GENWiki

Premier IT Outsourcing and Support Services within the UK

User Tools

Site Tools


archive:music:mac-midi

From: ace@tidbits.com (Adam C. Engst) Subject: [*] minimal-midi-interface.txt Date: Sat, 22 May 93 08:24:20 PDT

(Oops, I specifically wanted this stored in a /report type directory so that I could refer to it in the final installment of the TidBITS MIDI series. Thanks! :-) -ace)

Here's a schematic for creating a simple MIDI interface for the Mac. It's a bit old, from what I gather from the person who sent it to me, and the address may not be valid for the author any more. Of course, I have no idea if these plans work. :-)

cheers … Adam C. Engst, TidBITS Editor

                      MINIMAL MAC--MIDI INTERFACE
                      ===========================

Well, here it is all you MIDI fans. THE ultimate in simplicity!! This is a simple schematic for a serial to MIDI converter.

There are two functions performed here. One is the conversion from current loop to RS-422. The second function is supplying the 1 MHz signal for the serial chip to sync up with the 31.5K baud rate of MIDI.

Macintosh MIDI Serial port 5 pin DIN DB9 pin numbers pin numbers

       +-------+     +------+
 4   10|26LS32 |     |7407  |
>------+       |11  1|      |2    220 ohm     5
 5    9|       +-----+      +------/\/\/-------< \
>------+       |     |      |                     \
       |       |     |      |                      | MIDI OUT
       +-------+     +------+                     /
                                  220 ohm     4  /
        390 ohm        +5 volts ---/\/\/-------<

+5 volts –/\/\/—-+

                  |
       +-------+  |  +------+1    220 ohm     4
 8    6|26LS31 |  |  |MCT2  +------/\/\/-------< \
>------+       |11| 5|      |                     \
 9    5|       +--+--+      |                      | MIDI IN
>------+       |    4|      |2                5   /
       |       |   +-+      +------------------< /
       +-------+   | +------+
                   |
                   v
                 Ground
       +-------+     +------+
 7   10|26LS31 |     |1 MHZ |
>------+       |9   8| OSC  |
 3   11|       +-----+      |
>-------       |     |      |
       |       |     |      |
       +-------+     +------+
      Power connections:
                      GROUND  +5
                      -----   --
        7407          7       14
        26LS31        8,12    4,16
        26LS32        8,12    4,16
        OSCILLATOR    7       14

Notes:

The optical isolator MCT-2 above can probably be any relatively fast optical coupler. Note that the 390 ohm resistor may need to be adjusted to make sure the output does not saturate. Using a scope while feeding a MIDI signal in should show you whether the signal looks clean.

The diagram has been drawn to show MAC signals on the left and MIDI signals on the right. Also note that the MAC pin numbers are for the DB9 connector NOT the 8 pin mini-DIN connector!!

The age old question of where to get power for this always remains. On the pre-MAC-PLUSs, there was power available from the serial port connector. I solved this problem by finding a 7 VDC AC adapter at a parts store and using a 5 volt voltage regulator IC to bring it down to 5 volts. This is left as an exercise for the student…..

The 26LS31 and 26LS32 are the same type of chips which are used in the MAC for RS-422 conversion. I got them from a store in Santa Clara California (Anchor Electronics (408) 727-3693). They also have 1 Mhz Oscillators as well.

I have built several variations of this over the last two years and have had good success using a variety of music software with them.

John Hengesbach (205)772-1669

uunet!ingr!henges Intergraph Corporation Huntsville, AL 35807

/data/webs/external/dokuwiki/data/pages/archive/music/mac-midi.txt · Last modified: 2000/08/13 06:40 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki