GENWiki

                  SAVING DF0: - BOOT UP FROM DF1: 

                                                by Les Ayling

  |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

  Several of my friends who are Amiga owners have had problems with the
 internal drive. This modification will overcome that problem by
 allowing Amiga 500 owners to boot from df1:.

  This mod is also useful for people who own the Commodore 5 1/4 inch
 drives and wish to boot from them. More importantly, people who have
 added an 80trk 5 1/4 inch drive (such as myself) as described in the
 file ADD_5.25_DRIVE can boot from it. As 5 1/4 inch disks can be
 bought for as low as $5.95 for 10 in some places, it is well worth
 considering as a cheap backup library option OR indeed as an
 alternative primary storage medium.

    You will need the following tools and parts:

• Low wattage soldering iron, suitable for PCB's
• DPDT switch mini toggle variety is fine
• 1 foot of ribbon cable
• solder
• small snippers
• hand drill
• tool to unscrew the @#$%^& non-standard case screws
• Exacto knife or similar

  Start by unscrewing the 6 hex style screws around the edge of the
 case (Goodbye warranty!).  Do not remove the three phillips screws as
 they are holding the drive in place.  Turn the machine back the right
 way up and remove the lid by pressing around the edge to ease off the
 catches.  Remove the keyboard making careful note of the orientation of
 the connector on the main board!!!!!  Now remove the further 4 hex
 screws which are holding the top rf shield in place and remove the
 shield.  Unplug the disk drive POWER cable from the drive end only.

  Remove the 34-way disk drive patch lead taking note of its orientation
 (This saves so much time when you have forgotten later on!)  Unscrew
 the Disk drive unit and remove it.

  The main PC board should now come free with the lower RF shield.
 Unscrew the hexagonal socket retainers on the I/O connectors at the
 rear of the board and this shield should come free.

  You are now ready to start!

  Locate connector 11 (CN11) on the component side, this is the socket
 that you just unplugged the disk drive patch lead from.  In front of it
 should be U8 which is an 8520 chip.

  CN11 is 2 rows of 34 pins.Count along the front row from the right
 hand side until you see the 5th and 6th pins (pins 9 and 11 of the
 connector respectively).  There should be two circuit traces that lead
 from these pins and disappear under U8.  Using the exacto knife cut
 both of these traces leaving no stray copper. A 1mm cut should be
 sufficient.

  Turn the board over to the solder side.
  Leave the board for a moment and get the DPDT switch.
  For ease I will label its pins as such:

      A   B

      C   D

      E   F

  Cut a piece of ribbon cable about 1' long with 4 conductors.
  Strip and tin the wires then connect them to A, B, C and D.
  Cut two small pieces of wire and connect A-F and E-B.

  Tin and strip the other ends of the ribbon cable.Using the snippers
 trim these tinned ends until there is about 1 1/2 to 2mm showing. Any
 longer is unnecessary and can lead to solder blobs etc.

  Grab the Amiga pc board again. On the solder side locate pins 9 and
 11 of CN11 as described earlier. Solder the lead from A to pin 9 and
 the lead from B to pin 11.

  Locate pins 13 and 14 of U8.

  If you are unsure of pin numbering on IC's refer to one of the data
 sections of DSE's or ROD Irving catalogues.  Otherwise looking at the
 chip there is a notch at the right hand end of the board. Pin 1 is
 behind this notch (relative to the pc board) and the numbers increase
 in an anti-clockwise fashion around the chip.  Solder the lead from C
 to pin 13 of U8 and the lead from D to pin 14 of U8.  That completes
 the soldering side of things.

  All that remains is to drill a hole for the switch and put the rest
 back together. There is a convenient spot to the right of the joystick
 socket that will house 3 or 4 switches comfortably.

  PLEASE PLEASE PLEASE be careful of the orientation of the connectors
 when assembling your amiga.

  To use the mod:
           1. Remove ALL disks from ALL drives.
           2. Flick the switch to the NORMAL position.
           3. Turn the machine ON or reset if already ON.
           4. If you wish to boot from drive DF1: now is the time to
              flick the switch to the NON-standard position.
           5. Insert the appropriate disks in the appropriate drives.

  HOW it works.
 The mod works by switching the drive select lines SEL_0 and SEL_1.
 SIMPLE!

  IMPORTANT:!!
 The switch must be in the NORMAL position when you either turn the
 machine on or reset.The reason for this is that after a cold or warm
 boot the KERNEL roms go looking for what equipment is connected to the
 system. A part of the GARY chip which is triggered by the SEL_0 signal
 provides seperate MOTOR_ON signals for the internal and external
 drives. When the switch is in the ALTERED position the GARY chip is
 fed by the SEL_1 signal and surprise surprise! the KERNEL roms won't
 find the internal drive!  However is is PERFECTLY safe to change the
 switch at ANY time the power is on (without disks in the drives!). So
 if the switch is changed after the roms have found what drives are
 online, the drives 0 and 1 will operate fine only reversed.  More
 circuitry could have been added to swap the motor_on signals so that
 this extra switching wasn't required, however most people would
 probably like to keep their mods to the main pcb to a MINIMUM!

• NOTE*

If the switch is changed while disks are inserted in the drives,

 AmigaDOS will become confused as to what volumes are on line and if
 your write-protect tags are OFF, chances are your directories will be
 CLOBBERED!!

  The mod is relatively simple, however if you are unsure of your
 ability to perform it.. DON'T. get some hardware oriented person to
 help or drop me a line at PARAGON bbs if in Sydney, or via Megadisc and
 I may be able to help or do it for you at a small nominal cost.
 Naturally I cannot guarantee your labour content so therefore I cannot
 make any warranties, implied or otherwise, as to the suitability or
 performance of this modification.  However I can say that I am not too
 worried about my software collection as I have a set of bootable 5 1/4"
 backups!!

  Good luck and I hope that this is of some help.

  ||||||||||||||||||||||| END OF BOOT_FROM_DF1 ||||||||||||||||||||||||