GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


rfc:rfc1219

Network Working Group P. Tsuchiya Request for Comments: 1219 Bellcore

                                                            April 1991
                On the Assignment of Subnet Numbers

Status Of This Memo

 This memo suggests a new procedure for assigning subnet numbers.  Use
 of this assignment technique within a network would be a purely local
 matter, and would not effect other networks.  Therefore, the use of
 these procedures is entirely discretionary.
 This memo provides information for the Internet community.  It does
 not specify an Internet standard.  Distribution of this memo is
 unlimited.

Overview

 RFC-950 [2] specifies a procedure for subnetting Internet addresses
 using a bit-mask.  While RFC-950 allows the "ones" in the subnet mask
 to be non-contiguous, RFC-950 recommends that 1) they be contiguous,
 and 2) that they occupy the most significant bits of the "host" part
 of the internet address.
 RFC-950 did not specify whether different subnets of the same network
 may have different masks.  This ambiguity was unfortunate, as it
 resulted in development of routing protocols that do not support
 different masks; see e.g., RIP [6].  The Gateway Requirements RFC [7]
 settled the issue in favor of allowing different masks, and therefore
 future routing protocols may be expected to support this feature;
 OSPF [3] is an example.
 The network administrator must of course determine the mask for each
 subnet.  This involves making an estimate of how many hosts each
 subnet is expected to have.  As it is often impossible to predict how
 large each subnet will grow, inefficient choices are often made, with
 some subnets under-utilized, and others possibly requiring
 renumbering because of exceeded capacity.
 This memo specifies a procedure for assigning subnet numbers that
 eliminates the need to estimate subnet size.  Essentially, host bits
 (mask = 0) are assigned from the least significant bit working
 towards the most, and subnet bits (mask = 1) are assigned from the
 most significant bit working towards the least.  As subnets grow,
 more host bits are assigned.  As the number of subnets grows, more
 subnet bits are assigned.  While this process does sometimes result

Tsuchiya [Page 1] RFC 1219 On the Assignment of Subnet Numbers April 1991

 in new subnet masks, no host ever need change addresses.
 This technique is not new, but it is also not widely known, and even
 less widely implemented.  With the development of new routing
 protocols such as OSPF, it is possible to take full advantage of this
 technique.  The purpose of this memo, then, is to make this technique
 widely known, and to specify it exactly.
 This memo requires no changes to existing Internet standards.  It
 does, however, require that the intra-domain routing protocol handle
 multiple different subnet masks.

Acknowledgments

 The author would like to thank Phil Karn, Charles Lynn, Jeff Mogul,
 and Charles Wolverton for their helpful suggestions.  Special thanks
 go to Joel Halpern for his painstaking debugging of the detailed
 specification and the examples.

1. Motivation

 The Subnetting standard, RFC-950, specifies that the Host part of the
 formally 2-level Internet address can be divided into two fields,
 Subnet and Host.  This gives the Internet address a third level of
 hierarchy, and the concomitant firewalls and savings in routing
 overhead.  It also introduces increased inefficiency in the
 allocation of addresses.
 This inefficiency arises from the fact that the network administrator
 typically over-estimates the size (number of hosts) of any single
 subnetwork, in order to prevent future re-addressing of subnets.  It
 may also occur if the routing protocol being used does not handle
 different length subnets, and the administrator must therefore give
 every subnet an amount of space equivalent to that received by the
 largest subnet. (This RFC does not help in the latter case, as the
 technique herein requires different length subnets.)
 The administrative hassle associated with changing the subnet
 structure of a network can be considerable.  For instance, consider
 the following case.  A network has three subnets A, B, and C.  Assume
 that the lowest significant byte is the host part, and the next byte
 is the subnet part (that is, the mask is 255.255.255.0).  Assume
 further that A has subnet 1.0, B has subnet 2.0, and C has subnet
 3.0.
 Now, assume that B grows beyond its allocation of 254 hosts.
 Ideally, we would like to simply change B's mask without changing any
 of the host addresses in B.  However, the subnets numerically above

Tsuchiya [Page 2] RFC 1219 On the Assignment of Subnet Numbers April 1991

 and below B are already taken by A and C.  (If say 3.0 was not taken
 by C, B's mask could be changed from 255.0 (ff00) to 254.0 (fe00).
 In this case, all of B's existing addresses would still match the new
 subnet.  Indeed, if non-contiguous masks were in use, it might be
 possible for B to find some other mask bit to change to 0.  However,
 non-contiguous masks are generally not in favor, as they impose
 limitations on certain forwarding table lookup algorithms.  Indeed,
 RFC-950 discourages their use.)
 So, the choices available to the network administrator are to 1) form
 two subnets out of the existing one, or 2) renumber the subnet so
 that the subnet ends up with a smaller (fewer 1's) mask.  Choice 1
 can either be accomplished physically or logically.  Physically
 forming two subnets requires partitioning the subnet and inserting a
 gateway between the two partitions.  For obvious reasons, this is not
 a desirable course of action.  Logically forming two subnets can be
 done by simply assigning another subnet number (say 4.0) to the same
 subnet, and assigning host addresses under the new subnet.  The
 result of this logical partition is that the hosts with different
 subnet numbers will not recognize that the others are on the same
 subnet, and will send packets to the default gateway rather than
 directly to the host.  In fact, this is not such a bad solution,
 because assuming that the gateway is capable of recognizing multiple
 subnet numbers on the same subnet, the gateway will simply send the
 host an ICMP Redirect [4], and subsequent packets will go directly to
 the host [1] (this may not work correctly on all hosts).
 If, however, neither choice is acceptable or possible, then the
 network administrator must assign a new subnet number to B, thus
 renumbering the existing hosts, modifying the Domain Name System
 entries, and changing any other configuration files that have
 hardwired addresses for hosts in subnet B.

2. A More Flexible and Efficient Technique for Assigning Subnet Numbers

 In order to help explain the new technique, we shall show what is
 wrong with what is currently done now.  Currently, most subnets are
 assigned by splitting the host part of the address in two fields; the
 subnet field and the host field.  Mask bits are one for subnet field
 bits, and 0 for host field bits.  (In all of our addresses, the least
 significant bit (LSB) is on the right, the most significant bit (MSB)
 is on the left.)
      MSB                                LSB
      --------------------------------------
     | subnet field    | host field         |
      --------------------------------------

Tsuchiya [Page 3] RFC 1219 On the Assignment of Subnet Numbers April 1991

 The subnet field could be different lengths for different size
 subnets.  For instance, say a network had two large subnets and the
 rest small subnets (by large subnet we mean a large number of hosts).
 Then the network administrator might assign two types of addresses:
  1. ————————————-

| subnet | host | large subnets

  1. ————————————-
  1. ————————————-

| subnet | host | small subnets

  1. ————————————-
 In this case, the full range of subnet numbers would not be available
 to the small subnets, as the bits in the small subnet that correspond
 to those in the large subnet could not have the same values as those
 in the large subnets.  For instance, say that the large subnets had
 4-bit subnet numbers, and the small subnets had 8-bit subnet numbers.
 If the large subnets had values 0001 and 0010, then subnet numbers in
 the range 00010000 to 00101111 could not be assigned to the small
 subnets, otherwise there will be addresses that would match both
 subnets.
 In any event, a network administrator will typically assign values to
 the two fields in numerical order.  For example, within a given
 subnet, hosts will be numbered 1, 2, 3, etc.  Within a given network,
 subnets will be numbered 1, 2, 3, etc.  The result is that some
 number of bits on the right side of the subnet and host fields will
 be ones for some hosts and zeros for others, and some number of bits
 on the left side of the subnet and host fields will be zeros for all
 subnets and hosts.  The "all zeros" bits represent room for growth,
 and the "ones and zeros" bits represent bits already consumed by
 growth.
  1. ————————————-

| subnet field | host field |

     |-----+-----------+-------+------------|
     |     |           |       |            |
     | 0's | 1's & 0's |  0's  | 1's & 0's  |
        /\                /\
        ||                ||
      subnets can         hosts can grow here
      grow here
 Now, let's assume that the number of hosts in a certain subnet grows
 to the maximum allowed, but that there is still room in the subnet
 field to assign more addresses.  We then have the following:

Tsuchiya [Page 4] RFC 1219 On the Assignment of Subnet Numbers April 1991

  1. ————————————-

| subnet field | host field |

     |-----+-----------+--------------------|
     |     |           |                    |
     | 0's | 1's & 0's |     1's & 0's      |
 While the host field can no longer grow, there is still room in the
 address for growth.  The problem is that because of where the growth
 areas are situated, the remaining growth has been effectively
 reserved for subnets only.
 What should be done instead is to assign subnet numbers so that the
 ones start from the left of the subnet field and work right.  In this
 case we get the following:
  1. ————————————-

| subnet field | host field |

     |-----------+-------------+------------|
     |           |             |            |
     | 1's & 0's |    0's      | 1's & 0's  |
                       /\
                       ||
                  Both hosts and subnets can
                  grow here
 Now, both hosts and subnets individually have considerably more
 growing space than before, although the combined growing space is the
 same.  Since one can rarely predict how many hosts might end up in a
 subnet, or how many subnets there might eventually be, this
 arrangement allows for the maximum flexibility in growth.
 Actually, the previous figure is misleading.  The boundary between
 the host and subnet fields is being shown in the middle of the growth
 area.  However, the boundary could exist anywhere within the growth
 area.  Note that it is the mask itself that determines where the
 boundary is.  Ones in the mask indicate subnet bits, and zeros
 indicate host bits.  We will show later that in fact the boundary
 should lie somewhere in the middle.  Putting it there minimizes the
 number of times that the masks must be changed in hosts.
 2.1  Specification of the New Technique
 Having given the appropriate explanatory material, we can now specify
 the procedure for subnet number assignment.  We need the following
 definitions:
 Host-assigned Bits (h-bits):  These are the bits, contiguous from

Tsuchiya [Page 5] RFC 1219 On the Assignment of Subnet Numbers April 1991

    the right, for which host values, within a given subnet, contain
    both ones and zeros.  Different subnets may have different h-bits.
 Subnet-assigned Bits (s-bits):  These are the bits, contiguous from
    the left, which 1) are not h-bits, AND 2) are required to
    distinguish one subnet from another, AND 3) include all bits
    to the left of and including the right-most one.  Notice that
    different subnets may have different s-bits.
 Growth Bits (g-bits):  These are the "all zeros" bits in between
    the h-bits and s-bits.
 s-mask:  For a given subnet, the mask whereby all s-bits are one,
    and all g-bits and h-bits are zero.
 g-mask:  For a given subnet, the mask whereby all s-bits and g-bits
    are one, and all h-bits are zero.
 Subnet Field:  These are the one bits in the subnet mask (as
    defined in RFC-950).  These bits are on the left.  The subnet
    field must at least include all of the s-bits, and may
    additionally include some or all of the g-bits.
 Host Field:  These are the zero bits in the subnet mask.
    These bits are on the right.  The host field must at least
    include all of the h-bits, and may additionally include some
    or all of the g-bits.
 Mirror-image Counting:  Normal counting, in binary, causes one
    bits to start at the right and work left.  This is how host
    values are assigned.  However, for subnet assignment, we want
    the one bits to start at the left and work right.  This process
    is the mirror image of normal counting, where the MSB is swapped
    with the LSB, the second MSB is swapped with the second LSB, and
    so on.  So, where normal counting is:
              0       (reserved to mean "this host")
             01
             10
            011
            100
            101
            :
            :
      11...1110
      11...1111       (reserved to mean "all hosts")
    and so on, Mirror-image, or MI counting, is:

Tsuchiya [Page 6] RFC 1219 On the Assignment of Subnet Numbers April 1991

      0       (reserved to mean "this subnet")
      10
      01
      110
      001
      101
        :
        :
      011...11
      111...11        (reserved to mean "all subnets")
    and so on.  If the current MI counting value is, say, 001,
    the "next" MI value is 101, and the "previous" MI value is 11.
 Now we can specify the algorithm.  We have the following functions:
 Initialize(), AddSubnet(), RemoveSubnet(subnet#), AddHost(subnet#),
 and RemoveHost(subnet#,host#).
 Notice that the algorithm is described as though one state machine is
 executing it.  In reality, there may be a root Address Authority
 (RootAA) that assigns subnet numbers (Initialize, AddSubnet, and
 RemoveSubnet), and subnet AA, that assign host numbers within a
 subnet (AddHost and RemoveHost).  While in general the AAs can act
 independently, there are two cases where "coordination" is required
 between the rootAA and a subnetAA.  These are the cases where either
 the rootAA or the subnetAA "grabs" the last growth bit (in the former
 case because another subnet has been added, and in the latter because
 another host has been added).  Since it is impossible for the rootAA
 and a subnetAA to simultaneously grab the last growth bit, either one
 or the other must do it.
 Finally, note that the following C language style notation is used:
      &               bit-wise AND function
      ==              is equal to
      !=              is not equal to
      x-mask(X)       the x-mask of X (where x is s or g)
 Initialize():
    Assign the first subnet value to be 0 (the value reserved to mean
    "this subnet").  This is not assigned to any real subnet.
 AddSubnet():
    1.  Find the lowest non-zero (in MI counting) non-assigned subnet
        number S such that (S & g-mask(Y)) != (Y & g-mask(Y)) for all
        existing subnet numbers Y, (Y != S).
    2.  If all bits in S from the rightmost one bit left are ones,
        then label all bits to the left of and including one bit
        position to the right of the rightmost one bit in S to be

Tsuchiya [Page 7] RFC 1219 On the Assignment of Subnet Numbers April 1991

        s-bits. Else, label all bits to the left of and including the
        rightmost one bit in S to be s-bits.  This prevents the "all
        ones" value (which is the "all subnets" broadcast address)
        from being assigned to a subnet.  (Since no hosts have been
        added, the rightmost one bit is a subnet bit.)
    3.  Label all other bits in the address to be g-bits.  (By
        address, we mean that part of the IP address not including
        the network number.)
    4.  Set the subnet mask to include at least all s-bits, and
        optionally some g-bits.  The subnet mask must be contiguous.
        (Section 2.2 discusses the pros and cons of choosing a mask.)
    5.  For all existing subnet numbers Y (Y != S):
        51. If (S & s-mask(Y)) == (Y & s-mask(Y)), then:
            511.  Change the leftmost g-bit of Y to an s-bit.  If
                  the rootAA and YAA (the address authority for Y) are
                  separate AAs, then the YAA must be informed of the
                  change of bit status.  If this is the last g-bit,
                  then this change must be coordinated with YAA.
            512.  Expand the subnet mask for all hosts in Y if
                  necessary (that is, if the subnet mask no longer
                  includes all s-bits).
 RemoveSubnet(S):
    1.  Consider B to be the bit position of the rightmost s-bit in S.
    2.  Remove S.
    3.  For all existing subnet numbers Y:
        31.  If the bit in position B is not an s-bit, or if the bit
             in bit position B is a one, or if the bit in bit position
             B is a zero and all bits to the left of bit position B
             are ones, then do nothing (skip steps 32 and 33).
        32.  Change the s-bit in position B to a g-bit.
        33.  If for any other existing subnet numbers X
             (X & s-mask(Y)) == (Y & s-mask(Y)), then change the
             g-bit in position B back into an s-bit for Y.  Else,
             inform YAA that of the change of bit status.
 AddHost(S):
    1.  Create an address A consisting of subnet number S concatenated
        with zeros.
    2.  Assign to A the same h-bits, g-bits, and s-bits as the
        other host addresses.
    3.  Find the lowest non-zero (using normal counting) non-assigned
        host number H.
    4.  If all bits from the leftmost one bit to bit position 0 are
        ones, then execute steps 5 and 6 using bit position B equals
        one bit position to the left of the leftmost one bit in H.
        Else, execute steps 5 and 6 with bit position B equals
        the leftmost one bit in H.  This prevents the "all ones" value

Tsuchiya [Page 8] RFC 1219 On the Assignment of Subnet Numbers April 1991

        (which is the "all hosts" broadcast address) from being
        assigned to a host.
    5.  If bit position B is an s-bit, then the host cannot be added.
        Skip the remaining steps.
    6.  If bit position B is a g-bit:
        61.  Change the g-bit to an h-bit for all hosts in S.  Note
             that if this is the last g-bit, this change must be
             coordinated with the address authority assigning subnet
             numbers (see section 2.2).
        62.  Modify the subnet mask in all hosts if necessary.
    7.  Create a new address A consisting of S concatenated with H
    8.  Assign A to the host.
 RemoveHost(S,H):
    1.  Remove H.
    2.  If for all remaining host numbers in S, the value of the bit
        position of the leftmost h-bit is zero, and there is a zero in
        at least one of the bit positions to the right of the leftmost
        h-bit, then for all hosts change the leftmost h-bit into a
        g-bit.
    It is worth noting here that this technique is a 2-level subset of
    the more general n-level kampai addressing [5].  The main
    difference here is that n-level kampai results in non-contiguous
    masks, while 2-level does not.  In the description of kampai
    addressing in [5], g-bits are called a-bits, h-bits are called
    g-bits, and s-bits are called i-bits.
 2.2  An Example
 For this example, we assume a class C network, so we will only need
 to work with 8 bits.  We start with 3 subnets, A, B, and C.  Our
 nomenclature is h for h-bit and g for g-bit.  Note that h-bits can be
 one or zero, but g-bits are all zero.  The remaining bits are s-bits,
 but are shown as 1's and 0's according to the subnet number
 assignment.  The space is just to make the addresses and masks easier
 to read.  Finally, we number our bits 0 to 7 from right to left as
 shown below.
      Subnet  Address         Mask
      A       10gg ghhh       1111 0000
      B       01gg ghhh       1111 0000
      C       110g ghhh       1111 0000
          bit 7       bit 0
 We see that each subnet has at most 6 hosts (because of the three h-
 bits).  Notice that we have chosen the masks so that there is room
 for growth in both hosts and subnets without requiring a mask change.

Tsuchiya [Page 9] RFC 1219 On the Assignment of Subnet Numbers April 1991

 However, we have generally allowed for more growth in subnets than in
 hosts because adding new subnets can cause mask changes in existing
 subnets, while adding new hosts in a subnet only causes that subnet's
 mask to change.
 Further, if a subnet's mask must change, but not all hosts are
 reconfigured at the same time, then it is less damaging if the not
 yet reconfigured hosts have too large a mask (too many ones) than if
 they have too small a mask.  This is because with too large a mask, a
 host may think that another host which is in fact on the subnet is on
 another subnet.  In this case, the host will send packets to the
 gateway, and will be redirected to the host.
 However, with too small a mask, a host may think that another host
 which is in fact not on the subnet is on the subnet, and will ARP for
 that host but receive no reply.  (Note that broadcasts may fail if
 all masks do not match.)
 Finally, notice that subnet C requires three s-bits instead of just
 two.  This is because with just two, the subnet address of C could be
 "11" (rather than "110"), which is a broadcast value.  Step 2 of
 AddSubnet checks for this case.
 Now, a fourth subnet, D, also with 6 hosts, is added.  We get:
      Subnet  Addr            Mask
      A       10gg ghhh       1111 0000
      B       01gg ghhh       1111 0000
      C       110g ghhh       1111 0000
      D       001g ghhh       1111 0000
 Notice that none of the original subnets required a change in any of
 their status bits.  This is because, when D compared its subnet
 number with the others (step 5 of AddSubnet(), using the s-mask),
 they were all different.  In other words, a router would be able to
 distinguish an address in D from addresses in A, B, and C.
 Next, a fifth subnet, E, is added.  We get:
      Subnet  Addr            Mask
      A       100g ghhh       1111 0000
      B       01gg ghhh       1111 0000
      C       110g ghhh       1111 0000
      D       001g ghhh       1111 0000
      E       101g ghhh       1111 0000
 Notice that this time, A was forced to change its leftmost g-bit (bit
 5) into an s-bit, because bit 5 is needed to distinguish subnet A

Tsuchiya [Page 10] RFC 1219 On the Assignment of Subnet Numbers April 1991

 from subnet E (step 511 of AddSubnet()).  Changing bit 5 into an s-
 bit prevents hosts from being added to A to the point where bit 5
 would be changed into a one (that is, step 5 of AddHost() would
 fail).
 Notice also that if the masks in A, B, and C were originally set to
 1100.0000, then the addition of E would have caused A's mask to
 change to 1110.0000 (Step 512 of AddSubnet()).
 Next, 8 hosts each are added to subnets A and C, thus causing the
 right-most g-bit in each to change to an h-bit.
      Subnet  Addr            Mask
      A       100g hhhh       1111 0000
      B       01gg ghhh       1111 0000
      C       110g hhhh       1111 0000
      D       001g ghhh       1111 0000
      E       101g ghhh       1111 0000
 Notice again that no masks have changed.  If the masks for A, B, and
 C were originally set to 1111 1000, then they would have required
 changing (step 62 of AddHost()).
 Next, enough hosts are added to subnet B that all of its remaining
 g-bits become h-bits.
      Subnet  Addr            Mask
      A       100g hhhh       1111 0000
      B       01hh hhhh       1100 0000
      C       110g hhhh       1111 0000
      D       001g ghhh       1111 0000
      E       101g ghhh       1111 0000
 Notice here that the masks in B's subnet had to be changed to
 accommodate the new h-bits (step 62 of AddHost()).  Notice also that
 if the person assigning host addresses for B (B Address Authority, or
 BAA) is different than the person assigning network numbers (RootAA),
 then BAA must coordinate the change of its last g-bit to an h-bit
 with the RootAA.  This allows the RootAA to properly assign
 additional subnet numbers, as in the next step, where we add another
 subnet F:
      Subnet  Addr            Mask
      A       100g hhhh       1111 0000
      B       01hh hhhh       1100 0000
      C       110g hhhh       1111 0000
      D       001g ghhh       1111 0000
      E       101g ghhh       1111 0000

Tsuchiya [Page 11] RFC 1219 On the Assignment of Subnet Numbers April 1991

      F       1110 ghhh       1111 0000
 Notice that F received subnet number 1110 rather than subnet number
 011 (which is what comes after 101 in MI counting).  The reason is
 that 1) 011 is not distinguishable from B's subnet address using B's
 mask, and 2) we can't increase B's mask to make it distinguishable
 because B has already assigned hosts at bit position 5.  In other
 words, when the comparison of step 1 in AddSubnet() was tried on
 number 011, the two values were equal, and so the next number was
 tried.  In fact, no subnet numbers with 01 in bit positions 7 and 6
 can be assigned (unless B loses hosts).
 Next, subnet E is removed:
      Subnet  Addr            Mask
      A       10gg hhhh       1111 0000
      B       01hh hhhh       1100 0000
      C       110g hhhh       1111 0000
      D       001g ghhh       1111 0000
      F       1110 ghhh       1111 0000
 Notice that this caused subnet A to change an s-bit back into a g-
 bit.  This is because the equality of step 33 of RemoveSubnet() did
 not hold true for subnet A with respect to the remaining subnets.

References

 [1] Braden, R., "Requirements for Internet Hosts -- Communication
     Layers", RFC 1122, USC/Information Sciences Institute, October
     1989.
 [2] Mogul, J., and J. Postel, "Internet Standard Subnetting
     Procedure", RFC 950, USC/Information Sciences Institute, August
     1985.
 [3] Moy, J., "OSPF Specification", RFC 1131, Proteon, October 1989.
 [4] Postel, J., "Internet Control Message Protocol", RFC 792,
     USC/Information Sciences Institute, September 1981.
 [5] Tsuchiya, P., "Efficient and Flexible Hierarchical Address
     Assignment", TM-ARH-018495, Bellcore, February 1991.
 [6] Hedrick, C., "Routing Information Protocol" RFC 1058, Rutgers
     University, June 1988.
 [7] Braden, R., and J. Postel, "Requirements for Internet Gateways",
     RFC 1009, USC/Information Sciences Institute, June 1987.

Tsuchiya [Page 12] RFC 1219 On the Assignment of Subnet Numbers April 1991

Security Considerations

 Security issues are not discussed in this memo.

Author's Address

 Paul F. Tsuchiya
 Bellcore
 435 South St.5 South St.
 MRE 2L-281
 Morristown, NJ 07960
 Phone: 201 829-4484
 EMail: tsuchiya@thumper.bellcore.com

Tsuchiya [Page 13]

/data/webs/external/dokuwiki/data/pages/rfc/rfc1219.txt · Last modified: 1991/04/16 17:36 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki