GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc3890

Network Working Group M. Westerlund Request for Comments: 3890 Ericsson Category: Standards Track September 2004

            A Transport Independent Bandwidth Modifier
             for the Session Description Protocol (SDP)

Status of this Memo

 This document specifies an Internet standards track protocol for the
 Internet community, and requests discussion and suggestions for
 improvements.  Please refer to the current edition of the "Internet
 Official Protocol Standards" (STD 1) for the standardization state
 and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

 Copyright (C) The Internet Society (2004).

Abstract

 This document defines a Session Description Protocol (SDP) Transport
 Independent Application Specific Maximum (TIAS) bandwidth modifier
 that does not include transport overhead; instead an additional
 packet rate attribute is defined.  The transport independent bit-rate
 value together with the maximum packet rate can then be used to
 calculate the real bit-rate over the transport actually used.
 The existing SDP bandwidth modifiers and their values include the
 bandwidth needed for the transport and IP layers.  When using SDP
 with protocols like the Session Announcement Protocol (SAP), the
 Session Initiation Protocol (SIP), and the Real-Time Streaming
 Protocol (RTSP), and when the involved hosts has different transport
 overhead, for example due to different IP versions, the
 interpretation of what lower layer bandwidths are included is not
 clear.

Westerlund Standards Track [Page 1] RFC 3890 Bandwidth Modifier for SDP September 2004

Table of Contents

 1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  The Bandwidth Attribute. . . . . . . . . . . . . . . . .  3
           1.1.1.  Conference Total . . . . . . . . . . . . . . . .  3
           1.1.2.  Application Specific Maximum . . . . . . . . . .  3
           1.1.3.  RTCP Report Bandwidth. . . . . . . . . . . . . .  4
     1.2.  IPv6 and IPv4. . . . . . . . . . . . . . . . . . . . . .  4
     1.3.  Further Mechanisms that Change the Bandwidth
           Utilization. . . . . . . . . . . . . . . . . . . . . . .  5
           1.3.1.  IPsec. . . . . . . . . . . . . . . . . . . . . .  5
           1.3.2.  Header Compression . . . . . . . . . . . . . . .  5
 2.  Definitions. . . . . . . . . . . . . . . . . . . . . . . . . .  6
     2.1.  Glossary . . . . . . . . . . . . . . . . . . . . . . . .  6
     2.2.  Terminology. . . . . . . . . . . . . . . . . . . . . . .  6
 3.  The Bandwidth Signaling Problems . . . . . . . . . . . . . . .  6
     3.1.  What IP Version is Used. . . . . . . . . . . . . . . . .  6
     3.2.  Taking Other Mechanisms into Account . . . . . . . . . .  7
     3.3.  Converting Bandwidth Values. . . . . . . . . . . . . . .  8
     3.4.  RTCP Problems. . . . . . . . . . . . . . . . . . . . . .  8
     3.5.  Future Development . . . . . . . . . . . . . . . . . . .  9
     3.6.  Problem Conclusion . . . . . . . . . . . . . . . . . . .  9
 4.  Problem Scope. . . . . . . . . . . . . . . . . . . . . . . . . 10
 5.  Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 10
 6.  Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
     6.1.  Introduction . . . . . . . . . . . . . . . . . . . . . . 11
     6.2.  The TIAS Bandwidth Modifier. . . . . . . . . . . . . . . 11
           6.2.1.  Usage. . . . . . . . . . . . . . . . . . . . . . 11
           6.2.2.  Definition . . . . . . . . . . . . . . . . . . . 12
           6.2.3.  Usage Rules. . . . . . . . . . . . . . . . . . . 13
     6.3.  Packet Rate Parameter. . . . . . . . . . . . . . . . . . 13
     6.4.  Converting to Transport-Dependent Values . . . . . . . . 14
     6.5.  Deriving RTCP bandwidth. . . . . . . . . . . . . . . . . 15
           6.5.1. Motivation for this Solution. . . . . . . . . . . 15
     6.6.  ABNF Definitions . . . . . . . . . . . . . . . . . . . . 16
     6.7.  Example. . . . . . . . . . . . . . . . . . . . . . . . . 16
 7.  Protocol Interaction . . . . . . . . . . . . . . . . . . . . . 17
     7.1.  RTSP . . . . . . . . . . . . . . . . . . . . . . . . . . 17
     7.2.  SIP. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
     7.3.  SAP. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
 8.  Security Considerations. . . . . . . . . . . . . . . . . . . . 18
 9.  IANA Considerations. . . . . . . . . . . . . . . . . . . . . . 18
 10. Acknowledgments. . . . . . . . . . . . . . . . . . . . . . . . 19
 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19
     11.1. Normative References . . . . . . . . . . . . . . . . . . 19
     11.2. Informative References . . . . . . . . . . . . . . . . . 19
 12. Author's Address . . . . . . . . . . . . . . . . . . . . . . . 21
 13. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 22

Westerlund Standards Track [Page 2] RFC 3890 Bandwidth Modifier for SDP September 2004

1. Introduction

 This specification is structured in the following way: In this
 section, some information regarding SDP bandwidth modifiers, and
 different mechanisms that affect transport overhead are asserted.  In
 section 3, the problems found are described, including problems that
 are not solved by this specification.  In section 4 the scope of the
 problems this specification solves is presented.  Section 5 contains
 the requirements applicable to the problem scope.  Section 6 defines
 the solution, which is a new bandwidth modifier, and a new maximum
 packet rate attribute.  Section 7 looks at the protocol interaction
 for SIP, RTSP, and SAP.  The security considerations are discussed in
 section 8.  The remaining sections are the necessary IANA
 considerations, acknowledgements, reference list, author's address,
 and copyright and IPR notices.
 Today the Session Description Protocol (SDP) [1] is used in several
 types of applications.  The original application is session
 information and configuration for multicast sessions announced with
 Session Announcement Protocol (SAP) [5].  SDP is also a vital
 component in media negotiation for the Session Initiation Protocol
 (SIP) [6] by using the offer answer model [7].  The Real-Time
 Streaming Protocol (RTSP) [8] also makes use of SDP to declare to the
 client what media and codec(s) comprise a multi-media presentation.

1.1. The Bandwidth Attribute

 In SDP [1] there exists a bandwidth attribute, which has a modifier
 used to specify what type of bit-rate the value refers to.  The
 attribute has the following form:
    b=<modifier>:<value>
 Today there are four defined modifiers used for different purposes.

1.1.1. Conference Total

 The Conference Total is indicated by giving the modifier "CT".
 Conference total gives a maximum bandwidth that a conference session
 will use.  Its purpose is to decide if this session can co-exist with
 any other sessions, defined in RFC 2327 [1].

1.1.2. Application Specific Maximum

 The Application Specific maximum bandwidth is indicated by the
 modifier "AS".  The interpretation of this attribute is dependent on
 the application's notion of maximum bandwidth.  For an RTP
 application, this attribute is the RTP session bandwidth as defined

Westerlund Standards Track [Page 3] RFC 3890 Bandwidth Modifier for SDP September 2004

 in RFC 3550 [4].  The session bandwidth includes the bandwidth that
 the RTP data traffic will consume, including the lower layers, down
 to the IP layer.  Therefore, the bandwidth is in most cases
 calculated over RTP payload, RTP header, UDP, and IP, defined in RFC
 2327 [1].

1.1.3. RTCP Report Bandwidth

 In RFC 3556 [9], two bandwidth modifiers are defined.  These
 modifiers, "RS" and "RR", define the amount of bandwidth that is
 assigned for RTCP reports by active data senders and RTCP reports by
 other participants (receivers), respectively.

1.2. IPv6 and IPv4

 Today there are two IP versions, 4 [14] and 6 [13], used in parallel
 on the Internet, creating problems.  However, there exist a number of
 possible transition mechanisms.
  1. The nodes which wish to communicate must share the IP version;

typically this is done by deploying dual-stack nodes. For

    example, an IPv4 only host cannot communicate with an IPv6 only
    host.
  1. If communication between nodes which do not share a protocol

version is required, use of a translation or proxying mechanism

    would be required.  Work is underway to specify such a mechanism
    for this purpose.
  1. —————– ———————-

| IPv4 domain | | IPv6 Domain |

    |                | ------------- |                    |
    | ----------     |-|Translator |-|      ----------    |
    | |Server A|     | | or proxy  | |      |Client B|    |
    | ----------     | ------------- |      ----------    |
    ------------------               ----------------------
    Figure 1. Translation or proxying between IPv6 and IPv4 addresses.
  1. IPv6 nodes belonging to different domains running IPv6, but

lacking IPv6 connectivity between them, solve this by tunneling

    over the IPv4 net, see Figure 2.  Basically, the IPv6 packets are
    sent as payload in IPv4 packets between the tunneling end-points
    at the edge of each IPv6 domain.  The bandwidth required over the
    IPv4 domain will be different from IPv6 domains.  However, as the
    tunneling is normally not performed by the application end-point,
    this scenario can not usually be taken into consideration.

Westerlund Standards Track [Page 4] RFC 3890 Bandwidth Modifier for SDP September 2004

  1. ————– ————— —————

| IPv6 domain | | IPv4 domain | | IPv6 Domain |

    |             |  |-------------|  |             |
    | ----------  |--||Tunnel     ||--| ----------  |
    | |Server A|  |  |-------------|  | |Client B|  |
    | ----------  |  |             |  | ----------  |
    ---------------  ---------------  --------------|
    Figure 2. Tunneling through a IPv4 domain
 IPv4 has a minimum header size of 20 bytes, while the fixed part of
 the IPv6 header is 40 bytes.
 The difference in header sizes means that the bit-rate required for
 the two IP versions is different.  The significance of the difference
 depends on the packet rate and payload size of each packet.

1.3. Further Mechanisms that Change the Bandwidth Utilization

 There exist a number of other mechanisms that also may change the
 overhead at layers below media transport.  We will briefly cover a
 few of these here.

1.3.1. IPsec

 IPsec [19] can be used between end points to provide confidentiality
 through the application of the IP Encapsulating Security Payload
 (ESP) [21] or integrity protection using the IP Authentication Header
 (AH) [20] of the media stream.  The addition of the ESP and AH
 headers increases each packet's size.
 To provide virtual private networks, complete IP packets may be
 encapsulated between an end node and the private networks security
 gateway, thus providing a secure tunnel that ensures confidentiality,
 integrity, and authentication of the packet stream.  In this case,
 the extra IP and ESP header will significantly increase the packet
 size.

1.3.2. Header Compression

 Another mechanism that alters the actual overhead over links is
 header compression.  Header compression uses the fact that most
 network protocol headers have either static or predictable values in
 their fields within a packet stream.  Compression is normally only
 done on a per hop basis, i.e., on a single link.  The normal reason
 for doing header compression is that the link has fairly limited
 bandwidth and significant gain in throughput is achieved.

Westerlund Standards Track [Page 5] RFC 3890 Bandwidth Modifier for SDP September 2004

 There exist several different header compression standards.  For
 compressing IP headers only, there is RFC 2507 [10].  For compressing
 packets with IP/UDP/RTP headers, CRTP [11] was created at the same
 time.  More recently, the Robust Header Compression (ROHC) working
 group has been developing a framework and profiles [12] for
 compressing certain combinations of protocols, like IP/UDP, and
 IP/UDP/RTP.

2. Definitions

2.1. Glossary

 ALG  - Application Level Gateway.
 bps  - bits per second.
 RTSP - Real-Time Streaming Protocol, see [8].
 SDP  - Session Description Protocol, see [1].
 SAP  - Session Announcement Protocol, see [5].
 SIP  - Session Initiation Protocol, see [6].
 TIAS - Transport Independent Application Specific maximum, a
        bandwidth modifier.

2.2. Terminology

 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
 "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
 document are to be interpreted as described in BCP 14, RFC 2119 [3].

3. The Bandwidth Signaling Problems

 When an application wants to use SDP to signal the bandwidth required
 for this application, some problems become evident due to the
 inclusion of the lower layers in the bandwidth values.

3.1. What IP Version is Used

 If one signals the bandwidth in SDP, for example, using "b=AS:" as an
 RTP based application, one cannot know if the overhead is calculated
 for IPv4 or IPv6.  An indication of which protocol has been used when
 calculating the bandwidth values is given by the "c=" connection
 address line.  This line contains either a multicast group address or
 a unicast address of the data source or sink.  The "c=" line's
 address type may be assumed to be of the same type as the one used in
 the bandwidth calculation, although no document specifying this point
 seems to exist.
 In cases of SDP transported by RTSP, this is even less clear.  The
 normal usage for a unicast on-demand streaming session is to set the
 connection data address to a null address.  This null address does

Westerlund Standards Track [Page 6] RFC 3890 Bandwidth Modifier for SDP September 2004

 have an address type, which could be used as an indication.  However,
 this is also not clarified anywhere.
 Figure 1, illustrates a connection scenario between a streaming
 server A and a client B over a translator.  When B receives the SDP
 from A over RTSP, it will be very difficult for B to know what the
 bandwidth values in the SDP represent.  The following possibilities
 exist:
 1. The SDP is unchanged and the "c=" null address is of type IPv4.
    The bandwidth value represents the bandwidth needed in an IPv4
    network.
 2. The SDP has been changed by an Application Level Gateway (ALG).
    The "c=" address is changed to an IPv6 type.  The bandwidth value
    is unchanged.
 3. The SDP is changed and both "c=" address type and bandwidth value
    is converted.  Unfortunately, this can seldom be done, see 3.3.
 In case 1, the client can understand that the server is located in an
 IPv4 network and that it uses IPv4 overhead when calculating the
 bandwidth value.  The client can almost never convert the bandwidth
 value, see section 3.3.
 In case 2, the client does not know that the server is in an IPv4
 network and that the bandwidth value is not calculated with IPv6
 overhead.  In cases where a client uses this value to determine if
 its end of the network has sufficient resources the client will
 underestimate the required bit-rate, potentially resulting in bad
 application performance.
 In case 3, everything works correctly.  However, this case will be
 very rare.  If one tries to convert the bandwidth value without
 further information about the packet rate, significant errors may be
 introduced into the value.

3.2. Taking Other Mechanisms into Account

 Section 1.2 and 1.3 lists a number of reasons, like header
 compression and tunnels, that would change lower layer header sizes.
 For these mechanisms there exist different possibilities to take them
 into account.

Westerlund Standards Track [Page 7] RFC 3890 Bandwidth Modifier for SDP September 2004

 Using IPsec directly between end-points should definitely be known to
 the application, thus enabling it to take the extra headers into
 account.  However the same problem also exists with the current SDP
 bandwidth modifiers where a receiver is not able to convert these
 values taking the IPsec headers into account.
 It is less likely that an application would be aware of the existence
 of a virtual private network.  Thus the generality of the mechanism
 to tunnel all traffic may prevent the application from even
 considering whether it would be possible to convert the values.
 When using header compression, the actual overhead will be less
 deterministic, but in most cases an average overhead can be
 determined for a certain application.  If a network node knows that
 some type of header compression is employed, this can be taken into
 consideration.  For RSVP [15], there exists an extension, RFC 3006
 [16], that allows the data sender to inform network nodes about the
 compressibility of the data flow.  To be able to do this with any
 accuracy, the compression factor and packet rate or size is needed,
 as RFC 3006 provides.

3.3. Converting Bandwidth Values

 If one would like to convert a bandwidth value calculated using IPv4
 overhead to IPv6 overhead, the packet rate is required.  The new
 bandwidth value for IPv6 is normally "IPv4 bandwidth" + "packet rate"
 * 20 bytes, where 20 bytes is the usual difference between IPv6 and
 IPv4 headers.  The overhead difference may be some other value in
 cases when IPv4 options [14] or IPv6 extension headers [13] are used.
 As converting requires the packet rate of the stream, this is not
 possible in the general case.  Many codecs have either multiple
 possible packet/frame rates or can perform payload format
 aggregation, resulting in many possible rates.  Therefore, some extra
 information in the SDP will be required.  The "a=ptime:" parameter
 may be a possible candidate.  However, this parameter is normally
 only used for audio codecs.  Its definition [1] is that it is only a
 recommendation, which the sender may disregard.  A better parameter
 is needed.

3.4. RTCP Problems

 When RTCP is used between hosts in IPv4 and IPv6 networks over
 translator, similar problems exist.  The RTCP traffic going from the
 IPv4 domain will result in a higher RTCP bit-rate than intended in
 the IPv6 domain due to the larger headers.  This may result in up to
 a 25% increase in required bandwidth for the RTCP traffic.  The
 largest increase will be for small RTCP packets when the number of

Westerlund Standards Track [Page 8] RFC 3890 Bandwidth Modifier for SDP September 2004

 IPv4 hosts is much larger than the number of IPv6 hosts.
 Fortunately, as RTCP has a limited bandwidth compared to RTP, it will
 only result in a maximum of 1.75% increase of the total session
 bandwidth when RTCP bandwidth is 5% of RTP bandwidth.  The RTCP
 randomization may easily result in short term effects of the same
 magnitude, so this increase may be considered tolerable.  The
 increase in bandwidth will in most cases be less.
 At the same time, this results in unfairness in the reporting between
 an IPv4 and IPv6 node.  In the worst case scenario, the IPv6 node may
 report with 25% longer intervals.
 These problems have been considered insignificant enough to not be
 worth any complex solutions.  Therefore, only a simple algorithm for
 deriving RTCP bandwidth is defined in this specification.

3.5. Future Development

 Today there is work in the IETF to design a new datagram transport
 protocol suitable for real-time media.  This protocol is called the
 Datagram Congestion Control Protocol (DCCP).  It will most probably
 have a different header size than UDP, which is the protocol most
 often used for real-time media today.  This results in even more
 possible transport combinations.  This may become a problem if one
 has the possibility of using different protocols, which will not be
 determined prior to actual protocol SETUP.  Thus, pre-calculating
 this value will not be possible, which is one further motivation why
 a transport independent bandwidth modifier is needed.
 DCCP's congestion control algorithms will control how much bandwidth
 can really be utilized.  This may require further work with
 specifying SDP bandwidth modifiers to declare the dynamic
 possibilities of an application's media stream.  For example, min and
 max media bandwidth the application is capable of producing at all,
 or for media codecs only capable of producing certain bit-rates,
 enumerating possible rates.  However, this is for future study and
 outside the scope of the present solution.

3.6. Problem Conclusion

 A shortcoming of the current SDP bandwidth modifiers is that they
 also include the bandwidth needed for lower layers.  It is in many
 cases difficult to determine which lower layers and their versions
 were included in the calculation, especially in the presence of
 translation or proxying between different domains.  This prevents a
 receiver from determining if given bandwidth needs to be converted
 based on the actual lower layers being used.

Westerlund Standards Track [Page 9] RFC 3890 Bandwidth Modifier for SDP September 2004

 Secondly, an attribute to give the receiver an explicit determination
 of the maximum packet rate that will be used does not exist.  This
 value is necessary for accurate conversion of any bandwidth values if
 the difference in overhead is known.

4. Problem Scope

 The problems described in section 3 are common and effect application
 level signaling using SDP, other signaling protocols, and also
 resource reservation protocols.  However, this document targets the
 specific problem of signaling the bit-rate in SDP.  The problems need
 to be considered in other affected protocols and in new protocols
 being designed.  In the MMUSIC WG there is work on a replacement of
 SDP called SDP-NG.  It is recommended that the problems outlined in
 this document be considered when designing solutions for specifying
 bandwidth in the SDP-NG [17].
 As this specification only targets carrying the bit-rate information
 within SDP, it will have a limited applicability.  As SDP information
 is normally transported end-to-end by an application protocol, nodes
 between the end-points will not have access to the bit-rate
 information.  It will normally only be the end points that are able
 to take this information into account.  An interior node will need to
 receive the information through a means other than SDP, and that is
 outside the scope of this specification.
 Nevertheless, the bit-rate information provided in this specification
 is sufficient for cases such as first-hop resource reservation and
 admission control.  It also provide information about the maximum
 codec rate, which is independent of lower-level protocols.
 This specification does NOT try to solve the problem of detecting
 NATs or other middleboxes.

5. Requirements

 The problems outlined in the preceding sections and with the above
 applicability, should meet the following requirements:
  1. The bandwidth value SHALL be given in a way such that it can be

calculated for all possible combinations of transport overhead.

Westerlund Standards Track [Page 10] RFC 3890 Bandwidth Modifier for SDP September 2004

6. Solution

6.1. Introduction

 This chapter describes a solution for the problems outlined in this
 document for the Application Specific (AS) bandwidth modifier, thus
 enabling the derivation of the required bit-rate for an application,
 or RTP session's data and RTCP traffic.  The solution is based upon
 the definition of a new Transport Independent Application Specific
 (TIAS) bandwidth modifier and a new SDP attribute for the maximum
 packet rate (maxprate).
 The CT is a session level modifier and cannot easily be dealt with.
 To address the problems with different overhead, it is RECOMMENDED
 that the CT value be calculated using reasonable worst case overhead.
 An example of how to calculate a reasonable worst case overhead is:
 Take the overhead of the largest transport protocol (using average
 size if variable), add that to the largest IP overhead that is
 expected for use, plus the data traffic rate.  Do this for every
 individual media stream used in the conference and add them together.
 The RR and RS modifiers [9] will be used as defined and include
 transport overhead.  The small unfairness between hosts is deemed
 acceptable.

6.2. The TIAS Bandwidth Modifier

6.2.1. Usage

 A new bandwidth modifier is defined to be used for the following
 purposes:
  1. Resource reservation. A single bit-rate can be enough for use as

a resource reservation. Some characteristics can be derived from

    the stream, codec type, etc. In cases where more information is
    needed, another SDP parameter will be required.
  1. Maximum media codec rate. With the definition below of "TIAS",

the given bit-rate will mostly be from the media codec.

    Therefore, it gives a good indication of the maximum codec bit-
    rate required to be supported by the decoder.
  1. Communication bit-rate required for the stream. The "TIAS" value

together with "maxprate" can be used to determine the maximum

    communication bit-rate the stream will require.  Using session
    level values or by adding all maximum bit-rates from the streams
    in a session together, a receiver can determine if its
    communication resources are sufficient to handle the stream.  For

Westerlund Standards Track [Page 11] RFC 3890 Bandwidth Modifier for SDP September 2004

    example, a modem user can determine if the session fits his
    modem's capabilities and the established connection.
  1. Determine the RTP session bandwidth and derive the RTCP bandwidth.

The derived transport dependent attribute will be the RTP session

    bandwidth in case of RTP based transport.  The TIAS value can also
    be used to determine the RTCP bandwidth to use when using implicit
    allocation.  RTP [4] specifies that if not explicitly stated,
    additional bandwidth, equal to 5% of the RTP session bandwidth,
    shall be used by RTCP.  The RTCP bandwidth can be explicitly
    allocated by using the RR and RS modifiers defined in [9].

6.2.2. Definition

 A new session and media level bandwidth modifier is defined:
    b=TIAS:<bandwidth-value> ; see section 6.6 for ABNF definition.
 The Transport Independent Application Specific Maximum (TIAS)
 bandwidth modifier has an integer bit-rate value in bits per second.
 A fractional bandwidth value SHALL always be rounded up to the next
 integer.  The bandwidth value is the maximum needed by the
 application (SDP session level) or media stream (SDP media level)
 without counting IP or other transport layers like TCP or UDP.
 At the SDP session level, the TIAS value is the maximal amount of
 bandwidth needed when all declared media streams are used.  This MAY
 be less than the sum of all the individual media streams values.
 This is due to the possibility that not all streams have their
 maximum at the same point in time.  This can normally only be
 verified for stored media streams.
 For RTP transported media streams, TIAS at the SDP media level can be
 used to derive the RTP "session bandwidth", defined in section 6.2 of
 [4].  In the context of RTP transport, the TIAS value is defined as:
    Only the RTP payload as defined in [4] SHALL be used in the
    calculation of the bit-rate, i.e., excluding the lower layers
    (IP/UDP) and RTP headers including RTP header, RTP header
    extensions, CSRC list, and other RTP profile specific fields.
    Note that the RTP payload includes both the payload format header
    and the data.  This may allow one to use the same value for RTP-
    based media transport, non-RTP transport, and stored media.

Westerlund Standards Track [Page 12] RFC 3890 Bandwidth Modifier for SDP September 2004

 Note 1: The usage of bps is not in accordance with RFC 2327 [1].
 This change has no implications on the parser, only the interpreter
 of the value must be aware.  The change is done to allow for better
 resolution, and has also been used for the RR and RS bandwidth
 modifiers, see [9].
 Note 2: RTCP bandwidth is not included in the bandwidth value.  In
 applications using RTCP, the bandwidth used by RTCP is either 5% of
 the RTP session bandwidth including lower layers or as specified by
 the RR and RS modifiers [9].  A specification of how to derive the
 RTCP bit-rate when using TIAS is presented in chapter 6.5.

6.2.3. Usage Rules

 "TIAS" is primarily intended to be used at the SDP media level.  The
 "TIAS" bandwidth attribute MAY be present at the session level in
 SDP, if all media streams use the same transport.  In cases where the
 sum of the media level values for all media streams is larger than
 the actual maximum bandwidth need for all streams, it SHOULD be
 included at session level.  However, if present at the session level
 it SHOULD be present also at the media level.  "TIAS" SHALL NOT be
 present at the session level unless the same transport protocols is
 used for all media streams.  The same transport is used as long as
 the same combination of protocols is used, like IPv6/UDP/RTP.
 To allow for backwards compatibility with applications of SDP that do
 not implement "TIAS", it is RECOMMENDED to also include the "AS"
 modifier when using "TIAS".  The presence of a value including
 lower-layer overhead, even with its problems, is better than none.
 However, an SDP application implementing TIAS SHOULD ignore the "AS"
 value and use "TIAS" instead when both are present.
 When using TIAS for an RTP-transported stream, the "maxprate"
 attribute, if possible to calculate, defined next, SHALL be included
 at the corresponding SDP level.

6.3. Packet Rate Parameter

 To be able to calculate the bandwidth value including the lower
 layers actually used, a packet rate attribute is also defined.
 The SDP session and media level maximum packet rate attribute is
 defined as:
    a=maxprate:<packet-rate> ; see section 6.6 for ABNF definition.

Westerlund Standards Track [Page 13] RFC 3890 Bandwidth Modifier for SDP September 2004

 The <packet-rate> is a floating-point value for the stream's maximum
 packet rate in packets per second.  If the number of packets is
 variable, the given value SHALL be the maximum the application can
 produce in case of a live stream, or for stored on-demand streams,
 has produced.  The packet rate is calculated by adding the number of
 packets sent within a 1 second window.  The maxprate is the largest
 value produced when the window slides over the entire media stream.
 In cases that this can't be calculated, i.e., a live stream, a
 estimated value of the maximum packet rate the codec can produce for
 the given configuration and content SHALL be used.
 Note: The sliding window calculation will always yield an integer
 number.  However the attributes field is a floating-point value
 because the estimated or known maximum packet rate per second may be
 fractional.
 At the SDP session level, the "maxprate" value is the maximum packet
 rate calculated over all the declared media streams.  If this can't
 be measured (stored media) or estimated (live), the sum of all media
 level values provides a ceiling value.  Note: the value at session
 level can be less then the sum of the individual media streams due to
 temporal distribution of media stream's maximums.  The "maxprate"
 attribute MUST NOT be present at the session level if the media
 streams use different transport.  The attribute MAY be present if the
 media streams use the same transport.  If the attribute is present at
 the session level, it SHOULD also be present at the media level for
 all media streams.
 "maxprate" SHALL be included for all transports where a packet rate
 can be derived and TIAS is included.  For example, if you use TIAS
 and a transport like IP/UDP/RTP, for which the max packet rate
 (actual or estimated) can be derived, then "maxprate" SHALL be
 included.  However, if either (a) the packet rate for the transport
 cannot be derived, or (b) TIAS is not included, then, "maxprate" is
 not required to be included.

6.4. Converting to Transport-Dependent Values

 When converting the transport-independent bandwidth value (bw-value)
 into a transport-dependent value including the lower layers, the
 following MUST be done:
 1. Determine which lower layers will be used and calculate the sum of
    the sizes of the headers in bits (h-size).  In cases of variable
    header sizes, the average size SHALL be used.  For RTP-transported
    media, the lower layers SHALL include the RTP header with header
    extensions, if used, the CSRC list, and any profile-specific
    extensions.

Westerlund Standards Track [Page 14] RFC 3890 Bandwidth Modifier for SDP September 2004

 2. Retrieve the maximum packet rate from the SDP (prate = maxprate).
 3. Calculate the transport overhead by multiplying the header sizes
    by the packet rate (t-over = h-size * prate).
 4. Round the transport overhead up to nearest integer in bits
    (t-over = CEIL(t-over)).
 5. Add the transport overhead to the transport independent bandwidth
    value (total bit-rate = bw-value + t-over)
 When the above calculation is performed using the "maxprate", the
 bit-rate value will be the absolute maximum the media stream may use
 over the transport assumed in the calculations.

6.5. Deriving RTCP Bandwidth

 This chapter does not solve the fairness and possible bit-rate change
 introduced by IPv4 to IPv6 translation.  These differences are
 considered small enough, and known solutions introduce code changes
 to the RTP/RTCP implementation.  This section provides a consistent
 way of calculating the bit-rate to assign to RTCP, if not explicitly
 given.
 First the transport-dependent RTP session bit-rate is calculated, in
 accordance with section 6.4, using the actual transport layers used
 at the end point where the calculation is done.  The RTCP bit-rate is
 then derived as usual based on the RTP session bandwidth, i.e.,
 normally equal to 5% of the calculated value.

6.5.1. Motivation for this Solution

 Giving the exact same RTCP bit-rate value to both the IPv4 and IPv6
 hosts will result in the IPv4 host having a higher RTCP sending rate.
 The sending rate represents the number of RTCP packets sent during a
 given time interval.  The sending of RTCP is limited according to
 rules defined in the RTP specification [4].  For a 100-byte RTCP
 packet (including UDP/IPv4), the IPv4 sender has an approximately 20%
 higher sending rate.  This rate falls with larger RTCP packets.  For
 example, 300-byte packets will only give the IPv4 host a 7% higher
 sending rate.
 The above rule for deriving RTCP bandwidth gives the same behavior as
 fixed assignment when the RTP session has traffic parameters giving a
 large TIAS/maxprate ratio.  The two hosts will be fair when the
 TIAS/maxprate ratio is approximately 40 bytes/packet, given 100-byte
 RTCP packets.  For a TIAS/maxprate ratio of 5 bytes/packet, the IPv6
 host will be allowed to send approximately 15-20% more RTCP packets.

Westerlund Standards Track [Page 15] RFC 3890 Bandwidth Modifier for SDP September 2004

 The larger the RTCP packets become, the more it will favor the IPv6
 host in its sending rate.
 The conclusions is that, within the normal useful combination of
 transport-independent bit rates and packet rates, the difference in
 fairness between hosts on different IP versions with different
 overhead is acceptable.  For the 20-byte difference in overhead
 between IPv4 and IPv6 headers, the RTCP bandwidth actually used in a
 unicast connection case will not be larger than approximately 1% of
 the total session bandwidth.

6.6. ABNF Definitions

 This chapter defines in ABNF from RFC 2234 [2] the bandwidth modifier
 and the packet rate attribute.
 The bandwidth modifier:
    TIAS-bandwidth-def = "b" "=" "TIAS" ":" bandwidth-value CRLF
    bandwidth-value = 1*DIGIT
 The maximum packet rate attribute:
    max-p-rate-def = "a" "=" "maxprate" ":" packet-rate CRLF
    packet-rate = 1*DIGIT ["." 1*DIGIT]

6.7. Example

 v=0
 o=Example_SERVER 3413526809 0 IN IP4 server.example.com
 s=Example of TIAS and maxprate in use
 c=IN IP4 0.0.0.0
 b=AS:60
 b=TIAS:50780
 t=0 0
 a=control:rtsp://server.example.com/media.3gp
 a=range:npt=0-150.0
 a=maxprate:28.0
 m=audio 0 RTP/AVP 97
 b=AS:12
 b=TIAS:8480
 a=maxprate:10.0
 a=rtpmap:97 AMR/8000
 a=fmtp:97 octet-align;
 a=control:rtsp://server.example.com/media.3gp/trackID=1
 m=video 0 RTP/AVP 99

Westerlund Standards Track [Page 16] RFC 3890 Bandwidth Modifier for SDP September 2004

 b=AS:48
 b=TIAS:42300
 a=maxprate:18.0
 a=rtpmap:99 MP4V-ES/90000
 a=fmtp:99 profile-level-id=8;
 config=000001B008000001B509000001010000012000884006682C2090A21F
 a=control:rtsp://server.example.com/media.3gp/trackID=3
 In this SDP example of a streaming session's SDP, there are two media
 streams, one audio stream encoded with AMR and one video stream
 encoded with the MPEG-4 Video encoder.  AMR is used here to produce a
 constant rate media stream and uses a packetization resulting in 10
 packets per second.  This results in a TIAS bandwidth rate of 8480
 bits per second, and the claimed 10 packets per second.  The video
 stream is more variable.  However, it has a measured maximum payload
 rate of 42,300 bits per second.  The video stream also has a variable
 packet rate, despite the fact that the video is 15 frames per second,
 where at least one instance in a second long window contains 18
 packets.

7. Protocol Interaction

7.1. RTSP

 The "TIAS" and "maxprate" parameters can be used with RTSP as
 currently specified.  To be able to calculate the transport dependent
 bandwidth, some of the transport header parameters will be required.
 There should be no problem for a client to calculate the required
 bandwidth(s) prior to an RTSP SETUP.  The reason is that a client
 supports a limited number of transport setups.  The one actually
 offered to a server in a SETUP request will be dependent on the
 contents of the SDP description.  The "m=" line(s) will signal the
 desired transport profile(s) to the client.

7.2. SIP

 The usage of "TIAS" together with "maxprate" should not be different
 from the handling of the "AS" modifier currently in use.  The needed
 transport parameters will be available in the transport field in the
 "m=" line.  The address class can be determined from the "c=" field
 and the client's connectivity.

Westerlund Standards Track [Page 17] RFC 3890 Bandwidth Modifier for SDP September 2004

7.3. SAP

 In the case of SAP, all available information to calculate the
 transport dependent bit-rate should be present in the SDP.  The "c="
 information gives the address family used for the multicast.  The
 transport layer, e.g., RTP/UDP, for each media is evident in the
 media line ("m=") and its transport field.

8. Security Consideration

 The bandwidth value that is supplied by the parameters defined here
 can be altered, if not integrity protected.  By altering the
 bandwidth value, one can fool a receiver into reserving either more
 or less bandwidth than actually needed.  Reserving too much may
 result in unwanted expenses on behalf of the user, while also
 blocking resources that other parties could have used.  If too little
 bandwidth is reserved, the receiving user's quality may be effected.
 Trusting a too-large TIAS value may also result in the receiver
 rejecting the session due to insufficient communication and decoding
 resources.
 Due to these security risks, it is strongly RECOMMENDED that the SDP
 be integrity protected and source authenticated so tampering can not
 be performed, and the source can be trusted.  It is also RECOMMENDED
 that any receiver of the SDP perform an analysis of the received
 bandwidth values to verify that they are reasonable expected values
 for the application.  For example, a single channel AMR-encoded voice
 stream claiming to use 1000 kbps is not reasonable.
 Please note that some of the above security requirements are in
 conflict with that required to make signaling protocols using SDP
 work through a middlebox, as discussed in the security considerations
 of RFC 3303 [18].

9. IANA Considerations

 This document registers one new SDP session and media level attribute
 "maxprate", see section 6.3.
 A new SDP [1] bandwidth modifier (bwtype) "TIAS" is also registered
 in accordance with the rules requiring a standards-track RFC.  The
 modifier is defined in section 6.2.

Westerlund Standards Track [Page 18] RFC 3890 Bandwidth Modifier for SDP September 2004

10. Acknowledgments

 The author would like to thank Gonzalo Camarillo and Hesham Soliman
 for their work reviewing this document.  A very big thanks goes to
 Stephen Casner for reviewing and helping fix the language, and
 identifying some errors in the previous versions.  Further thanks for
 suggestion to improvements go to Colin Perkins, Geetha Srikantan, and
 Emre Aksu.
 The author would also like to thank all persons on the MMUSIC working
 group's mailing list that have commented on this specification.

11. References

11.1. Normative References

 [1]  Handley, M. and V. Jacobson, "SDP: Session Description
      Protocol", RFC 2327, April 1998.
 [2]  Crocker, D. and P. Overell, "Augmented BNF for Syntax
      Specifications: ABNF", RFC 2234, November 1997.
 [3]  Bradner, S., "Key words for use in RFCs to Indicate Requirement
      Levels", BCP 14, RFC 2119, March 1997.
 [4]  Schulzrinne, H.,  Casner, S., Frederick, R., and V. Jacobson,
      "RTP: A Transport Protocol for Real-Time Applications", STD 64,
      RFC 3550, July 2003.

11.2. Informative References

 [5]  Handley, M., Perkins, C., and E. Whelan, "Session Announcement
      Protocol", RFC 2974, October 2000.
 [6]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
      Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP:
      Session Initiation Protocol", RFC 3261, June 2002.
 [7]  Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with
      Session Description Protocol (SDP)", RFC 3264, June 2002.
 [8]  Schulzrinne, H., Rao, A., and R. Lanphier, "Real Time Streaming
      Protocol (RTSP)", RFC 2326, April 1998.
 [9]  Casner, S., "Session Description Protocol (SDP) Bandwidth
      Modifiers for RTP Control Protocol (RTCP) Bandwidth", RFC 3556,
      July 2003.

Westerlund Standards Track [Page 19] RFC 3890 Bandwidth Modifier for SDP September 2004

 [10] Degermark, M., Nordgren, B., and S. Pink, "IP Header
      Compression", RFC 2507, February 1999.
 [11] Casner, S. and V. Jacobson, "Compressing IP/UDP/RTP Headers for
      Low-Speed Serial Links", RFC 2508, February 1999.
 [12] Bormann, C., Burmeister, C., Degermark, M., Fukushima, H.,
      Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le, K., Liu,
      Z., Martensson, A., Miyazaki, A., Svanbro, K., Wiebke, T.,
      Yoshimura, T., and H. Zheng, "RObust Header Compression (ROHC):
      Framework and four profiles: RTP, UDP, ESP, and uncompressed ",
      RFC 3095, July 2001.
 [13] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
      Specification", RFC 2460, December 1998.
 [14] Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981.
 [15] Braden, R., Zhang, L., Berson, S., Herzog, S., and S. Jamin,
      "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional
      Specification", RFC 2205, September 1997.
 [16] Davie, B., Iturralde, C., Oran, D., Casner, S., and J.
      Wroclawski, "Integrated Services in the Presence of Compressible
      Flows", RFC 3006, November 2000.
 [17] Kutscher, Ott, Bormann, "Session Description and Capability
      Negotiation," Work in Progress, March 2003.
 [18] Srisuresh, P., Kuthan, J., Rosenberg, J., Molitor, A., and A.
      Rayhan, "Middlebox communication architecture and framework",
      RFC 3303, August 2002.
 [19] Kent, S. and R. Atkinson, "Security Architecture for the
      Internet Protocol", RFC 2401, November 1998.
 [20] Kent, S. and R. Atkinson, "IP Authentication Header", RFC 2402,
      November 1998.
 [21] Kent, S. and R. Atkinson, "IP Encapsulating Security Payload
      (ESP)", RFC 2406, November 1998.

Westerlund Standards Track [Page 20] RFC 3890 Bandwidth Modifier for SDP September 2004

12. Author's Address

 Magnus Westerlund
 Ericsson Research
 Ericsson AB
 Torshamnsgatan 23
 SE-164 80 Stockholm, SWEDEN
 Phone: +46 8 7190000
 EMail: Magnus.Westerlund@ericsson.com

Westerlund Standards Track [Page 21] RFC 3890 Bandwidth Modifier for SDP September 2004

13. Full Copyright Statement

 Copyright (C) The Internet Society (2004).
 This document is subject to the rights, licenses and restrictions
 contained in BCP 78, and except as set forth therein, the authors
 retain all their rights.
 This document and the information contained herein are provided on an
 "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/S HE
 REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
 INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
 IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
 THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
 WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

 The IETF takes no position regarding the validity or scope of any
 Intellectual Property Rights or other rights that might be claimed to
 pertain to the implementation or use of the technology described in
 this document or the extent to which any license under such rights
 might or might not be available; nor does it represent that it has
 made any independent effort to identify any such rights.  Information
 on the IETF's procedures with respect to rights in IETF Documents can
 be found in BCP 78 and BCP 79.
 Copies of IPR disclosures made to the IETF Secretariat and any
 assurances of licenses to be made available, or the result of an
 attempt made to obtain a general license or permission for the use of
 such proprietary rights by implementers or users of this
 specification can be obtained from the IETF on-line IPR repository at
 http://www.ietf.org/ipr.
 The IETF invites any interested party to bring to its attention any
 copyrights, patents or patent applications, or other proprietary
 rights that may cover technology that may be required to implement
 this standard.  Please address the information to the IETF at ietf-
 ipr@ietf.org.

Acknowledgement

 Funding for the RFC Editor function is currently provided by the
 Internet Society.

Westerlund Standards Track [Page 22]

/data/webs/external/dokuwiki/data/pages/rfc/rfc3890.txt · Last modified: 2004/09/07 18:53 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki