GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


archive:computers:a500_1mb

This is the CORRECT way to make your A501 chip ram!!

There have been other docs floating around saying to toggle the JP7A jumper, but this is not true! Clear it instead! For all of you who have tried the A501 chip ram fix and got nothing but a system crash on bootup, this is the doc 4 u :-)

Thanks to Greg Change (gchance@ecst.csuchico.edu) for information on how to correctly do this :-)

   <<<DIRECTIONS ON HOW TO CONVERT YOUR A501 CARTRIDGE TO CHIP RAM>>>

DISCLAIMER: Attempting to conduct this procedure will by all means VOID YOUR

          WARRANTY! I shall not be held responsible for any problems due
          to this modification. I shall not be held responsible for any 
          problems whatsoever.

Now I've got myself covered, lets' go on.

First off, it is required you have a revision 6A motherboard for this pro- ject. It will work with others, but requires a 1mb Agnus chip and also re- quires cutting a trace, which I am not familiar with at the moment.

If you are unfamiliar with electronic repair and modifications, ask an ex- perienced technician to proceed with the modification.

READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE INITATING PROCEDURE!!

Tools needed:

#10 Torx Screwdriver
Flat Head Screwdriver
Low Power Soldering Iron
Razor Blade or Exacto-Knife  
Anti-Static Guard (optional)
   

1. Turn off computer and unplug ALL cords and peripherals from the computer.

 This includes the A501.

2. Now carefully flip the computer over. WARNING! Do NOT grab the A500 on

 the left side if the expansion dust cover is off! If you tug hard enough,
 you will snap off the connector, and the only way to replace that is by
 buying a new motherboard! It's just an edge-connector and can snap easily.
    

3. Plug in the soldering iron, just to get it all nice and warm. (make sure

 the iron has been on for at LEAST 15 minutes to avoid cold solder joints.
 

4. Now take the #10 Torx screwdriver and remove the 6 Torx screws around the

 edge of the case (at this point the bottom is facing up, of course. Do
 NOT remove any other screws on the bottom of your computer. Save the po-
 sition of each screw, because some may be intentionally different lengths
 

5. Flip the computer over again and carefully remove the top. If it doesn't

 remove with ease, use the flat head screwdriver to pry open the sides.
 Using a large screwdriver will make less pry marks in the case, or put a
 cloth around it or something. :-) Hopefully this won't permanently de-
 stroy the latches in the sides. They should just snap right back togethor
 

6. Now remove the cable going from the keyboard to the socket on the mother-

 board. It should just pull right out.
 

7. Now take the keyboard out and set it off to the side for now.

8. Now remove the two Torx screws on the left side of the computer facing

 the front. Remove the other two Torx screws holding down the grounding
 plate of the external expansion port. Now carefully remove these screws
 and the grounding plate. Remember the positions of each screw! Try not
 to mix them up! Also- Make note of the text under the disk drive. It
 should tell you the model, "B52/ROCK LOBSTER" (if you're lucky) and some
 other junk. Now look for the text "Rev. 6A". If your motherboard is not
 6A, like I mentioned before, you can still do the mod, but you need to
 cut a special trace and unfortunately, I cannot help you with this.
 

9. Now is the time to don your anti-static wrist strap, or whatever have

 you.
 

10. Look around the edge of the RF shield for small metal tabs holding the

  cover down. Now carefully bend these tabs up with the flat head screw-
  driver. Becareful not to bend them too much, or they will snap off.
  This is what happened to mine. :-)
  

11. Now remove the RF shield cover.

12. Get ready, here is the time to do the modification. Be careful not to

  hit the Amiga's plastic case with the soldering iron. I did this on some
  practice soldering equipment (broken VCR's etc) a while ago and once you
  destroy the case you're Amiga will no longer look pretty. (thank god I
  didn't do THIS :-)

Left| Side| *BE CAREFUL WHEN CUTTING - Be careful NOT to cut any other traces* of | Ami | Fig 1

 ++   ____

E :: -| |- X :: -| |- P :: -| M |- 1| 13. Now locate Jumper 2 (JP2) Between the CPU A :: -| C |- | JP2 and the ROM chip (just above and left of N :: -| 6 |- 2| _ the ROM chip.) The jumper consists of three S :: -| 8 |- =| |= solder "pads". See how Fig 1 has these pads I P:: -| 0 |- 3| =|R|= numbered. When your computer arrived, pads O O:: -| 0 |- =|O|= 2 and 3 should have been set. We are about N R:: -| 0 |- =|M|= to change this. Now take your razor blade

T:: -|    |-    =| |=     or Xacto knife and just the trace between
 :: -|____|-    =|_|=     pad 2 and 3. Make sure, and check with a multi-
 ++                       meter or magnifying glass that there is no 
                          connection between these two pads. Now take
                          your HOT soldering iron and solder, and 
                          connect pads 2 and 1, just like the jumper
             =            depicted in Fig 1. Make sure it is a solid
             = Fig 2      connection and not a cold joint.
             =
             =
             =        14. Now it is time to locate the other jumper,
      JP7A   =            which is just left of the connector to the
             =            trapdoor (where the A501 goes). Search for
        1|   = Trapdoor   another three-padded jumper, labeled "JP7A"
             =            or JP7. Now cut the trace which was connecting
        2|   =            pads 2 and 3. Make sure it is a clean, solid 
             =            cut. This jumper should be left open, and no
        3|   =            pad should be soldered to another.
             =
             =
             =
             

15. Now check and make sure all connections are firm and clean, and replace

  the RF cover. Then push down the metal tabs and make sure the cover is
  secure at those points.
  

16. Now replace the grounding plate and CAREFULLY screw the two Torx screws

  in. These are special screws- so as soon as it feels firm, no NOT turn
  ANY further! This can strip the screwholes and damage your case perm-
  enantly. Remember to put each screw in it's dedicated position.
  

17. Now replace the other two Torx screws and once again screw them in just

  until secure. Remember once again to put each screw in it's dedicated
  position.
  

18. Replace the keyboard and set it in the special slots so it is secure.

  Carefully replace the keyboard cord, and make SURE it is inserted the
  correct way. If it is not then I cannot guarantee your system will boot
  up and work correctly.
  

19. Now snap the top case of the A500 back on. Make sure it is perfectly

  aligned and all.
  

20. Now carefully flip over the A500, and remember not to grab the edge-

  connector! I have never seen this incedent happen but I'm sure it has.
  Such a simple mistake could cost you a whole new computer/motherboard.
  

21. Now insert each Torx screw. And once again remember to put each screw

  in it's dedicated position. (whew!)
  

22. Now return the A501 to the trapdoor, close it up and flip the Amiga

  over. (and now I KNOW you know not to grab the edge-connector :-)
  

23. Plug all other peripherals and cords back in, and turn the machine on.

24. If it boots up O.K, then hopefully you're in buisness. Now run a program

  like SysInfo or PerfMon to make sure you have 1024k of chip ram (1mb)
  

25. Have fun! It is now possible to load large large mods, have more graphic

  data in memory at once, play better demos, and, in short, fit along with
  the rest of the world! :-) Good luck!
  

*** If you are having any problems I encourage you to check all of these

  steps and make sure nothing was left out or improperly done.
  
  Stay Cool with your new 1mb of Chip Ram,
 
  Bill The Cat (wjhun@oswego.edu)
   (Will Jhun)
      
/home/gen.uk/domains/wiki.gen.uk/public_html/data/pages/archive/computers/a500_1mb.txt · Last modified: 1999/10/13 05:04 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki