stem can be set up so that a certain program runs between every frame of video (this is how some programs m... .
The second misunderstanding is the difference between hardware design, and address space. It makes no d... ct of less expensive hardware (allowing trade-off between resolution and bits/pixel) or brain-dead "standar... modes, you have to reinitialize (i.e. reboot) GEM between them, so I didn't 'X' that.
Hardware Assist: E
ard phone line, just like port 1.
The difference between this port and port 0 however, is that this port m... ant at
first (don't fool yourself).
Each letter between *'s represents a seperate processor (yes even thi
onger than 1000 characters, and will as a rule be
between 50 and 200 characters. More complicated and lengt... above batch statement will
assume a boolean "and" between arguments.
This scheme for doing simple knowledg
rite-Through.
Device Driver
An interface module between the device-independent portions of
the operating ... e IDE took over. An ESDI drive can
transfer data between the drive and controller at 10, 15, or 20
megabit... cy
modulation omits all clock pulses except those between pairs of zero
bits. See also FM, RLL.
Mickey
T... ms may
execute concurrently, with rapid switching between the programs giving
the appearance that all are e
.8K bits per second (bps). The transmission rate between the computer
and modem, depending on your equipm... uch faster than typical training times that range between
9 and 18 seconds for other modems.
Universal Co... is push-button switch is used primarily to switch between voice and data
communications during a call. De... riage Return)
key, shown in the example below between angle brackets. (Don't type the
angle bracke
oldering) a
jumper on the back of the motherboard between pins 1 and 2(7) of the
50MHz oscillator, and ran... re at positions 1, 7, 8, and 14, he
made jumpers between pins 5-7, 8-10, and 12-14. He disabled the
on-b... d surface mount crystal oscillator with a jumper between 3-5.
Then put the new crystal in the socket. T... 6, B2, and B6. Next solder
a little jumper wire between pins A2 and A6. Now get the 14 pin IC
socket, a
The result is a true
spread of stereo sound between stereo speakers or headphones.
... will find it travels
underneath the YM2149, between the rows of pins (underside of the board). This
et.
-You could also use a DPDT switch to switch between internal and
external keyboards. One side goes ... ard
has a problem with rollover. Try rolling over between two keys on the
same row, and you're just as like
es description. First of all there was no JP2
between the ROM and the CPU (oink), second there was no R... is connection on the bottom
side of the board between the CPU pins. Then i soldered in a new
connec... e to top side, thus
effectuating a connection between CPU A19 and Agnus A19. The rest is
fairly str
lowing table,
A represents the maximum distance between the card's left
edge and the contact area's left edge,
B represents the minimum distance between the card's left
edge and the contact area's right edge,
C represents the maximum distance between the card's top
edge and the contact area's upper edge,
D represents the minimum distance between the card's top
edge and the contact area's lowe
:
(1) What is OS/2?
(2) What are the differences between versions?
(3) What is Extended Services/2?
(4) Ho... -------------------
(2) What are the differences between versions?
IBM OS/2 Version 2.0 (CSD Level 02000,
I've often been asked the difference ³±
³ between the types of drive controllers and recording meth... tors. All devices in- ³±
³ between should have theirs removed. ³±
... . B >³16 15³ | ³±
³ ors have a "key" between pins DIRECTION SEL. >³18 17³ | ³±
... INDEX ³20 19³ | ³±
³ to transmit data between the READY ³22 21³ | ³±