*> TRAFFIC Interrupt or resume traffic after user interaction
with cha... e.
Here is an example of the System Output data, after being translated into
standard format by the UDC:
er government contractors and agencies.
In 1976, after his discharge from the Navy, Gary became a full- ... wrote the user manual.
DRI released CP/M-86 soon after IBM released DOS Version 1.0. DOS had fewer
featu
The Partition Resizer FAQ
Well, after many requests, PRESIZER.FAQ is finally here! I do... verwritten and deleted when the work is over. But after the data moving,
DOS doesn't know there are chang... re importat things to do first.
Q: Is there life after death?
A: I don't know that for sure, but I've go
thenticity verification (v1.1 before 4/1/93, v2.0 after). Please
redistribute only the original ar... information. If you receive an archive dated after 1/1/91 which fails
the authenticity check,
= 1 ICW4 needed
0021 w PIC ICW2,ICW3,ICW4 after ICW1 to 0020
ICW2:
bit 7-3 = address lines A... put buffer (ISA, EISA)
should only be read from after status port bit0 = 1
should only be written to ... command. 1=offline 0=online
bit1=0 activate NIC after reset command
bit2=1 start transmision of a pack... completed
bit 4 = 1 equipment check occurred after error
bit 3 = 1 not ready
bit 2 = 1 hea
Reserved
Note: Device word register valid only after FNINIT
FPU Flags Affected: None
CPU mode: Any
... f life
Note: Signature word register valid only after FNINIT
FPU Flags Affected: None
CPU mode: Any
... ; There are 3 banks (0, 1, 2) in Chip
; After initialization FPU select bank # 0.
FPU Flags A... ; There are 3 banks (0, 1, 2) in Chip
; After initialization FPU select bank # 0.
FPU Flags A
Stay Resident) A program which remains in memory
after terminating in order to provide services to other... of the DOS function call used to
remain in memory after termination.
Track
One of multiple concentric c... in harmful
code which is triggered by some event, after a certain number of
reproductions, or on a specif
you turn your computer off
immediately after quitting a program.
IT IS BEST TO WAIT AT LEAST FIVE SECONDS AFTER YOU QUIT AN
APPLICATION BEFORE YOU TURN
wide range of installed modems.
Link Diagnostics
After each call, you can display a Link Diagnostics scr... er
You can set the modem to automatically hang up after a specified number of
minutes if there is no act... ATE0 <Enter>
If no OK appears on your screen after you completed Step 4, review the
following ch... before Installing the Modem.
Just remember that after you load your communications software, you'll
ha
the oscillator around to get all the solder out. After you have
done all 4, if you have done a good job... as fine. Be warned that some cards may not work after this
modification. Most will work at 25MHz, but ... mes at 25MHz without a heatsink
(There is an "H" after the '040 and before the "RC"). This is the same... people. On some of these Mac's the CPU overheats after a while, so
Marlin suggests you add a fan to dis
the story of upgrading my A500 to 1MB Agnus.
After buying the Fat Lady (dfl 150,-) i opened up my A5... ransition
should be fairly easy. What i found after removing all screws and
and shielding defies ... nd connected to a 3D mounted transistor (shiver). After uttering
some strong words i also removed the... least the REV number.
The REV number said 3. After sitting down and taking a deep breath i
tried
machine on or reset.The reason for this is that after a cold or warm
boot the KERNEL roms go looking... s in the drives!). So
if the switch is changed after the roms have found what drives are
online, th