GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc1593

Network Working Group W. McKenzie Request for Comments: 1593 J. Cheng Category: Informational IBM Networking Systems

                                                            March 1994
                         SNA APPN Node MIB

Status of this Memo

 This memo provides information for the Internet community.  This memo
 does not specify an Internet standard of any kind.  Distribution of
 this memo is unlimited.

Abstract

 This RFC describes IBM's SNMP support for SNA Advanced Peer-to-Peer
 Networking (APPN) nodes.

Table of Contents

 1.0  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .  2
 2.0  Definitions   . . . . . . . . . . . . . . . . . . . . . . . .  3
 2.1  APPN Node Group   . . . . . . . . . . . . . . . . . . . . . .  3
   2.1.1  APPN Node General Information   . . . . . . . . . . . . .  4
   2.1.2  APPN Network Node Information   . . . . . . . . . . . . .  6
   2.1.3  APPN End Node Information   . . . . . . . . . . . . . . .  8
   2.1.4  APPN Port Information   . . . . . . . . . . . . . . . .   10
     2.1.4.1  General Port Information  . . . . . . . . . . . . .   10
     2.1.4.2  TCP/IP Port Information   . . . . . . . . . . . . .   14
     2.1.4.3  Data Link Switch Port Information   . . . . . . . .   15
     2.1.4.4  Token Ring Port Information   . . . . . . . . . . .   16
     2.1.4.5  Port DLC Trace Information  . . . . . . . . . . . .   17
   2.1.5  APPN Link Station Information   . . . . . . . . . . . .   23
     2.1.5.1  General Link Station Information  . . . . . . . . .   23
     2.1.5.2  TCP/IP Link Station Information   . . . . . . . . .   35
     2.1.5.3  Data Link Switch Link Station Information   . . . .   37
     2.1.5.4  Token Ring Link Station Information   . . . . . . .   39
     2.1.5.5  Link Station Status Information   . . . . . . . . .   41
   2.1.6  SNMP Performance Information for APPN Subagent  . . . .   46
   2.1.7  Performance Information for APPN Node   . . . . . . . .   49
   2.1.8  XID Statistics  . . . . . . . . . . . . . . . . . . . .   50
 2.2  APPN Topology Group   . . . . . . . . . . . . . . . . . . .   51
   2.2.1  Topology Performance Information  . . . . . . . . . . .   52
     2.2.1.1  Topology Route Information  . . . . . . . . . . . .   58
   2.2.2  Adjacent Node Table   . . . . . . . . . . . . . . . . .   60
   2.2.3  Network Node Topology   . . . . . . . . . . . . . . . .   62
     2.2.3.1  NN Topology Table (Indexed by Node Name)  . . . . .   62

McKenzie & Cheng [Page 1] RFC 1593 SNA APPN Node MIB March 1994

     2.2.3.2  NN TG Table (Indexed by Node Names and TG Number)     66
     2.2.3.3  NN Topology Table (Indexed by FRSN and Node Name)     73
     2.2.3.4  NN TG Table (Indexed by FRSN, Node Names, and TG
              Number)   . . . . . . . . . . . . . . . . . . . . .   77
 2.3  APPN Node Local Topology Group  . . . . . . . . . . . . . .   83
   2.3.1  Local Topology This Node  . . . . . . . . . . . . . . .   84
     2.3.1.1  Local General Information   . . . . . . . . . . . .   84
     2.3.1.2  Local NN Specific Information   . . . . . . . . . .   85
     2.3.1.3  Local TG Information  . . . . . . . . . . . . . . .   87
   2.3.2  Client End Nodes Topology Known to Serving NN   . . . .   93
     2.3.2.1  Client End Nodes Information  . . . . . . . . . . .   93
     2.3.2.2  Client End Nodes TG Information (Tail Vectors)  . .   94
 2.4  APPN Directory Group  . . . . . . . . . . . . . . . . . . .   99
   2.4.1  Directory Performance Information   . . . . . . . . . .   99
   2.4.2  Directory Cache Table   . . . . . . . . . . . . . . . .  102
 2.5  APPN Class Of Service Group   . . . . . . . . . . . . . . .  105
   2.5.1  COS Mode Table  . . . . . . . . . . . . . . . . . . . .  108
   2.5.2  COS Name Table  . . . . . . . . . . . . . . . . . . . .  109
   2.5.3  COS Node Row Table  . . . . . . . . . . . . . . . . . .  110
   2.5.4  COS TG Row Table  . . . . . . . . . . . . . . . . . . .  113
 3.0  Acknowledgements  . . . . . . . . . . . . . . . . . . . . .  119
 4.0  Security Considerations . . . . . . . . . . . . . . . . . .  119
 5.0  Authors' Addresses  . . . . . . . . . . . . . . . . . . . .  120

1.0 Introduction

 This module contains managed objects which describe the following:
    o   The APPN node (either an APPN network node or an APPN end node)
    o   The connections of the node to other SNA nodes
    o   The APPN network topology (as reflected in the network topology
        database that is replicated in each APPN network node.
 This module does not describe the SNA logical units (LUs) served by
 the APPN node nor does it describe the sessions between LUs.  Managed
 objects for that information are under development.

McKenzie & Cheng [Page 2] RFC 1593 SNA APPN Node MIB March 1994

2.0 Definitions

IBM-6611-APPN-MIB DEFINITIONS          ::= BEGIN
IMPORTS
        enterprises, Counter, IpAddress,
        Gauge, TimeTicks
               FROM RFC1155-SMI
        DisplayString
               FROM RFC1213-MIB
        OBJECT-TYPE
               FROM RFC-1212;
  1. - ibm OBJECT IDENTIFIER ::= { enterprises 2 } ibmProd OBJECT IDENTIFIER ::= { ibm 6 } ibm6611 OBJECT IDENTIFIER ::= { ibmProd 2 } ibmappn OBJECT IDENTIFIER ::= { ibm6611 13 } – The APPN Node Group * ibmappnNode OBJECT IDENTIFIER ::= { ibmappn 1 } ibmappnGeneralInfoAndCaps OBJECT IDENTIFIER ::= { ibmappnNode 1 } ibmappnNnUniqueInfoAndCaps OBJECT IDENTIFIER ::= { ibmappnNode 2 } ibmappnEnUniqueCaps OBJECT IDENTIFIER ::= { ibmappnNode 3 } ibmappnPortInformation OBJECT IDENTIFIER ::= { ibmappnNode 4 } ibmappnLinkStationInformation OBJECT IDENTIFIER ::= { ibmappnNode 5 } ibmappnSnmpInformation OBJECT IDENTIFIER ::= { ibmappnNode 6 } ibmappnMemoryUse OBJECT IDENTIFIER ::= { ibmappnNode 7 } ibmappnXidInformation OBJECT IDENTIFIER ::= { ibmappnNode 8 } – This group provides global information about the – APPN node, which is either a network node or an end node. – The first section applies to all APPN nodes. – The second section applies only to network nodes. – The third section applies only to end nodes. – The fourth section applies to Port information. – The fifth section applies to SNA link station Information. – The sixth section applies to SNMP traffic for this APPN sub-agent – The seventh section applies to APPN memory usage. – The eighth section applies to XID activities. McKenzie & Cheng [Page 3] RFC 1593 SNA APPN Node MIB March 1994 – APPN General Information – This section applies to both network and end nodes. ibmappnNodeCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned network name for this node in the format NETID.CPNAME." ::= { ibmappnGeneralInfoAndCaps 1 } ibmappnNodeNetid OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned APPN network identification, which can be from one to eight characters. This ID is used with the control point name to create a fully-qualified control point name." ::= { ibmappnGeneralInfoAndCaps 2 } ibmappnNodeBlockNum OBJECT-TYPE SYNTAX DisplayString (SIZE (3)) ACCESS read-only STATUS mandatory DESCRIPTION "The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product and are not configurable." ::= { ibmappnGeneralInfoAndCaps 3 } ibmappnNodeIdNum OBJECT-TYPE SYNTAX DisplayString (SIZE (5)) ACCESS read-only STATUS mandatory DESCRIPTION "The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA McKenzie & Cheng [Page 4] RFC 1593 SNA APPN Node MIB March 1994 sub-area." ::= { ibmappnGeneralInfoAndCaps 4 } ibmappnNodeType OBJECT-TYPE SYNTAX INTEGER { networkNode(1), endNode(2), len(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of APPN node, either network, len, or end node." ::= { ibmappnGeneralInfoAndCaps 5 } ibmappnNodeUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Time (in hundredths of a second) since this APPN node was initialized." ::= { ibmappnGeneralInfoAndCaps 6 } ibmappnNodeNegotLs OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports negotiable link stations." ::= { ibmappnGeneralInfoAndCaps 7 } ibmappnNodeSegReasm OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports segment reassembly. This is only supported when segment generation is also supported." ::= { ibmappnGeneralInfoAndCaps 8 } McKenzie & Cheng [Page 5] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNodeBindReasm OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports Bind segment reassembly. This will only be supported when Bind segment generation is also supported." ::= { ibmappnGeneralInfoAndCaps 9 } ibmappnNodeParallelTg OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports parallel TGs." ::= { ibmappnGeneralInfoAndCaps 10 } ibmappnNodeService OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node allows call-in from nodes not defined locally." ::= { ibmappnGeneralInfoAndCaps 11 } ibmappnNodeAdaptiveBindPacing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports adaptive bind pacing." ::= { ibmappnGeneralInfoAndCaps 12 } –
  2. - APPN Network Node Information
  3. - This section provides global information about the
  4. - APPN network node.
ibmappnNodeNnRcvRegChar OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}

McKenzie & Cheng [Page 6] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this node supports receiving registered
            characteristics."
      ::=  { ibmappnNnUniqueInfoAndCaps 1 }
ibmappnNodeNnGateway    OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this is a gateway node."
      ::=  { ibmappnNnUniqueInfoAndCaps 2 }
ibmappnNodeNnCentralDirectory  OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this node supports central directory
            cache."
      ::=  { ibmappnNnUniqueInfoAndCaps 3 }
ibmappnNodeNnTreeCache OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this node supports route tree cache."
      ::=  { ibmappnNnUniqueInfoAndCaps 4 }
ibmappnNodeNnTreeUpdate  OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this node supports
            incremental_tree_update, which is only
            supported when tree caching is supported."
      ::=  { ibmappnNnUniqueInfoAndCaps 5 }
ibmappnNodeNnRouteAddResist   OBJECT-TYPE

McKenzie & Cheng [Page 7] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Route addition resistance is a value that
          indicates the relative desirability
          of using this node for intermediate session traffic.
          The value, which can be any integer 0-255,
          is used in route computation.  The lower the value,
          the more desirable the node is for intermediate routing."
      ::=  { ibmappnNnUniqueInfoAndCaps 6 }
ibmappnNodeNnIsr   OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node supports intermediate
            session routing."
      ::=  { ibmappnNnUniqueInfoAndCaps 7 }
ibmappnNodeNnFrsn             OBJECT-TYPE
      SYNTAX INTEGER (0..65535)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Flow reduction sequence numbers (FRSNs) are associated
           with Topology Database Updates (TDUs) and are unique
           only within each APPN network node.  A TDU can be
           associated with multiple APPN resources. This object
           is the last FRSN sent in a topology update to
           adjacent network nodes."
      ::=  { ibmappnNnUniqueInfoAndCaps 8 }
  1. - – APPN End Node Information ibmappnNodeEnSegGen OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this end node supports segment generation." McKenzie & Cheng [Page 8] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnEnUniqueCaps 1 } ibmappnNodeEnModeCosMap OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this end node supports mode name to COS name mapping." ::= { ibmappnEnUniqueCaps 2 } ibmappnNodeEnLocateCdinit OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this end node supports Locate Cdinit." ::= { ibmappnEnUniqueCaps 3 } ibmappnNodeEnSendRegNames OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node will register its LUs with the adjacent serving network node: NO - do not register names YES - register names" ::= { ibmappnEnUniqueCaps 4 } ibmappnNodeEnSendRegChar OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node supports send register characteristics, which is only supported when send registered names is also supported." ::= { ibmappnEnUniqueCaps 5 } McKenzie & Cheng [Page 9] RFC 1593 SNA APPN Node MIB March 1994 –
  2. - APPN Port information
  3. -
ibmappnNodePortTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodePortEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The Port table describes the configuration and current
            status of the ports used by APPN.  The type of DLC is
            included in this table as a pointer to the DLC port
            specific tables."
      ::= { ibmappnPortInformation 1 }
ibmappnNodePortEntry OBJECT-TYPE
      SYNTAX IbmappnNodePortEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The Port Name is used as the index to this table."
      INDEX
             { ibmappnNodePortName }
      ::= { ibmappnNodePortTable 1 }
IbmappnNodePortEntry ::= SEQUENCE {
      ibmappnNodePortName            DisplayString,
      ibmappnNodePortState           INTEGER,
      ibmappnNodePortDlcType         INTEGER,
      ibmappnNodePortPortType        INTEGER,
      ibmappnNodePortSIMRIM          INTEGER,
      ibmappnNodePortLsRole          INTEGER,
      ibmappnNodePortMaxRcvBtuSize   INTEGER,
      ibmappnNodePortMaxIframeWindow INTEGER,
      ibmappnNodePortDefLsGoodXids   Counter,
      ibmappnNodePortDefLsBadXids    Counter,
      ibmappnNodePortDynLsGoodXids   Counter,
      ibmappnNodePortDynLsBadXids    Counter,
      ibmappnNodePortSpecific        OBJECT IDENTIFIER
                                   }
ibmappnNodePortName OBJECT-TYPE

McKenzie & Cheng [Page 10] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for this APPN port.
           The name can be from one to eight characters."
      ::=  { ibmappnNodePortEntry 1 }
ibmappnNodePortState        OBJECT-TYPE
      SYNTAX INTEGER    {
                         inactive(1),
                         pendactive(2),
                         active(3),
                         pendinact(4)
                         }
      ACCESS read-write
      STATUS mandatory
      DESCRIPTION
           "Indicates the current state of this port."
      ::=  { ibmappnNodePortEntry 2 }
ibmappnNodePortDlcType OBJECT-TYPE
      SYNTAX INTEGER {
                      other(1),          -- none of the following
                      sdlc(2),
                      dls(3),
                      socket(4),
                      ethernet(5),
                      tokenRing(6)
                     }
          ACCESS  read-only
          STATUS  mandatory
          DESCRIPTION
                  "The type of DLC interface, distinguished according
                  to the protocol immediately 'below' this layer."
      ::=  { ibmappnNodePortEntry 3 }
ibmappnNodePortPortType  OBJECT-TYPE
      SYNTAX INTEGER {
                     leased(1),
                     switched(2),
                     sharedAccessFacilities(3)
              }
      ACCESS read-only
      STATUS mandatory

McKenzie & Cheng [Page 11] RFC 1593 SNA APPN Node MIB March 1994

      DESCRIPTION
           "Identifies the type of line used by this port."
      ::=  { ibmappnNodePortEntry 4 }
ibmappnNodePortSIMRIM  OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether Set Initialization Mode (SIM) and
            Receive Initialization Mode (RIM) are supported."
      ::=  { ibmappnNodePortEntry 5 }
ibmappnNodePortLsRole OBJECT-TYPE
      SYNTAX INTEGER {
                     primary(1),
                     secondary(2),
                     negotiable(3),
                     abm(4)
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Initial role for LSs activated through this port,
           where 'abm' indicates asynchronous balance mode."
      ::=  { ibmappnNodePortEntry 6 }
ibmappnNodePortMaxRcvBtuSize OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Maximum Basic Transmission Size (BTU) that a
           link station on this port can receive."
      ::=  { ibmappnNodePortEntry 7 }
ibmappnNodePortMaxIframeWindow OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Maximum number of I-frames that can be received
           by the XID sender before an acknowledgement is received."

McKenzie & Cheng [Page 12] RFC 1593 SNA APPN Node MIB March 1994

      ::=  { ibmappnNodePortEntry 8 }
ibmappnNodePortDefLsGoodXids    OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of successfull XIDs that have occurred
             on all defined link stations on this port since the last
             time this port was started."
      ::=  { ibmappnNodePortEntry 9 }
ibmappnNodePortDefLsBadXids    OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of unsuccessfull XIDs that have occurred
             on all defined link stations on this port since the last
             time this port was started."
      ::=  { ibmappnNodePortEntry 10 }
ibmappnNodePortDynLsGoodXids    OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of successfull XIDs that have occurred
             on all dynamic link stations on this port since the last
             time this port was started."
      ::=  { ibmappnNodePortEntry 11 }
ibmappnNodePortDynLsBadXids    OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of unsuccessfull XIDs that have occurred
             on all dynamic link stations on this port since the last
             time this port was started."
      ::=  { ibmappnNodePortEntry 12 }
ibmappnNodePortSpecific OBJECT-TYPE
      SYNTAX OBJECT IDENTIFIER

McKenzie & Cheng [Page 13] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Identifies the port specific OBJECT IDENTIFIER
            that can provide additional information."
      ::=  { ibmappnNodePortEntry 13 }
  1. - – – ibmappnNodePortIpTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNodePortIpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Port table (TCP/IP specific)." ::= { ibmappnPortInformation 2 } ibmappnNodePortIpEntry OBJECT-TYPE SYNTAX IbmappnNodePortIpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The IP Name is used as the index to this table." INDEX {ibmappnNodePortIpName } ::= { ibmappnNodePortIpTable 1 } IbmappnNodePortIpEntry ::= SEQUENCE { ibmappnNodePortIpName DisplayString, ibmappnNodePortIpPortNum INTEGER } ibmappnNodePortIpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for this APPN port. The name can be from one to eight characters." McKenzie & Cheng [Page 14] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNodePortIpEntry 1 } ibmappnNodePortIpPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Local TCP/IP port number." ::= { ibmappnNodePortIpEntry 2 } –
  2. -
  3. -
ibmappnNodePortDlsTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodePortDlsEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Port table (DLS specific)."
      ::= { ibmappnPortInformation 3 }
ibmappnNodePortDlsEntry OBJECT-TYPE
      SYNTAX IbmappnNodePortDlsEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The DLS Name is used as the index to this table."
      INDEX
             {ibmappnNodePortDlsName }
      ::= { ibmappnNodePortDlsTable 1 }
IbmappnNodePortDlsEntry ::= SEQUENCE {
      ibmappnNodePortDlsName         DisplayString,
      ibmappnNodePortDlsMac          OCTET STRING,
      ibmappnNodePortDlsSap          OCTET STRING
                                   }
ibmappnNodePortDlsName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory

McKenzie & Cheng [Page 15] RFC 1593 SNA APPN Node MIB March 1994

      DESCRIPTION
          "Administratively-assigned name for this APPN DLS port.
           The name can be from one to eight characters."
      ::=  { ibmappnNodePortDlsEntry 1 }
ibmappnNodePortDlsMac OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (6))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local DLS MAC address."
      ::=  { ibmappnNodePortDlsEntry 2 }
ibmappnNodePortDlsSap OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (1))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local DLS Sap address."
      ::=  { ibmappnNodePortDlsEntry 3 }
  1. - – – ibmappnNodePortTrTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNodePortTrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Port table (Token Ring specific)." ::= { ibmappnPortInformation 4 } ibmappnNodePortTrEntry OBJECT-TYPE SYNTAX IbmappnNodePortTrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The TR Name is used as the index to this table." INDEX {ibmappnNodePortTrName } McKenzie & Cheng [Page 16] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNodePortTrTable 1 } IbmappnNodePortTrEntry ::= SEQUENCE { ibmappnNodePortTrName DisplayString, ibmappnNodePortTrMac OCTET STRING, ibmappnNodePortTrSap OCTET STRING } ibmappnNodePortTrName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for this APPN port. The name can be from one to eight characters." ::= { ibmappnNodePortTrEntry 1 } ibmappnNodePortTrMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Local Token Ring MAC address." ::= { ibmappnNodePortTrEntry 2 } ibmappnNodePortTrSap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "Local Token Ring Sap address." ::= { ibmappnNodePortTrEntry 3 } –
  2. - APPN generic DLC Trace
  3. -
ibmappnNodePortDlcTraceTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodePortDlcTraceEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Port table generic DLC trace table."

McKenzie & Cheng [Page 17] RFC 1593 SNA APPN Node MIB March 1994

      ::= { ibmappnPortInformation 5 }
ibmappnNodePortDlcTraceEntry OBJECT-TYPE
      SYNTAX IbmappnNodePortDlcTraceEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The Port name and a dynamic integer are the index to
           this table."
      INDEX
             {ibmappnNodePortDlcTracPortName,
              ibmappnNodePortDlcTracIndex}
      ::= { ibmappnNodePortDlcTraceTable 1 }
IbmappnNodePortDlcTraceEntry ::= SEQUENCE {
       ibmappnNodePortDlcTracPortName     DisplayString,
       ibmappnNodePortDlcTracIndex        INTEGER,
       ibmappnNodePortDlcTracDlcType      INTEGER,
       ibmappnNodePortDlcTracLocalAddr    DisplayString,
       ibmappnNodePortDlcTracRemoteAddr   DisplayString,
       ibmappnNodePortDlcTracMsgType      INTEGER,
       ibmappnNodePortDlcTracCmdType      INTEGER,
       ibmappnNodePortDlcTracUseWan       INTEGER
                                   }
ibmappnNodePortDlcTracPortName OBJECT-TYPE
      SYNTAX  DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
            "The Port name associated with this this trace table entry."
      ::=  { ibmappnNodePortDlcTraceEntry 1 }
ibmappnNodePortDlcTracIndex OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
            "This index value is updated every time a new trace entry
             is created which provides a means to retrieve only the
             updated entries and also provides a simple method of
             correlating the entries.  The table will wrap when the
             table is full, which will result in previous entries
             being written over.  The mangement station can over
             come this by retrieving the table using this index to

McKenzie & Cheng [Page 18] RFC 1593 SNA APPN Node MIB March 1994

             retrieve only the new table entries."
      ::=  { ibmappnNodePortDlcTraceEntry 2 }
ibmappnNodePortDlcTracDlcType OBJECT-TYPE
      SYNTAX INTEGER {
                      other(1),          -- none of the following
                      sdlc(2),
                      dls(3),
                      socket(4),
                      ethernet(5),
                      tokenRing(6)
                     }
          ACCESS  read-only
          STATUS  mandatory
          DESCRIPTION
                  "The type of DLC interface, distinguished according
                  to the protocol immediately 'below' this layer."
      ::=  { ibmappnNodePortDlcTraceEntry 3 }
ibmappnNodePortDlcTracLocalAddr OBJECT-TYPE
      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local address in format described below:
           other    = free form DisplayString
           ip       = ld. ld. ld. ld / 2d
           tr       = lx: lx: lx: lx: lx: lx . lx
           dlsw     = lx: lx: lx: lx: lx: lx . lx
           ethernet = lx: lx: lx: lx: lx: lx . lx
           "
      ::=  { ibmappnNodePortDlcTraceEntry 4 }
ibmappnNodePortDlcTracRemoteAddr OBJECT-TYPE
      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Remote Address in the format described below:
           other    = free form DisplayString
           ip       = ld. ld. ld. ld / 2d
           tr       = lx: lx: lx: lx: lx: lx . lx
           dlsw     = lx: lx: lx: lx: lx: lx . lx

McKenzie & Cheng [Page 19] RFC 1593 SNA APPN Node MIB March 1994

           ethernet = lx: lx: lx: lx: lx: lx . lx
           "
      ::=  { ibmappnNodePortDlcTraceEntry 5 }
ibmappnNodePortDlcTracMsgType OBJECT-TYPE
      SYNTAX INTEGER    {
--              enumeration values between 1 and 1999 are reserved
--              for potential undefined message types.
                         other(1),
                         unknown(2),
                         request(3),
                         confirm(4),
                         indication(5),
                         response(6)
  1. - enumeration values between 2000 and 3999 are reserved
  2. - for IP socket traces,
  1. - enumeration values between 4000 and 5999 are reserved
  2. - for DLS traces,
  1. - enumeration values between 6000 and 7999 are reserved
  2. - for TR traces,
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
            "Indicates the type of trace record entry"
      ::=  { ibmappnNodePortDlcTraceEntry 6 }
ibmappnNodePortDlcTracCmdType OBJECT-TYPE
      SYNTAX INTEGER    {
--              enumeration values between 1 and 1999 are reserved
--              for potential undefined message types.
                         testFrame(1),
                         respFrame(2),
                         curFrame(3),
                         icrFrame(4),

McKenzie & Cheng [Page 20] RFC 1593 SNA APPN Node MIB March 1994

                         respAck(5),
                         dgrmFrame(6),
                         xidFrame(7),
                         contFrame(8),
                         contedFrame(9),
                         iFrame(10),
                         enterBusy(12),
                         exitBusy(13),
                         haltFrame(14),
                         lsHalted(15),
                         restartLs(16),
                         lsRestarted(17),
                         netBioSnq(18),
                         netBioSnr(19),
                         gnetFrame(20),
                         netdFrame(21),
                         oobFrame(22),
                         alterSap(23),
                         testRsp(24),
                         haltLsNow(25),
                         testReq(26),
  1. - enumeration values between 2000 and 3999 are reserved
  2. - for IP socket traces.

ipTestFrame(2001),

                         ipRespFrame(2002),
                         ipCurFrame(2003),
                         ipIcrFrame(2004),
                         ipRespAck(2005),
                         ipDgrmFrame(2006),
                         ipXidFrame(2007),
                         ipContFrame(2008),
                         ipContedFrame(2009),
                         ipIFrame(2010),
                         ipEnterBusy(2012),
                         ipExitBusy(2013),
                         ipHaltFrame(2014),
                         ipLsHalted(2015),
                         ipRestartLs(2016),
                         ipLsRestarted(2017),
                         ipNetBioSnq(2018),
                         ipNetBioSnr(2019),
                         ipGnetFrame(2020),
                         ipNetdFrame(2021),
                         ipOobFrame(2022),
                         ipAlterSap(2023),
                         ipTestRsp(2024),
                         ipHaltLsNow(2025),

McKenzie & Cheng [Page 21] RFC 1593 SNA APPN Node MIB March 1994

                         ipTestReq(2026),
  1. - enumeration values between 4000 and 5999 are reserved
  2. - for DLS traces.
                         dlsIpm(4124),
  1. - enumeration values between 6000 and 7999 are reserved for
  2. - TR traces.

trTestFrame(6001),

                         trRespFrame(6002),
                         trCurFrame(6003),
                         trIcrFrame(6004),
                         trRespAck(6005),
                         trDgrmFrame(6006),
                         trXidFrame(6007),
                         trContFrame(6008),
                         trContedFrame(6009),
                         trIFrame(6010),
                         trEnterBusy(6012),
                         trExitBusy(6013),
                         trHaltFrame(6014),
                         trLsHalted(6015),
                         trRestartLs(6016),
                         trLsRestarted(6017),
                         trNetBioSnq(6018),
                         trNetBioSnr(6019),
                         trGnetFrame(6020),
                         trNetdFrame(6021),
                         trOobFrame(6022),
                         trAlterSap(6023),
                         trTestRsp(6024),
                         trHaltLsNow(6025),
                         trTestReq(6026)
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
            "Indicates the command type of the trace entry."
      ::=  { ibmappnNodePortDlcTraceEntry 7 }
ibmappnNodePortDlcTracUseWan OBJECT-TYPE
      SYNTAX INTEGER    {
                         other(1),
                         notApplicable(2),
                         useUnknown(3),

McKenzie & Cheng [Page 22] RFC 1593 SNA APPN Node MIB March 1994

                         useWan(4),
                         useLan(5)
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
            "Indicates the type of connection of the trace entry.
            For example, token ring and ethernet ports will have
            useLan as connection.  For the dls port, it could be
            either useWan if connection is across Wan via dls
            sessions, or useLan if connection is to a local attached
            LAN."
      ::=  { ibmappnNodePortDlcTraceEntry 8 }
  1. - – APPN Link Station Information – ibmappnNodeLsTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNodeLsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains detail information about the link station configuration and current status." ::= { ibmappnLinkStationInformation 1 } ibmappnNodeLsEntry OBJECT-TYPE SYNTAX IbmappnNodeLsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is indexed by the link station name." INDEX { ibmappnNodeLsName } ::= { ibmappnNodeLsTable 1 } IbmappnNodeLsEntry ::= SEQUENCE { ibmappnNodeLsName DisplayString, ibmappnNodeLsPortName DisplayString, ibmappnNodeLsDlcType INTEGER, McKenzie & Cheng [Page 23] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNodeLsDynamic INTEGER, ibmappnNodeLsState INTEGER, – ls defined data / xid info ibmappnNodeLsCpName DisplayString, ibmappnNodeLsTgNum INTEGER, ibmappnNodeLsLimResource INTEGER, ibmappnNodeLsMigration INTEGER, ibmappnNodeLsBlockNum DisplayString, ibmappnNodeLsIdNum DisplayString, ibmappnNodeLsCpCpSession INTEGER, – ls parms (common) / xid info ibmappnNodeLsTargetPacingCount INTEGER, ibmappnNodeLsMaxSendBtuSize INTEGER, – tg characteristics ibmappnNodeLsEffCap INTEGER, ibmappnNodeLsConnCost INTEGER, ibmappnNodeLsByteCost INTEGER, ibmappnNodeLsSecurity INTEGER, ibmappnNodeLsDelay INTEGER, ibmappnNodeLsUsr1 INTEGER, ibmappnNodeLsUsr2 INTEGER, ibmappnNodeLsUsr3 INTEGER, – ls (performance data) ibmappnNodeLsInXidBytes Counter, ibmappnNodeLsInMsgBytes Counter, ibmappnNodeLsInXidFrames Counter, ibmappnNodeLsInMsgFrames Counter, ibmappnNodeLsOutXidBytes Counter, ibmappnNodeLsOutMsgBytes Counter, ibmappnNodeLsOutXidFrames Counter, ibmappnNodeLsOutMsgFrames Counter, – ls (propgation delay) ibmappnNodeLsEchoRsps Counter, ibmappnNodeLsCurrentDelay INTEGER, ibmappnNodeLsMaxDelay INTEGER, ibmappnNodeLsMinDelay INTEGER, ibmappnNodeLsMaxDelayTime TimeTicks, – ls (Xid Statistics) ibmappnNodeLsGoodXids Counter, ibmappnNodeLsBadXids Counter, – Dlc specific ibmappnNodeLsSpecific OBJECT IDENTIFIER, ibmappnNodeLsSubState INTEGER, ibmappnNodeLsStartTime TimeTicks, ibmappnNodeLsActiveTime TimeTicks, ibmappnNodeLsCurrentStateTime TimeTicks } McKenzie & Cheng [Page 24] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNodeLsName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for the link station. The name can be from one to eight characters." ::= { ibmappnNodeLsEntry 1 } ibmappnNodeLsPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for the port. The name can be from one to eight characters." ::= { ibmappnNodeLsEntry 2 } ibmappnNodeLsDlcType OBJECT-TYPE SYNTAX INTEGER { other(1), – none of the following sdlc(2), dls(3), socket(4), ethernet(5), tokenRing(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of DLC interface, distinguished according to the protocol immediately 'below' this layer." ::= { ibmappnNodeLsEntry 3 } ibmappnNodeLsDynamic OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Identifies whether this resource is a dynamic link station. Dynamic link stations are created when adjacent nodes that have not been locally defined establish a connection with this node." McKenzie & Cheng [Page 25] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNodeLsEntry 4 } ibmappnNodeLsState OBJECT-TYPE SYNTAX INTEGER { inactive(1), pendactive(2), active(3), pendinact(4) } ACCESS read-write STATUS mandatory DESCRIPTION "State of this link station." ::= { ibmappnNodeLsEntry 5 } ibmappnNodeLsCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Fully-qualified name of the adjacent node for this link station. The name can be from three to seventeen characters. Format is netid.cpname." ::= { ibmappnNodeLsEntry 6 } ibmappnNodeLsTgNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number associated with the TG to this link station." ::= { ibmappnNodeLsEntry 7 } ibmappnNodeLsLimResource OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the link station is a limited resource. If it is, the TG is deactivated when there are no sessions." ::= { ibmappnNodeLsEntry 8 } McKenzie & Cheng [Page 26] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNodeLsMigration OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this link station will be used for connections to down-level or migration partners." ::= { ibmappnNodeLsEntry 9 } ibmappnNodeLsBlockNum OBJECT-TYPE SYNTAX DisplayString (SIZE (3)) ACCESS read-only STATUS mandatory DESCRIPTION "The block number is the first three digits of the node_id. These 3 hexideimal digits identify the product and are not configurable." ::= { ibmappnNodeLsEntry 10 } ibmappnNodeLsIdNum OBJECT-TYPE SYNTAX DisplayString (SIZE (5)) ACCESS read-only STATUS mandatory DESCRIPTION "The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA sub-area." ::= { ibmappnNodeLsEntry 11 } ibmappnNodeLsCpCpSession OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether CP-CP sessions are supported by this link station." ::= { ibmappnNodeLsEntry 12 } ibmappnNodeLsTargetPacingCount OBJECT-TYPE SYNTAX INTEGER McKenzie & Cheng [Page 27] RFC 1593 SNA APPN Node MIB March 1994 ACCESS read-only STATUS mandatory DESCRIPTION "Numeric value between 0 and 32767 inclusive indicating the desired pacing window size for BINDs on this TG. The number is significant only when fixed bind pacing is being performed." ::= { ibmappnNodeLsEntry 13 } ibmappnNodeLsMaxSendBtuSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Numeric value between 0 and 32767 inclusive indicating the desired number of bytes in a Basic Transmission Unit (BTU) that can be sent on this TG. This is an administratively assigned value." ::= { ibmappnNodeLsEntry 14 } ibmappnNodeLsEffCap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 15 } ibmappnNodeLsConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with the TG using this link station." McKenzie & Cheng [Page 28] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNodeLsEntry 16 } ibmappnNodeLsByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 17 } ibmappnNodeLsSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), –X'01' publicSwitchedNetwork(32), –X'20' undergroundCable(64), –X'40' secureConduit(96), –X'60' guardedConduit(128), –X'80' encrypted(160), –X'A0' guardedRadiation(192) –X'C0' } ACCESS read-only STATUS mandatory DESCRIPTION "The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 18 } ibmappnNodeLsDelay OBJECT-TYPE SYNTAX INTEGER { minimum(0), –X'00' negligible(384), –X'4C' terrestrial(9216), –X'71' packet(147456), –X'91' long(294912), –X'99' maximum(2013265920) –X'FF' } ACCESS read-only STATUS mandatory DESCRIPTION "Relative amount of time that it takes for a signal to McKenzie & Cheng [Page 29] RFC 1593 SNA APPN Node MIB March 1994 travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 19 } ibmappnNodeLsUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 20 } ibmappnNodeLsUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 21 } ibmappnNodeLsUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station." ::= { ibmappnNodeLsEntry 22 } ibmappnNodeLsInXidBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory McKenzie & Cheng [Page 30] RFC 1593 SNA APPN Node MIB March 1994 DESCRIPTION "Number of XID bytes received." ::= { ibmappnNodeLsEntry 23 } ibmappnNodeLsInMsgBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of message (I-frame) bytes received." ::= { ibmappnNodeLsEntry 24 } ibmappnNodeLsInXidFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of XID frames received." ::= { ibmappnNodeLsEntry 25 } ibmappnNodeLsInMsgFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of message (I-frame) frames received." ::= { ibmappnNodeLsEntry 26 } ibmappnNodeLsOutXidBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of XID bytes sent." ::= { ibmappnNodeLsEntry 27 } ibmappnNodeLsOutMsgBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of message (I-frame) bytes sent." McKenzie & Cheng [Page 31] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNodeLsEntry 28 } ibmappnNodeLsOutXidFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of XID frames sent." ::= { ibmappnNodeLsEntry 29 } ibmappnNodeLsOutMsgFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of message (I-frame) frames sent." ::= { ibmappnNodeLsEntry 30 } ibmappnNodeLsEchoRsps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of responses returned from adjacent link station. A response should be returned for each test frame sent by this node. Test frames are sent to adjacent nodes periodically to verify connectivity and to measure that actual round trip time, that is the time the test frame is sent until the response is received." ::= { ibmappnNodeLsEntry 31 } ibmappnNodeLsCurrentDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The time that it took for the last test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds." ::= { ibmappnNodeLsEntry 32 } ibmappnNodeLsMaxDelay OBJECT-TYPE McKenzie & Cheng [Page 32] RFC 1593 SNA APPN Node MIB March 1994 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The longest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds ." ::= { ibmappnNodeLsEntry 33 } ibmappnNodeLsMinDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The shortest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds." ::= { ibmappnNodeLsEntry 34 } ibmappnNodeLsMaxDelayTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (since system up in hundredth of seconds) when the longest delay occurred. This time can be used to identify when this high water mark occurred in relation to the last initialization of the APPN node." ::= { ibmappnNodeLsEntry 35 } ibmappnNodeLsGoodXids OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of successful XIDs that have occurred on this link station since the time it was started." ::= { ibmappnNodeLsEntry 36 } ibmappnNodeLsBadXids OBJECT-TYPE SYNTAX Counter McKenzie & Cheng [Page 33] RFC 1593 SNA APPN Node MIB March 1994 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of unsuccessful XIDs that have occurred on this link station since the time it was started." ::= { ibmappnNodeLsEntry 37 } ibmappnNodeLsSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "Identifies the DLC specific OBJECT IDENTIFIER that can provide additional information." ::= { ibmappnNodeLsEntry 38 } ibmappnNodeLsSubState OBJECT-TYPE SYNTAX INTEGER { inactive(1), sentReqOpnstn(2), pendXidExch(3), sentActAs(4), sentSetMode(5), active(6), sentDeactAsOrd(7), sentDiscOrd(8), sentDestroyTg(9), sentCreateTg(10), sentConnReq(11), pendRcvConnInd(12), pendSendConnRsp(13), sentConnRsp(14), pendDeact(15) } ACCESS read-only STATUS mandatory DESCRIPTION "State of this link station." ::= { ibmappnNodeLsEntry 39 } ibmappnNodeLsStartTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION McKenzie & Cheng [Page 34] RFC 1593 SNA APPN Node MIB March 1994 "The time (in hundredth of seconds) this link station has been active the last time since the time APPN was initialized." ::= { ibmappnNodeLsEntry 40 } ibmappnNodeLsActiveTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (in hundredth of seconds) this link station has been in the active state. A zero value indicates the link station has never been active." ::= { ibmappnNodeLsEntry 41 } ibmappnNodeLsCurrentStateTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (in hundredth of seconds) the link station is in the current state." ::= { ibmappnNodeLsEntry 42 } –
  2. - Link station table (TCP/IP specific)
  3. -
ibmappnNodeLsIpTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodeLsIpEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
          "Link station table (TCP/IP specific)."
      ::= { ibmappnLinkStationInformation 2 }
ibmappnNodeLsIpEntry OBJECT-TYPE
      SYNTAX IbmappnNodeLsIpEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The IP Name is used as the index to this table."

McKenzie & Cheng [Page 35] RFC 1593 SNA APPN Node MIB March 1994

      INDEX
             {ibmappnNodeLsIpName }
      ::= { ibmappnNodeLsIpTable 1 }
IbmappnNodeLsIpEntry ::= SEQUENCE {
      ibmappnNodeLsIpName             DisplayString,
      ibmappnNodeLsIpState            INTEGER,
      ibmappnNodeLsLocalIpAddr        IpAddress,
      ibmappnNodeLsLocalIpPortNum     INTEGER,
      ibmappnNodeLsRemoteIpAddr       IpAddress,
      ibmappnNodeLsRemoteIpPortNum    INTEGER
                                   }
ibmappnNodeLsIpName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for this link station. The
           name can be from one to eight characters."
      ::=  { ibmappnNodeLsIpEntry 1 }
ibmappnNodeLsIpState        OBJECT-TYPE
      SYNTAX INTEGER    {
                         inactive(1),
                         pendactive(2),
                         active(3),
                         pendinact(4)
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "State of this link station."
      ::=  { ibmappnNodeLsIpEntry 2 }
ibmappnNodeLsLocalIpAddr OBJECT-TYPE
      SYNTAX IpAddress
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local IP address."
      ::=  { ibmappnNodeLsIpEntry 3 }
ibmappnNodeLsLocalIpPortNum OBJECT-TYPE

McKenzie & Cheng [Page 36] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local TCP/IP port number.
            The default listening port will be administratively
            assigned and will dynamically change if this node
            initiates a session with adjacent node."
      ::=  { ibmappnNodeLsIpEntry 4 }
ibmappnNodeLsRemoteIpAddr OBJECT-TYPE
      SYNTAX IpAddress
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Remote IP address."
      ::=  { ibmappnNodeLsIpEntry 5 }
ibmappnNodeLsRemoteIpPortNum OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Remote TCP/IP port number."
      ::=  { ibmappnNodeLsIpEntry 6 }
  1. - – Ls Table (DLS specific) – ibmappnNodeLsDlsTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNodeLsDlsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Ls Table (DLS specific)." ::= { ibmappnLinkStationInformation 3 } ibmappnNodeLsDlsEntry OBJECT-TYPE SYNTAX IbmappnNodeLsDlsEntry McKenzie & Cheng [Page 37] RFC 1593 SNA APPN Node MIB March 1994 ACCESS not-accessible STATUS mandatory DESCRIPTION "The DLS Name is used as the index to this table." INDEX {ibmappnNodeLsDlsName } ::= { ibmappnNodeLsDlsTable 1 } IbmappnNodeLsDlsEntry ::= SEQUENCE { ibmappnNodeLsDlsName DisplayString, ibmappnNodeLsDlsState INTEGER, ibmappnNodeLsLocalDlsMac OCTET STRING, ibmappnNodeLsLocalDlsSap OCTET STRING, ibmappnNodeLsRemoteDlsMac OCTET STRING, ibmappnNodeLsRemoteDlsSap OCTET STRING } ibmappnNodeLsDlsName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for this link station. The name can be from one to eight characters." ::= { ibmappnNodeLsDlsEntry 1 } ibmappnNodeLsDlsState OBJECT-TYPE SYNTAX INTEGER { inactive(1), pendactive(2), active(3), pendinact(4) } ACCESS read-only STATUS mandatory DESCRIPTION "State of this link station." ::= { ibmappnNodeLsDlsEntry 2 } ibmappnNodeLsLocalDlsMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION McKenzie & Cheng [Page 38] RFC 1593 SNA APPN Node MIB March 1994 "Local MAC address." ::= { ibmappnNodeLsDlsEntry 3 } ibmappnNodeLsLocalDlsSap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "Local SAP address." ::= { ibmappnNodeLsDlsEntry 4 } ibmappnNodeLsRemoteDlsMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC address." ::= { ibmappnNodeLsDlsEntry 5 } ibmappnNodeLsRemoteDlsSap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote SAP address." ::= { ibmappnNodeLsDlsEntry 6 } –
  2. - Ls Table (Token Ring specific)
  3. -
ibmappnNodeLsTrTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodeLsTrEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Ls Table (Token Ring specific)."
      ::= { ibmappnLinkStationInformation 4 }
ibmappnNodeLsTrEntry OBJECT-TYPE
      SYNTAX IbmappnNodeLsTrEntry

McKenzie & Cheng [Page 39] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The TR Name is used as the index to this table."
      INDEX
             {ibmappnNodeLsTrName }
      ::= { ibmappnNodeLsTrTable 1 }
IbmappnNodeLsTrEntry ::= SEQUENCE {
      ibmappnNodeLsTrName            DisplayString,
      ibmappnNodeLsTrState           INTEGER,
      ibmappnNodeLsLocalTrMac        OCTET STRING,
      ibmappnNodeLsLocalTrSap        OCTET STRING,
      ibmappnNodeLsRemoteTrMac       OCTET STRING,
      ibmappnNodeLsRemoteTrSap       OCTET STRING
                                   }
ibmappnNodeLsTrName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for this link station.
           The name can be from one to eight characters."
      ::=  { ibmappnNodeLsTrEntry 1 }
ibmappnNodeLsTrState        OBJECT-TYPE
      SYNTAX INTEGER    {
                         inactive(1),
                         pendactive(2),
                         active(3),
                         pendinact(4)
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "State of this link station."
      ::=  { ibmappnNodeLsTrEntry 2 }
ibmappnNodeLsLocalTrMac OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (6))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local MAC address."

McKenzie & Cheng [Page 40] RFC 1593 SNA APPN Node MIB March 1994

      ::=  { ibmappnNodeLsTrEntry 3 }
ibmappnNodeLsLocalTrSap OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (1))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Local SAP address."
      ::=  { ibmappnNodeLsTrEntry 4 }
ibmappnNodeLsRemoteTrMac OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (6))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Remote MAC address."
      ::=  { ibmappnNodeLsTrEntry 5 }
ibmappnNodeLsRemoteTrSap OBJECT-TYPE
      SYNTAX OCTET STRING (SIZE (1))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Remote SAP address."
      ::=  { ibmappnNodeLsTrEntry 6 }
  1. - – This table provides information about errors this node encountered – with connections to adjacent nodes. This includes all exceptional – conditions encountered establishing connections and all exceptional – conditions that result in terminating the connection. –
ibmappnNodeLsStatusTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnNodeLsStatusEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table contains information related to exceptional
            and potential exceptional conditions that occur during
            the activation, XID exchange, and termination of the
            connection."
      ::= { ibmappnLinkStationInformation 5 }

McKenzie & Cheng [Page 41] RFC 1593 SNA APPN Node MIB March 1994

ibmappnNodeLsStatusEntry OBJECT-TYPE
      SYNTAX IbmappnNodeLsStatusEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table is indexed by the LsStatusIndex, which is an
            integer that is continuously updated until it eventually
            wraps.  This provides the management station the ability
            to retrieve only the updates to the table by using the
            standard GET NEXT."
      INDEX
             { ibmappnNodeLsStatusIndex }
      ::= { ibmappnNodeLsStatusTable 1 }
IbmappnNodeLsStatusEntry ::= SEQUENCE {
      ibmappnNodeLsStatusIndex              INTEGER,
      ibmappnNodeLsStatusTime               TimeTicks,
      ibmappnNodeLsStatusLsName             DisplayString,
      ibmappnNodeLsStatusCpName             DisplayString,
      ibmappnNodeLsStatusNodeId             OCTET STRING,
      ibmappnNodeLsStatusTgNum              INTEGER,
      ibmappnNodeLsStatusGeneralSense       OCTET STRING,
      ibmappnNodeLsStatusNofRetry           INTEGER,
      ibmappnNodeLsStatusEndSense           OCTET STRING,
      ibmappnNodeLsStatusXidLocalSense      OCTET STRING,
      ibmappnNodeLsStatusXidRemoteSense     OCTET STRING,
      ibmappnNodeLsStatusXidByteInError     INTEGER,
      ibmappnNodeLsStatusXidBitInError      INTEGER,
      ibmappnNodeLsStatusDlcType            INTEGER,
      ibmappnNodeLsStatusLocalAddr          DisplayString,
      ibmappnNodeLsStatusRemoteAddr         DisplayString
                                   }
ibmappnNodeLsStatusIndex       OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This index is continuous index this table."
      ::=  { ibmappnNodeLsStatusEntry 1 }
ibmappnNodeLsStatusTime    OBJECT-TYPE
      SYNTAX TimeTicks
      ACCESS read-only

McKenzie & Cheng [Page 42] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
          "Time (in hundreds of a second) since this node was last
           initialized."
      ::=  { ibmappnNodeLsStatusEntry 2 }
ibmappnNodeLsStatusLsName       OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for this link station."
      ::=  { ibmappnNodeLsStatusEntry 3 }
ibmappnNodeLsStatusCpName    OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned fully-qualified name of the
           adjacent node partner.  This will be provided when the
           adjacent node has been defined at this node or when the
           XID sequence has proceeded far enough to to identify the
           adjacent node.  A blank CP name will indicate the name is
           unknown."
      ::=  { ibmappnNodeLsStatusEntry 4 }
ibmappnNodeLsStatusNodeId       OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Adjacent Node id"
      ::=  { ibmappnNodeLsStatusEntry 5 }
ibmappnNodeLsStatusTgNum   OBJECT-TYPE
      SYNTAX INTEGER (0..256)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Number associated with the TG to this link station
           with a range from 0 to 256.  A value of 256 indicates

McKenzie & Cheng [Page 43] RFC 1593 SNA APPN Node MIB March 1994

           the tg number has not been negotiated and is unknown at
           this time."
      ::=  { ibmappnNodeLsStatusEntry 6 }
ibmappnNodeLsStatusGeneralSense OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The error sense code associated with the start sequence of
           activation of a link up to the beginning of the XID
           sequence."
      ::=  { ibmappnNodeLsStatusEntry 7 }
ibmappnNodeLsStatusNofRetry OBJECT-TYPE
      SYNTAX INTEGER    {
                          retry(1),
                          noretry(2)
                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Indicates whether Node Operator Facility will retry the
          start request to activate the link."
      ::=  { ibmappnNodeLsStatusEntry 8 }
ibmappnNodeLsStatusEndSense OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The sense code associated with the termination of the link
           connection to adjacent node.  This includes all sense
           information included in the disconnect recieved from the
           lower layer DLCs and also sense information indicating the
           link termination originated by upper layer APPN components."
      ::=  { ibmappnNodeLsStatusEntry 9 }
ibmappnNodeLsStatusXidLocalSense   OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The error sense code associated with the rejection of the

McKenzie & Cheng [Page 44] RFC 1593 SNA APPN Node MIB March 1994

           XID."
      ::=  { ibmappnNodeLsStatusEntry 10 }
ibmappnNodeLsStatusXidRemoteSense   OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The error sense code adjacent node returned to this node
           indicating the reason the XID was rejected."
      ::=  { ibmappnNodeLsStatusEntry 11 }
ibmappnNodeLsStatusXidByteInError      OBJECT-TYPE
      SYNTAX INTEGER    {
                         na(1000)
                        }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This identifies the actual byte in the XID that caused the
           error.  The value of zero (0) indicates that the variable
           has no meaning."
      ::=  { ibmappnNodeLsStatusEntry 12 }
ibmappnNodeLsStatusXidBitInError      OBJECT-TYPE
      SYNTAX INTEGER    {
                         na(8)   -- not applicable
                        }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This identifies the actual bit within the error byte of the
           XID.  This only has meaning when the byte in error is
           greater than zero."
      ::=  { ibmappnNodeLsStatusEntry 13 }
ibmappnNodeLsStatusDlcType  OBJECT-TYPE
      SYNTAX INTEGER    {
                         other(1),
                         sdlc(2),
                         dls(3),
                         socket(4),
                         ethernet(5),
                         tr(6)

McKenzie & Cheng [Page 45] RFC 1593 SNA APPN Node MIB March 1994

                         }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This identifies DLC type that was being used when error
           occurred.  This also is used to the format of the
           local and remote address provided.
           other    = free form DisplayString
           ip       = ld. ld. ld. ld / 2d
           tr       = lx: lx: lx: lx: lx: lx . lx
           dlsw     = lx: lx: lx: lx: lx: lx . lx
           ethernet = lx: lx: lx: lx: lx: lx . lx
           "
      ::=  { ibmappnNodeLsStatusEntry 14 }
ibmappnNodeLsStatusLocalAddr   OBJECT-TYPE
      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This contains a displayable string that identifies the
           DLC type and appropriate address.  See DlcType above for
           details of the format."
      ::=  { ibmappnNodeLsStatusEntry 15 }
ibmappnNodeLsStatusRemoteAddr  OBJECT-TYPE
      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "This contains a displayable string that identifies the
           DLC type and appropriate address.  See DlcType above for
           details of the format."
      ::=  { ibmappnNodeLsStatusEntry 16 }
  1. - – APPN SNMP Performance Information McKenzie & Cheng [Page 46] RFC 1593 SNA APPN Node MIB March 1994 – ibmappnSnmpInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of messages delivered to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 1 } ibmappnSnmpInGetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of GET requests delivered to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 2 } ibmappnSnmpInGetNexts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of GETNEXT requests delivered to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 3 } ibmappnSnmpInSetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of SET requests delivered to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 4 } ibmappnSnmpInTotalVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of VARIABLES included in both GET and GETNEXT requests to the APPN SNMP sub-agent." McKenzie & Cheng [Page 47] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnSnmpInformation 5 } ibmappnSnmpInGetVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of VARIBLES included in all GET requests to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 6 } ibmappnSnmpInGetNextVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of VARIABLES included in all GETNEXT requests to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 7 } ibmappnSnmpInSetVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of VARIBLES included in all SET requests to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 8 } ibmappnSnmpOutNoSuchNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of VARIABLES that could not be found by the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 9 } ibmappnSnmpOutGenErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of undefined errors that McKenzie & Cheng [Page 48] RFC 1593 SNA APPN Node MIB March 1994 occurred processing SNMP request to the APPN SNMP sub-agent." ::= { ibmappnSnmpInformation 10 } –
  1. - This group provides global information about the
  2. - APPN node performance.
  1. - The first section applies to the APPN control point
  2. - storage utilization.
ibmappnMemorySize OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Size of the shared storage segment, as obtained
            by storage management from the underlying operating
            system."
      ::=  { ibmappnMemoryUse 1 }
ibmappnMemoryUsed OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of bytes in the segment that are currently
            allocated to process."
      ::=  { ibmappnMemoryUse 2 }
ibmappnMemoryWarnThresh OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Allocation threshold beyond which storage
            management considers the storage resources
            to be constrained."
      ::=  { ibmappnMemoryUse 3 }
ibmappnMemoryCritThresh OBJECT-TYPE

McKenzie & Cheng [Page 49] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Allocation threshold beyond which storage
            management considers the storage resources
            to be critically constrained."
      ::=  { ibmappnMemoryUse 4 }
  1. - – The following are Counters maintained by the APPN CS component that – relate to total overall XID activity. ———————————————————————— ibmappnNodeDefLsGoodXids OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The current number of successfull XIDs that have occurred on all defined link stations since the last time this node was initialized." ::= { ibmappnXidInformation 1 } ibmappnNodeDefLsBadXids OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The current number of unsuccessfull XIDs that have occurred on all defined link stations since the last time this node was initialized." ::= { ibmappnXidInformation 2 } ibmappnNodeDynLsGoodXids OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The current number of successfull XIDs that have occurred on all dynamic link stations since the last time this node was initialized." ::= { ibmappnXidInformation 3 } McKenzie & Cheng [Page 50] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNodeDynLsBadXids OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The current number of unsuccessfull XIDs that have occurred on all dynamic link stations since the last time this node was initialized." ::= { ibmappnXidInformation 4 } – The APPN Topology Group * ibmappnNn OBJECT IDENTIFIER ::= { ibmappn 2 } ibmappnNnTopo OBJECT IDENTIFIER ::= { ibmappnNn 1 } ibmappnNnTopology OBJECT IDENTIFIER ::= { ibmappnNn 3 } – This group will be used to represent the entire APPN network – topology, including Network nodes, virtual nodes and – all TGs associated with these nodes. – – Network nodes – The APPN topology database consists of information about every – APPN network node. This information is learned over time – as each network node exchanges topology information with – each of its adjacent network nodes. The database consists – of information about each node and all of the transmissions – groups used by each node. – Virtual nodes – Information about virtual nodes (connection networks) is treated – the same as information about network node – and is replicated at each network node. – The node name is the only meaningful information. The other – node objects use default values. Each node that has defined – a TG with this virtual node as the destination also defines a – TG on this virtual node. There is a TG record for each node – that uses this virtual node. – – – The APPN node table represents the APPN topology – database with the APPN CP fully-qualified name – being used as the index to this table. – This entire table could be retrieved using the GET NEXT command, McKenzie & Cheng [Page 51] RFC 1593 SNA APPN Node MIB March 1994 – however, due to the dynamics of APPN, nodes could come and – go and status could change as the table is being – retrieved. Although in most cases the data retrieved will be valid, – missing and invalid status could cause problems for – a management application that was graphically displaying – this data. – This potential problem can be eliminated by – retrieving the FRSN before and after completion – of retrieval of the APPN topology table. – If the FRSN has changed, then repeat the – retrieval of the entire topology table – until the FRSN remains unchanged. – Object 'appnNnFrsn' represents the last – change or update to this node's topology – database. – – – The format of the actual database is as follows: – – Node table (entry for each node in network) – TG table (entry for each TG owned by node) – – Due to SNMP ASN.1 limitations, we cannot represent – the TG table within the node table. We define – separate tables for nodes and TGs, adding the node – name to each TG entry to provide a means of – correlating each TG with its originating node. ibmappnNnTopoMaxNodes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of nodes allowed in the APPN topology database. This administratively assigned value must be equal to or greater than the maximum total number of end nodes and network nodes. If the number of nodes exceeds this value, APPN will issue an Alert and the node can no longer participate as a network node." ::= { ibmappnNnTopo 1 } ibmappnNnTopoCurNumNodes OBJECT-TYPE SYNTAX Gauge ACCESS read-only McKenzie & Cheng [Page 52] RFC 1593 SNA APPN Node MIB March 1994 STATUS mandatory DESCRIPTION "Current number of nodes in this node's topology database. If this value exceeds the maximum number of nodes allowed (NnTopoMaxNodes), APPN alert CPDB002 is issued." ::= { ibmappnNnTopo 2 } ibmappnNnTopoInTdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of TDUs received from all adjacent NN since last initialization." ::= { ibmappnNnTopo 3 } ibmappnNnTopoOutTdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of TDUs built by this node to be sent to all adjacent NN since last initialization." ::= { ibmappnNnTopo 4 } ibmappnNnTopoNodeLowRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the adjacent node that sent this low RSN." ::= { ibmappnNnTopo 5 } ibmappnNnTopoNodeEqualRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only McKenzie & Cheng [Page 53] RFC 1593 SNA APPN Node MIB March 1994 STATUS mandatory DESCRIPTION "Total number of topology node updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs." ::= { ibmappnNnTopo 6 } ibmappnNnTopoNodeGoodHighRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes. It is not required to send a TDU to the sender of this update because that node already has the update." ::= { ibmappnNnTopo 7 } ibmappnNnTopoNodeBadHighRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node updates received by this node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes." ::= { ibmappnNnTopo 8 } ibmappnNnTopoNodeStateUpdates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology Node records built as a result McKenzie & Cheng [Page 54] RFC 1593 SNA APPN Node MIB March 1994 of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes." ::= { ibmappnNnTopo 9 } ibmappnNnTopoNodeErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs." ::= { ibmappnNnTopo 10 } ibmappnNnTopoNodeTimerUpdates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database." ::= { ibmappnNnTopo 11 } ibmappnNnTopoNodePurges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology node records purged from this node's topology database. This occurs when a node has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants kept in the network topology." ::= { ibmappnNnTopo 12 } ibmappnNnTopoTgLowRsns OBJECT-TYPE McKenzie & Cheng [Page 55] RFC 1593 SNA APPN Node MIB March 1994 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the sender of the low RSN." ::= { ibmappnNnTopo 13 } ibmappnNnTopoTgEqualRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs." ::= { ibmappnNnTopo 14 } ibmappnNnTopoTgGoodHighRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting the update to all adjacent network nodes." ::= { ibmappnNnTopo 15 } ibmappnNnTopoTgBadHighRsns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG updates received by this McKenzie & Cheng [Page 56] RFC 1593 SNA APPN Node MIB March 1994 node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes." ::= { ibmappnNnTopo 16 } ibmappnNnTopoTgStateUpdates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG records built as a result of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes." ::= { ibmappnNnTopo 17 } ibmappnNnTopoTgErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs." ::= { ibmappnNnTopo 18 } ibmappnNnTopoTgTimerUpdates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database." ::= { ibmappnNnTopo 19 } McKenzie & Cheng [Page 57] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnTopoTgPurges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of topology TG records purged from this node's topology database. This occurs when a TG has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants to keep in the network topology." ::= { ibmappnNnTopo 20 } ibmappnNnTopoTotalRouteCalcs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of routes calculated for all class of services since the last initialization." ::= { ibmappnNnTopo 21 } ibmappnNnTopoTotalRouteRejs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of route requests for all class of services that could not be calculated since last initialization." ::= { ibmappnNnTopo 22 } ibmappnNnTopoRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnTopoRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing an entry for every Class of Service that it has calculated a route for." ::= { ibmappnNnTopo 23 } ibmappnNnTopoRouteEntry OBJECT-TYPE McKenzie & Cheng [Page 58] RFC 1593 SNA APPN Node MIB March 1994 SYNTAX IbmappnNnTopoRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Class of Service name is the index for this table." INDEX {ibmappnNnTopoRouteCos} ::= { ibmappnNnTopoRouteTable 1 } IbmappnNnTopoRouteEntry ::= SEQUENCE { ibmappnNnTopoRouteCos DisplayString, ibmappnNnTopoRouteTrees Counter, ibmappnNnTopoRouteCalcs Counter, ibmappnNnTopoRouteRejs Counter } ibmappnNnTopoRouteCos OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Class of Service for the route." ::= { ibmappnNnTopoRouteEntry 1 } ibmappnNnTopoRouteTrees OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of routes tree caches built for this Class of Service since the last initialization." ::= { ibmappnNnTopoRouteEntry 2 } ibmappnNnTopoRouteCalcs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of routes calculated since last initialization." ::= { ibmappnNnTopoRouteEntry 3 } McKenzie & Cheng [Page 59] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnTopoRouteRejs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of route requests that could not be calculated since last initialization." ::= { ibmappnNnTopoRouteEntry 4 } –Adjacent node table – Node name (only applies to adjacent nodes) – Number of out of sequence TDUs – Status of CP-CP sessions (ConWinner/ConLoser) – Last FRSN sent – Last FRSN received ibmappnNnAdjNodeTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnAdjNodeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing an entry for every node. The information kept in this table is the last FRSN sent and received, the status of the CP-CP sessions, and a gauge that indicates the number of outstanding TDUs." ::= { ibmappnNn 2 } ibmappnNnAdjNodeEntry OBJECT-TYPE SYNTAX IbmappnNnAdjNodeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The adjacent node name is the index for this table." INDEX {ibmappnNnAdjNodeAdjName} ::= { ibmappnNnAdjNodeTable 1 } IbmappnNnAdjNodeEntry ::= SEQUENCE { ibmappnNnAdjNodeAdjName DisplayString, ibmappnNnAdjNodeCpCpSessStatus INTEGER, ibmappnNnAdjNodeOutOfSeqTdus Gauge, McKenzie & Cheng [Page 60] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnAdjNodeLastFrsnSent INTEGER, ibmappnNnAdjNodeLastFrsnRcvd INTEGER } ibmappnNnAdjNodeAdjName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "An administratively-assigned fully-qualified name of this node's adjacent network node." ::= { ibmappnNnAdjNodeEntry 1 } ibmappnNnAdjNodeCpCpSessStatus OBJECT-TYPE SYNTAX INTEGER { active(1), conLoserActive(2), conWinnerActive(3), inactive(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the state of CP-CP sessions between this node and adjacent network and end nodes. Incative indicates no CP-CP sessions exists between this node and the adjacent node. Active indicates CP-CP sessons are active using both the ConWinner and ConLoser sessions. The session initiated by this node is refered to as the ConWinner session and is used by this node to send to the adjacent node. The ConLoserr session is initiated by the adjacent node and is used by this node to receive from the adjacent node." ::= { ibmappnNnAdjNodeEntry 2 } ibmappnNnAdjNodeOutOfSeqTdus OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Number of out of sequence Topology Database Updates (TDUs). In a quiesced state, this value is zero. In normal operation, the value varies depending on the network environment." ::= { ibmappnNnAdjNodeEntry 3 } McKenzie & Cheng [Page 61] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnAdjNodeLastFrsnSent OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU sent to this adjacent node." ::= { ibmappnNnAdjNodeEntry 4 } ibmappnNnAdjNodeLastFrsnRcvd OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU received from this adjacent node." ::= { ibmappnNnAdjNodeEntry 5 } –APPN Node Topology table – This table describes every known APPN Network node – and Virtual node. ibmappnNnTopologyTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnTopologyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node." ::= { ibmappnNnTopology 1 } ibmappnNnTopologyEntry OBJECT-TYPE SYNTAX IbmappnNnTopologyEntry ACCESS not-accessible STATUS mandatory McKenzie & Cheng [Page 62] RFC 1593 SNA APPN Node MIB March 1994 DESCRIPTION "The fully-qualified node name is used to index this table." INDEX {ibmappnNnNodeName} ::= { ibmappnNnTopologyTable 1 } IbmappnNnTopologyEntry ::= SEQUENCE { ibmappnNnNodeName DisplayString, ibmappnNnNodeFrsn INTEGER, ibmappnNnNodeEntryTimeLeft INTEGER, ibmappnNnNodeType INTEGER, ibmappnNnNodeRsn INTEGER, ibmappnNnNodeRouteAddResist INTEGER, ibmappnNnNodeCongested INTEGER, ibmappnNnNodeIsrDepleted INTEGER, ibmappnNnNodeEndptDepleted INTEGER, ibmappnNnNodeQuiescing INTEGER, ibmappnNnNodeGateway INTEGER, ibmappnNnNodeCentralDirectory INTEGER, ibmappnNnNodeIsr INTEGER, ibmappnNnNodeChainSupport INTEGER } ibmappnNnNodeName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME." ::= { ibmappnNnTopologyEntry 1 } ibmappnNnNodeFrsn OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at McKenzie & Cheng [Page 63] RFC 1593 SNA APPN Node MIB March 1994 this node." ::= { ibmappnNnTopologyEntry 2 } ibmappnNnNodeEntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..31) ACCESS read-only STATUS mandatory DESCRIPTION "Number of days before deletion of this network node entry. Range is 0-31." ::= { ibmappnNnTopologyEntry 3 } ibmappnNnNodeType OBJECT-TYPE SYNTAX INTEGER { networknode(1), virtualnode(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of APPN node." ::= { ibmappnNnTopologyEntry 4 } ibmappnNnNodeRsn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred." ::= { ibmappnNnTopologyEntry 5 } ibmappnNnNodeRouteAddResist OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, McKenzie & Cheng [Page 64] RFC 1593 SNA APPN Node MIB March 1994 the more desirable the node is for intermediate routing." ::= { ibmappnNnTopologyEntry 6 } ibmappnNnNodeCongested OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists." ::= { ibmappnNnTopologyEntry 7 } ibmappnNnNodeIsrDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted." ::= { ibmappnNnTopologyEntry 8 } ibmappnNnNodeEndptDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether session endpoint resources are depleted." ::= { ibmappnNnTopologyEntry 9 } ibmappnNnNodeQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing." ::= { ibmappnNnTopologyEntry 10 } ibmappnNnNodeGateway OBJECT-TYPE McKenzie & Cheng [Page 65] RFC 1593 SNA APPN Node MIB March 1994 SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node provide gateway functions." ::= { ibmappnNnTopologyEntry 11 } ibmappnNnNodeCentralDirectory OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node is central directory." ::= { ibmappnNnTopologyEntry 12 } ibmappnNnNodeIsr OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node supports intermediate session routing (ISR)." ::= { ibmappnNnTopologyEntry 13 } ibmappnNnNodeChainSupport OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node supports chaining." ::= { ibmappnNnTopologyEntry 14 } –APPN transmission group (TG) table – This table describes the TGs associated with – the APPN network nodes. – The originating node is repeated here to provide a – means of correlating the TGs with the nodes. ibmappnNnTgTopologyTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnTgTopologyEntry ACCESS not-accessible McKenzie & Cheng [Page 66] RFC 1593 SNA APPN Node MIB March 1994 STATUS mandatory DESCRIPTION "Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes." ::= { ibmappnNnTopology 2 } ibmappnNnTgTopologyEntry OBJECT-TYPE SYNTAX IbmappnNnTgTopologyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table requires three indexes to provide a unique index. The indexes are the owning or originating CPname, the destination CPname, and the TG number." INDEX {ibmappnNnTgOwner, ibmappnNnTgDest, ibmappnNnTgNum} ::= { ibmappnNnTgTopologyTable 1 } IbmappnNnTgTopologyEntry ::= SEQUENCE { ibmappnNnTgOwner DisplayString, ibmappnNnTgDest DisplayString, ibmappnNnTgNum INTEGER, ibmappnNnTgFrsn INTEGER, ibmappnNnTgEntryTimeLeft INTEGER, ibmappnNnTgDestVirtual INTEGER, ibmappnNnTgDlcData OCTET STRING, ibmappnNnTgRsn INTEGER, ibmappnNnTgOperational INTEGER, ibmappnNnTgQuiescing INTEGER, ibmappnNnTgCpCpSession INTEGER, ibmappnNnTgEffCap INTEGER, ibmappnNnTgConnCost INTEGER, ibmappnNnTgByteCost INTEGER, ibmappnNnTgSecurity INTEGER, ibmappnNnTgDelay INTEGER, ibmappnNnTgModemClass INTEGER, ibmappnNnTgUsr1 INTEGER, ibmappnNnTgUsr2 INTEGER, ibmappnNnTgUsr3 INTEGER} McKenzie & Cheng [Page 67] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnTgOwner OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table." ::= { ibmappnNnTgTopologyEntry 1 } ibmappnNnTgDest OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned fully-qualified network name for the destination node for this TG." ::= { ibmappnNnTgTopologyEntry 2 } ibmappnNnTgNum OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number associated with this transmission group. Range is 0-255." ::= { ibmappnNnTgTopologyEntry 3 } ibmappnNnTgFrsn OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node." ::= { ibmappnNnTgTopologyEntry 4 } ibmappnNnTgEntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..31) McKenzie & Cheng [Page 68] RFC 1593 SNA APPN Node MIB March 1994 ACCESS read-only STATUS mandatory DESCRIPTION "Number of days before deletion of this network node TG entry. Range is 0-31." ::= { ibmappnNnTgTopologyEntry 5 } ibmappnNnTgDestVirtual OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the destination node is a virtual node." ::= { ibmappnNnTgTopologyEntry 6 } ibmappnNnTgDlcData OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) ACCESS read-only STATUS mandatory DESCRIPTION "DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits" ::= { ibmappnNnTgTopologyEntry 7 } ibmappnNnTgRsn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current owning node's resource sequence number for this resource." ::= { ibmappnNnTgTopologyEntry 8 } ibmappnNnTgOperational OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the transmission group McKenzie & Cheng [Page 69] RFC 1593 SNA APPN Node MIB March 1994 is operational." ::= { ibmappnNnTgTopologyEntry 9 } ibmappnNnTgQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the transmission group is quiescing." ::= { ibmappnNnTgTopologyEntry 10 } ibmappnNnTgCpCpSession OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether CP-CP sessions are supported on this TG." ::= { ibmappnNnTgTopologyEntry 11 } ibmappnNnTgEffCap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 12 } ibmappnNnTgConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated McKenzie & Cheng [Page 70] RFC 1593 SNA APPN Node MIB March 1994 with this TG." ::= { ibmappnNnTgTopologyEntry 13 } ibmappnNnTgByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 14 } ibmappnNnTgSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), –X'01' publicSwitchedNetwork(32), –X'20' undergroundCable(64), –X'40' secureConduit(96), –X'60' guardedConduit(128), –X'80' encrypted(160), –X'A0' guardedRadiation(192) –X'C0' } ACCESS read-only STATUS mandatory DESCRIPTION "The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 15 } ibmappnNnTgDelay OBJECT-TYPE SYNTAX INTEGER { minimum(0), –X'00' negligible(384), –X'4C' terrestrial(9216), –X'71' packet(147456), –X'91' long(294912), –X'99' maximum(2013265920) –X'FF' } ACCESS read-only McKenzie & Cheng [Page 71] RFC 1593 SNA APPN Node MIB March 1994 STATUS mandatory DESCRIPTION "Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 16 } ibmappnNnTgModemClass OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'." ::= { ibmappnNnTgTopologyEntry 17 } ibmappnNnTgUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 18 } ibmappnNnTgUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 19 } McKenzie & Cheng [Page 72] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnTgUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyEntry 20 } –APPN Node Topology table (using FRSN as index) – This table describes every known APPN Network node – and Virtual node. ibmappnNnTopologyFRTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnTopologyFREntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node." ::= { ibmappnNnTopology 3 } ibmappnNnTopologyFREntry OBJECT-TYPE SYNTAX IbmappnNnTopologyFREntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is indexed by two columns: FRSN, followed by fully-qualified node name." INDEX {ibmappnNnNodeFRFrsn, ibmappnNnNodeFRName} ::= { ibmappnNnTopologyFRTable 1 } IbmappnNnTopologyFREntry ::= SEQUENCE { ibmappnNnNodeFRName DisplayString, ibmappnNnNodeFRFrsn INTEGER, ibmappnNnNodeFREntryTimeLeft INTEGER, McKenzie & Cheng [Page 73] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnNodeFRType INTEGER, ibmappnNnNodeFRRsn INTEGER, ibmappnNnNodeFRRouteAddResist INTEGER, ibmappnNnNodeFRCongested INTEGER, ibmappnNnNodeFRIsrDepleted INTEGER, ibmappnNnNodeFREndptDepleted INTEGER, ibmappnNnNodeFRQuiescing INTEGER, ibmappnNnNodeFRGateway INTEGER, ibmappnNnNodeFRCentralDirectory INTEGER, ibmappnNnNodeFRIsr INTEGER, ibmappnNnNodeFRChainSupport INTEGER } ibmappnNnNodeFRName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME." ::= { ibmappnNnTopologyFREntry 1 } ibmappnNnNodeFRFrsn OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node." ::= { ibmappnNnTopologyFREntry 2 } ibmappnNnNodeFREntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..31) ACCESS read-only STATUS mandatory DESCRIPTION "Number of days before deletion of this network node entry. Range is 0-31." ::= { ibmappnNnTopologyFREntry 3 } McKenzie & Cheng [Page 74] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnNodeFRType OBJECT-TYPE SYNTAX INTEGER { networknode(1), virtualnode(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of APPN node." ::= { ibmappnNnTopologyFREntry 4 } ibmappnNnNodeFRRsn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred." ::= { ibmappnNnTopologyFREntry 5 } ibmappnNnNodeFRRouteAddResist OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing." ::= { ibmappnNnTopologyFREntry 6 } ibmappnNnNodeFRCongested OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists." ::= { ibmappnNnTopologyFREntry 7 } McKenzie & Cheng [Page 75] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnNodeFRIsrDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted." ::= { ibmappnNnTopologyFREntry 8 } ibmappnNnNodeFREndptDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether session endpoint resources are depleted." ::= { ibmappnNnTopologyFREntry 9 } ibmappnNnNodeFRQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing." ::= { ibmappnNnTopologyFREntry 10 } ibmappnNnNodeFRGateway OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node provide gateway functions." ::= { ibmappnNnTopologyFREntry 11 } ibmappnNnNodeFRCentralDirectory OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node is central directory." ::= { ibmappnNnTopologyFREntry 12 } McKenzie & Cheng [Page 76] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnNodeFRIsr OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node supports intermediate session routing (ISR)." ::= { ibmappnNnTopologyFREntry 13 } ibmappnNnNodeFRChainSupport OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the node supports chaining." ::= { ibmappnNnTopologyFREntry 14 } –APPN transmission group (TG) table – This table describes the TGs associated with – the APPN network nodes. – The originating node is repeated here to provide a – means of correlating the TGs with the nodes. ibmappnNnTgTopologyFRTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnNnTgTopologyFREntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes." ::= { ibmappnNnTopology 4 } ibmappnNnTgTopologyFREntry OBJECT-TYPE SYNTAX IbmappnNnTgTopologyFREntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is indexed by four columns: FRSN, TG owner fully-qualified node name, TG destination fully-qualified node name, and TG number." INDEX McKenzie & Cheng [Page 77] RFC 1593 SNA APPN Node MIB March 1994 {ibmappnNnTgFRFrsn, ibmappnNnTgFROwner, ibmappnNnTgFRDest, ibmappnNnTgFRNum} ::= { ibmappnNnTgTopologyFRTable 1 } IbmappnNnTgTopologyFREntry ::= SEQUENCE { ibmappnNnTgFROwner DisplayString, ibmappnNnTgFRDest DisplayString, ibmappnNnTgFRNum INTEGER, ibmappnNnTgFRFrsn INTEGER, ibmappnNnTgFREntryTimeLeft INTEGER, ibmappnNnTgFRDestVirtual INTEGER, ibmappnNnTgFRDlcData OCTET STRING, ibmappnNnTgFRRsn INTEGER, ibmappnNnTgFROperational INTEGER, ibmappnNnTgFRQuiescing INTEGER, ibmappnNnTgFRCpCpSession INTEGER, ibmappnNnTgFREffCap INTEGER, ibmappnNnTgFRConnCost INTEGER, ibmappnNnTgFRByteCost INTEGER, ibmappnNnTgFRSecurity INTEGER, ibmappnNnTgFRDelay INTEGER, ibmappnNnTgFRModemClass INTEGER, ibmappnNnTgFRUsr1 INTEGER, ibmappnNnTgFRUsr2 INTEGER, ibmappnNnTgFRUsr3 INTEGER} ibmappnNnTgFROwner OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table." ::= { ibmappnNnTgTopologyFREntry 1 } ibmappnNnTgFRDest OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) ACCESS read-only McKenzie & Cheng [Page 78] RFC 1593 SNA APPN Node MIB March 1994 STATUS mandatory DESCRIPTION "Administratively-assigned fully-qualified network name for the destination node for this TG." ::= { ibmappnNnTgTopologyFREntry 2 } ibmappnNnTgFRNum OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number associated with this transmission group. Range is 0-255." ::= { ibmappnNnTgTopologyFREntry 3 } ibmappnNnTgFRFrsn OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node." ::= { ibmappnNnTgTopologyFREntry 4 } ibmappnNnTgFREntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..31) ACCESS read-only STATUS mandatory DESCRIPTION "Number of days before deletion of this network node TG entry. Range is 0-31." ::= { ibmappnNnTgTopologyFREntry 5 } ibmappnNnTgFRDestVirtual OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the destination node is a virtual node." McKenzie & Cheng [Page 79] RFC 1593 SNA APPN Node MIB March 1994 ::= { ibmappnNnTgTopologyFREntry 6 } ibmappnNnTgFRDlcData OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) ACCESS read-only STATUS mandatory DESCRIPTION "DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits" ::= { ibmappnNnTgTopologyFREntry 7 } ibmappnNnTgFRRsn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current owning node's resource sequence number for this resource." ::= { ibmappnNnTgTopologyFREntry 8 } ibmappnNnTgFROperational OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the transmission group is operational." ::= { ibmappnNnTgTopologyFREntry 9 } ibmappnNnTgFRQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the transmission group is quiescing." ::= { ibmappnNnTgTopologyFREntry 10 } ibmappnNnTgFRCpCpSession OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} McKenzie & Cheng [Page 80] RFC 1593 SNA APPN Node MIB March 1994 ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether CP-CP sessions are supported on this TG." ::= { ibmappnNnTgTopologyFREntry 11 } ibmappnNnTgFREffCap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 12 } ibmappnNnTgFRConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 13 } ibmappnNnTgFRByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 14 } McKenzie & Cheng [Page 81] RFC 1593 SNA APPN Node MIB March 1994 ibmappnNnTgFRSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), –X'01' publicSwitchedNetwork(32), –X'20' undergroundCable(64), –X'40' secureConduit(96), –X'60' guardedConduit(128), –X'80' encrypted(160), –X'A0' guardedRadiation(192) –X'C0' } ACCESS read-only STATUS mandatory DESCRIPTION "The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 15 } ibmappnNnTgFRDelay OBJECT-TYPE SYNTAX INTEGER { minimum(0), –X'00' negligible(384), –X'4C' terrestrial(9216), –X'71' packet(147456), –X'91' long(294912), –X'99' maximum(2013265920) –X'FF' } ACCESS read-only STATUS mandatory DESCRIPTION "Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 16 } ibmappnNnTgFRModemClass OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This is used to have multiple images for a McKenzie & Cheng [Page 82] RFC 1593 SNA APPN Node MIB March 1994 connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'." ::= { ibmappnNnTgTopologyFREntry 17 } ibmappnNnTgFRUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 18 } ibmappnNnTgFRUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 19 } ibmappnNnTgFRUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG." ::= { ibmappnNnTgTopologyFREntry 20 } – The APPN Local Topology Group *
ibmappnLocalTopology   OBJECT IDENTIFIER ::= { ibmappn 3 }
ibmappnLocalThisNode   OBJECT IDENTIFIER ::= { ibmappnLocalTopology 1 }
ibmappnLocalGeneral    OBJECT IDENTIFIER ::= { ibmappnLocalThisNode   1}

McKenzie & Cheng [Page 83] RFC 1593 SNA APPN Node MIB March 1994

ibmappnLocalNnSpecific OBJECT IDENTIFIER ::= { ibmappnLocalThisNode   2}
ibmappnLocalTg         OBJECT IDENTIFIER ::= { ibmappnLocalThisNode   3}
ibmappnLocalEnTopology OBJECT IDENTIFIER ::= { ibmappnLocalTopology 2 }
  1. - The LocalEnNodeTable and LocalEnTgTable will replace these OIs
  2. -ibmappnLocalEnNode OBJECT IDENTIFIER ::= { ibmappnLocalEnTopology 1}
  3. -ibmappnLocalEnTg OBJECT IDENTIFIER ::= { ibmappnLocalEnTopology 2}
  1. -This MIB Group represents the local topology
  2. -maintained in both APPN end nodes and network nodes.
  3. -Although the same control vectors are used for both network
  4. -and local topology, many of the attributes only apply to network
  5. -nodes. This MIB group defines the required objects for retrieval
  6. -of information about this node and the objects that represent
  7. -the local topology about end nodes.
  8. -
  9. -This node could be either an network node or an end node. The
  10. -definition must address both cases.
  11. -
  12. -1 Information about this node
  13. - a General information about this node, both NN and ENs.
  14. - b Information about this node that applies only to NNs.
  15. - c TG table (repeated for each TG this node owns)
  16. -
  17. -2 Information about the end nodes known to this network node
  18. - (THIS SECTION ONLY APPLIES TO NETWORK NODES)
  19. - a End node table (entry for each end node )
  20. - b TG table (repeated for each TG owned by the end nodes)
  21. -
  22. -
  1. - General information section
ibmappnLocalNodeName    OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned fully-qualified name
          for this node. Format is NETID.CPNAME."
      ::=  { ibmappnLocalGeneral 1 }
ibmappnLocalNodeType    OBJECT-TYPE

McKenzie & Cheng [Page 84] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX INTEGER {
                     networknode(1),
                     endnode(2),
                     len(4)
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Type of APPN node."
      ::=  { ibmappnLocalGeneral 2 }
  1. - Network node unique information
  2. -
ibmappnLocalNnRsn       OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Resource sequence number is assigned and
            controlled by the network node that owns this
            resource.  This is always an even unsigned
            number unless an error has occurred."
      ::=  { ibmappnLocalNnSpecific  1 }
ibmappnLocalNnRouteAddResist   OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Route addition resistance
          indicates the relative desirability
          of using this node for intermediate session traffic.
          The value, which can be any integer 0-255,
          is used in route computation.  The lower the value,
          the more desirable the node is for intermediate routing."
      ::=  { ibmappnLocalNnSpecific 2 }
ibmappnLocalNnCongested        OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether this node is congested.

McKenzie & Cheng [Page 85] RFC 1593 SNA APPN Node MIB March 1994

            Other network nodes stop routing traffic to
            this node while this flag is on."
       ::= { ibmappnLocalNnSpecific 3 }
ibmappnLocalNnIsrDepleted OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicate whether intermediated session
            routing resources are depleted.
            Other network nodes stop routing traffic through
            this node while this flag is on."
      ::=  { ibmappnLocalNnSpecific 4 }
ibmappnLocalNnEndptDepleted OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether session endpoint resources
            are depleted."
      ::=  { ibmappnLocalNnSpecific 5 }
ibmappnLocalNnQuiescing     OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node is quiescing."
      ::=  { ibmappnLocalNnSpecific 6 }
ibmappnLocalNnGateway       OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node is a gateway."
      ::=  { ibmappnLocalNnSpecific 7 }
ibmappnLocalNnCentralDirectory OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only

McKenzie & Cheng [Page 86] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node is a central directory."
      ::=  { ibmappnLocalNnSpecific 8 }
ibmappnLocalNnIsr   OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node supports intermediate
            session routing."
      ::=  { ibmappnLocalNnSpecific 9 }
ibmappnLocalNnChainSupport OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the node supports chaining."
      ::=  { ibmappnLocalNnSpecific 10 }
ibmappnLocalNnFrsn     OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Flow reduction sequence numbers (FRSNs) are associated
           with Topology Database Updates (TDUs) and are unique
           only within each APPN network node.  A TDU can be
           associated with multiple APPN resources. This object
           is the last FRSN sent in a topology update to
           adjacent network nodes."
      ::=  { ibmappnLocalNnSpecific 11 }
  1. - Local TG information
  2. - APPN Transmission Group (TG) Table
  1. - This table describes the TGs associated with
  2. - this node only.
ibmappnLocalTgTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnLocalTgEntry

McKenzie & Cheng [Page 87] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "TG Table describes all of the TGs owned by this
            node.  The TG destination can be a virtual
            node, network node, len, or end node."
      ::= { ibmappnLocalTg 1 }
ibmappnLocalTgEntry OBJECT-TYPE
      SYNTAX IbmappnLocalTgEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table is indexed by the destination CPname
            and the TG number."
      INDEX
             {ibmappnLocalTgDest,
              ibmappnLocalTgNum}
      ::= { ibmappnLocalTgTable 1 }
IbmappnLocalTgEntry ::= SEQUENCE {
      ibmappnLocalTgDest       DisplayString,
      ibmappnLocalTgNum        INTEGER,
      ibmappnLocalTgDestVirtual INTEGER,
      ibmappnLocalTgDlcData    OCTET STRING,
      ibmappnLocalTgRsn        INTEGER,
      ibmappnLocalTgQuiescing  INTEGER,
      ibmappnLocalTgOperational INTEGER,
      ibmappnLocalTgCpCpSession INTEGER,
      ibmappnLocalTgEffCap     INTEGER,
      ibmappnLocalTgConnCost   INTEGER,
      ibmappnLocalTgByteCost   INTEGER,
      ibmappnLocalTgSecurity   INTEGER,
      ibmappnLocalTgDelay      INTEGER,
      ibmappnLocalTgModemClass INTEGER,
      ibmappnLocalTgUsr1       INTEGER,
      ibmappnLocalTgUsr2       INTEGER,
      ibmappnLocalTgUsr3       INTEGER
                                   }
ibmappnLocalTgDest  OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only

McKenzie & Cheng [Page 88] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
           "Administratively-assigned name for the
           destination node for this TG.
           This is the fully-qualified network node
           name."
      ::=  { ibmappnLocalTgEntry 1 }
ibmappnLocalTgNum  OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number associated with this transmission group."
      ::=  { ibmappnLocalTgEntry 2 }
ibmappnLocalTgDestVirtual  OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the destination node is
           a Virtual node."
      ::=  { ibmappnLocalTgEntry 3 }
ibmappnLocalTgDlcData  OBJECT-TYPE
      SYNTAX OCTET STRING  (SIZE (0..9))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "DLC specific data related to the link connection
           network.
           Token-Ring    - MAC/SAP
           X.25 Switched - dial digits
           X.21 Switched - dial digits
           Circuit Swtch - dial digits"
      ::=  { ibmappnLocalTgEntry 4 }
ibmappnLocalTgRsn       OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "The resource sequence number is assigned and
            controlled by the network node that owns this

McKenzie & Cheng [Page 89] RFC 1593 SNA APPN Node MIB March 1994

            resource.  This is always an even unsigned
            number unless an error has occurred."
      ::=  { ibmappnLocalTgEntry 5 }
ibmappnLocalTgQuiescing OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the Transmission Group
           is quiescing."
      ::=  { ibmappnLocalTgEntry 6 }
ibmappnLocalTgOperational OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the Transmission Group
           is operational."
      ::=  { ibmappnLocalTgEntry 7 }
ibmappnLocalTgCpCpSession OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the CP-CP Sessions are
           supported on this TG."
      ::=  { ibmappnLocalTgEntry 8 }
ibmappnLocalTgEffCap   OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The effective capacity is an integer value that indicates
           the actual kilo bits per second.
           It is derived from the link bandwidth and maximum load
           factor with the range of 0 thru 603,979,776."
      ::=  { ibmappnLocalTgEntry 9 }
ibmappnLocalTgConnCost OBJECT-TYPE

McKenzie & Cheng [Page 90] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Cost per connect time: a value representing
           the relative cost per unit of time to use
           the TG. Range is from 0, which means no cost,
           to 255."
      ::=  { ibmappnLocalTgEntry 10 }
ibmappnLocalTgByteCost  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Relative cost of transmitting a byte over this link.
          Range is from 0 (lowest cost) to 255."
      ::=  { ibmappnLocalTgEntry 11 }
ibmappnLocalTgSecurity  OBJECT-TYPE
      SYNTAX INTEGER {
                     nonsecure(1),                --X'01'
                     publicSwitchedNetwork(32),   --X'20'
                     undergroundCable(64),        --X'40'
                     secureConduit(96),           --X'60'
                     guardedConduit(128),         --X'80'
                     encrypted(160),              --X'A0'
                     guardedRadiation(192)        --X'C0'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Security level for this TG."
      ::=  { ibmappnLocalTgEntry 12 }
ibmappnLocalTgDelay  OBJECT-TYPE
      SYNTAX INTEGER {
                     minimum(0),                 --X'00'
                     negligible(384),            --X'4C'
                     terrestrial(9216),          --X'71'
                     packet(147456),             --X'91'
                     long(294912),               --X'99'
                     maximum(2013265920)         --X'FF'
             }
      ACCESS read-only

McKenzie & Cheng [Page 91] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
           "Relative amount of time that it takes for a signal to
            travel the length of the logical link.  This time is
            represented in micro seconds, with some of the more
            common values enumerated."
      ::=  { ibmappnLocalTgEntry 13 }
ibmappnLocalTgModemClass  OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "This is used to have multiple images for a
            connection network.  For a connection network
            it is the same as in the TG vector and for
            a non-connection network it is zero."
      ::=  { ibmappnLocalTgEntry 14 }
ibmappnLocalTgUsr1  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Value of the first user-defined TG
          characteristic for this TG.
          Range is 0-255."
      ::=  { ibmappnLocalTgEntry 15 }
ibmappnLocalTgUsr2  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Value of the second user-defined TG
          characteristic for this TG.
          Range is 0-255."
      ::=  { ibmappnLocalTgEntry 16 }
ibmappnLocalTgUsr3  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION

McKenzie & Cheng [Page 92] RFC 1593 SNA APPN Node MIB March 1994

          "Value of the third user-defined TG
          characteristic for this TG.
          Range is 0-255."
      ::=  { ibmappnLocalTgEntry 17 }
  1. - This section applies only to network nodes.
  2. - It contains end node topology information known to serving
  3. - network node.
  4. - The first table contains information about all end nodes
  5. - known to this node.
  6. -
  7. - The TG table contains information about all of the TGs owned
  8. - by these end nodes.
ibmappnLocalEnTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnLocalEnEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Portion of the APPN topology
            database that describes the end
            nodes known to this node."
      ::= { ibmappnLocalEnTopology 1 }
ibmappnLocalEnEntry OBJECT-TYPE
      SYNTAX IbmappnLocalEnEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table is indexed by the end node CPname."
      INDEX
             {ibmappnLocalEnName}
      ::= { ibmappnLocalEnTable 1 }
IbmappnLocalEnEntry ::= SEQUENCE {
      ibmappnLocalEnName                     DisplayString,
      ibmappnLocalEnEntryTimeLeft            INTEGER,
      ibmappnLocalEnType                     INTEGER
                          }
ibmappnLocalEnName    OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))

McKenzie & Cheng [Page 93] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned fully-qualified
          name of end node in the format NETID.CPNAME."
      ::=  { ibmappnLocalEnEntry 1 }
ibmappnLocalEnEntryTimeLeft   OBJECT-TYPE
      SYNTAX INTEGER (0..31)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Number of days before deletion of this
           end node entry. Range is 0-31."
      ::=  { ibmappnLocalEnEntry 2 }
ibmappnLocalEnType    OBJECT-TYPE
      SYNTAX INTEGER {
                     endnode(2),
                     len(4)
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Type of APPN node (must always be a len or end node)."
      ::=  { ibmappnLocalEnEntry 3 }
  1. -APPN Local End node Transmission Group (TG) table
  1. - This table describes the TGs associated with
  2. - all of the end nodes known to this node.
ibmappnLocalEnTgTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnLocalEnTgEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Table describing all of the TGs owned by the
            end nodes known to this node.
            The TG destination can be a virtual
            node, network node, or end node."
      ::= { ibmappnLocalEnTopology 2 }

McKenzie & Cheng [Page 94] RFC 1593 SNA APPN Node MIB March 1994

ibmappnLocalEnTgEntry OBJECT-TYPE
      SYNTAX IbmappnLocalEnTgEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table requires multiple indexes to uniquely
            identify each TG. They are originating CPname,
            destination CPname, and the TG number."
      INDEX
             {ibmappnLocalEnTgOrigin,
              ibmappnLocalEnTgDest,
              ibmappnLocalEnTgNum}
      ::= { ibmappnLocalEnTgTable 1 }
IbmappnLocalEnTgEntry ::= SEQUENCE {
      ibmappnLocalEnTgOrigin     DisplayString,
      ibmappnLocalEnTgDest       DisplayString,
      ibmappnLocalEnTgNum        INTEGER,
      ibmappnLocalEnTgEntryTimeLeft INTEGER,
      ibmappnLocalEnTgDestVirtual INTEGER,
      ibmappnLocalEnTgDlcData    OCTET STRING,
      ibmappnLocalEnTgOperational INTEGER,
      ibmappnLocalEnTgCpCpSession INTEGER,
      ibmappnLocalEnTgEffCap     INTEGER,
      ibmappnLocalEnTgConnCost   INTEGER,
      ibmappnLocalEnTgByteCost   INTEGER,
      ibmappnLocalEnTgSecurity   INTEGER,
      ibmappnLocalEnTgDelay      INTEGER,
      ibmappnLocalEnTgModemClass INTEGER,
      ibmappnLocalEnTgUsr1       INTEGER,
      ibmappnLocalEnTgUsr2       INTEGER,
      ibmappnLocalEnTgUsr3       INTEGER
                                    }
ibmappnLocalEnTgOrigin      OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for the
           origination node for this TG.
           This is the fully-qualified network name."
      ::=  { ibmappnLocalEnTgEntry 1 }

McKenzie & Cheng [Page 95] RFC 1593 SNA APPN Node MIB March 1994

ibmappnLocalEnTgDest        OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for the
           destination node for this TG.
           This is the fully-qualified network name."
      ::=  { ibmappnLocalEnTgEntry 2 }
ibmappnLocalEnTgNum  OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number associated with this transmission group."
      ::=  { ibmappnLocalEnTgEntry 3 }
ibmappnLocalEnTgEntryTimeLeft   OBJECT-TYPE
      SYNTAX INTEGER (0..31)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Number of days before deletion of this
           end node TG entry. Range is 0-31."
      ::=  { ibmappnLocalEnTgEntry 4 }
ibmappnLocalEnTgDestVirtual  OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the destination node is
           a virtual node."
      ::=  { ibmappnLocalEnTgEntry 5 }
ibmappnLocalEnTgDlcData  OBJECT-TYPE
      SYNTAX OCTET STRING
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "DLC specific data related to the link connection
           network.
           Token-Ring    - MAC/SAP

McKenzie & Cheng [Page 96] RFC 1593 SNA APPN Node MIB March 1994

           X.25 Switched - dial digits
           X.21 Switched - dial digits
           Circuit Swtch - dial digits"
      ::=  { ibmappnLocalEnTgEntry 6 }
ibmappnLocalEnTgOperational OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether the Transmission Group is operational."
      ::=  { ibmappnLocalEnTgEntry 7 }
ibmappnLocalEnTgCpCpSession OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Indicates whether CP-CP sessions are supported on this TG."
      ::=  { ibmappnLocalEnTgEntry 8 }
ibmappnLocalEnTgEffCap   OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The effective capacity is an integer value that indicates
           the actual kilo bits per second.
           It is derived from the link bandwidth and maximum load
           factor with the range of 0 thru 603,979,776."
      ::=  { ibmappnLocalEnTgEntry 9 }
ibmappnLocalEnTgConnCost OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Cost per connect time: a value representing
           the relative cost per unit of time to use
           the TG. Range is from 0, which means no cost,
           to 255."
      ::=  { ibmappnLocalEnTgEntry 10 }

McKenzie & Cheng [Page 97] RFC 1593 SNA APPN Node MIB March 1994

ibmappnLocalEnTgByteCost  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Relative cost of transmitting a byte over this link.
          Range is from 0, which means no cost, to 255."
      ::=  { ibmappnLocalEnTgEntry 11 }
ibmappnLocalEnTgSecurity  OBJECT-TYPE
      SYNTAX INTEGER {
                     nonsecure(1),                --X'01'
                     publicSwitchedNetwork(32),   --X'20'
                     undergroundCable(64),        --X'40'
                     secureConduit(96),           --X'60'
                     guardedConduit(128),         --X'80'
                     encrypted(160),              --X'A0'
                     guardedRadiation(192)        --X'C0'
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Security level for this TG."
      ::=  { ibmappnLocalEnTgEntry 12 }
ibmappnLocalEnTgDelay  OBJECT-TYPE
      SYNTAX INTEGER {
                     minimum(0),                 --X'00'
                     negligible(384),            --X'4C'
                     terrestrial(9216),          --X'71'
                     packet(147456),             --X'91'
                     long(294912),               --X'99'
                     maximum(2013265920)         --X'FF'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Relative amount of time that it takes for a signal to
            travel the length of the logical link.  This time is
            represented in micro seconds, with some of the more
            common values enumerated."
      ::=  { ibmappnLocalEnTgEntry 13 }
ibmappnLocalEnTgModemClass  OBJECT-TYPE
      SYNTAX INTEGER (0..65535)

McKenzie & Cheng [Page 98] RFC 1593 SNA APPN Node MIB March 1994

      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "This is used to have multiple images for a
            connection network.  For a connection network
            it is the same as in the TG vector and for
             a non connection network it is zero."
      ::=  { ibmappnLocalEnTgEntry 14 }
ibmappnLocalEnTgUsr1  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "First user-defined TG characteristic
          for this TG. Range of values is 0-255."
      ::=  { ibmappnLocalEnTgEntry 15 }
ibmappnLocalEnTgUsr2  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Second user-defined TG characteristic
           for this TG. Range of values is 0-255."
      ::=  { ibmappnLocalEnTgEntry 16 }
ibmappnLocalEnTgUsr3  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Third user-defined TG characteristic
           for this TG. Range of values is 0-255."
      ::=  { ibmappnLocalEnTgEntry 17 }
  1. - The APPN Directory group

ibmappnDir OBJECT IDENTIFIER ::= { ibmappn 5 }

ibmappnDirPerf  OBJECT IDENTIFIER ::= { ibmappnDir 1 }
  1. - The APPN Directory Group
  1. - The APPN Directory Database

McKenzie & Cheng [Page 99] RFC 1593 SNA APPN Node MIB March 1994

  1. - Each APPN network node maintains directories containing
  2. - information on which LUs (applications) are available and
  3. - where they are located. LUs can be located within an APPN
  4. - network node or in any of the attached end nodes.
  1. - Max Cache Directory Entries
  2. - Current Number of Cache Entries
  3. - Current Number Home Entries
  4. - Current Number of Registered Entries
  5. - number of directed locates sent
  6. - number of directed locates received
  7. - number of broadcast locates sent
  8. - number of broadcast locates received
  9. - Number of locates returned with a found
  10. - Number of locates returned with a not found
  11. - Number of outstanding Locates
  12. - Directory table (Repeated for each Serving NN)
  1. - Serving Network Node Fully Qualified CP Name
  1. - LU Groups within Directory table (one for each LU)
  1. - Fully-qualified LU Name
  2. - Owning fully-qualified CP Name
  3. - TP Name
  4. - Resource location (local/domain/cross-domain)
  5. - Entry type (home,Register/cache)
  6. - Wildcard (yes/no)
ibmappnDirMaxCaches OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Maximum number of cache entries allowed. This
           is an administratively assigned value."
      ::=  { ibmappnDirPerf 1 }
ibmappnDirCurCaches OBJECT-TYPE
      SYNTAX Gauge
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Current number of cache entries."
      ::=  { ibmappnDirPerf 2 }

McKenzie & Cheng [Page 100] RFC 1593 SNA APPN Node MIB March 1994

ibmappnDirCurHomeEntries  OBJECT-TYPE
      SYNTAX Gauge
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Current number of home entries."
      ::=  { ibmappnDirPerf 3 }
ibmappnDirRegEntries OBJECT-TYPE
      SYNTAX Gauge
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Current number of registered entries."
      ::=  { ibmappnDirPerf 4 }
ibmappnDirInLocates    OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of directed locates received."
      ::=  { ibmappnDirPerf 5 }
ibmappnDirInBcastLocates  OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of broadcast locates received."
      ::=  { ibmappnDirPerf 6 }
ibmappnDirOutLocates   OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of directed locates sent."
      ::=  { ibmappnDirPerf 7 }
ibmappnDirOutBcastLocates   OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only

McKenzie & Cheng [Page 101] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
           "Number of broadcast locates sent."
      ::=  { ibmappnDirPerf 8 }
ibmappnDirNotFoundLocates   OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of directed locates returned with a 'not found'."
      ::=  { ibmappnDirPerf 9 }
ibmappnDirNotFoundBcastLocates OBJECT-TYPE
      SYNTAX Counter
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Number of broadcast locates returned with
           a not found."
      ::=  { ibmappnDirPerf 10 }
ibmappnDirLocateOutstands  OBJECT-TYPE
      SYNTAX Gauge
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Current number of outstanding locates,
          both directed and broadcast.  This value
          varies. A value of zero indicates
          that no locates are unanswered."
      ::=  { ibmappnDirPerf 11 }
  1. -APPN Directory table
  1. - This table contains information about all known
  2. - LUs and TPs.
ibmappnDirTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnDirEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION

McKenzie & Cheng [Page 102] RFC 1593 SNA APPN Node MIB March 1994

           "Table containing information about
           all known LUs and TPs."
      ::= { ibmappnDir 2 }
ibmappnDirEntry OBJECT-TYPE
      SYNTAX IbmappnDirEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table is indexed by the LU name."
      INDEX
             {ibmappnDirLuName}
      ::= { ibmappnDirTable 1 }
IbmappnDirEntry ::= SEQUENCE {
      ibmappnDirLuName                   DisplayString,
      ibmappnDirServerName               DisplayString,
      ibmappnDirLuOwnerName              DisplayString,
      ibmappnDirLuLocation               INTEGER,
      ibmappnDirType                     INTEGER,
      ibmappnDirWildCard                 INTEGER
                             }
ibmappnDirLuName          OBJECT-TYPE
      SYNTAX DisplayString  (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Fully-qualified network LU name in the
           domain of the serving network node."
      ::=  { ibmappnDirEntry 1 }
ibmappnDirServerName        OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Fully-qualified control point (CP) name of the
            network node server.  For unassociated end node
            entries, the end node fully-qualified name
            is returned."
      ::=  { ibmappnDirEntry 2 }

McKenzie & Cheng [Page 103] RFC 1593 SNA APPN Node MIB March 1994

ibmappnDirLuOwnerName    OBJECT-TYPE
      SYNTAX DisplayString (SIZE (3..17))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Fully-qualified CP name of the node at which
           the LU is located.  This name is the same as the
           serving NN name when the LU is located at a
           network node or an unassociated end node.  It is
           also the same as the fully-qualified LU name
           when this is the control point LU for this node."
      ::=  { ibmappnDirEntry 3 }
ibmappnDirLuLocation        OBJECT-TYPE
      SYNTAX INTEGER {
                     local(1),     --Local
                     domain(2),    --Domain
                     xdomain(3)    --Cross Domain
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Specifies the location of the LU."
      ::=  { ibmappnDirEntry 4 }
ibmappnDirType             OBJECT-TYPE
      SYNTAX INTEGER {
                     home(1),      --defined as home entry
                     cache(2),     --learned over time
                     registered(3) --registered by end node
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Directory types are:
            1 - Home
                  The LU is in the domain of the local network node
                  and the LU information has been configured at the
                  local node.
            2 - Cache
                  The LU has previously been located by a broadcast
                  search and the location information has been saved.
            3 - Register

McKenzie & Cheng [Page 104] RFC 1593 SNA APPN Node MIB March 1994

                  The LU is at an end node that is in the domain
                  of the local network node.  Registered entries
                  are registered by the served end node."
      ::=  { ibmappnDirEntry 5 }
ibmappnDirWildCard         OBJECT-TYPE
      SYNTAX INTEGER {
                      other(1),
                      explicit-entry(2),
                      partial-wildcard(3),
                      full-wildcard(4)
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "1 - Other means unknown type of LU entry.
           2 - Expliced-entry means the full LUNAME will be used
               for locating this LU.
           3 - Partial-wildcard means only the non-blank portions
               of the LUNAME will be used for locating this LU.
           4 - Full-wildcard means all LUNAMES will be directed
               to this LU."
      ::=  { ibmappnDirEntry 6 }
  1. - The APPN Class of Service group *
ibmappnCos  OBJECT IDENTIFIER ::= { ibmappn 6  } --APPN COS
  1. - The APPN Class of Service (COS)
  1. - Class of Service is a means of expressing the quality of the routes
  2. - and the transmission priority of traffic which flows on these routes.
  3. - The quality of routes is specified by two tables, a COS weight table
  4. - for TGs and a COS weight table for nodes. These COS tables are
  5. - administratively assigned at each APPN node. Seven default tables
  1. - for TGs and a COS weight table for Nodes. These COS tables are
  2. - administratively assigned at each APPN node with seven default tables
  3. - being provided by IBM.
  4. -
  5. -
  6. - COS Name
  7. - Unqualified name identifying the class of service.
  8. - Transmission priority

McKenzie & Cheng [Page 105] RFC 1593 SNA APPN Node MIB March 1994

  1. - Transmission priority associated with this class of service
  2. - COS Node Row Table
  3. - At least one node row must be specified. The default
  4. - COS tables specify 8 rows.
  5. - Node Row Weight
  6. - Numeric value between 0 and 255 inclusive indicating
  7. - the weight associated with this row.
  8. - Route addition resist (min)
  9. - Numeric value between 0 and 255 inclusive indicating
  10. - the minimum route addition resistance for this row.
  11. - Route addition resist (max)
  12. - Numeric value between 0 and 255 inclusive indicating
  13. - the maximum route addition resistance for this row.
  14. - Congestion (min)
  15. - Indicates whether this class of service for this row
  16. - will accept congestion. Yes or No must be specified.
  17. - Congestion (max)
  18. - Indicates whether this Class of Service for this row
  19. - will accept congestion. Yes or No must be specified.
  20. -
  21. - COS TG Row table
  22. - At least one TG row must be specified with the defaults
  23. - COS tables specify 8 rows.
  24. - TG Row Weight
  25. - Numeric value between 0 and 255 inclusive indicating
  26. - the weight associated with this row.
  27. - Effective capacity (min)
  28. - Indicates the lowest acceptable value for this row.
  29. - Effective capacity (max)
  30. - Indicates the highest required value for this row.
  31. - Cost per connect time (min)
  32. - Indicates the lowest connect cost per unit time value
  33. - for this row. This value is between 0 and 255 inclusive.
  34. - Cost per connect time (max)
  35. - Indicates the highest connect cost per unit time value
  36. - for this row. This value is between 0 and 255 inclusive.
  37. - Cost per byte (min)
  38. - Indicates the lowest cost per byte value
  39. - for this row. This value is between 0 and 255 inclusive.
  40. - Cost per byte (max)
  41. - Indicates the highest cost per byte value
  42. - for this row. This value is between 0 and 255 inclusive.
  43. - Security (min)
  44. - Indicates the lowest acceptable value for security
  45. - for this row. This value is one of seven values.
  46. - Security (max)
  47. - Indicates the highest acceptable value for security
  48. - for this row. This value is one of seven values.

McKenzie & Cheng [Page 106] RFC 1593 SNA APPN Node MIB March 1994

  1. - Propagation delay (min)
  2. - Indicates the lowest acceptable propagation delay value
  3. - for this row.
  4. - Propagation delay (max)
  5. - Indicates the highest acceptable propagation delay value
  6. - for this row.
  7. - User defined 1 (min)
  8. - Indicates the lowest acceptable value
  9. - for this row. This value is between 0 and 255 inclusive.
  10. - User defined 1 (max)
  11. - Indicates the highest acceptable value
  12. - for this row. This value is between 0 and 255 inclusive.
  13. - User defined 2 (min)
  14. - Same as user defined 1
  15. - User defined 2 (max)
  16. - Same as user defined 1
  17. - User defined 3 (min)
  18. - Same as user defined 1
  19. - User defined 3 (max)
  20. - Same as user defined 1
  21. -
  22. -
  23. -
  24. -Due to SNMP ASN.1 limitations the COS table is defined
  25. -in the following format.
  26. -
  27. - MODE name table
  28. - MODE Name (index)
  29. - COS Name
  30. -
  31. - COS name table
  32. - COS Name (index)
  33. - Transmission priority
  34. -
  35. - COS node row table
  36. - COS Name (index1)
  37. - Index2
  38. - Node Row Weight
  39. - Rte addition resist (min)
  40. - Rte addition resist (max)
  41. - Congestion (min)
  42. - Congestion (max)
  43. -
  44. - COS TG row table
  45. - COS Name (index1)
  46. - Index
  47. - TG Row Weight
  48. - Effective capacity (min)

McKenzie & Cheng [Page 107] RFC 1593 SNA APPN Node MIB March 1994

  1. - Effective capacity (max)
  2. - Cost per conn time (min)
  3. - Cost per conn time (max)
  4. - cost per byte (min)
  5. - cost per byte (max)
  6. - Security (min)
  7. - Security (max)
  8. - Propagation delay (min)
  9. - Propagation delay (max)
  10. - User defined 1 (min)
  11. - User defined 1 (max)
  12. - User defined 2 (min)
  13. - User defined 2 (max)
  14. - User defined 3 (min)
  15. - User defined 3 (max)
  16. -
  17. - ibmappnCosModeTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmappnCosModeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table representing all of the defined mode names for this node. The table contains the matching COS name." ::= { ibmappnCos 1 } ibmappnCosModeEntry OBJECT-TYPE SYNTAX IbmappnCosModeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is indexed by the Mode Name." INDEX {ibmappnCosModeName} ::= { ibmappnCosModeTable 1 } IbmappnCosModeEntry ::= SEQUENCE { ibmappnCosModeName DisplayString, ibmappnCosModeCosName DisplayString } ibmappnCosModeName OBJECT-TYPE McKenzie & Cheng [Page 108] RFC 1593 SNA APPN Node MIB March 1994 SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Administratively-assigned name for this mode entry." ::= { ibmappnCosModeEntry 1 } ibmappnCosModeCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "An administratively assigned name for this Class of Service." ::= { ibmappnCosModeEntry 2 } –
ibmappnCosNameTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnCosNameEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
          "Table representing all of the defined class-of-service
           names for this node.  The COS node and TG tables are
           accessed using the same index, which is the COS name."
      ::= { ibmappnCos 2 }
ibmappnCosNameEntry OBJECT-TYPE
      SYNTAX IbmappnCosNameEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The COS name is the index to this table."
      INDEX
             {ibmappnCosName}
      ::= { ibmappnCosNameTable 1 }
IbmappnCosNameEntry ::= SEQUENCE {
      ibmappnCosName                     DisplayString,
      ibmappnCosTransPriority            INTEGER

McKenzie & Cheng [Page 109] RFC 1593 SNA APPN Node MIB March 1994

                                 }
ibmappnCosName              OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Administratively-assigned name for this
           class of service."
      ::=  { ibmappnCosNameEntry 1 }
ibmappnCosTransPriority OBJECT-TYPE
      SYNTAX INTEGER {
                     low(1),               --X'01'
                     medium(2),            --X'02'
                     high(3),              --X'03'
                     network(4)            --X'04'
                     }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Transmission priority for this
            class of service.  Values are:
              Low
              Medium
              High
              Network                                      "
      ::=  { ibmappnCosNameEntry 2 }
ibmappnCosNodeRowTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnCosNodeRowEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "This table contains all node-row information for all
            class of service in this node."
      ::= { ibmappnCos 3 }
ibmappnCosNodeRowEntry OBJECT-TYPE
      SYNTAX IbmappnCosNodeRowEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION

McKenzie & Cheng [Page 110] RFC 1593 SNA APPN Node MIB March 1994

           "The COS name is the first index and a integer
            is the second index to insure a unique index."
      INDEX
             {ibmappnCosNodeRowName,
              ibmappnCosNodeRowIndex}
      ::= { ibmappnCosNodeRowTable 1 }
IbmappnCosNodeRowEntry ::= SEQUENCE {
      ibmappnCosNodeRowName                 DisplayString,
      ibmappnCosNodeRowIndex                INTEGER,
--Node Row Group
      ibmappnCosNodeRowWgt                  DisplayString,
      ibmappnCosNodeRowResistMin            INTEGER,
      ibmappnCosNodeRowResistMax            INTEGER,
      ibmappnCosNodeRowMinCongestAllow      INTEGER,
      ibmappnCosNodeRowMaxCongestAllow      INTEGER
                                 }
ibmappnCosNodeRowName              OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Administratively-assigned name for this
           class of service."
      ::=  { ibmappnCosNodeRowEntry 1 }
ibmappnCosNodeRowIndex     OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Index of COS name.  This same value is used
            to access the node and TG COS tables.
            Range of values is 0-255."
      ::=  { ibmappnCosNodeRowEntry 2 }
  1. -Node Row Group
ibmappnCosNodeRowWgt     OBJECT-TYPE
      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION

McKenzie & Cheng [Page 111] RFC 1593 SNA APPN Node MIB March 1994

           "Weight to be associated with the nodes
            that fit the criteria specified by this node row."
      ::=  { ibmappnCosNodeRowEntry 3 }
ibmappnCosNodeRowResistMin       OBJECT-TYPE
      SYNTAX INTEGER   (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Minimum route addition resistance value
           for this node. Range of values is 0-255.
           The lower the value, the more desirable
           the node is for intermediate routing."
      ::=  { ibmappnCosNodeRowEntry 4 }
ibmappnCosNodeRowResistMax  OBJECT-TYPE
      SYNTAX INTEGER   (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Maximum route addition resistance value
           for this node. Range of values is 0-255.
           The lower the value, the more desirable
           the node is for intermediate routing."
      ::=  { ibmappnCosNodeRowEntry 5 }
ibmappnCosNodeRowMinCongestAllow OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether low congestion will be
            tolerated.  The minimum and maximum parameters
            will allow specifying either low-congested,
            high-congested, or either to be used."
      ::=  { ibmappnCosNodeRowEntry 6 }
ibmappnCosNodeRowMaxCongestAllow OBJECT-TYPE
      SYNTAX INTEGER {yes(1), no(2)}
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Indicates whether high congestion will be
            tolerated.  The minimum and maximum parameters

McKenzie & Cheng [Page 112] RFC 1593 SNA APPN Node MIB March 1994

            will allow specifying either low-congested,
            high-congested, or either to be used."
      ::=  { ibmappnCosNodeRowEntry 7 }
  1. - COS TG row table
  2. - Index
  3. - TG Row Weight
  4. - Effective capacity (min)
  5. - Effective capacity (max)
  6. - Cost per conn time (min)
  7. - Cost per conn time (max)
  8. - cost per byte (min)
  9. - cost per byte (max)
  10. - Security (min)
  11. - Security (max)
  12. - Propagation delay (min)
  13. - Propagation delay (max)
  14. - User defined 1 (min)
  15. - User defined 1 (max)
  16. - User defined 2 (min)
  17. - User defined 2 (max)
  18. - User defined 3 (min)
  19. - User defined 3 (max)
  20. -
ibmappnCosTgRowTable OBJECT-TYPE
      SYNTAX SEQUENCE OF IbmappnCosTgRowEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "Table containing all the Tg-row information for all
            class of service defined in this node."
      ::= { ibmappnCos 4 }
ibmappnCosTgRowEntry OBJECT-TYPE
      SYNTAX IbmappnCosTgRowEntry
      ACCESS not-accessible
      STATUS mandatory
      DESCRIPTION
           "The TgRowName and the TgRowIndex are the index
           for this table."
      INDEX
             {ibmappnCosTgRowName,
              ibmappnCosTgRowIndex}

McKenzie & Cheng [Page 113] RFC 1593 SNA APPN Node MIB March 1994

      ::= { ibmappnCosTgRowTable 1 }
IbmappnCosTgRowEntry ::= SEQUENCE {
      ibmappnCosTgRowName                 DisplayString,
      ibmappnCosTgRowIndex                INTEGER,
--TG Row Group
      ibmappnCosTgRowWgt                   DisplayString,
      ibmappnCosTgRowEffCapMin             INTEGER,
      ibmappnCosTgRowEffCapMax             INTEGER,
      ibmappnCosTgRowConnCostMin           INTEGER,
      ibmappnCosTgRowConnCostMax           INTEGER,
      ibmappnCosTgRowByteCostMin           INTEGER,
      ibmappnCosTgRowByteCostMax           INTEGER,
      ibmappnCosTgRowSecurityMin           INTEGER,
      ibmappnCosTgRowSecurityMax           INTEGER,
      ibmappnCosTgRowDelayMin              INTEGER,
      ibmappnCosTgRowDelayMax              INTEGER,
      ibmappnCosTgRowUsr1Min               INTEGER,
      ibmappnCosTgRowUsr1Max               INTEGER,
      ibmappnCosTgRowUsr2Min               INTEGER,
      ibmappnCosTgRowUsr2Max               INTEGER,
      ibmappnCosTgRowUsr3Min               INTEGER,
      ibmappnCosTgRowUsr3Max               INTEGER
                              }
ibmappnCosTgRowName              OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..8))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Administratively-assigned name for this
           class of service."
      ::=  { ibmappnCosTgRowEntry 1 }
ibmappnCosTgRowIndex     OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Index of COS name.  This same value is used
            to access the node and TG COS tables."
      ::=  { ibmappnCosTgRowEntry 2 }
  1. -TG Row
ibmappnCosTgRowWgt       OBJECT-TYPE

McKenzie & Cheng [Page 114] RFC 1593 SNA APPN Node MIB March 1994

      SYNTAX DisplayString
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Weight to be associated with the nodes
            that fit the criteria specified by this tg-row."
      ::=  { ibmappnCosTgRowEntry 3 }
ibmappnCosTgRowEffCapMin   OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Minimum acceptable speed for this Class of Service.
           The effective capacity is an integer value that indicates
           the actual kilo bits per second.
           It is derived from the link bandwidth and maximum load
           factor with the range of 0 thru 603,979,776."
      ::=  { ibmappnCosTgRowEntry 4 }
ibmappnCosTgRowEffCapMax   OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Maximum acceptable speed for this Class of Service.
           The effective capacity is an integer value that indicates
           the actual kilo bits per second.
           It is derived from the link bandwidth and maximum load
           factor with the range of 0 thru 603,979,776."
      ::=  { ibmappnCosTgRowEntry 5 }
ibmappnCosTgRowConnCostMin OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Minimum acceptable cost per connect time
           for this Class of Service.
           Cost per connect time: a value representing
           the relative cost per unit of time to use
           the TG. Range is from 0, which means no cost,
           to 255."
      ::=  { ibmappnCosTgRowEntry 6 }

McKenzie & Cheng [Page 115] RFC 1593 SNA APPN Node MIB March 1994

ibmappnCosTgRowConnCostMax OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "Maximum acceptable cost per connect time
           for this Class of Service.
           Cost per connect time: a value representing
           the relative cost per unit of time to use
           the TG. Range is from 0, which means no cost,
           to 255."
      ::=  { ibmappnCosTgRowEntry 7 }
ibmappnCosTgRowByteCostMin  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Minimum acceptable cost per byte
            for this Class of Service."
      ::=  { ibmappnCosTgRowEntry 8 }
ibmappnCosTgRowByteCostMax  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Maximum acceptable cost per byte
            for this Class of Service."
      ::=  { ibmappnCosTgRowEntry 9 }
ibmappnCosTgRowSecurityMin  OBJECT-TYPE
      SYNTAX INTEGER {
                     nonsecure(1),                --X'01'
                     publicSwitchedNetwork(32),   --X'20'
                     undergroundCable(64),        --X'40'
                     secureConduit(96),           --X'60'
                     guardedConduit(128),         --X'80'
                     encrypted(160),              --X'A0'
                     guardedRadiation(192)        --X'C0'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Minimum acceptable security

McKenzie & Cheng [Page 116] RFC 1593 SNA APPN Node MIB March 1994

            for this Class of Service."
      ::=  { ibmappnCosTgRowEntry 10 }
ibmappnCosTgRowSecurityMax  OBJECT-TYPE
      SYNTAX INTEGER {
                     nonsecure(1),                --X'01'
                     publicSwitchedNetwork(32),   --X'20'
                     undergroundCable(64),        --X'40'
                     secureConduit(96),           --X'60'
                     guardedConduit(128),         --X'80'
                     encrypted(160),              --X'A0'
                     guardedRadiation(192)        --X'C0'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Maximum acceptable security
            for this Class of Service."
      ::=  { ibmappnCosTgRowEntry 11 }
ibmappnCosTgRowDelayMin  OBJECT-TYPE
      SYNTAX INTEGER {
                     minimum(0),                 --X'00'
                     negligible(384),            --X'4C'
                     terrestrial(9216),          --X'71'
                     packet(147456),             --X'91'
                     long(294912),               --X'99'
                     maximum(2013265920)         --X'FF'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
        "Minimum acceptable propagation delay for this class of service.
         Relative amount of time that it takes for a signal to travel
         the length of the logical link.  This time is represented in
         micro seconds, with the more values enumerated."
      ::=  { ibmappnCosTgRowEntry 12 }
ibmappnCosTgRowDelayMax  OBJECT-TYPE
      SYNTAX INTEGER {
                     minimum(0),                 --X'00'
                     negligible(384),            --X'4C'
                     terrestrial(9216),          --X'71'
                     packet(147456),             --X'91'
                     long(294912),               --X'99'

McKenzie & Cheng [Page 117] RFC 1593 SNA APPN Node MIB March 1994

                     maximum(2013265920)         --X'FF'
             }
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
        "Maximum acceptable propagation delay for this class of service.
         Relative amount of time that it takes for a signal to travel
         the length of the logical link.  This time is represented in
         micro seconds, with the more values enumerated."
      ::=  { ibmappnCosTgRowEntry 13 }
ibmappnCosTgRowUsr1Min  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Minimum acceptable value for this
            user defined characteristic.
            Range of values is 0-255."
      ::=  { ibmappnCosTgRowEntry 14 }
ibmappnCosTgRowUsr1Max  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Maximum acceptable value for this
            user defined characteristic.
            Range of values is 0-255."
      ::=  { ibmappnCosTgRowEntry 15 }
ibmappnCosTgRowUsr2Min  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Minimum acceptable value for this
            user defined characteristic.
            Range of values is 0-255."
      ::=  { ibmappnCosTgRowEntry 16 }
ibmappnCosTgRowUsr2Max  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only

McKenzie & Cheng [Page 118] RFC 1593 SNA APPN Node MIB March 1994

      STATUS mandatory
      DESCRIPTION
           "A Maximum acceptable value for this
            user defined characteristic."
      ::=  { ibmappnCosTgRowEntry 17 }
ibmappnCosTgRowUsr3Min  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Minimum acceptable value for this
            user defined characteristic.
            Range of values is 0-255."
      ::=  { ibmappnCosTgRowEntry 18 }
ibmappnCosTgRowUsr3Max  OBJECT-TYPE
      SYNTAX INTEGER (0..255)
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
           "Maximum acceptable value for this
            user defined characteristic.
            Range of values is 0-255."
      ::=  { ibmappnCosTgRowEntry 19 }
END

3.0 Acknowledgements

 Thanks go to David Chen, Leo Temoshenko, and Mike Allen for their
 contribution and support through the development process.

4.0 Security Considerations

 Security issues are not discussed in this memo.

McKenzie & Cheng [Page 119] RFC 1593 SNA APPN Node MIB March 1994

5.0 Authors' Addresses

 William F. McKenzie
 IBM Networking Systems
 P. O. Box 12195
 Research Triangle Park, NC  27709
 US
 Phone: +1 919 254 5705
 EMail: mckenzie@ralvma.vnet.ibm.com
 Jia-bing R. Cheng
 IBM Networking Systems
 P. O. Box 12195
 Research Triangle Park, NC  27709
 US
 Phone: +1 919 254 4434
 EMail: cheng@ralvm6.vnet.ibm.com

McKenzie & Cheng [Page 120]

/data/webs/external/dokuwiki/data/pages/rfc/rfc1593.txt · Last modified: 1994/03/04 01:21 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki