect to rights in RFC documents can be
 found in BCP 78 and BCP 79.
 Copies of IPR disclosures made to the IETF Secretariat and any
 assurances of licenses to be made available, or the result of an
 attempt made to obtain a general license or permission for the use of
 such proprietary rights by implementers or users of this
 specification can be obtained from the IETF on-line IPR repository at
 http://www.ietf.org/ipr.
 The IETF invites any interested party to bring to its attention any
 copyrights, patents or patent applications, or other proprietary
 rights that may cover technology that may be required to implement
 this standard.  Please address the information to the IETF at
 ietf-ipr@ietf.org.

Acknowledgement

 Funding for the RFC Editor function is provided by the IETF
 Administrative Support Activity (IASA).

Gellens Standards Track [Page 31]

/data/webs/external/dokuwiki/data/pages/rfc/rfc4356.txt · Last modified: 2006/01/10 22:15 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki