ting Double-Take
With Double-Take in memory, type CONTROL-F (do not
hit Return). Control-F puts you in the Function-Select
Mode, presenting you with the word "Fun... T
Unshift: NEW LIST
Typing "1" (after typing control-F) will activate the New-List
feature. Or typing... t the zero-key
has a Shift and Unshift option.
{Control-F is typed by pressing the CONTROL (or CTRL) key
not be adjusted.
Another Note: Tab is the same as Control-I.
Apple-T: TAB RULERS OFF/ON Pressing Apple-T t... rsor and "pulls back" characters to the right.
- Control-Y erases all characters to the right of
the curs... tuations.)
PRINTING THE FILE.MOVER SCREEN
Press Control-P at almost any time to dump the text screen to a... e hi-res screen in the VIEW option (page 24), and Control-P is ignored when FILE.MOVER expects you to type
ce" message after booting your
computer, press Control-Open-Apple-Option-N to see the names of the people
on the Apple //gs design team
B) Press Control-^ and then any key and the cursor will change int... monitor, enter a '#', and whenever you access the control
panel, you will have two new options, "Memory ... ng sequence of letters while holding
down the "CONTROL" key: AA AB TB ZB MA HR SS. This produces a hidd
built-in. On the IIGS it was selectable via the control panel, as was the screen display of the special c... llel devices also used one or more extra wires as control lines, including a "busy" line (so the receiving ... to the Parallel Printer Interface, but had fewer control codes. The "Centronics standard" used seven data... ing bits.<8> It would automatically send certain control codes to the printer when a program sent the prop
essage, the resource part of an extended file, a
control sequence for a NuFX utility program, or almost an...
$0000 = message_thread
$0001 = control_thread
$0002 = data_thread
$0003 = ... xxxx = all others undefined
$0001 = control_thread
thread_kind $0000 = cr... comp_thread_eof fields set to null (00).
If a control_thread indicates that a directory should be creat
d the built-in hardware and firmware could handle control of the mouse. MousePaint used the standard hi-re... grams that used the mouse as a pointing and input control device.
ComputerEyes was a video acquisition... voice) digital synthesizer, also with software to control it. Soundchaser System (Passport Designs, Inc.) ... me available in any quantity.
ROBOTS AND DEVICE CONTROL
Although used primarily for education purpo
thing very secret and thus tried to maintain some control over distribution of software. This may have bee... ed commands, often entered as combinations of the Control key and another letter, to carry out some of the ... d the previous standard of typed command input to control programs. Instead, they used a bit-mapped graphi... ck" on it to start the program! For more complex control, the Mac used a variation on the "magic menu" sys
r Seagate drive that you removed). These jumpers
control such things as capacity of the drive, volume part... The CMS card has 6 banks of 8 pairs of jumpers to control Device ID (DID),
Host ID (HID), Partition Startin... d the CPU.
-- Provides the address and control lines required by the Apple
II's mic... ce the 5380 IC with the Apple II CPU
control signals
3. RAM:
-- 8 ba
, for the sake of speed, were written to directly control the old Super Serial Card (rather than going thro... lication program and the hardware it is trying to control. On the IIGS, the firmware was designed after th... tain features of the IIGS to their own tastes, a "control panel" was designed (another idea borrowed from t... r, which was important on the IIGS because of the control panel feature and the way in which the Apple Desk
TONBYT
Microphone squelch SQUBYT
Mode control bits RECBYT
Receive baud rate ... COM
UART command transmitter COM
UART control parity mnable CON
UART control parity CON
UART control #stop bits CON
UART control #data bits CON
UART rxd to
ue disk operating system (DOS); their rudimentary control program would not be flexible enough for efficien... floppy disk and disk drive hardware itself. The control program the Woz wrote could be compared to a narr... nsulate the user from the complexity of trying to control the hardware. Consider the four parts of DOS as ... the hardware (the raw data on the disk and direct control of the disk drive), but you also increase greatly
il I found it in my manual.)
4. I assumed the CONTROL key, when pressed would switch control
between joystick and keyboard, but no such luck.
5. The DE... red arrow.
I have tried repeatedly using the CONTROL & SHIFT key along
with the arsow key, but ge... The dials
are missing and there is no volume control. Please send me
a working monitor.
12. I
--------------------------------------------
HAND CONTROL
-------------------------------------------------... t used for hand controllers
5,8 PDL0 & PDL1 Hand control inputs. Each of
these must be connected to a... (ignore) further command characters
(until Control-Reset or PR#1). Do not
format output or i... loop. Use <CTRL-RESET> to get
Z same
Control-T When issued from a remote device, this com